From ed781d395f85192fc9debb33ae5b45e7111eacee Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 3 May 2012 00:44:52 +0200 Subject: [PATCH] ARM: ux500: switch over to Nomadik pinctrl driver This converts the Ux500 family to use the pinctrl driver for configuring pins. Acked-by: Stephen Warren Signed-off-by: Linus Walleij --- arch/arm/mach-ux500/board-mop500-pins.c | 819 ++++++++++++------------ arch/arm/mach-ux500/board-mop500.c | 21 +- arch/arm/mach-ux500/board-mop500.h | 6 +- 3 files changed, 411 insertions(+), 435 deletions(-) diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c index df5b190d331..28c456c2906 100644 --- a/arch/arm/mach-ux500/board-mop500-pins.c +++ b/arch/arm/mach-ux500/board-mop500-pins.c @@ -8,6 +8,7 @@ #include #include #include +#include #include #include @@ -26,399 +27,390 @@ enum custom_pin_cfg_t { static enum custom_pin_cfg_t pinsfor; -static pin_cfg_t mop500_pins_common[] = { - /* uMSP0 */ - GPIO12_MSP0_TXD, - GPIO13_MSP0_TFS, - GPIO14_MSP0_TCK, - GPIO15_MSP0_RXD, - - /* MSP2: HDMI */ - GPIO193_MSP2_TXD | PIN_INPUT_PULLDOWN, - GPIO194_MSP2_TCK | PIN_INPUT_PULLDOWN, - GPIO195_MSP2_TFS | PIN_INPUT_PULLDOWN, - GPIO196_MSP2_RXD | PIN_OUTPUT_LOW, - - /* LCD TE0 */ - GPIO68_LCD_VSI0 | PIN_INPUT_PULLUP, - - /* Touch screen INTERFACE */ - GPIO84_GPIO | PIN_INPUT_PULLUP, /* TOUCH_INT1 */ - - /* STMPE1601/tc35893 keypad IRQ */ - GPIO218_GPIO | PIN_INPUT_PULLUP, - - /* UART */ - /* uart-0 pins gpio configuration should be - * kept intact to prevent glitch in tx line - * when tty dev is opened. Later these pins +/* These simply sets bias for pins */ +#define BIAS(a,b) static unsigned long a[] = { b } + +BIAS(pd, PIN_PULL_DOWN); +BIAS(slpm_gpio_nopull, PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL); +BIAS(in_nopull, PIN_INPUT_NOPULL); +BIAS(in_pu, PIN_INPUT_PULLUP); +BIAS(in_pd, PIN_INPUT_PULLDOWN); +BIAS(in_pd_slpm_in_pu, PIN_INPUT_PULLDOWN|PIN_SLPM_INPUT_PULLUP); +BIAS(in_pu_slpm_out_lo, PIN_INPUT_PULLUP|PIN_SLPM_OUTPUT_LOW); +BIAS(out_hi, PIN_OUTPUT_HIGH); +BIAS(out_lo, PIN_OUTPUT_LOW); +/* These also force them into GPIO mode */ +BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED); +BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED); +BIAS(gpio_in_pu_slpm_gpio_nopull, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL); +BIAS(gpio_in_pd_slpm_gpio_nopull, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL); +BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED); +BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED); + +/* We use these to define hog settings that are always done on boot */ +#define DB8500_MUX_HOG(group,func) \ + PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-db8500", group, func) +#define DB8500_PIN_HOG(pin,conf) \ + PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-db8500", pin, conf) + +/* These are default states associated with device and changed runtime */ +#define DB8500_MUX(group,func,dev) \ + PIN_MAP_MUX_GROUP_DEFAULT(dev, "pinctrl-db8500", group, func) +#define DB8500_PIN(pin,conf,dev) \ + PIN_MAP_CONFIGS_PIN_DEFAULT(dev, "pinctrl-db8500", pin, conf) + +/* Pin control settings */ +static struct pinctrl_map __initdata mop500_family_pinmap[] = { + /* + * uMSP0, mux in 4 pins, regular placement of RX/TX + * explicitly set the pins to no pull + */ + DB8500_MUX_HOG("msp0txrx_a_1", "msp0"), + DB8500_MUX_HOG("msp0tfstck_a_1", "msp0"), + DB8500_PIN_HOG("GPIO12_AC4", in_nopull), /* TXD */ + DB8500_PIN_HOG("GPIO15_AC3", in_nopull), /* RXD */ + DB8500_PIN_HOG("GPIO13_AF3", in_nopull), /* TFS */ + DB8500_PIN_HOG("GPIO14_AE3", in_nopull), /* TCK */ + /* MSP2 for HDMI, pull down TXD, TCK, TFS */ + DB8500_MUX_HOG("msp2_a_1", "msp2"), + DB8500_PIN_HOG("GPIO193_AH27", in_pd), /* TXD */ + DB8500_PIN_HOG("GPIO194_AF27", in_pd), /* TCK */ + DB8500_PIN_HOG("GPIO195_AG28", in_pd), /* TFS */ + DB8500_PIN_HOG("GPIO196_AG26", out_lo), /* RXD */ + /* + * LCD, set TE0 (using LCD VSI0) and D14 (touch screen interrupt) to + * pull-up + * TODO: is this really correct? Snowball doesn't have a LCD. + */ + DB8500_MUX_HOG("lcdvsi0_a_1", "lcd"), + DB8500_PIN_HOG("GPIO68_E1", in_pu), + DB8500_PIN_HOG("GPIO84_C2", gpio_in_pu), + /* + * STMPE1601/tc35893 keypad IRQ GPIO 218 + * TODO: set for snowball and HREF really?? + */ + DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu), + /* + * UART0, we do not mux in u0 here. + * uart-0 pins gpio configuration should be kept intact to prevent + * a glitch in tx line when the tty dev is opened. Later these pins * are configured to uart mop500_pins_uart0 - * - * It will be replaced with uart configuration - * once the issue is solved. */ - GPIO0_GPIO | PIN_INPUT_PULLUP, - GPIO1_GPIO | PIN_OUTPUT_HIGH, - GPIO2_GPIO | PIN_INPUT_PULLUP, - GPIO3_GPIO | PIN_OUTPUT_HIGH, - - GPIO29_U2_RXD | PIN_INPUT_PULLUP, - GPIO30_U2_TXD | PIN_OUTPUT_HIGH, - GPIO31_U2_CTSn | PIN_INPUT_PULLUP, - GPIO32_U2_RTSn | PIN_OUTPUT_HIGH, + DB8500_PIN_HOG("GPIO0_AJ5", in_pu), /* CTS */ + DB8500_PIN_HOG("GPIO1_AJ3", out_hi), /* RTS */ + DB8500_PIN_HOG("GPIO2_AH4", in_pu), /* RXD */ + DB8500_PIN_HOG("GPIO3_AH3", out_hi), /* TXD */ + /* + * Mux in UART2 on altfunction C and set pull-ups. + * TODO: is this used on U8500 variants and Snowball really? + * The setting on GPIO31 conflicts with magnetometer use on hrefv60 + */ + DB8500_MUX_HOG("u2rxtx_c_1", "u2"), + DB8500_MUX_HOG("u2ctsrts_c_1", "u2"), + DB8500_PIN_HOG("GPIO29_W2", in_pu), /* RXD */ + DB8500_PIN_HOG("GPIO30_W3", out_hi), /* TXD */ + DB8500_PIN_HOG("GPIO31_V3", in_pu), /* CTS */ + DB8500_PIN_HOG("GPIO32_V2", out_hi), /* RTS */ + /* + * The following pin sets were known as "runtime pins" before being + * converted to the pinctrl model. Here we model them as "default" + * states. + */ + /* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */ + DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"), + DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"), + /* Mux in LCD VSI1 and pull it up for MCDE HDMI output */ + DB8500_MUX("lcdvsi1_a_1", "lcd", "av8100-hdmi"), + /* Mux in I2C blocks, put pins into GPIO in sleepmode no pull-up */ + DB8500_MUX("i2c0_a_1", "i2c0", "nmk-i2c.0"), + DB8500_PIN("GPIO147_C15", slpm_gpio_nopull, "nmk-i2c.0"), + DB8500_PIN("GPIO148_B16", slpm_gpio_nopull, "nmk-i2c.0"), + DB8500_MUX("i2c1_b_2", "i2c1", "nmk-i2c.1"), + DB8500_PIN("GPIO16_AD3", slpm_gpio_nopull, "nmk-i2c.1"), + DB8500_PIN("GPIO17_AD4", slpm_gpio_nopull, "nmk-i2c.1"), + DB8500_MUX("i2c2_b_2", "i2c2", "nmk-i2c.2"), + DB8500_PIN("GPIO10_AF5", slpm_gpio_nopull, "nmk-i2c.2"), + DB8500_PIN("GPIO11_AG4", slpm_gpio_nopull, "nmk-i2c.2"), + DB8500_MUX("i2c3_c_2", "i2c3", "nmk-i2c.3"), + DB8500_PIN("GPIO229_AG7", slpm_gpio_nopull, "nmk-i2c.3"), + DB8500_PIN("GPIO230_AF7", slpm_gpio_nopull, "nmk-i2c.3"), + /* Mux in SDI0 (here called MC0) used for removable MMC/SD/SDIO cards */ + DB8500_MUX("mc0_a_1", "mc0", "sdi0"), + DB8500_PIN("GPIO18_AC2", out_hi, "sdi0"), /* CMDDIR */ + DB8500_PIN("GPIO19_AC1", out_hi, "sdi0"), /* DAT0DIR */ + DB8500_PIN("GPIO20_AB4", out_hi, "sdi0"), /* DAT2DIR */ + DB8500_PIN("GPIO22_AA3", in_nopull, "sdi0"), /* FBCLK */ + DB8500_PIN("GPIO23_AA4", out_lo, "sdi0"), /* CLK */ + DB8500_PIN("GPIO24_AB2", in_pu, "sdi0"), /* CMD */ + DB8500_PIN("GPIO25_Y4", in_pu, "sdi0"), /* DAT0 */ + DB8500_PIN("GPIO26_Y2", in_pu, "sdi0"), /* DAT1 */ + DB8500_PIN("GPIO27_AA2", in_pu, "sdi0"), /* DAT2 */ + DB8500_PIN("GPIO28_AA1", in_pu, "sdi0"), /* DAT3 */ + /* Mux in SDI1 (here called MC1) used for SDIO for CW1200 WLAN */ + DB8500_MUX("mc1_a_1", "mc1", "sdi1"), + DB8500_PIN("GPIO208_AH16", out_lo, "sdi1"), /* CLK */ + DB8500_PIN("GPIO209_AG15", in_nopull, "sdi1"), /* FBCLK */ + DB8500_PIN("GPIO210_AJ15", in_pu, "sdi1"), /* CMD */ + DB8500_PIN("GPIO211_AG14", in_pu, "sdi1"), /* DAT0 */ + DB8500_PIN("GPIO212_AF13", in_pu, "sdi1"), /* DAT1 */ + DB8500_PIN("GPIO213_AG13", in_pu, "sdi1"), /* DAT2 */ + DB8500_PIN("GPIO214_AH15", in_pu, "sdi1"), /* DAT3 */ + /* Mux in SDI2 (here called MC2) used for for PoP eMMC */ + DB8500_MUX("mc2_a_1", "mc2", "sdi2"), + DB8500_PIN("GPIO128_A5", out_lo, "sdi2"), /* CLK */ + DB8500_PIN("GPIO129_B4", in_pu, "sdi2"), /* CMD */ + DB8500_PIN("GPIO130_C8", in_nopull, "sdi2"), /* FBCLK */ + DB8500_PIN("GPIO131_A12", in_pu, "sdi2"), /* DAT0 */ + DB8500_PIN("GPIO132_C10", in_pu, "sdi2"), /* DAT1 */ + DB8500_PIN("GPIO133_B10", in_pu, "sdi2"), /* DAT2 */ + DB8500_PIN("GPIO134_B9", in_pu, "sdi2"), /* DAT3 */ + DB8500_PIN("GPIO135_A9", in_pu, "sdi2"), /* DAT4 */ + DB8500_PIN("GPIO136_C7", in_pu, "sdi2"), /* DAT5 */ + DB8500_PIN("GPIO137_A7", in_pu, "sdi2"), /* DAT6 */ + DB8500_PIN("GPIO138_C5", in_pu, "sdi2"), /* DAT7 */ + /* Mux in SDI4 (here called MC4) used for for PCB-mounted eMMC */ + DB8500_MUX("mc4_a_1", "mc4", "sdi4"), + DB8500_PIN("GPIO197_AH24", in_pu, "sdi4"), /* DAT3 */ + DB8500_PIN("GPIO198_AG25", in_pu, "sdi4"), /* DAT2 */ + DB8500_PIN("GPIO199_AH23", in_pu, "sdi4"), /* DAT1 */ + DB8500_PIN("GPIO200_AH26", in_pu, "sdi4"), /* DAT0 */ + DB8500_PIN("GPIO201_AF24", in_pu, "sdi4"), /* CMD */ + DB8500_PIN("GPIO202_AF25", in_nopull, "sdi4"), /* FBCLK */ + DB8500_PIN("GPIO203_AE23", out_lo, "sdi4"), /* CLK */ + DB8500_PIN("GPIO204_AF23", in_pu, "sdi4"), /* DAT7 */ + DB8500_PIN("GPIO205_AG23", in_pu, "sdi4"), /* DAT6 */ + DB8500_PIN("GPIO206_AG24", in_pu, "sdi4"), /* DAT5 */ + DB8500_PIN("GPIO207_AJ23", in_pu, "sdi4"), /* DAT4 */ + /* Mux in USB pins, drive STP high */ + DB8500_MUX("usb_a_1", "usb", "musb-ux500.0"), + DB8500_PIN("GPIO257_AE29", out_hi, "musb-ux500.0"), /* STP */ + /* Mux in SPI2 pins on the "other C1" altfunction */ + DB8500_MUX("spi2_oc1_1", "spi2", "spi2"), + DB8500_PIN("GPIO216_AG12", gpio_out_hi, "spi2"), /* FRM */ + DB8500_PIN("GPIO218_AH11", in_pd, "spi2"), /* RXD */ + DB8500_PIN("GPIO215_AH13", out_lo, "spi2"), /* TXD */ + DB8500_PIN("GPIO217_AH12", out_lo, "spi2"), /* CLK */ }; -static pin_cfg_t mop500_pins_default[] = { - /* SSP0 */ - GPIO143_SSP0_CLK, - GPIO144_SSP0_FRM, - GPIO145_SSP0_RXD | PIN_PULL_DOWN, - GPIO146_SSP0_TXD, - - /* XENON Flashgun INTERFACE */ - GPIO6_IP_GPIO0 | PIN_INPUT_PULLUP,/* XENON_FLASH_ID */ - GPIO7_IP_GPIO1 | PIN_INPUT_PULLUP,/* XENON_READY */ - - GPIO217_GPIO | PIN_INPUT_PULLUP, /* TC35892 IRQ */ - - /* sdi0 (removable MMC/SD/SDIO cards) not handled by pm_runtime */ - GPIO21_MC0_DAT31DIR | PIN_OUTPUT_HIGH, - - /* UART */ - GPIO4_U1_RXD | PIN_INPUT_PULLUP, - GPIO5_U1_TXD | PIN_OUTPUT_HIGH, - GPIO6_U1_CTSn | PIN_INPUT_PULLUP, - GPIO7_U1_RTSn | PIN_OUTPUT_HIGH, +/* + * These are specifically for the MOP500 and HREFP (pre-v60) version of the + * board, which utilized a TC35892 GPIO expander instead of using a lot of + * on-chip pins as the HREFv60 and later does. + */ +static struct pinctrl_map __initdata mop500_pinmap[] = { + /* Mux in SSP0, pull down RXD pin */ + DB8500_MUX_HOG("ssp0_a_1", "ssp0"), + DB8500_PIN_HOG("GPIO145_C13", pd), + /* + * XENON Flashgun on image processor GPIO (controlled from image + * processor firmware), mux in these image processor GPIO lines 0 + * (XENON_FLASH_ID) and 1 (XENON_READY) on altfunction C and pull up + * the pins. + */ + DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"), + DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"), + DB8500_PIN_HOG("GPIO6_AF6", in_pu), + DB8500_PIN_HOG("GPIO7_AG5", in_pu), + /* TC35892 IRQ, pull up the line, let the driver mux in the pin */ + DB8500_PIN_HOG("GPIO217_AH12", gpio_in_pu), + /* Mux in UART1 and set the pull-ups */ + DB8500_MUX_HOG("u1rxtx_a_1", "u1"), + DB8500_MUX_HOG("u1ctsrts_a_1", "u1"), + DB8500_PIN_HOG("GPIO4_AH6", in_pu), /* RXD */ + DB8500_PIN_HOG("GPIO5_AG6", out_hi), /* TXD */ + DB8500_PIN_HOG("GPIO6_AF6", in_pu), /* CTS */ + DB8500_PIN_HOG("GPIO7_AG5", out_hi), /* RTS */ + /* + * Runtime stuff: make it possible to mux in the SKE keypad + * and bias the pins + */ + DB8500_MUX("kp_a_2", "kp", "ske"), + DB8500_PIN("GPIO153_B17", in_pd_slpm_in_pu, "ske"), /* I7 */ + DB8500_PIN("GPIO154_C16", in_pd_slpm_in_pu, "ske"), /* I6 */ + DB8500_PIN("GPIO155_C19", in_pd_slpm_in_pu, "ske"), /* I5 */ + DB8500_PIN("GPIO156_C17", in_pd_slpm_in_pu, "ske"), /* I4 */ + DB8500_PIN("GPIO161_D21", in_pd_slpm_in_pu, "ske"), /* I3 */ + DB8500_PIN("GPIO162_D20", in_pd_slpm_in_pu, "ske"), /* I2 */ + DB8500_PIN("GPIO163_C20", in_pd_slpm_in_pu, "ske"), /* I1 */ + DB8500_PIN("GPIO164_B21", in_pd_slpm_in_pu, "ske"), /* I0 */ + DB8500_PIN("GPIO157_A18", in_pu_slpm_out_lo, "ske"), /* O7 */ + DB8500_PIN("GPIO158_C18", in_pu_slpm_out_lo, "ske"), /* O6 */ + DB8500_PIN("GPIO159_B19", in_pu_slpm_out_lo, "ske"), /* O5 */ + DB8500_PIN("GPIO160_B20", in_pu_slpm_out_lo, "ske"), /* O4 */ + DB8500_PIN("GPIO165_C21", in_pu_slpm_out_lo, "ske"), /* O3 */ + DB8500_PIN("GPIO166_A22", in_pu_slpm_out_lo, "ske"), /* O2 */ + DB8500_PIN("GPIO167_B24", in_pu_slpm_out_lo, "ske"), /* O1 */ + DB8500_PIN("GPIO168_C22", in_pu_slpm_out_lo, "ske"), /* O0 */ + /* Mux in and drive the SDI0 DAT31DIR line high at runtime */ + DB8500_MUX("mc0dat31dir_a_1", "mc0", "sdi0"), + DB8500_PIN("GPIO21_AB3", out_hi, "sdi0"), }; -static pin_cfg_t hrefv60_pins[] = { - /* WLAN */ - GPIO85_GPIO | PIN_OUTPUT_LOW,/* WLAN_ENA */ - - /* XENON Flashgun INTERFACE */ - GPIO6_IP_GPIO0 | PIN_INPUT_PULLUP,/* XENON_FLASH_ID */ - GPIO7_IP_GPIO1 | PIN_INPUT_PULLUP,/* XENON_READY */ - - /* Assistant LED INTERFACE */ - GPIO21_GPIO | PIN_OUTPUT_LOW, /* XENON_EN1 */ - GPIO64_IP_GPIO4 | PIN_OUTPUT_LOW, /* XENON_EN2 */ - - /* Magnetometer */ - GPIO31_GPIO | PIN_INPUT_PULLUP, /* magnetometer_INT */ - GPIO32_GPIO | PIN_INPUT_PULLDOWN, /* Magnetometer DRDY */ - - /* Display Interface */ - GPIO65_GPIO | PIN_OUTPUT_HIGH, /* DISP1 NO RST */ - GPIO66_GPIO | PIN_OUTPUT_LOW, /* DISP2 