powerpc: Minor cleanups of kernel virt address space definitions
Make FIXADDR_TOP a compile time constant and cleanup a
couple of definitions relative to the layout of the kernel
address space on ppc32. We also print out that layout at
boot time for debugging purposes.
This is a pre-requisite for properly fixing non-coherent
DMA allocactions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While it was a good idea to try to use the mm/vmalloc.c allocator instead
of our own (in fact, ours is itself a dup on an old variant of the vmalloc
one), unfortunately, the approach is terminally busted since
dma_alloc_coherent() can be called at interrupt time or in atomic contexts
and there's little chances we'll make the code in mm/vmalloc.c cope with\ that :-(
Until we can get the generic code to forbid that idiocy and fix all
drivers abusing it, we pretty much have no choice but revert to
our custom virtual space allocator.
There's also a problem with SMP safety since freeing such mapping
would require an IPI which cannot be done at interrupt time.
However, right now, I don't think we support any platform that is
both SMP and has non-coherent DMA (don't laugh, I know such things
do exist !) so we can sort that out later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Tue, 26 May 2009 22:06:12 +0000 (15:06 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: avoid back to back on_each_cpu in cpa_flush_array
x86, relocs: ignore R_386_NONE in kernel relocation entries
Linus Torvalds [Tue, 26 May 2009 21:48:36 +0000 (14:48 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Add support for VGA load detection (pre-945).
drm/i915: Use an I2C algo to do the flip to SDVO DDC bus.
drm/i915: Determine type before initialising connector
drm/i915: Return SDVO LVDS VBT mode if no EDID modes are detected.
drm/i915: Fetch SDVO LVDS mode lines from VBT, then reserve them
i915: support 8xx desktop cursors
drm/i915: allocate large pointer arrays with vmalloc
Linus Torvalds [Tue, 26 May 2009 19:15:35 +0000 (12:15 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFSv4: Fix the case where NFSv4 renewal fails
nfs: fix build error in nfsroot with initconst
XPRTRDMA: fix client rpcrdma FRMR registration on mlx4 devices
Linus Torvalds [Tue, 26 May 2009 19:14:46 +0000 (12:14 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Add missing check of pin vref 50 and others in Realtek codecs
ALSA: hda - Add 5stack-no-fp model for STAC927x
ALSA: hda - Add forced codec-slots for ASUS W5Fm
Linus Torvalds [Tue, 26 May 2009 19:13:33 +0000 (12:13 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: determine exact CPU frequency for HW Pstates
[CPUFREQ] powernow-k8 cleanup msg if BIOS does not export ACPI _PSS cpufreq data
[CPUFREQ] fix timer teardown in ondemand governor
[CPUFREQ] fix timer teardown in conservative governor
[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call
[CPUFREQ] powernow-k7 build fix when ACPI=n
[CPUFREQ] add atom family to p4-clockmod
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
r8169: avoid losing MSI interrupts
tcp: tcp_vegas ssthresh bugfix
mac8390: fix regression caused during net_device_ops conversion
gianfar: fix BUG under load after introduction of skb recycling
wimax/i2400m: usb: fix device reset on autosuspend while not yet idle
RxRPC: Error handling for rxrpc_alloc_connection()
ipv4: Fix oops with FIB_TRIE
pktgen: do not access flows[] beyond its length
gigaset: beyond ARRAY_SIZE of iwb->data
IPv6: set RTPROT_KERNEL to initial route
net: fix rtable leak in net/ipv4/route.c
net: fix length computation in rt_check_expire()
wireless: beyond ARRAY_SIZE of intf->crypto_stats
iwlwifi: update 5000 ucode support to version 2 of API
cfg80211: fix race between core hint and driver's custom apply
airo: fix airo_get_encode{,ext} buffer overflow like I mean it...
ath5k: fix interpolation with equal power levels
iwlwifi: do not cancel delayed work inside spin_lock_irqsave
ath5k: fix exp off-by-one when computing OFDM delta slope
wext: verify buffer size for SIOCSIWENCODEEXT
...
Trond Myklebust [Tue, 26 May 2009 18:51:00 +0000 (14:51 -0400)]
NFSv4: Fix the case where NFSv4 renewal fails
If the asynchronous lease renewal fails (usually due to a soft timeout),
then we _must_ schedule state recovery in order to ensure that we don't
lose the lease unnecessarily or, if the lease is already lost, that we
recover the locking state promptly...
But the missing const causes popwerpc to fail with latest
updates to __initconst like this:
fs/nfs/nfsroot.c:400: error: __setup_str_nfs_root_setup causes a section type conflict
fs/nfs/nfsroot.c:400: error: __setup_str_nfs_root_setup causes a section type conflict
The bug is only present with kbuild-next.
