Ralf Baechle [Tue, 23 Jun 2009 09:20:56 +0000 (10:20 +0100)]
MIPS: SMP: Allow suspend and hibernation if CPU hotplug is available
The SMP implementation of suspend and hibernate depends on CPU hotplugging.
In the past we didn't have CPU hotplug so suspend and hibernation were not
possible on SMP systems.
Ralf Baechle [Tue, 23 Jun 2009 09:00:31 +0000 (10:00 +0100)]
MIPS: Add arch generic CPU hotplug
Each platform has to add support for CPU hotplugging itself by providing
suitable definitions for the cpu_disable and cpu_die of the smp_ops
methods and setting SYS_SUPPORTS_HOTPLUG_CPU. A platform should only set
SYS_SUPPORTS_HOTPLUG_CPU once all it's smp_ops definitions have the
necessary changes. This patch contains the changes to the dummy smp_ops
definition for uni-processor systems.
Ralf Baechle [Fri, 19 Jun 2009 14:01:44 +0000 (15:01 +0100)]
MIPS: Hibernation: Remove SMP TLB and cacheflushing code.
We can't perform any flushes on SMP from swsusp_arch_resume because
interrupts are disabled. A cross-CPU flush is unnecessary anyway
because all but the local CPU have already been disabled. A local
flush is not needed either because we didn't change any mappings. So
just delete the code.
Ralf Baechle [Fri, 19 Jun 2009 13:05:26 +0000 (14:05 +0100)]
MIPS: Build fix - include <linux/smp.h> into all smp_processor_id() users.
Some of the were relying into smp.h being dragged in by another header
which of course is fragile. <asm/cpu-info.h> uses smp_processor_id()
only in macros and including smp.h there leads to an include loop, so
don't change cpu-info.h.
Robert P. J. Day [Tue, 23 Jun 2009 19:37:06 +0000 (12:37 -0700)]
h8/300: fix incorrect "select" directives in arch/h8300/Kconfig.cpu.
Fix the incorrect "select" directives by dropping the "CONFIG_"
prefixes, and correcting the typo "H8S2768" to "H8S2678".
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dimitri Sivanich [Tue, 23 Jun 2009 19:37:04 +0000 (12:37 -0700)]
mm: fix handling of pagesets for downed cpus
After downing/upping a cpu, an attempt to set
/proc/sys/vm/percpu_pagelist_fraction results in an oops in
percpu_pagelist_fraction_sysctl_handler().
If a processor is downed then we need to set the pageset pointer back to
the boot pageset.
Updates of the high water marks should not access pagesets of unpopulated
zones (those pointer go to the boot pagesets which would be no longer
functional if their size would be increased beyond zero).
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com> Signed-off-by: Christoph Lameter <cl@linux-foundation.org> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Mel Gorman <mel@csn.ul.ie> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Tue, 23 Jun 2009 19:37:01 +0000 (12:37 -0700)]
rmap: fixup page_referenced() for nommu systems
After the recent changes that went into mm/vmscan.c to overhaul stuff, we
ended up with these warnings on no-mmu systems:
mm/vmscan.c: In function `shrink_page_list':
mm/vmscan.c:580: warning: unused variable `vm_flags'
mm/vmscan.c: In function `shrink_active_list':
mm/vmscan.c:1294: warning: `vm_flags' may be used uninitialized in this function
mm/vmscan.c:1242: note: `vm_flags' was declared here
This is because the no-mmu function defines page_referenced() to work on
the first argument only (the page). It does not clear the vm_flags given
to it because for no-mmu systems, they never actually get utilized. Since
that is no longer strictly true, we need to set vm_flags to 0 like
everyone else so gcc can do proper dead code elimination without annoying
us with unused warnings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: David Howells <dhowells@redhat.com> Acked-by: David McCullough <davidm@snapgear.com> Cc: Greg Ungerer <gerg@uclinux.org> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Tue, 23 Jun 2009 19:36:58 +0000 (12:36 -0700)]
mm: pass mm to grab_swap_token
If a kthread happens to use get_user_pages() on an mm (as KSM does),
there's a chance that it will end up trying to read in a swap page, then
oops in grab_swap_token() because the kthread has no mm: GUP passes down
the right mm, so grab_swap_token() ought to be using it.
We have not identified a stronger case than KSM's daemon (not yet in
mainline), but the issue must have come up before, since RHEL has included
a fix for this for years (though a different fix, they just back out of
grab_swap_token if current->mm is unset: which is what we first proposed,
but using the right mm here seems more correct).
