Sage Weil [Fri, 14 May 2010 16:35:38 +0000 (09:35 -0700)]
ceph: invalidate affected dentry leases on aborted requests
If we abort a request, we return to caller, but the request may still
complete. And if we hold the dir FILE_EXCL bit, we may not release a
lease when sending a request. A simple un-tar, control-c, un-tar again
will reproduce the bug (manifested as a 'Cannot open: File exists').
Ensure we invalidate affected dentry leases (as well dir I_COMPLETE) so
we don't have valid (but incorrect) leases. Do the same, consistently, at
other sites where I_COMPLETE is similarly cleared.
Sage Weil [Thu, 13 May 2010 19:01:13 +0000 (12:01 -0700)]
ceph: fix race between aborted requests and fill_trace
When we abort requests we need to prevent fill_trace et al from doing
anything that relies on locks held by the VFS caller. This fixes a race
between the reply handler and the abort code, ensuring that continue
holding the dir mutex until the reply handler completes.
Sage Weil [Thu, 13 May 2010 18:19:06 +0000 (11:19 -0700)]
ceph: clean up mds reply, error handling
We would occasionally BUG out in the reply handler because r_reply was
nonzero, due to a race with ceph_mdsc_do_request temporarily setting
r_reply to an ERR_PTR value. This is unnecessary, messy, and also wrong
in the EIO case.
Clean up by consistently using r_err for errors and r_reply for messages.
Also fix the abort logic to trigger consistently for all errors that return
to the caller early (e.g., EIO from timeout case). If an abort races with
a reply, use the result from the reply.
Also fix locking for r_err, r_reply update in the reply handler.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
rtnetlink: make SR-IOV VF interface symmetric
sctp: delete active ICMP proto unreachable timer when free transport
tcp: fix MD5 (RFC2385) support
Linus Torvalds [Sun, 16 May 2010 18:11:31 +0000 (11:11 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Oprofile: Fix Loongson irq handler
MIPS: N32: Use compat version for sys_ppoll.
MIPS FPU emulator: allow Cause bits of FCSR to be writeable by ctc1
Wei Yongjun [Sun, 9 May 2010 16:56:07 +0000 (16:56 +0000)]
sctp: delete active ICMP proto unreachable timer when free transport
transport may be free before ICMP proto unreachable timer expire, so
we should delete active ICMP proto unreachable timer when transport
is going away.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 16 May 2010 07:34:04 +0000 (00:34 -0700)]
tcp: fix MD5 (RFC2385) support
TCP MD5 support uses percpu data for temporary storage. It currently
disables preemption so that same storage cannot be reclaimed by another
thread on same cpu.
We also have to make sure a softirq handler wont try to use also same
context. Various bug reports demonstrated corruptions.
Fix is to disable preemption and BH.
Reported-by: Bhaskar Dutta <bhaskie@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wu Zhangjin [Thu, 6 May 2010 16:59:46 +0000 (00:59 +0800)]
MIPS: Oprofile: Fix Loongson irq handler
The interrupt enable bit for the performance counters is in the Control
Register $24, not in the counter register.
loongson2_perfcount_handler(), we need to use
Shane McDonald [Fri, 7 May 2010 05:26:57 +0000 (23:26 -0600)]
MIPS FPU emulator: allow Cause bits of FCSR to be writeable by ctc1
In the FPU emulator code of the MIPS, the Cause bits of the FCSR register
are not currently writeable by the ctc1 instruction. In odd corner cases,
this can cause problems. For example, a case existed where a divide-by-zero
exception was generated by the FPU, and the signal handler attempted to
restore the FPU registers to their state before the exception occurred. In
this particular setup, writing the old value to the FCSR register would
cause another divide-by-zero exception to occur immediately. The solution
is to change the ctc1 instruction emulator code to allow the Cause bits of
the FCSR register to be writeable. This is the behaviour of the hardware
that the code is emulating.