Following patch has been build tested.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Vu Pham [Tue, 26 May 2009 18:51:00 +0000 (14:51 -0400)]
XPRTRDMA: fix client rpcrdma FRMR registration on mlx4 devices
mlx4/connectX FRMR requires local write enable together with remote
rdma write enable. This fixes NFS/RDMA operation over the ConnectX
Infiniband HCA in the default memreg mode.
Signed-off-by: Vu Pham <vu@mellanox.com> Signed-off-by: Tom Talpey <tmtalpey@gmail.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Ma Ling [Tue, 26 May 2009 03:31:00 +0000 (11:31 +0800)]
drm/i915: Add support for VGA load detection (pre-945).
Two approaches for VGA detections: hot plug detection for 945G onwards
and load pipe detection for Pre-945G. Load pipe detection will get one free
pipe, set border color as red and blue, then check CRT status by
swf register. This is a sync-up with the 2D driver.
Signed-off-by: Ma Ling <ling.ma@intel.com> Signed-off-by: Eric Anholt <eric@anholt.net>
Solution is to determine the frequency directly from Pstate MSRs instead
of using rounded values from ACPI table.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Dave Jones <davej@redhat.com>
* Rafael J. Wysocki (rjw@sisk.pl) wrote:
> This message has been generated automatically as a part of a report
> of regressions introduced between 2.6.28 and 2.6.29.
>
> The following bug entry is on the current list of known regressions
> introduced between 2.6.28 and 2.6.29. Please verify if it still should
> be listed and let me know (either way).
>
>
> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=13186
> Subject : cpufreq timer teardown problem
> Submitter : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Date : 2009-04-23 14:00 (24 days old)
> References : http://marc.info/?l=linux-kernel&m=124049523515036&w=4
> Handled-By : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Patch : http://patchwork.kernel.org/patch/19754/
> http://patchwork.kernel.org/patch/19753/
>
(updated changelog)
cpufreq fix timer teardown in ondemand governor
The problem is that dbs_timer_exit() uses cancel_delayed_work() when it should
use cancel_delayed_work_sync(). cancel_delayed_work() does not wait for the
workqueue handler to exit.
The ondemand governor does not seem to be affected because the
"if (!dbs_info->enable)" check at the beginning of the workqueue handler returns
immediately without rescheduling the work. The conservative governor in
2.6.30-rc has the same check as the ondemand governor, which makes things
usually run smoothly. However, if the governor is quickly stopped and then
started, this could lead to the following race :
dbs_enable could be reenabled and multiple do_dbs_timer handlers would run.
This is why a synchronized teardown is required.
The following patch applies to, at least, 2.6.28.x, 2.6.29.1, 2.6.30-rc2.
Depends on patch
cpufreq: remove rwsem lock from CPUFREQ_GOV_STOP call
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> CC: Andrew Morton <akpm@linux-foundation.org> CC: gregkh@suse.de CC: stable@kernel.org CC: cpufreq@vger.kernel.org CC: Ingo Molnar <mingo@elte.hu> CC: rjw@sisk.pl CC: Ben Slusky <sluskyb@paranoiacs.org> Signed-off-by: Dave Jones <davej@redhat.com>
[CPUFREQ] fix timer teardown in conservative governor
* Rafael J. Wysocki (rjw@sisk.pl) wrote:
> This message has been generated automatically as a part of a report
> of regressions introduced between 2.6.28 and 2.6.29.
>
> The following bug entry is on the current list of known regressions
> introduced between 2.6.28 and 2.6.29. Please verify if it still should
> be listed and let me know (either way).
>
>
> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=13186
> Subject : cpufreq timer teardown problem
> Submitter : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Date : 2009-04-23 14:00 (24 days old)
> References : http://marc.info/?l=linux-kernel&m=124049523515036&w=4
> Handled-By : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Patch : http://patchwork.kernel.org/patch/19754/
> http://patchwork.kernel.org/patch/19753/
>
(re-send with updated changelog)
cpufreq fix timer teardown in conservative governor
The problem is that dbs_timer_exit() uses cancel_delayed_work() when it should
use cancel_delayed_work_sync(). cancel_delayed_work() does not wait for the
workqueue handler to exit.
The ondemand governor does not seem to be affected because the
"if (!dbs_info->enable)" check at the beginning of the workqueue handler returns
immediately without rescheduling the work. The conservative governor in
2.6.30-rc has the same check as the ondemand governor, which makes things
usually run smoothly. However, if the governor is quickly stopped and then
started, this could lead to the following race :
dbs_enable could be reenabled and multiple do_dbs_timer handlers would run.
This is why a synchronized teardown is required.