Reported-by: Izik Eidus <ieidus@redhat.com> Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk> Acked-by: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix up HAVE_PERF_COUNTERS typo.
sh: Fix up more dma-mapping fallout.
sh: SH7786 SMP support.
sh: Wire up the uncached fixmap on sh64 as well.
sh: Use local TLB flush in set_pte_phys().
sh: Provide cpu_idle_wait() to fix up cpuidle/SMP build.
Linus Torvalds [Tue, 23 Jun 2009 18:36:01 +0000 (11:36 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA: Add __init/__exit macros to addr.c and cma.c
IB/ehca: Bump version number
mlx4_core: Fix dma_sync_single_for_cpu() with matching for_device() calls
IB/mthca: Replace dma_sync_single() use with proper functions
RDMA/nes: Fix FIN state handling under error conditions
RDMA/nes: Fix max_qp_init_rd_atom returned from query device
IB/ehca: Ensure that guid_entry index is not negative
IB/ehca: Tolerate dynamic memory operations before driver load
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (38 commits)
fusion: mptsas, fix lock imbalance
[SCSI] scsi_transport_fc: replace BUS_ID_SIZE by fixed count
sd, sr: fix Driver 'sd' needs updating message
scsi_transport_iscsi: return -EOVERFLOW for Too many iscsi targets
fc_transport: Selective return value from BSG timeout function
fc_transport: The softirq_done function registration for BSG request
sym53c8xx: ratelimit parity errors
explain the hidden scsi_wait_scan Kconfig variable
ibmvfc: Fix endless PRLI loop in discovery
ibmvfc: Process async events before command responses
libfc: Add runtime debugging with debug_logging module parameter
libfcoe: Add runtime debugging with module param debug_logging
fcoe: Add runtime debug logging with module parameter debug_logging
scsi_debug: Add support for physical block exponent and alignment
cnic: add NETDEV_1000 and NETDEVICES to Kconfig select
cnic: Fix __symbol_get() build error.
Revert "[SCSI] cnic: fix error: implicit declaration of function ‘__symbol_get’"
ipr: differentiate pci-x and pci-e based adapters
ipr: add test for MSI interrupt support
scsi_transport_spi: Blacklist Ultrium-3 tape for IU transfers
...
Linus Torvalds [Tue, 23 Jun 2009 18:34:24 +0000 (11:34 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: add dummy pgprot_noncached()
lib/checksum.c: fix endianess bug
asm-generic: hook up new system calls
asm-generic: list Arnd as asm-generic maintainer
asm-generic: drop HARDIRQ_BITS definition from hardirq.h
asm-generic: uaccess: fix up local access_ok() usage
asm-generic: uaccess: add missing access_ok() check to strnlen_user()
Hugh Dickins [Tue, 23 Jun 2009 12:52:49 +0000 (13:52 +0100)]
mm: don't rely on flags coincidence
Indeed FOLL_WRITE matches FAULT_FLAG_WRITE, matches GUP_FLAGS_WRITE,
and it's tempting to devise a set of Grand Unified Paging flags;
but not today. So until then, let's rely upon the compiler to spot
the coincidence, "rather than have that subtle dependency and a
comment for it" - as you remarked in another context yesterday.
Hugh Dickins [Tue, 23 Jun 2009 12:49:05 +0000 (13:49 +0100)]
hugetlb: fault flags instead of write_access
handle_mm_fault() is now passing fault flags rather than write_access
down to hugetlb_fault(), so better recognize that in hugetlb_fault(),
and in hugetlb_no_page().