RST */ - - /* Touch screen INTERFACE */ - GPIO143_GPIO | PIN_OUTPUT_LOW,/*TOUCH_RST1 */ - - /* Touch screen INTERFACE 2 */ - GPIO67_GPIO | PIN_INPUT_PULLUP, /* TOUCH_INT2 */ - GPIO146_GPIO | PIN_OUTPUT_LOW,/*TOUCH_RST2 */ - - /* ETM_PTM_TRACE INTERFACE */ - GPIO70_GPIO | PIN_OUTPUT_LOW,/* ETM_PTM_DATA23 */ - GPIO71_GPIO | PIN_OUTPUT_LOW,/* ETM_PTM_DATA22 */ - GPIO72_GPIO | PIN_OUTPUT_LOW,/* ETM_PTM_DATA21 */ - GPIO73_GPIO | PIN_OUTPUT_LOW,/* ETM_PTM_DATA20 */ - GPIO74_GPIO | PIN_OUTPUT_LOW,/* ETM_PTM_DATA19 */ - - /* NAHJ INTERFACE */ - GPIO76_GPIO | PIN_OUTPUT_LOW,/* NAHJ_CTRL */ - GPIO216_GPIO | PIN_OUTPUT_HIGH,/* NAHJ_CTRL_INV */ - - /* NFC INTERFACE */ - GPIO77_GPIO | PIN_OUTPUT_LOW, /* NFC_ENA */ - GPIO144_GPIO | PIN_INPUT_PULLDOWN, /* NFC_IRQ */ - GPIO142_GPIO | PIN_OUTPUT_LOW, /* NFC_RESET */ - - /* Keyboard MATRIX INTERFACE */ - GPIO90_MC5_CMD | PIN_OUTPUT_LOW, /* KP_O_1 */ - GPIO87_MC5_DAT1 | PIN_OUTPUT_LOW, /* KP_O_2 */ - GPIO86_MC5_DAT0 | PIN_OUTPUT_LOW, /* KP_O_3 */ - GPIO96_KP_O6 | PIN_OUTPUT_LOW, /* KP_O_6 */ - GPIO94_KP_O7 | PIN_OUTPUT_LOW, /* KP_O_7 */ - GPIO93_MC5_DAT4 | PIN_INPUT_PULLUP, /* KP_I_0 */ - GPIO89_MC5_DAT3 | PIN_INPUT_PULLUP, /* KP_I_2 */ - GPIO88_MC5_DAT2 | PIN_INPUT_PULLUP, /* KP_I_3 */ - GPIO91_GPIO | PIN_INPUT_PULLUP, /* FORCE_SENSING_INT */ - GPIO92_GPIO | PIN_OUTPUT_LOW, /* FORCE_SENSING_RST */ - GPIO97_GPIO | PIN_OUTPUT_LOW, /* FORCE_SENSING_WU */ - - /* DiPro Sensor Interface */ - GPIO139_GPIO | PIN_INPUT_PULLUP, /* DIPRO_INT */ - - /* Audio Amplifier Interface */ - GPIO149_GPIO | PIN_OUTPUT_HIGH, /* VAUDIO_HF_EN, enable MAX8968 */ - - /* GBF INTERFACE */ - GPIO171_GPIO | PIN_OUTPUT_LOW, /* GBF_ENA_RESET */ - - /* MSP : HDTV INTERFACE */ - GPIO192_GPIO | PIN_INPUT_PULLDOWN, - - /* ACCELEROMETER_INTERFACE */ - GPIO82_GPIO | PIN_INPUT_PULLUP, /* ACC_INT1 */ - GPIO83_GPIO | PIN_INPUT_PULLUP, /* ACC_INT2 */ - - /* SD card detect */ - GPIO95_GPIO | PIN_INPUT_PULLUP, +/* + * The HREFv60 series of platforms is using available pins on the DB8500 + * insteaf of the Toshiba I2C GPIO expander, reusing some pins like the SSP0 + * and SSP1 ports (previously connected to the AB8500) as generic GPIO lines. + */ +static struct pinctrl_map __initdata hrefv60_pinmap[] = { + /* Drive WLAN_ENA low */ + DB8500_PIN_HOG("GPIO85_D5", gpio_out_lo), /* WLAN_ENA */ + /* + * XENON Flashgun on image processor GPIO (controlled from image + * processor firmware), mux in these image processor GPIO lines 0 + * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant + * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias + * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output. + */ + DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"), + DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"), + DB8500_MUX_HOG("ipgpio4_c_1", "ipgpio"), + DB8500_PIN_HOG("GPIO6_AF6", in_pu), /* XENON_FLASH_ID */ + DB8500_PIN_HOG("GPIO7_AG5", in_pu), /* XENON_READY */ + DB8500_PIN_HOG("GPIO21_AB3", gpio_out_lo), /* XENON_EN1 */ + DB8500_PIN_HOG("GPIO64_F3", out_lo), /* XENON_EN2 */ + /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */ + DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */ + DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */ + /* + * Display Interface 1 uses GPIO 65 for RST (reset). + * Display Interface 2 uses GPIO 66 for RST (reset). + * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset) + */ + DB8500_PIN_HOG("GPIO65_F1", gpio_out_hi), /* DISP1 NO RST */ + DB8500_PIN_HOG("GPIO66_G3", gpio_out_lo), /* DISP2 RST */ + /* + * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and + * GPIO 67 for interrupts. Pull-up the IRQ line and drive both + * reset signals low. + */ + DB8500_PIN_HOG("GPIO143_D12", gpio_out_lo), /* TOUCH_RST1 */ + DB8500_PIN_HOG("GPIO67_G2", gpio_in_pu), /* TOUCH_INT2 */ + DB8500_PIN_HOG("GPIO146_D13", gpio_out_lo), /* TOUCH_RST2 */ + /* + * Drive D19-D23 for the ETM PTM trace interface low, + * (presumably pins are unconnected therefore grounded here, + * the "other alt C1" setting enables these pins) + */ + DB8500_PIN_HOG("GPIO70_G5", gpio_out_lo), + DB8500_PIN_HOG("GPIO71_G4", gpio_out_lo), + DB8500_PIN_HOG("GPIO72_H4", gpio_out_lo), + DB8500_PIN_HOG("GPIO73_H3", gpio_out_lo), + DB8500_PIN_HOG("GPIO74_J3", gpio_out_lo), + /* NAHJ CTRL on GPIO 76 to low, CTRL_INV on GPIO216 to high */ + DB8500_PIN_HOG("GPIO76_J2", gpio_out_lo), /* CTRL */ + DB8500_PIN_HOG("GPIO216_AG12", gpio_out_hi), /* CTRL_INV */ + /* NFC ENA and RESET to low, pulldown IRQ line */ + DB8500_PIN_HOG("GPIO77_H1", gpio_out_lo), /* NFC_ENA */ + DB8500_PIN_HOG("GPIO144_B13", gpio_in_pd), /* NFC_IRQ */ + DB8500_PIN_HOG("GPIO142_C11", gpio_out_lo), /* NFC_RESET */ + /* + * SKE keyboard partly on alt A and partly on "Other alt C1" + * Driver KP_O1,2,3,6,7 low and pull up KP_I 0,2,3 for three + * rows of 6 keys, then pull up force sensing interrup and + * drive reset and force sensing WU low. + */ + DB8500_MUX_HOG("kp_a_1", "kp"), + DB8500_MUX_HOG("kp_oc1_1", "kp"), + DB8500_PIN_HOG("GPIO90_A3", out_lo), /* KP_O1 */ + DB8500_PIN_HOG("GPIO87_B3", out_lo), /* KP_O2 */ + DB8500_PIN_HOG("GPIO86_C6", out_lo), /* KP_O3 */ + DB8500_PIN_HOG("GPIO96_D8", out_lo), /* KP_O6 */ + DB8500_PIN_HOG("GPIO94_D7", out_lo), /* KP_O7 */ + DB8500_PIN_HOG("GPIO93_B7", in_pu), /* KP_I0 */ + DB8500_PIN_HOG("GPIO89_E6", in_pu), /* KP_I2 */ + DB8500_PIN_HOG("GPIO88_C4", in_pu), /* KP_I3 */ + DB8500_PIN_HOG("GPIO91_B6", gpio_in_pu), /* FORCE_SENSING_INT */ + DB8500_PIN_HOG("GPIO92_D6", gpio_out_lo), /* FORCE_SENSING_RST */ + DB8500_PIN_HOG("GPIO97_D9", gpio_out_lo), /* FORCE_SENSING_WU */ + /* DiPro Sensor interrupt */ + DB8500_PIN_HOG("GPIO139_C9", gpio_in_pu), /* DIPRO_INT */ + /* Audio Amplifier HF enable */ + DB8500_PIN_HOG("GPIO149_B14", gpio_out_hi), /* VAUDIO_HF_EN, enable MAX8968 */ + /* GBF interface, pull low to reset state */ + DB8500_PIN_HOG("GPIO171_D23", gpio_out_lo), /* GBF_ENA_RESET */ + /* MSP : HDTV INTERFACE GPIO line */ + DB8500_PIN_HOG("GPIO192_AJ27", gpio_in_pd), + /* Accelerometer interrupt lines */ + DB8500_PIN_HOG("GPIO82_C1", gpio_in_pu), /* ACC_INT1 */ + DB8500_PIN_HOG("GPIO83_D3", gpio_in_pu), /* ACC_INT2 */ + /* SD card detect GPIO pin */ + DB8500_PIN_HOG("GPIO95_E8", gpio_in_pu), + /* + * Runtime stuff + * Pull up/down of some sensor GPIO pins, for proximity, HAL sensor + * etc. + */ + DB8500_PIN("GPIO217_AH12", gpio_in_pu_slpm_gpio_nopull, "gpio-keys.0"), + DB8500_PIN("GPIO145_C13", gpio_in_pd_slpm_gpio_nopull, "gpio-keys.0"), + DB8500_PIN("GPIO139_C9", gpio_in_pu_slpm_gpio_nopull, "gpio-keys.0"), + /* + * Make it possible to mux in the SKE keypad and bias the pins + * FIXME: what's the point with this on HREFv60? KP/SKE is already + * muxed in at another place! Enabling this will bork. + */ + DB8500_MUX("kp_a_2", "kp", "ske"), + DB8500_PIN("GPIO153_B17", in_pd_slpm_in_pu, "ske"), /* I7 */ + DB8500_PIN("GPIO154_C16", in_pd_slpm_in_pu, "ske"), /* I6 */ + DB8500_PIN("GPIO155_C19", in_pd_slpm_in_pu, "ske"), /* I5 */ + DB8500_PIN("GPIO156_C17", in_pd_slpm_in_pu, "ske"), /* I4 */ + DB8500_PIN("GPIO161_D21", in_pd_slpm_in_pu, "ske"), /* I3 */ + DB8500_PIN("GPIO162_D20", in_pd_slpm_in_pu, "ske"), /* I2 */ + DB8500_PIN("GPIO163_C20", in_pd_slpm_in_pu, "ske"), /* I1 */ + DB8500_PIN("GPIO164_B21", in_pd_slpm_in_pu, "ske"), /* I0 */ + DB8500_PIN("GPIO157_A18", in_pu_slpm_out_lo, "ske"), /* O7 */ + DB8500_PIN("GPIO158_C18", in_pu_slpm_out_lo, "ske"), /* O6 */ + DB8500_PIN("GPIO159_B19", in_pu_slpm_out_lo, "ske"), /* O5 */ + DB8500_PIN("GPIO160_B20", in_pu_slpm_out_lo, "ske"), /* O4 */ + DB8500_PIN("GPIO165_C21", in_pu_slpm_out_lo, "ske"), /* O3 */ + DB8500_PIN("GPIO166_A22", in_pu_slpm_out_lo, "ske"), /* O2 */ + DB8500_PIN("GPIO167_B24", in_pu_slpm_out_lo, "ske"), /* O1 */ + DB8500_PIN("GPIO168_C22", in_pu_slpm_out_lo, "ske"), /* O0 */ }; -static pin_cfg_t u9500_pins[] = { - GPIO4_U1_RXD | PIN_INPUT_PULLUP, - GPIO5_U1_TXD | PIN_OUTPUT_HIGH, - GPIO144_GPIO | PIN_INPUT_PULLUP,/* WLAN_IRQ */ - +static struct pinctrl_map __initdata u9500_pinmap[] = { + /* Mux in UART1 (just RX/TX) and set the pull-ups */ + DB8500_MUX_HOG("u1rxtx_a_1", "u1"), + DB8500_PIN_HOG("GPIO4_AH6", in_pu), + DB8500_PIN_HOG("GPIO5_AG6", out_hi), + /* WLAN_IRQ line */ + DB8500_PIN_HOG("GPIO144_B13", gpio_in_pu), /* HSI */ - GPIO219_HSIR_FLA0 | PIN_INPUT_PULLDOWN, - GPIO220_HSIR_DAT0 | PIN_INPUT_PULLDOWN, - GPIO221_HSIR_RDY0 | PIN_OUTPUT_LOW, - GPIO222_HSIT_FLA0 | PIN_OUTPUT_LOW, - GPIO223_HSIT_DAT0 | PIN_OUTPUT_LOW, - GPIO224_HSIT_RDY0 | PIN_INPUT_PULLDOWN, - GPIO225_HSIT_CAWAKE0 | PIN_INPUT_PULLDOWN, /* CA_WAKE0 */ - GPIO226_GPIO | PIN_OUTPUT_HIGH, /* AC_WAKE0 */ + DB8500_MUX_HOG("hsir_a_1", "hsi"), + DB8500_MUX_HOG("hsit_a_1", "hsi"), + DB8500_PIN_HOG("GPIO219_AG10", in_pd), /* RX FLA0 */ + DB8500_PIN_HOG("GPIO220_AH10", in_pd), /* RX DAT0 */ + DB8500_PIN_HOG("GPIO221_AJ11", out_lo), /* RX RDY0 */ + DB8500_PIN_HOG("GPIO222_AJ9", out_lo), /* TX FLA0 */ + DB8500_PIN_HOG("GPIO223_AH9", out_lo), /* TX DAT0 */ + DB8500_PIN_HOG("GPIO224_AG9", in_pd), /* TX RDY0 */ + DB8500_PIN_HOG("GPIO225_AG8", in_pd), /* CAWAKE0 */ + DB8500_PIN_HOG("GPIO226_AF8", out_hi), /* ACWAKE0 */ }; -static pin_cfg_t u8500_pins[] = { - GPIO226_GPIO | PIN_OUTPUT_LOW, /* WLAN_PMU_EN */ - GPIO4_GPIO | PIN_INPUT_PULLUP,/* WLAN_IRQ */ +static struct pinctrl_map __initdata u8500_pinmap[] = { + DB8500_PIN_HOG("GPIO226_AF8", gpio_out_lo), /* WLAN_PMU_EN */ + DB8500_PIN_HOG("GPIO4_AH6", gpio_in_pu), /* WLAN_IRQ */ }; -static pin_cfg_t snowball_pins[] = { - /* SSP0, to AB8500 */ - GPIO143_SSP0_CLK, - GPIO144_SSP0_FRM, - GPIO145_SSP0_RXD | PIN_PULL_DOWN, - GPIO146_SSP0_TXD, - - /* MMC0: MicroSD card */ - GPIO21_MC0_DAT31DIR | PIN_OUTPUT_HIGH, - - /* MMC2: LAN */ - GPIO86_SM_ADQ0, - GPIO87_SM_ADQ1, - GPIO88_SM_ADQ2, - GPIO89_SM_ADQ3, - GPIO90_SM_ADQ4, - GPIO91_SM_ADQ5, - GPIO92_SM_ADQ6, - GPIO93_SM_ADQ7, - - GPIO94_SM_ADVn, - GPIO95_SM_CS0n, - GPIO96_SM_OEn, - GPIO97_SM_WEn, - - GPIO128_SM_CKO, - GPIO130_SM_FBCLK, - GPIO131_SM_ADQ8, - GPIO132_SM_ADQ9, - GPIO133_SM_ADQ10, - GPIO134_SM_ADQ11, - GPIO135_SM_ADQ12, - GPIO136_SM_ADQ13, - GPIO137_SM_ADQ14, - GPIO138_SM_ADQ15, - - /* RSTn_LAN */ - GPIO141_GPIO | PIN_OUTPUT_HIGH, - +static struct pinctrl_map __initdata snowball_pinmap[] = { + /* Mux in SSP0 connected to AB8500, pull down RXD pin */ + DB8500_MUX_HOG("ssp0_a_1", "ssp0"), + DB8500_PIN_HOG("GPIO145_C13", pd), + /* Always drive the MC0 DAT31DIR line high on these boards */ + DB8500_PIN_HOG("GPIO21_AB3", out_hi), + /* Mux in "SM" which is used for the SMSC911x Ethernet adapter */ + DB8500_MUX_HOG("sm_b_1", "sm"), + /* Drive RSTn_LAN high */ + DB8500_PIN_HOG("GPIO141_C12", gpio_out_hi), /* Accelerometer/Magnetometer */ - GPIO163_GPIO | PIN_INPUT_PULLUP, /* ACCEL_IRQ1 */ - GPIO164_GPIO | PIN_INPUT_PULLUP, /* ACCEL_IRQ2 */ - GPIO165_GPIO | PIN_INPUT_PULLUP, /* MAG_DRDY */ - + DB8500_PIN_HOG("GPIO163_C20", gpio_in_pu), /* ACCEL_IRQ1 */ + DB8500_PIN_HOG("GPIO164_B21", gpio_in_pu), /* ACCEL_IRQ2 */ + DB8500_PIN_HOG("GPIO165_C21", gpio_in_pu), /* MAG_DRDY */ /* WLAN/GBF */ - GPIO161_GPIO | PIN_OUTPUT_LOW, /* WLAN_PMU_EN */ - GPIO171_GPIO | PIN_OUTPUT_HIGH,/* GBF_ENA */ - GPIO215_GPIO | PIN_OUTPUT_LOW,/* WLAN_ENA */ - GPIO216_GPIO | PIN_INPUT_PULLUP,/* WLAN_IRQ */ -}; - -/* - * I2C - */ - -static UX500_PINS(mop500_pins_i2c0, - GPIO147_I2C0_SCL | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, - GPIO148_I2C0_SDA | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, -); - -static UX500_PINS(mop500_pins_i2c1, - GPIO16_I2C1_SCL | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, - GPIO17_I2C1_SDA | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, -); - -static UX500_PINS(mop500_pins_i2c2, - GPIO10_I2C2_SDA | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, - GPIO11_I2C2_SCL | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, -); - -static UX500_PINS(mop500_pins_i2c3, - GPIO229_I2C3_SDA | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, - GPIO230_I2C3_SCL | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, -); - -static UX500_PINS(mop500_pins_mcde_tvout, - GPIO78_LCD_D8, - GPIO79_LCD_D9, - GPIO80_LCD_D10, - GPIO81_LCD_D11, - GPIO150_LCDA_CLK, -); - -static UX500_PINS(mop500_pins_mcde_hdmi, - GPIO69_LCD_VSI1 | PIN_INPUT_PULLUP, -); - -static UX500_PINS(mop500_pins_ske, - GPIO153_KP_I7 | PIN_INPUT_PULLDOWN | PIN_SLPM_INPUT_PULLUP, - GPIO154_KP_I6 | PIN_INPUT_PULLDOWN | PIN_SLPM_INPUT_PULLUP, - GPIO155_KP_I5 | PIN_INPUT_PULLDOWN | PIN_SLPM_INPUT_PULLUP, - GPIO156_KP_I4 | PIN_INPUT_PULLDOWN | PIN_SLPM_INPUT_PULLUP, - GPIO161_KP_I3 | PIN_INPUT_PULLDOWN | PIN_SLPM_INPUT_PULLUP, - GPIO162_KP_I2 | PIN_INPUT_PULLDOWN | PIN_SLPM_INPUT_PULLUP, - GPIO163_KP_I1 | PIN_INPUT_PULLDOWN | PIN_SLPM_INPUT_PULLUP, - GPIO164_KP_I0 | PIN_INPUT_PULLDOWN | PIN_SLPM_INPUT_PULLUP, - GPIO157_KP_O7 | PIN_INPUT_PULLUP | PIN_SLPM_OUTPUT_LOW, - GPIO158_KP_O6 | PIN_INPUT_PULLUP | PIN_SLPM_OUTPUT_LOW, - GPIO159_KP_O5 | PIN_INPUT_PULLUP | PIN_SLPM_OUTPUT_LOW, - GPIO160_KP_O4 | PIN_INPUT_PULLUP | PIN_SLPM_OUTPUT_LOW, - GPIO165_KP_O3 | PIN_INPUT_PULLUP | PIN_SLPM_OUTPUT_LOW, - GPIO166_KP_O2 | PIN_INPUT_PULLUP | PIN_SLPM_OUTPUT_LOW, - GPIO167_KP_O1 | PIN_INPUT_PULLUP | PIN_SLPM_OUTPUT_LOW, - GPIO168_KP_O0 | PIN_INPUT_PULLUP | PIN_SLPM_OUTPUT_LOW, -); - -/* sdi0 (removable MMC/SD/SDIO cards) */ -static UX500_PINS(mop500_pins_sdi0, - GPIO18_MC0_CMDDIR | PIN_OUTPUT_HIGH, - GPIO19_MC0_DAT0DIR | PIN_OUTPUT_HIGH, - GPIO20_MC0_DAT2DIR | PIN_OUTPUT_HIGH, - - GPIO22_MC0_FBCLK | PIN_INPUT_NOPULL, - GPIO23_MC0_CLK | PIN_OUTPUT_LOW, - GPIO24_MC0_CMD | PIN_INPUT_PULLUP, - GPIO25_MC0_DAT0 | PIN_INPUT_PULLUP, - GPIO26_MC0_DAT1 | PIN_INPUT_PULLUP, - GPIO27_MC0_DAT2 | PIN_INPUT_PULLUP, - GPIO28_MC0_DAT3 | PIN_INPUT_PULLUP, -); - -/* sdi1 (WLAN CW1200) */ -static UX500_PINS(mop500_pins_sdi1, - GPIO208_MC1_CLK | PIN_OUTPUT_LOW, - GPIO209_MC1_FBCLK | PIN_INPUT_NOPULL, - GPIO210_MC1_CMD | PIN_INPUT_PULLUP, - GPIO211_MC1_DAT0 | PIN_INPUT_PULLUP, - GPIO212_MC1_DAT1 | PIN_INPUT_PULLUP, - GPIO213_MC1_DAT2 | PIN_INPUT_PULLUP, - GPIO214_MC1_DAT3 | PIN_INPUT_PULLUP, -); - -/* sdi2 (POP eMMC) */ -static UX500_PINS(mop500_pins_sdi2, - GPIO128_MC2_CLK | PIN_OUTPUT_LOW, - GPIO129_MC2_CMD | PIN_INPUT_PULLUP, - GPIO130_MC2_FBCLK | PIN_INPUT_NOPULL, - GPIO131_MC2_DAT0 | PIN_INPUT_PULLUP, - GPIO132_MC2_DAT1 | PIN_INPUT_PULLUP, - GPIO133_MC2_DAT2 | PIN_INPUT_PULLUP, - GPIO134_MC2_DAT3 | PIN_INPUT_PULLUP, - GPIO135_MC2_DAT4 | PIN_INPUT_PULLUP, - GPIO136_MC2_DAT5 | PIN_INPUT_PULLUP, - GPIO137_MC2_DAT6 | PIN_INPUT_PULLUP, - GPIO138_MC2_DAT7 | PIN_INPUT_PULLUP, -); - -/* sdi4 (PCB eMMC) */ -static UX500_PINS(mop500_pins_sdi4, - GPIO197_MC4_DAT3 | PIN_INPUT_PULLUP, - GPIO198_MC4_DAT2 | PIN_INPUT_PULLUP, - GPIO199_MC4_DAT1 | PIN_INPUT_PULLUP, - GPIO200_MC4_DAT0 | PIN_INPUT_PULLUP, - GPIO201_MC4_CMD | PIN_INPUT_PULLUP, - GPIO202_MC4_FBCLK | PIN_INPUT_NOPULL, - GPIO203_MC4_CLK | PIN_OUTPUT_LOW, - GPIO204_MC4_DAT7 | PIN_INPUT_PULLUP, - GPIO205_MC4_DAT6 | PIN_INPUT_PULLUP, - GPIO206_MC4_DAT5 | PIN_INPUT_PULLUP, - GPIO207_MC4_DAT4 | PIN_INPUT_PULLUP, -); - -/* USB */ -static UX500_PINS(mop500_pins_usb, - GPIO256_USB_NXT, - GPIO257_USB_STP | PIN_OUTPUT_HIGH, - GPIO258_USB_XCLK, - GPIO259_USB_DIR, - GPIO260_USB_DAT7, - GPIO261_USB_DAT6, - GPIO262_USB_DAT5, - GPIO263_USB_DAT4, - GPIO264_USB_DAT3, - GPIO265_USB_DAT2, - GPIO266_USB_DAT1, - GPIO267_USB_DAT0, -); - -/* SPI2 */ -static UX500_PINS(mop500_pins_spi2, - GPIO216_GPIO | PIN_OUTPUT_HIGH, - GPIO218_SPI2_RXD | PIN_INPUT_PULLDOWN, - GPIO215_SPI2_TXD | PIN_OUTPUT_LOW, - GPIO217_SPI2_CLK | PIN_OUTPUT_LOW, -); - -static UX500_PINS(mop500_pins_sensors1p_v60, - GPIO217_GPIO| PIN_INPUT_PULLUP | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, - GPIO145_GPIO | PIN_INPUT_PULLDOWN | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, - GPIO139_GPIO | PIN_INPUT_PULLUP | - PIN_SLPM_GPIO | PIN_SLPM_INPUT_NOPULL, -); - -static UX500_PINS(mop500_pins_sensors1p, - PIN_CFG_INPUT(GPIO_PROX_SENSOR, GPIO, NOPULL), - PIN_CFG_INPUT(GPIO_HAL_SENSOR, GPIO, NOPULL), -); - -static struct ux500_pin_lookup mop500_runtime_pins[] = { - PIN_LOOKUP("mcde-tvout", &mop500_pins_mcde_tvout), - PIN_LOOKUP("av8100-hdmi", &mop500_pins_mcde_hdmi), - PIN_LOOKUP("nmk-i2c.0", &mop500_pins_i2c0), - PIN_LOOKUP("nmk-i2c.1", &mop500_pins_i2c1), - PIN_LOOKUP("nmk-i2c.2", &mop500_pins_i2c2), - PIN_LOOKUP("nmk-i2c.3", &mop500_pins_i2c3), - PIN_LOOKUP("sdi0", &mop500_pins_sdi0), - PIN_LOOKUP("sdi1", &mop500_pins_sdi1), - PIN_LOOKUP("sdi2", &mop500_pins_sdi2), - PIN_LOOKUP("sdi4", &mop500_pins_sdi4), - PIN_LOOKUP("musb-ux500.0", &mop500_pins_usb), - PIN_LOOKUP("spi2", &mop500_pins_spi2), -}; - -static struct ux500_pin_lookup mop500_runtime_pins_v60[] = { - PIN_LOOKUP("ske", &mop500_pins_ske), - PIN_LOOKUP("gpio-keys.0", &mop500_pins_sensors1p_v60), -}; - -static struct ux500_pin_lookup mop500_runtime_pins_pre_v60[] = { - PIN_LOOKUP("ske", &mop500_pins_ske), - PIN_LOOKUP("gpio-keys.0", &mop500_pins_sensors1p), + DB8500_PIN_HOG("GPIO161_D21", gpio_out_lo), /* WLAN_PMU_EN */ + DB8500_PIN_HOG("GPIO171_D23", gpio_out_hi), /* GBF_ENA */ + DB8500_PIN_HOG("GPIO215_AH13", gpio_out_lo), /* WLAN_ENA */ + DB8500_PIN_HOG("GPIO216_AG12", gpio_in_pu), /* WLAN_IRQ */ }; /* @@ -444,64 +436,45 @@ int pins_for_u9500(void) return 0; } -void __init mop500_pins_init(void) +static void __init mop500_href_family_pinmaps_init(void) { - nmk_config_pins(mop500_pins_common, - ARRAY_SIZE(mop500_pins_common)); - - ux500_pins_add(mop500_runtime_pins, ARRAY_SIZE(mop500_runtime_pins)); - - ux500_pins_add(mop500_runtime_pins_pre_v60, - ARRAY_SIZE(mop500_runtime_pins_pre_v60)); - switch (pinsfor) { case PINS_FOR_U9500: - nmk_config_pins(u9500_pins, ARRAY_SIZE(u9500_pins)); + pinctrl_register_mappings(u9500_pinmap, + ARRAY_SIZE(u9500_pinmap)); break; - case PINS_FOR_DEFAULT: - nmk_config_pins(u8500_pins, ARRAY_SIZE(u8500_pins)); + pinctrl_register_mappings(u8500_pinmap, + ARRAY_SIZE(u8500_pinmap)); default: break; } - - nmk_config_pins(mop500_pins_default, - ARRAY_SIZE(mop500_pins_default)); } -void __init snowball_pins_init(void) +void __init