Depends on patch
cpufreq: remove rwsem lock from CPUFREQ_GOV_STOP call
The following patch applies to 2.6.30-rc2. Stable kernels have a similar
issue which should also be fixed, but the code changed between 2.6.29
and 2.6.30, so this patch only applies to 2.6.30-rc.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> CC: Andrew Morton <akpm@linux-foundation.org> CC: gregkh@suse.de CC: stable@kernel.org CC: cpufreq@vger.kernel.org CC: Ingo Molnar <mingo@elte.hu> CC: rjw@sisk.pl CC: Ben Slusky <sluskyb@paranoiacs.org> Signed-off-by: Dave Jones <davej@redhat.com>
[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call
* Rafael J. Wysocki (rjw@sisk.pl) wrote:
> This message has been generated automatically as a part of a report
> of regressions introduced between 2.6.28 and 2.6.29.
>
> The following bug entry is on the current list of known regressions
> introduced between 2.6.28 and 2.6.29. Please verify if it still should
> be listed and let me know (either way).
>
>
> Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=13186
> Subject : cpufreq timer teardown problem
> Submitter : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Date : 2009-04-23 14:00 (24 days old)
> References : http://marc.info/?l=linux-kernel&m=124049523515036&w=4
> Handled-By : Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
> Patch : http://patchwork.kernel.org/patch/19754/
> http://patchwork.kernel.org/patch/19753/
The patches linked above depend on the following patch to remove
circular locking dependency :
cpufreq: remove rwsem lock from CPUFREQ_GOV_STOP call
(the following issue was faced when using cancel_delayed_work_sync() in the
timer teardown (which fixes a race).
* KOSAKI Motohiro (kosaki.motohiro@jp.fujitsu.com) wrote:
> Hi
>
> my box output following warnings.
> it seems regression by commit 7ccc7608b836e58fbacf65ee4f8eefa288e86fac.
>
> A: work -> do_dbs_timer() -> cpu_policy_rwsem
> B: store() -> cpu_policy_rwsem -> cpufreq_governor_dbs() -> work
>
>
Hrm, I think it must be due to my attempt to fix the timer teardown race
in ondemand governor mixed with new locking behavior in 2.6.30-rc.
The rwlock seems to be taken around the whole call to
cpufreq_governor_dbs(), when it should be only taken around accesses to
the locked data, and especially *not* around the call to
dbs_timer_exit().
Reverting my fix attempt would put the teardown race back in place
(replacing the cancel_delayed_work_sync by cancel_delayed_work).
Instead, a proper fix would imply modifying this critical section :
cpufreq.c: __cpufreq_remove_dev()
...
if (cpufreq_driver->target)
__cpufreq_governor(data, CPUFREQ_GOV_STOP);
unlock_policy_rwsem_write(cpu);
To make sure the __cpufreq_governor() callback is not called with rwsem
held. This would allow execution of cancel_delayed_work_sync() without
being nested within the rwsem.
Applies on top of the 2.6.30-rc5 tree.
Required to remove circular dep in teardown of both conservative and
ondemande governors so they can use cancel_delayed_work_sync().
CPUFREQ_GOV_STOP does not modify the policy, therefore this locking seemed
unneeded.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> CC: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Greg KH <greg@kroah.com> CC: Ingo Molnar <mingo@elte.hu> CC: "Rafael J. Wysocki" <rjw@sisk.pl> CC: Ben Slusky <sluskyb@paranoiacs.org> CC: Chris Wright <chrisw@sous-sol.org> CC: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dave Jones <davej@redhat.com>
Jarod Wilson [Fri, 6 Mar 2009 20:24:57 +0000 (20:24 +0000)]
[CPUFREQ] add atom family to p4-clockmod
Some atom procs don't do freq scaling (such as the atom 330 on my own
littlefalls2 board). By adding the atom family here, we at least get
the benefit of passive cooling in a thermal emergency. Not sure how
to see that its actually helping any, but the driver does bind and
claim its functioning on my atom 330.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Dave Jones <davej@redhat.com>
David Dillow [Fri, 22 May 2009 15:29:34 +0000 (15:29 +0000)]
r8169: avoid losing MSI interrupts
The 8169 chip only generates MSI interrupts when all enabled event
sources are quiescent and one or more sources transition to active. If
not all of the active events are acknowledged, or a new event becomes
active while the existing ones are cleared in the handler, we will not
see a new interrupt.
The current interrupt handler masks off the Rx and Tx events once the
NAPI handler has been scheduled, which opens a race window in which we
can get another Rx or Tx event and never ACK'ing it, stopping all
activity until the link is reset (ifconfig down/up). Fix this by always
ACK'ing all event sources, and loop in the handler until we have all
sources quiescent.