Linus Torvalds [Tue, 23 Jun 2009 17:45:39 +0000 (10:45 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Make jack-plug notification selectable
ALSA: ctxfi - Add PM support
sound: seq_midi_event: fix decoding of (N)RPN events
ALSA: hda - Add digital-mic support to ALC262 auto model
ALSA: hda - Fix check of input source type for realtek codecs
ALSA: hda - Add quirk for Sony VAIO Z21MN
ALSA: hda - Get back Input Source for ALC262 toshiba-s06 model
ALSA: hda - Fix unsigned comparison in patch_sigmatel.c
ALSA: via82xx: add option to disable 500ms delay in snd_via82xx_codec_wait
sound: fix check for return value in snd_pcm_hw_refine
ALSA: ctxfi - Allow unknown PCI SSIDs
ASoC: Blackfin: update the bf5xx_i2s_resume parameters
ASoC: Blackfin: keep better track of SPORT configuration state
Linus Torvalds [Tue, 23 Jun 2009 17:40:19 +0000 (10:40 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (62 commits)
V4L/DVB (12131): BUGFIX: An incorrect Carrier Recovery Loop optimization table was being
V4L/DVB (12130): Fix a redundant compiler warning
V4L/DVB (12003): v4l2: Move bounding code outside I2C ifdef block
V4L/DVB (11913): cx231xx: TRY_FMT should not actually set anything
V4L/DVB (11912): em28xx: Use v4l bounding/alignment function
V4L/DVB (11911): cx231xx: Use v4l bounding/alignment function
V4L/DVB (11910): mt9: Use v4l bounding/alignment function
V4L/DVB (11909): cx23885: Use v4l bounding/alignment function
V4L/DVB (11908): w8968cf: Use v4l bounding/alignment function
V4L/DVB (11907): cx88: Use v4l bounding/alignment function
V4L/DVB (11906): saa7134: Use v4l bounding/alignment function
V4L/DVB (11905): vivi: Use v4l bounding/alignment function
V4L/DVB (11904): zoran: Use v4l bounding/alignment functiob
V4L/DVB (11903): sh_mobile_ceu_camera: Use v4l bounding/alignment function
V4L/DVB (11902): pxa-camera: Use v4l bounding/alignment function
V4L/DVB (11901): v4l2: Create helper function for bounding and aligning images
V4L/DVB (12128): v4l2: update framework documentation.
V4L/DVB (12125): v4l2: add new s_config subdev ops and v4l2_i2c_new_subdev_cfg/board calls
V4L/DVB (12122): pvrusb2: De-obfuscate code which handles routing schemes
V4L/DVB (12121): pvrusb2: Improve handling of routing schemes
...
Linus Torvalds [Tue, 23 Jun 2009 17:39:36 +0000 (10:39 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: don't set IORDY for reset
sata_fsl: Add power mgmt support
[libata] PATA driver for CF interface on AT91SAM9260 SoC
[libata] beautify module parameters
Paul Mundt [Tue, 23 Jun 2009 16:41:05 +0000 (01:41 +0900)]
sh: Fix up HAVE_PERF_COUNTERS typo.
That's HAVE_PERF_COUNTERS not HAVE_PERF_COUNTER. This was right
initially but I seem to have screwed it up while re-typing it out
by hand on another machine when I checked it in. Hmph.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Catalin Marinas [Tue, 23 Jun 2009 13:40:27 +0000 (14:40 +0100)]
kmemleak: Do not force the slab debugging Kconfig options
Selecting DEBUG_SLAB or SLUB_DEBUG by the KMEMLEAK menu entry may cause
issues with other dependencies (KMEMCHECK). These configuration options
aren't strictly needed by kmemleak but they may increase the chances of
finding leaks. This patch also updates the KMEMLEAK config entry help
text.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Paul Mundt [Tue, 23 Jun 2009 11:51:19 +0000 (13:51 +0200)]
asm-generic: add dummy pgprot_noncached()
Most architectures now provide a pgprot_noncached(), the
remaining ones can simply use an dummy default implementation,
except for cris and xtensa, which should override the
default appropriately.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Chris Zankel <chris@zankel.net> Cc: Magnus Damm <magnus.damm@gmail.com>
Paul Mundt [Fri, 19 Jun 2009 07:00:00 +0000 (16:00 +0900)]
sh: SH7786 SMP support.
SH7786 is roughly identical to SH-X3 proto SMP, though there are only 2
CPUs. This just wraps in to the existing SH-X3 SMP code with some minor
changes for SH7786, including wiring up the IPIs properly, enabling
IRQ_PER_CPU, and so forth.
Paul Mundt [Fri, 19 Jun 2009 06:37:11 +0000 (15:37 +0900)]
sh: Use local TLB flush in set_pte_phys().
set_pte_phys() presently uses the global flush_tlb_one(), which locks on
SMP trying to do the IPI. As we have not even initialized the other CPUs
at this point, switch to the local_ variant so the flush happens on the
boot CPU.
Change the wdt_pci.c watchdog driver so that the code is the same for
both the PCI-WDT500 as the PCI-WDT501 card. The selection of the card
is now being done via the module parameter: 'type' instead of the
config option CONFIG_WDT_501_PCI.