This problem was found by Shane McDonald, but the credit for the fix goes
to Kevin Kissell. In Kevin's words:
I submit that the bug is indeed in that ctc_op: case of the emulator. The
Cause bits (17:12) are supposed to be writable by that instruction, but the
CTC1 emulation won't let them be updated by the instruction. I think that
actually if you just completely removed lines 387-388 [...] things would
work a good deal better. At least, it would be a more accurate emulation of
the architecturally defined FPU. If I wanted to be really, really pedantic
(which I sometimes do), I'd also protect the reserved bits that aren't
necessarily writable.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
To: anemo@mba.ocn.ne.jp
To: kevink@paralogos.com
To: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/1205/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
Nicolas Ferre [Sat, 15 May 2010 16:32:31 +0000 (12:32 -0400)]
mmc: at91_mci: modify cache flush routines
As we were using an internal dma flushing routine, this patch changes to
the DMA API flush_kernel_dcache_page(). Driver is able to compile now.
[akpm@linux-foundation.org: flush_kernel_dcache_page() comes before kunmap_atomic()] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 15 May 2010 16:03:15 +0000 (09:03 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
JFS: Free sbi memory in error path
fs/sysv: dereferencing ERR_PTR()
Fix double-free in logfs
Fix the regression created by "set S_DEAD on unlink()..." commit
Linus Torvalds [Sat, 15 May 2010 16:03:02 +0000 (09:03 -0700)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf record: Add a fallback to the reference relocation symbol
Jan Blunck [Mon, 12 Apr 2010 23:44:08 +0000 (16:44 -0700)]
JFS: Free sbi memory in error path
I spotted the missing kfree() while removing the BKL.
[akpm@linux-foundation.org: avoid multiple returns so it doesn't happen again] Signed-off-by: Jan Blunck <jblunck@suse.de> Cc: Dave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Fri, 30 Apr 2010 21:17:09 +0000 (17:17 -0400)]
Fix the regression created by "set S_DEAD on unlink()..." commit
1) i_flags simply doesn't work for mount/unlink race prevention;
we may have many links to file and rm on one of those obviously
shouldn't prevent bind on top of another later on. To fix it
right way we need to mark _dentry_ as unsuitable for mounting
upon; new flag (DCACHE_CANT_MOUNT) is protected by d_flags and
i_mutex on the inode in question. Set it (with dont_mount(dentry))
in unlink/rmdir/etc., check (with cant_mount(dentry)) in places
in namespace.c that used to check for S_DEAD. Setting S_DEAD
is still needed in places where we used to set it (for directories
getting killed), since we rely on it for readdir/rmdir race
prevention.
2) rename()/mount() protection has another bogosity - we unhash
the target before we'd checked that it's not a mountpoint. Fixed.
3) ancient bogosity in pivot_root() - we locked i_mutex on the
right directory, but checked S_DEAD on the different (and wrong)
one. Noticed and fixed.
Linus Torvalds [Sat, 15 May 2010 04:28:42 +0000 (21:28 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6126/1: ARM mpcore_wdt: fix build failure and other fixes
ARM: 6125/1: ARM TWD: move TWD registers to common header
ARM: 6110/1: Fix Thumb-2 kernel builds when UACCESS_WITH_MEMCPY is enabled
ARM: 6112/1: Use the Inner Shareable I-cache and BTB ops on ARMv7 SMP
ARM: 6111/1: Implement read/write for ownership in the ARMv6 DMA cache ops
ARM: 6106/1: Implement copy_to_user_page() for noMMU
ARM: 6105/1: Fix the __arm_ioremap_caller() definition in nommu.c
Hugh Dickins [Sat, 15 May 2010 02:44:10 +0000 (19:44 -0700)]
profile: fix stats and data leakage
If the kernel is large or the profiling step small, /proc/profile
leaks data and readprofile shows silly stats, until readprofile -r
has reset the buffer: clear the prof_buffer when it is vmalloc()ed.