Signed-off-by: David Dillow <dave@thedillows.org> Tested-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Tejun Heo [Tue, 26 May 2009 05:42:40 +0000 (14:42 +0900)]
x86, relocs: ignore R_386_NONE in kernel relocation entries
For relocatable 32bit kernels, boot/compressed/relocs.c processes
relocation entries in the kernel image and appends it to the kernel
image such that boot/compressed/head_32.S can relocate the kernel.
The kernel image is one statically linked object and only uses two
relocation types - R_386_PC32 and R_386_32, of the two only the latter
needs massaging during kernel relocation and thus handled by relocs.
R_386_PC32 is ignored and all other relocation types are considered
error.
When the target of a relocation resides in a discarded section,
binutils doesn't throw away the relocation record but nullifies it by
changing it to R_386_NONE, which unfortunately makes relocs fail.
The problem was triggered by yet out-of-tree x86 stack unwind patches
but given the binutils behavior, ignoring R_386_NONE is the right
thing to do.
The problem has been tracked down to binutils behavior by Jan Beulich.
[ Impact: fix build with certain binutils by ignoring R_386_NONE ]
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jan Beulich <JBeulich@novell.com> Cc: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <4A1B8150.40702@kernel.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Finn Thain [Tue, 26 May 2009 05:43:49 +0000 (22:43 -0700)]
mac8390: fix regression caused during net_device_ops conversion
Changeset ca17584bf2ad1b1e37a5c0e4386728cc5fc9dabc ("mac8390: update
to net_device_ops") broke mac8390 by adding 8390.o to the link. That
meant that lib8390.c was included twice, once in mac8390.c and once in
8390.c, subject to different macros. This patch reverts that by
avoiding the wrappers in 8390.c. They seem to be of no value since
COMPAT_NET_DEV_OPS is going away soon.
Tested with a Kinetics EtherPort card.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Hideo Saito [Sun, 24 May 2009 15:33:34 +0000 (15:33 +0000)]
powerpc/mm: Fix broken MMU PID stealing on !SMP
The recent rework of the MMU PID handling for non-hash CPUs has a
subtle bug in the !SMP "optimized" variant of the PID stealing
function. It clears the PID in the mm context before it calls
local_flush_tlb_mm(). However, the later will not flush anything
if the PID in the context is clear...
Signed-off-by: Hideo Saito <hsaito.ppc@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
NeilBrown [Tue, 26 May 2009 02:57:21 +0000 (12:57 +1000)]
md: don't update curr_resync_completed without also updating reshape_position.
In order for the metadata to always be consistent, we mustn't updated
curr_resync_completed without also updating reshape_position.
The reshape code updates both at the same time. However since
commit 97e4f42d62badb0f9fbc27c013e89bc1336a03bc
the common md_do_sync will sometimes update curr_resync_completed
but is not in a position to update reshape_position.
So if MD_RECOVERY_RESHAPE is set (indicating that a reshape is
happening, so reshape_position might change), don't update
curr_resync_completed in md_do_sync, leave it to the per-personality
reshape code.
NeilBrown [Mon, 25 May 2009 23:41:17 +0000 (09:41 +1000)]
md: bitmap: improve bitmap maintenance code.
The code for checking which bits in the bitmap can be cleared
has 2 problems:
1/ it repeatedly takes and drops a spinlock, where it would make
more sense to just hold on to it most of the time.
2/ it doesn't make use of some opportunities to skip large sections
of the bitmap
This patch fixes those. It will only affect CPU consumption, not
correctness.
NeilBrown [Mon, 25 May 2009 23:41:17 +0000 (09:41 +1000)]
md: improve errno return when setting array_size
Instead of always returns EINVAL if anything goes wrong
when setting the array size, add the option of
E2BIG
if the size requested is too large. This makes it easier
for user-space to be sure what went wrong.
We previously didn't update these fields when writing the metadata
because they could never change. They can now, so we better write
them.
v0.90 metadata always updated these fields.
Linus Torvalds [Mon, 25 May 2009 22:51:27 +0000 (15:51 -0700)]
Merge branch 'kvm-updates/2.6.30' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.30' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Fix PDPTR reloading on CR4 writes
KVM: Make paravirt tlb flush also reload the PAE PDPTRs
Linus Torvalds [Mon, 25 May 2009 22:50:32 +0000 (15:50 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Remove remap percpu allocator for the time being
x86: cpa_flush_array wbinvd should be done on all CPUs
x86: bugfix wbinvd() model check instead of family check
x86: introduce noxsave boot parameter
x86, setup: revert ACPI 3 E820 extended attributes support
x86: DMI match for the Sony VGN-Z540N as it needs BIOS reboot
Avi Kivity [Sun, 24 May 2009 19:19:00 +0000 (22:19 +0300)]
KVM: Fix PDPTR reloading on CR4 writes
The processor is documented to reload the PDPTRs while in PAE mode if any
of the CR4 bits PSE, PGE, or PAE change. Linux relies on this
behaviour when zapping the low mappings of PAE kernels during boot.