Manu Abraham [Thu, 18 Jun 2009 07:50:53 +0000 (04:50 -0300)]
V4L/DVB (12131): BUGFIX: An incorrect Carrier Recovery Loop optimization table was being
loaded for a given chip version. This would cause the optimization in
tuning not to be applied and thus a failed expectation, in tuning speed
increment. The patch swaps the tables in use. It also fixes a possible
one in a million condition where state->dev_ver implies an older Cut
(Cut < 2.0, eventhough the driver doesn't attach to any Cut older than
2.0) or even negative (due to a bad I2C bus master driver) for the card
combination.
Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing
out the issue at large.
Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manu Abraham [Wed, 17 Jun 2009 19:48:17 +0000 (16:48 -0300)]
V4L/DVB (12130): Fix a redundant compiler warning
drivers/media/dvb/frontends/stv090x.c: In function ‘stv090x_optimize_carloop_short’:
drivers/media/dvb/frontends/stv090x.c:2677: warning: ‘short_crl’ may be used uninitialized in this function
Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Fri, 12 Jun 2009, Randy Dunlap wrote:
> From: Randy Dunlap <randy.dunlap@oracle.com>
>
> Move v4l_bound_align_image() outside of an #ifdef CONFIG_I2C block
> so that it is always built. Fixes a build error:
clamp_align() should be moved as well, since it's only used by
v4l_bound_align_image(). I'm attaching an alternate version that fixes
this. Labeled the endif too.
Trent Piepho [Sun, 31 May 2009 00:45:46 +0000 (21:45 -0300)]
V4L/DVB (11913): cx231xx: TRY_FMT should not actually set anything
In the TRY_FMT handler the function get_scale() is called to find what the
scaler hardware will produce for a requested size.
The problem is that get_scale(struct cx231xx *dev, ..., unsigned int *vscale,
unsigned int *hscale) saves the calculated scale values into both the
pointer arguments and into dev's hscale and vscale fields. TRY_FMT shouldn't
actually change anything in the device state.
The code to in get_scale() that writes to dev->[hv]scale can just be
deleted. In all cases when dev's fields should be modified, get_scale()
was called with get_scale(dev, ..., &dev->hscale, &dev->vscale), so dev was
getting updated anyway.
This didn't actually cause a problem because nothing ever actually made use
of the hscale and vscale fields. I changed cx231xx_resolution_set() to use
those fields rather than re-calculate them with a call to get_scale().
Updating [hv]scale in cx231xx_resolution_set() isn't necessary because
every call of cx231xx_resolution_set() was already preceded by a call to
get_scale() or setting the [hv]scale fields, so they will be always be
up-to-date w.r.t. width and height.
Removing the call to get_scale() from cx231xx_resolution_set() allowed
making get_scale() a static function, which is a good thing for something
with such a short name. There is already another function with the same
name in the em28xx driver, but that one is static.
Trent Piepho [Sun, 31 May 2009 00:45:46 +0000 (21:45 -0300)]
V4L/DVB (11912): em28xx: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.
It appears that the em2800 can only scale by 50% or 100%, i.e. the only
heights supported might be 240 and 480. In that case the old code would
set any height other than 240 to 480. Request 240 get 240, but request 239
and then you get 480. Change it to round to the nearest supported value.
Trent Piepho [Sun, 31 May 2009 00:45:46 +0000 (21:45 -0300)]
V4L/DVB (11908): w8968cf: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.
The existing code was casting pointers to u32 and to unsigned int into
pointers to u16. This could mess up if someone passed in an image size
greater than 65,535 and on big-endian platforms it won't work at all.
The existing bounding code would shrink an image if it was too big, but
returned ERANGE if it was too small. The code will not shrink or expand as
necessary.
Trent Piepho [Sun, 31 May 2009 00:45:46 +0000 (21:45 -0300)]
V4L/DVB (11902): pxa-camera: Use v4l bounding/alignment function
The v4l function has a better algorithm for aligning image size.
For instance the old code would change 159x243 into 156x240 to meet the
alignment requirements. The new function will use 160x243, which is a lot
closer to what was asked for originally.
Trent Piepho [Sun, 31 May 2009 00:45:46 +0000 (21:45 -0300)]
V4L/DVB (11901): v4l2: Create helper function for bounding and aligning images
Most hardware has limits on minimum and maximum image dimensions and also
requirements about alignment. For example, image width must be even or a
multiple of four. Some hardware has requirements that the total image size
(width * height) be a multiple of some power of two.
v4l_bound_align_image() will enforce min and max width and height, power of
two alignment on width and height, and power of two alignment on total
image size.
It uses an efficient algorithm that will try to find the "closest" image
size that meets the requirements.
