From e745a6676c76280f9721adeec79b08a0f2dfcc21 Mon Sep 17 00:00:00 2001 From: Magnus Damm Date: Tue, 16 Nov 2010 01:07:19 +0100 Subject: [PATCH] ARM: 6481/1: Use shared GIC entry macros on OMAP Common GIC entry macro for omap Signed-off-by: Tony Lindgren Signed-off-by: Magnus Damm Acked-by: Santosh Shilimkar Signed-off-by: Russell King --- .../arm/mach-omap2/include/mach/entry-macro.S | 92 +++++++------------ 1 file changed, 31 insertions(+), 61 deletions(-) diff --git a/arch/arm/mach-omap2/include/mach/entry-macro.S b/arch/arm/mach-omap2/include/mach/entry-macro.S index 06e64e1fc28..2e358df3fe1 100644 --- a/arch/arm/mach-omap2/include/mach/entry-macro.S +++ b/arch/arm/mach-omap2/include/mach/entry-macro.S @@ -105,6 +105,35 @@ omap_irq_base: .word 0 9999: .endm +#ifdef CONFIG_SMP + /* We assume that irqstat (the raw value of the IRQ acknowledge + * register) is preserved from the macro above. + * If there is an IPI, we immediately signal end of interrupt + * on the controller, since this requires the original irqstat + * value which we won't easily be able to recreate later. + */ + + .macro test_for_ipi, irqnr, irqstat, base, tmp + bic \irqnr, \irqstat, #0x1c00 + cmp \irqnr, #16 + it cc + strcc \irqstat, [\base, #GIC_CPU_EOI] + it cs + cmpcs \irqnr, \irqnr + .endm + + /* As above, this assumes that irqstat and base are preserved */ + + .macro test_for_ltirq, irqnr, irqstat, base, tmp + bic \irqnr, \irqstat, #0x1c00 + mov \tmp, #0 + cmp \irqnr, #29 + itt eq + moveq \tmp, #1 + streq \irqstat, [\base, #GIC_CPU_EOI] + cmp \tmp, #0 + .endm +#endif /* CONFIG_SMP */ #else /* MULTI_OMAP2 */ @@ -141,74 +170,15 @@ omap_irq_base: .word 0 #ifdef CONFIG_ARCH_OMAP4 +#include .macro get_irqnr_preamble, base, tmp ldr \base, =OMAP4_IRQ_BASE .endm - /* - * The interrupt numbering scheme is defined in the - * interrupt controller spec. To wit: - * - * Interrupts 0-15 are IPI - * 16-28 are reserved - * 29-31 are local. We allow 30 to be used for the watchdog. - * 32-1020 are global - * 1021-1022 are reserved - * 1023 is "spurious" (no interrupt) - * - * For now, we ignore all local interrupts so only return an - * interrupt if it's between 30 and 1020. The test_for_ipi - * routine below will pick up on IPIs. - * A simple read from the controller will tell us the number - * of the highest priority enabled interrupt. - * We then just need to check whether it is in the - * valid range for an IRQ (30-1020 inclusive). - */ - .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - ldr \irqstat, [\base, #GIC_CPU_INTACK] - - ldr \tmp, =1021 - - bic \irqnr, \irqstat, #0x1c00 - - cmp \irqnr, #29 - cmpcc \irqnr, \irqnr - cmpne \irqnr, \tmp - cmpcs \irqnr, \irqnr - .endm #endif -#endif /* MULTI_OMAP2 */ - -#ifdef CONFIG_SMP - /* We assume that irqstat (the raw value of the IRQ acknowledge - * register) is preserved from the macro above. - * If there is an IPI, we immediately signal end of interrupt - * on the controller, since this requires the original irqstat - * value which we won't easily be able to recreate later. - */ - .macro test_for_ipi, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - cmp \irqnr, #16 - it cc - strcc \irqstat, [\base, #GIC_CPU_EOI] - it cs - cmpcs \irqnr, \irqnr - .endm - - /* As above, this assumes that irqstat and base are preserved */ - - .macro test_for_ltirq, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - mov \tmp, #0 - cmp \irqnr, #29 - itt eq - moveq \tmp, #1 - streq \irqstat, [\base, #GIC_CPU_EOI] - cmp \tmp, #0 - .endm -#endif /* CONFIG_SMP */ +#endif /* MULTI_OMAP2 */ .macro irq_prio_table .endm -- 2.41.0