The code already handled changes to CR4.PAE; augment it to also notice changes
to PSE and PGE.
This triggered while booting an F11 PAE kernel; the futex initialization code
runs before any CR3 reloads and writes to a NULL pointer; the futex subsystem
ended up uninitialized, killing PI futexes and pulseaudio which uses them.
Cc: stable@kernel.org Signed-off-by: Avi Kivity <avi@redhat.com>
Avi Kivity [Sun, 24 May 2009 19:15:25 +0000 (22:15 +0300)]
KVM: Make paravirt tlb flush also reload the PAE PDPTRs
The paravirt tlb flush may be used not only to flush TLBs, but also
to reload the four page-directory-pointer-table entries, as it is used
as a replacement for reloading CR3. Change the code to do the entire
CR3 reloading dance instead of simply flushing the TLB.
Cc: stable@kernel.org Signed-off-by: Avi Kivity <avi@redhat.com>
gianfar: fix BUG under load after introduction of skb recycling
Since commit 0fd56bb5be6455d0d42241e65aed057244665e5e ("gianfar:
Add support for skb recycling"), gianfar puts skbuffs that are in
the rx ring back onto the recycle list as-is in case there was a
receive error, but this breaks the following invariant: that all
skbuffs on the recycle list have skb->data = skb->head + NET_SKB_PAD.
The RXBUF_ALIGNMENT realignment done in gfar_new_skb() will be done
twice on skbuffs recycled in this way, causing there not to be enough
room in the skb anymore to receive a full packet, eventually leading
to an skb_over_panic from gfar_clean_rx_ring() -> skb_put().
Resetting the skb->data pointer to skb->head + NET_SKB_PAD before
putting the skb back onto the recycle list restores the mentioned
invariant, and should fix this issue.
Reported-by: Michael Guntsche <mike@it-loops.com> Tested-by: Michael Guntsche <mike@it-loops.com> Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Mon, 25 May 2009 06:06:02 +0000 (08:06 +0200)]
ALSA: hda - Add missing check of pin vref 50 and others in Realtek codecs
Some Realtek codecs like ALC861 seem to support only VREF50 while the
current driver assumes it's only VREF80. Check other VREF bits to set
the correct value.
Tejun Heo [Mon, 25 May 2009 03:01:59 +0000 (12:01 +0900)]
x86: Remove remap percpu allocator for the time being
Remap percpu allocator has subtle bug when combined with page
attribute changing. Remap percpu allocator aliases PMD pages for the
first chunk and as pageattr doesn't know about the alias it ends up
updating page attributes of the original mapping thus leaving the
alises in inconsistent state which might lead to subtle data
corruption. Please read the following threads for more information:
http://thread.gmane.org/gmane.linux.kernel/835783
The following is the proposed fix which teaches pageattr about percpu
aliases.
http://thread.gmane.org/gmane.linux.kernel/837157
However, the above changes are deemed too pervasive for upstream
inclusion for 2.6.30 release, so this patch essentially disables
the remap allocator for the time being.
James Bottomley [Sun, 24 May 2009 20:03:43 +0000 (13:03 -0700)]
async: make sure independent async domains can't accidentally entangle
The problem occurs when async_synchronize_full_domain() is called when
the async_pending list is not empty. This will cause lowest_running()
to return the cookie of the first entry on the async_pending list, which
might be nothing at all to do with the domain being asked for and thus
cause the domain synchronization to wait for an unrelated domain. This
can cause a deadlock if domain synchronization is used from one domain
to wait for another.
Fix by running over the async_pending list to see if any pending items
actually belong to our domain (and return their cookies if they do).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PM: Do not hold dpm_list_mtx while disabling/enabling nonboot CPUs
We shouldn't hold dpm_list_mtx while executing
[disable|enable]_nonboot_cpus(), because theoretically this may lead
to a deadlock as shown by the following example (provided by Johannes
Berg):
CPU 3 CPU 2 CPU 1
suspend/hibernate
something:
rtnl_lock() device_pm_lock()
-> mutex_lock(&dpm_list_mtx)
mutex_lock(&dpm_list_mtx)
linkwatch_work
-> rtnl_lock()
disable_nonboot_cpus()
-> flush CPU 3 workqueue
Fortunately, device drivers are supposed to stop any activities that
might lead to the registration of new device objects way before
disable_nonboot_cpus() is called, so it shouldn't be necessary to
hold dpm_list_mtx over the entire late part of device suspend and
early part of device resume.