Hans Verkuil [Tue, 9 Jun 2009 20:12:33 +0000 (17:12 -0300)]
V4L/DVB (12125): v4l2: add new s_config subdev ops and v4l2_i2c_new_subdev_cfg/board calls
Add a new s_config core ops call: this is called with the irq and platform
data to be used to initialize the subdev.
Added new v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev_board calls
that allows you to pass these new arguments.
The existing v4l2_i2c_new_subdev functions were modified to also call
s_config.
In the future the existing v4l2_i2c_new_subdev functions will be replaced
by a single v4l2_i2c_new_subdev function similar to v4l2_i2c_new_subdev_cfg
but without the irq and platform_data arguments.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 20 Jun 2009 17:57:24 +0000 (14:57 -0300)]
V4L/DVB (12122): pvrusb2: De-obfuscate code which handles routing schemes
This change does not change any outward behavior; it merely chops down
some large if-conditions with embedded assignments into something a
little more maintainable for others (I of course never had a problem
with this...).
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 20 Jun 2009 17:55:31 +0000 (14:55 -0300)]
V4L/DVB (12121): pvrusb2: Improve handling of routing schemes
The pvrusb2 driver has a concept of "routing scheme" which defines
which physical inputs should be connected based on application's
choice of logical input. The correct "routing scheme" depends on the
specific device since different devices might wire up their muxes
Mike Isely [Sat, 20 Jun 2009 17:51:29 +0000 (14:51 -0300)]
V4L/DVB (12120): pvrusb2: Change initial default frequency setting
Change default frequency to be US Broadcast channel 3 - with the
transition to d igital the previous value has now become useless.
This change is PURELY to help with my testing (I need to set some kind
of default so it might as well be some thing usable).
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 20 Jun 2009 17:50:14 +0000 (14:50 -0300)]
V4L/DVB (12119): pvrusb2: Re-fix hardware scaling on video standard change
The cx25840 module's VBI initialization logic uses the current video
standard as part of its internal algorithm. This therefore means that
we probably need to make sure that the correct video standard has been
set before initializing VBI. (Normally we would not care about VBI,
but as described in an earlier changeset, VBI must be initialized
correctly on the cx25840 in order for the chip's hardware scaler to
operate correctly.)
It's kind of messy to force the video standard to be set before
initializing VBI (mainly because we can't know what the app really
wants that early in the initialization process). So this patch does
the next best thing: VBI is re-initialized after any point where the
video standard has been set.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 20 Jun 2009 17:45:52 +0000 (14:45 -0300)]
V4L/DVB (12118): pvrusb2: Fix hardware scaling when used with cx25840
The cx25840 module requires that its VBI initialization entry point be
called in order for hardware-scaled video capture to work properly -
even if we don't care about VBI. Making this behavior even more
subtle is that if the capture resolution is set to 720x480 - which is
the default that the pvrusb2 driver sets up - then the cx25840
bypasses the hardware scaler. Therefore this problem does not
manifest itself until some other resolution, e.g. 640x480, is tried.
MythTV typically defaults to 640x480 or 480x480, which means that
things break whenever the driver is used with MythTV.
This all has been known for a while (since at least Nov 2006), but
recent changes in the pvrusb2 driver (specifically in regards to
sub-device support) caused this to break again. VBI initialization
must happen *after* the chip's firmware is loaded, not before. With
this fix, 24xxx devices work correctly again.
A related fix that is part of this changeset is that now we
re-initialize VBI any time after we issue a reset to the cx25840
driver. Issuing a chip reset erases the state that the VBI setup
previously did. Until the HVR-1950 came along this subtlety went
unnoticed, because the pvrusb2 driver previously never issued such a
reset. But with the HVR-1950 we have to do that reset in order to
correctly transition from digital back to analog mode - and since the
HVR-1950 always starts in digital mode (required for the DVB side to
initialize correctly) then this device has never had a chance to work
correctly in analog mode! Analog capture on the HVR-1950 has been
broken this *ENTIRE* time. I had missed it until now because I've
usually been testing at the default 720x480 resolution which does not
require scaling... What fun. By re-initializing VBI after a cx25840
chip reset, correct behavior is restored.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Thu, 21 May 2009 15:49:28 +0000 (12:49 -0300)]
V4L/DVB (12116): cx23885: ensure correct IF freq is used on HVR1200 & HVR1700
Ensure that we're programming the tda18271 tuner with the correct
IF frequencies to match the programming of the TDA10048 DVB-T demod
for the HVR1200 and HVR1700 products.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tcm825x_remove is not necessarily called on module exit, it can also be
called when the i2c_adapter is removed. While the i2c adapter might never
be removed on an embedded system, in practice this sensor driver can also
be used in e.g. a USB webcam where this is a perfectly acceptable thing
to do.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 14 Jun 2009 09:47:35 +0000 (06:47 -0300)]
V4L/DVB (12107): smscoreapi: fix compile warning
gcc 4.3.1 generates this warning:
v4l/smscoreapi.c: In function 'smscore_gpio_configure':
v4l/smscoreapi.c:1481: warning: 'GroupNum' may be used uninitialized in this function
v4l/smscoreapi.c:1480: warning: 'TranslatedPinNum' may be used uninitialized in this function
While in practice this will not happen, it is something that the compiler
can't determine. Initializing these two local variables to 0 suppresses
this warning.