mop500_pinmaps_init(void) { - nmk_config_pins(mop500_pins_common, - ARRAY_SIZE(mop500_pins_common)); - - ux500_pins_add(mop500_runtime_pins, ARRAY_SIZE(mop500_runtime_pins)); - - nmk_config_pins(u8500_pins, ARRAY_SIZE(u8500_pins)); - - nmk_config_pins(snowball_pins, ARRAY_SIZE(snowball_pins)); + pinctrl_register_mappings(mop500_family_pinmap, + ARRAY_SIZE(mop500_family_pinmap)); + pinctrl_register_mappings(mop500_pinmap, + ARRAY_SIZE(mop500_pinmap)); + mop500_href_family_pinmaps_init(); } -void __init hrefv60_pins_init(void) +void __init snowball_pinmaps_init(void) { - nmk_config_pins(mop500_pins_common, - ARRAY_SIZE(mop500_pins_common)); - - ux500_pins_add(mop500_runtime_pins, ARRAY_SIZE(mop500_runtime_pins)); - - ux500_pins_add(mop500_runtime_pins_v60, - ARRAY_SIZE(mop500_runtime_pins_v60)); - - nmk_config_pins(hrefv60_pins, - ARRAY_SIZE(hrefv60_pins)); - - switch (pinsfor) { - case PINS_FOR_U9500: - nmk_config_pins(u9500_pins, ARRAY_SIZE(u9500_pins)); - break; + pinctrl_register_mappings(mop500_family_pinmap, + ARRAY_SIZE(mop500_family_pinmap)); + pinctrl_register_mappings(snowball_pinmap, + ARRAY_SIZE(snowball_pinmap)); + pinctrl_register_mappings(u8500_pinmap, + ARRAY_SIZE(u8500_pinmap)); +} - case PINS_FOR_DEFAULT: - nmk_config_pins(u8500_pins, ARRAY_SIZE(u8500_pins)); - default: - break; - } +void __init hrefv60_pinmaps_init(void) +{ + pinctrl_register_mappings(mop500_family_pinmap, + ARRAY_SIZE(mop500_family_pinmap)); + pinctrl_register_mappings(hrefv60_pinmap, + ARRAY_SIZE(hrefv60_pinmap)); + mop500_href_family_pinmaps_init(); } diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c index ca0d62599f7..e5c0e6e25cf 100644 --- a/arch/arm/mach-ux500/board-mop500.c +++ b/arch/arm/mach-ux500/board-mop500.c @@ -1,3 +1,4 @@ + /* * Copyright (C) 2008-2009 ST-Ericsson * @@ -618,10 +619,9 @@ static void __init mop500_init_machine(void) mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR; + mop500_pinmaps_init(); parent = u8500_init_devices(); - mop500_pins_init(); - /* FIXME: parent of ab8500 should be prcmu */ for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++) mop500_platform_devs[i]->dev.parent = parent; @@ -651,10 +651,9 @@ static void __init snowball_init_machine(void) int i2c0_devs; int i; + snowball_pinmaps_init(); parent = u8500_init_devices(); - snowball_pins_init(); - for (i = 0; i < ARRAY_SIZE(snowball_platform_devs); i++) snowball_platform_devs[i]->dev.parent = parent; @@ -689,10 +688,9 @@ static void __init hrefv60_init_machine(void) */ mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO; + hrefv60_pinmaps_init(); parent = u8500_init_devices(); - hrefv60_pins_init(); - for (i = 0; i < ARRAY_SIZE(mop500_platform_devs); i++) mop500_platform_devs[i]->dev.parent = parent; @@ -781,6 +779,14 @@ static void __init u8500_init_machine(void) int i2c0_devs; int i; + /* Pinmaps must be in place before devices register */ + if (of_machine_is_compatible("st-ericsson,mop500")) + mop500_pinmaps_init(); + else if (of_machine_is_compatible("calaosystems,snowball-a9500")) + snowball_pinmaps_init(); + else if (of_machine_is_compatible("st-ericsson,hrefv60+")) + hrefv60_pinmaps_init(); + parent = u8500_init_devices(); i2c0_devs = ARRAY_SIZE(mop500_i2c0_devices); @@ -794,14 +800,12 @@ static void __init u8500_init_machine(void) if (of_machine_is_compatible("st-ericsson,mop500")) { mop500_gpio_keys[0].gpio = GPIO_PROX_SENSOR; - mop500_pins_init(); platform_add_devices(mop500_platform_devs, ARRAY_SIZE(mop500_platform_devs)); mop500_sdi_init(parent); } else if (of_machine_is_compatible("calaosystems,snowball-a9500")) { - snowball_pins_init(); platform_add_devices(snowball_platform_devs, ARRAY_SIZE(snowball_platform_devs)); @@ -814,7 +818,6 @@ static void __init u8500_init_machine(void) */ mop500_gpio_keys[0].gpio = HREFV60_PROX_SENSE_GPIO; i2c0_devs -= NUM_PRE_V60_I2C0_DEVICES; - hrefv60_pins_init(); platform_add_devices(mop500_platform_devs, ARRAY_SIZE(mop500_platform_devs)); diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h index 91dc63fe101..bc44c07c71a 100644 --- a/arch/arm/mach-ux500/board-mop500.h +++ b/arch/arm/mach-ux500/board-mop500.h @@ -85,9 +85,9 @@ extern void hrefv60_sdi_init(struct device *parent); extern void mop500_sdi_tc35892_init(struct device *parent); void __init mop500_u8500uib_init(void); void __init mop500_stuib_init(void); -void __init mop500_pins_init(void); -void __init hrefv60_pins_init(void); -void __init snowball_pins_init(void); +void __init mop500_pinmaps_init(void); +void __init snowball_pinmaps_init(void); +void __init hrefv60_pinmaps_init(void); void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info, unsigned n); -- 2.46.0