Thus, during the late suspend and the early resume of devices acquire
dpm_list_mtx only when dpm_list is going to be traversed and release
it right after that.
This patch is reported to fix the regressions tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=13245.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Miles Lane <miles.lane@gmail.com> Tested-by: Ming Lei <tom.leiming@gmail.com>
Takashi Iwai [Sun, 24 May 2009 17:00:08 +0000 (19:00 +0200)]
ALSA: hda - Add 5stack-no-fp model for STAC927x
The recent fix for the headphone volume control on IDT/STAC codecs
resulted in the removal of invalid "Side" volume eventually. But,
if the front panel doesn't exist, this setup could be regarded as a
sort of regression, as reported in kernel bug #13250.
Now as a workaround, a new model 5stack-no-fp is added so that the user
without the front panel can choose this one explicitly.
Steve French [Sat, 23 May 2009 18:57:25 +0000 (18:57 +0000)]
[CIFS] Avoid open on possible directories since Samba now rejects them
Small change (mostly formatting) to limit lookup based open calls to
file create only.
After discussion yesteday on samba-technical about the posix lookup
regression, and looking at a problem with cifs posix open to one
particular Samba version, Jeff and JRA realized that Samba server's
behavior changed in this area (posix open behavior on files vs.
directories). To make this behavior consistent, JRA just made a
fix to Samba server to alter how it handles open of directories (now
returning the equivalent of EISDIR instead of success). Since we don't
know at lookup time whether the inode is a directory or file (and
thus whether posix open will succeed with most current Samba server),
this change avoids the posix open code on lookup open (just issues
posix open on creates). This gets the semantic benefits we want
(atomicity, posix byte range locks, improved write semantics on newly
created files) and file create still is fast, and we avoid the problem
that Jeff noticed yesterday with "openat" (and some open directory
calls) of non-cached directories to one version of Samba server, and
will work with future Samba versions (which include the fix jra just
pushed into Samba server). I confirmed this approach with jra
yesterday and with Shirish today.
Posix open is only called (at lookup time) for file create now.
For opens (rather than creates), because we do not know if it
is a file or directory yet, and current Samba no longer allows
us to do posix open on dirs, we could end up wasting an open call
on what turns out to be a dir. For file opens, we wait to call posix
open till cifs_open. It could be added here (lookup) in the future
but the performance tradeoff of the extra network request when EISDIR
or EACCES is returned would have to be weighed against the 50%
reduction in network traffic in the other paths.
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com> Tested-by: Jeff Layton <jlayton@redhat.com> CC: Jeremy Allison <jra@samba.org> Signed-off-by: Steve French <sfrench@us.ibm.com>
Breno Leitao [Sat, 23 May 2009 00:30:39 +0000 (21:30 -0300)]
icom: fix rmmod crash
Actually the icom driver is crashing when is being removed because
the driver is kfreeing the adapter structure before calling
pci_release_regions(), which result in the following error:
Linus Torvalds [Fri, 22 May 2009 20:38:52 +0000 (13:38 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name
ALSA: hda - fix audio on HP TX25xx series notebooks
ALSA: pcsp - fix printk format warning again
x86: cpa_flush_array wbinvd should be done on all CPUs
cpa_flush_array seems to prefer wbinvd() over clflush at 4M threshold.
clflush needs to be done on only one CPU as per instruction definition.
wbinvd() however, should be done on all CPUs.
[ Impact: fix missing flush which could cause data corruption ]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
x86: bugfix wbinvd() model check instead of family check
wbinvd is supported on all CPUs 486 or later. But,
pageattr.c is checking x86_model >= 4 before wbinvd(), which looks like
an oversight bug. It was first introduced at one place by changeset d7c8f21a8cad0228c7c5ce2bb6dbd95d1ee49d13 and got copied over to second
place in the same file later.
[ Impact: fix missing cache flush on early-model CPUs, potential data corruption ]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Ma Ling [Mon, 18 May 2009 08:12:46 +0000 (16:12 +0800)]
drm/i915: Use an I2C algo to do the flip to SDVO DDC bus.
Previously, we would set the control bus switch before calls were made
to request EDID information over DDC. But recently the DDC code started
doing multiple I2C transfers to get the EDID extensions as well. This
tripped up SDVO, because the control bus switch is only in effect until
the next STOP after a START. By doing our own algo, we can wrap each i2c
transaction on the DDC I2C bus with the control bus switch it requires.
freedesktop.org bug #21042
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Hand application for conflict, fixed error path] Signed-off-by: Eric Anholt <eric@anholt.net>
Suresh Siddha [Fri, 22 May 2009 19:17:45 +0000 (12:17 -0700)]
x86: introduce noxsave boot parameter
Introduce "noxsave" boot parameter which will disable the cpu's xsave/xrstor
capabilities. Useful for debugging and working around xsave related issues.