Hans Verkuil [Sun, 14 Jun 2009 08:20:21 +0000 (05:20 -0300)]
V4L/DVB (12104): ivtv/cx18: fix regression: class controls are no longer seen
A previous change (v4l2-common: remove v4l2_ctrl_query_fill_std) broke
the handling of class controls in VIDIOC_QUERYCTRL. The MPEG class control
was broken for all drivers that use the cx2341x module and the USER class
control was broken for ivtv and cx18.
This change adds back proper class control support.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (12101): em28xx: add support for EVGA inDtube
Add support for the EVGA inDtube. Both ATSC and analog side validated as
fully functional.
Thanks to Jake Crimmins from EVGA for providing the correct GPIO info.
Thanks to Alan Hagge for doing all the device testing.
Thanks to Greg Williamson for providing hardware for testing.
V4L/DVB (12100): em28xx: make sure the analog GPIOs are set if we used a card hint
In cases where the board had a default USB ID, we would not indentify the
board until after the call to em28xx_set_mode(). As a result, for those
boards the analog GPIOs were not being set before probing the i2c bus for
devices (the probe would occur with the GPIOs being all high).
Make a call to em28xx_set_mode() so that the GPIOs are set properly before
probing the i2c bus for devices.
This problem was detected with the EVGA inDtube, where the tvp5150 is not
powered on unless GPIO1 is pulled low.
Hans de Goede [Thu, 18 Jun 2009 17:29:20 +0000 (14:29 -0300)]
V4L/DVB (12092): gspca_sonixj + ov7630: invert vflip control instead of changing default
gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise
the picture is upside down. It is better to instead invert the meaning
of the control in the set function, and have the default be no vflip,
as one would expect vflip enabled to be upside down.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 17 Jun 2009 21:50:10 +0000 (18:50 -0300)]
V4L/DVB (12084): ov511: mark as deprecated
Mark the v4l1 ov511 as deprecated as we now have ov511 support in
the gspca ov519 driver. Note we should really also keep track of this
in Documentation/feature-removal-schedule.txt, but that is not
part of the v4l-dvb tree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 17 Jun 2009 21:41:01 +0000 (18:41 -0300)]
V4L/DVB (12083): ov511: remove ov518 usb id's from the driver
ov511: remove ov518 usb id's from the driver, as they have not been working
ever since the decompression code got removed from the kernel, and they
are no supported by the gspca_ov519 module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 17 Jun 2009 21:37:57 +0000 (18:37 -0300)]
V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor
Add support for st6422 bridge and sensor to the stv06xx gspca sub driver,
tested with:
Logitech QuickCam Messenger 046d:08f0 ST6422 integrated
Logitech QuickCam Mess. Plus 046d:08f6 ST6422 integrated
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Sun, 14 Jun 2009 09:32:52 +0000 (06:32 -0300)]
V4L/DVB (12078): gspca_ov519: Better default contrast for ov6630
Hmm, another one with an extra if (life sucks) the
default contrast really is no good for the ov6630, it
isn't even high enough in full daylight, this gives
the ov6630 a different initial value for a better out
of the box experience.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Sun, 14 Jun 2009 09:26:49 +0000 (06:26 -0300)]
V4L/DVB (12077): gspca_ov519: Fix 320x240 with ov7660 sensor
As reported on the ov51x-jpeg list, and as I can confirm with my own cam
the ov7670 in 320x240 has a number of broken columns of pixels
at the left of the picture. This was not present in the old
driver as it always used 640x480 and did software
downscaling (took me a while to figure that one out).
The fix adds a sensor specific if in so far sensor
neutral code :( But this is the only way to fix this,
this cannot be fixed by only changing sensor registers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>