[ Impact: make it possible to debug problems in the field ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Jonas Bonn [Fri, 15 May 2009 07:10:41 +0000 (09:10 +0200)]
drm/i915: Determine type before initialising connector
drm_connector_init sets both the connector type and the connector type_id
on the newly initialised connector. As the connector type_id is coupled to
the connector type, the connector type cannot simply be modified on an
initialised connector.
This patch changes the order of operations on intel_sdvo_init so that the
type is determined before the connector is intialised.
This fixes a bug whereby the name card0-VGA-1 would be allocted to both a
CRT and an SDVO connector since the SDVO connector would be initialised
with type 'unknown' and hence have its type_id assigned from the wrong pool.
Signed-off-by: Jonas Bonn <jonas@southpole.se> Signed-off-by: Eric Anholt <eric@anholt.net>
Jesse Barnes [Wed, 20 May 2009 20:47:08 +0000 (16:47 -0400)]
i915: support 8xx desktop cursors
For some reason we never added 8xx desktop cursor support to the
kernel. This patch fixes that.
[krh: Also set the size on pre-i915 hw.] Tested-by: Kristian Høgsberg <krh@redhat.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net>
H. Peter Anvin [Thu, 21 May 2009 18:46:16 +0000 (11:46 -0700)]
x86, setup: revert ACPI 3 E820 extended attributes support
Remove ACPI 3 E820 extended memory attributes support. At least one
vendor actively set all the flags to zero, but left ECX on return at
24. This bug may be present in other BIOSes.
The breakage functionally means the ACPI 3 flags are probably
completely useless, and that no OS any time soon is going to rely on
their existence. Therefore, drop support completely. We may want to
revisit this question in the future, if we find ourselves actually
needing the flags.
This reverts all or part of the following checkins:
However, retain the part from the latter commit that copies e820 into
a temporary buffer; that is an unrelated BIOS workaround. Put in a
comment to explain that part.
See https://bugzilla.redhat.com/show_bug.cgi?id=499396 for some
additional information.
[ Impact: detect all memory on affected machines ]
Reported-by: Thomas J. Baker <tjb@unh.edu> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Acked-by: Len Brown <len.brown@intel.com> Cc: Chuck Ebbert <cebbert@redhat.com> Cc: Kyle McMartin <kmcmartin@redhat.com> Cc: Matt Domsch <matt_domsch@dell.com>
Andreas Mohr [Fri, 22 May 2009 15:48:58 +0000 (17:48 +0200)]
ALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name
ALSA sound/core/control.c:232: Control name 'Sigmatel Surround Phase
Inversion Playback Switch' truncated to 'Sigmatel Surround Phase
Inversion Playback ' bootup message by omitting weird Sigmatel prefix
in this case; also fix up the related ca0106 mixer control removal
part by using identical naming there.
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Fri, 22 May 2009 14:37:42 +0000 (07:37 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: IP32: Remove unnecessary if not even harmful volatile keywords.
MIPS: IP32: Fix build error due to uninitialized variable.
MIPS: Fix sparse warning in incompatiable argument type of clear_user.
Linus Torvalds [Fri, 22 May 2009 14:33:38 +0000 (07:33 -0700)]
Merge branch 'sh/for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
video: stop sh_mobile_lcdcfb only if started
sh: ap325 camera without i2c driver fix
Corey Minyard [Wed, 20 May 2009 18:36:17 +0000 (13:36 -0500)]
ipmi: fix ipmi_si modprobe hang
Instead of queuing IPMB messages before channel initialization, just
throw them away. Nobody will be listening for them at this point,
anyway, and they will clog up the queue and nothing will be delivered
if we queue them.
Also set the current channel to the number of channels, as this value
is used to tell if the channel information has been initialized.
Signed-off-by: Corey Minyard <cminyard@mvista.com> Cc: Ferenc Wagner <wferi@niif.hu> Cc: Dan Frazier <dannf@hp.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances. Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.
It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.
v2:
Model detection fixup from Martin.
Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Ralf Baechle [Fri, 22 May 2009 09:48:17 +0000 (10:48 +0100)]
MIPS: IP32: Fix build error due to uninitialized variable.
CC arch/mips/sgi-ip32/ip32-reset.o
cc1: warnings being treated as errors
arch/mips/sgi-ip32/ip32-reset.c: In function 'debounce':
arch/mips/sgi-ip32/ip32-reset.c:97: error: 'reg_a' is used uninitialized in this function
The issues is old but due to the volatile keyword gcc older than 4.4 did
not warn about this obvious bug.
Wu Zhangjin [Wed, 20 May 2009 21:50:01 +0000 (05:50 +0800)]
MIPS: Fix sparse warning in incompatiable argument type of clear_user.
The type of the second argument of access_ok should be (void __user *).
The unnecessary conversion of the clear_user address argument was causing
sparse to emit warnings on the __chk_user_ptr check.
Ryusuke Konishi [Fri, 22 May 2009 11:36:21 +0000 (20:36 +0900)]
nilfs2: fix memory leak in nilfs_ioctl_clean_segments
This fixes a new memory leak problem in garbage collection. The
problem was brought by the bugfix patch ("nilfs2: fix lock order
reversal in nilfs_clean_segments ioctl").
Thanks to Kentaro Suzuki for finding this problem.
wimax/i2400m: usb: fix device reset on autosuspend while not yet idle
When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.
If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.
To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is rejected (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).
Magnus Damm [Wed, 20 May 2009 14:34:43 +0000 (14:34 +0000)]
video: stop sh_mobile_lcdcfb only if started
This patch fixes the LCDC driver to avoid calling the
function sh_mobile_lcdc_start_stop(priv, 0) unless the
same function has been called before to start the LCDC
hardware.
Triggered when sh_mobile_lcdcfb.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 20 May 2009 14:30:06 +0000 (14:30 +0000)]
sh: ap325 camera without i2c driver fix
This patch fixes the ap325rxa ncm03j camera code to handle
the case where no i2c driver is present. Without this fix
i2c_transfer() may be passed NULL as adapter which results
in a crash.
Triggered when i2c-sh_mobile.c failed to probe() due to
missing MSTP clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Steve French [Thu, 21 May 2009 22:21:53 +0000 (22:21 +0000)]
[CIFS] fix posix open regression
Posix open code was not properly adding the file to the
list of open files. Fix allocating cifsFileInfo
more than once, and adding twice to flist and tlist.
Also fix mode setting to be done in one place in these
paths.
Signed-off-by: Steve French <sfrench@us.ibm.com> Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com> Tested-by: Jeff Layton <jlayton@redhat.com> Tested-by: Luca Tettamanti <kronos.it@gmail.com>
Dan Carpenter [Thu, 21 May 2009 22:22:02 +0000 (15:22 -0700)]
RxRPC: Error handling for rxrpc_alloc_connection()
rxrpc_alloc_connection() doesn't return an error code on failure, it just
returns NULL. IS_ERR(NULL) is false.
Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Olsson [Thu, 21 May 2009 22:20:59 +0000 (15:20 -0700)]
ipv4: Fix oops with FIB_TRIE
It seems we can fix this by disabling preemption while we re-balance the
trie. This is with the CONFIG_CLASSIC_RCU. It's been stress-tested at high
loads continuesly taking a full BGP table up/down via iproute -batch.
Note. fib_trie is not updated for CONFIG_PREEMPT_RCU
Reported-by: Andrei Popa Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Thu, 21 May 2009 22:07:12 +0000 (15:07 -0700)]
pktgen: do not access flows[] beyond its length
typo -- pkt_dev->nflows is for stats only, the number of concurrent
flows is stored in cflows.
Reported-By: Vladimir Ivashchenko <hazard@francoudi.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The use of unspecified protocol in IPv6 initial route prevents quagga to
install IPv6 default route:
# show ipv6 route
S ::/0 [1/0] via fe80::1, eth1_0
K>* ::/0 is directly connected, lo, rej
C>* ::1/128 is directly connected, lo
C>* fe80::/64 is directly connected, eth1_0
# ip -6 route
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
ff00::/8 dev eth1_0 metric 256 mtu 1500 advmss 1440 hoplimit -1
unreachable default dev lo proto none metric -1 error -101 hoplimit 255
The attached patch ensures RTPROT_KERNEL to the default initial route
and fixes the problem for quagga.
This is similar to "ipv6: protocol for address routes" f410a1fba7afa79d2992620e874a343fdba28332.
# show ipv6 route
S>* ::/0 [1/0] via fe80::1, eth1_0
C>* ::1/128 is directly connected, lo
C>* fe80::/64 is directly connected, eth1_0
# ip -6 route
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
ff00::/8 dev eth1_0 metric 256 mtu 1500 advmss 1440 hoplimit -1
default via fe80::1 dev eth1_0 proto zebra metric 1024 mtu 1500
advmss 1440 hoplimit -1
unreachable default dev lo proto kernel metric -1 error -101 hoplimit 255
Signed-off-by: Jean-Mickael Guerin <jean-mickael.guerin@6wind.com> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>