H. Peter Anvin [Fri, 14 May 2010 20:55:57 +0000 (13:55 -0700)]
x86, mrst: Don't blindly access extended config space
Do not blindly access extended configuration space unless we actively
know we're on a Moorestown platform. The fixed-size BAR capability
lives in the extended configuration space, and thus is not applicable
if the configuration space isn't appropriately sized.
This fixes booting certain VMware configurations with CONFIG_MRST=y.
Moorestown will add a fake PCI-X 266 capability to advertise the
presence of extended configuration space.
Reported-and-tested-by: Petr Vandrovec <petr@vandrovec.name> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Acked-by: Jacob Pan <jacob.jun.pan@intel.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <AANLkTiltKUa3TrKR1M51eGw8FLNoQJSLT0k0_K5X3-OJ@mail.gmail.com>
Linus Torvalds [Fri, 14 May 2010 19:20:09 +0000 (12:20 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cacheinfo: Turn off L3 cache index disable feature in virtualized environments
x86, k8: Fix build error when K8_NB is disabled
x86, amd: Check X86_FEATURE_OSVW bit before accessing OSVW MSRs
x86: Fix fake apicid to node mapping for numa emulation
The L3 cache index disable feature of AMD CPUs has to be disabled if the
kernel is running as guest on top of a hypervisor because northbridge
devices are not available to the guest. Currently, this fixes a boot
crash on top of Xen. In the future this will become an issue on KVM as
well.
Check if northbridge devices are present and do not enable the feature
if there are none.
[ hpa: backported to 2.6.34 ]
Signed-off-by: Frank Arnold <frank.arnold@amd.com>
LKML-Reference: <1271945222-5283-3-git-send-email-bp@amd64.org> Acked-by: Borislav Petkov <borislav.petkov@amd.com> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org>
K8_NB depends on PCI and when the last is disabled (allnoconfig) we fail
at the final linking stage due to missing exported num_k8_northbridges.
Add a header stub for that.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100503183036.GJ26107@aftab> Signed-off-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org>
Linus Torvalds [Fri, 14 May 2010 18:49:42 +0000 (11:49 -0700)]
Merge branch 'for-linus' of git://git.infradead.org/users/eparis/notify
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
inotify: don't leak user struct on inotify release
inotify: race use after free/double free in inotify inode marks
inotify: clean up the inotify_add_watch out path
Inotify: undefined reference to `anon_inode_getfd'
Manual merge to remove duplicate "select ANON_INODES" from Kconfig file
Sergei Shtylyov [Thu, 13 May 2010 18:51:51 +0000 (22:51 +0400)]
DA830: fix USB 2.0 clock entry
DA8xx OHCI driver fails to load due to failing clk_get() call for the USB 2.0
clock. Arrange matching USB 2.0 clock by the clock name instead of the device.
(Adding another CLK() entry for "ohci.0" device won't do -- in the future I'll
also have to enable USB 2.0 clock to configure CPPI 4.1 module, in which case
I won't have any device at all.)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Pavel Emelyanov [Wed, 12 May 2010 22:34:07 +0000 (15:34 -0700)]
inotify: don't leak user struct on inotify release
inotify_new_group() receives a get_uid-ed user_struct and saves the
reference on group->inotify_data.user. The problem is that free_uid() is
never called on it.
Issue seem to be introduced by 63c882a0 (inotify: reimplement inotify
using fsnotify) after 2.6.30.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Eric Paris <eparis@parisplace.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Eric Paris <eparis@redhat.com>
Eric Paris [Tue, 11 May 2010 21:17:40 +0000 (17:17 -0400)]
inotify: race use after free/double free in inotify inode marks
There is a race in the inotify add/rm watch code. A task can find and
remove a mark which doesn't have all of it's references. This can
result in a use after free/double free situation.
Task A Task B
------------ -----------
inotify_new_watch()
allocate a mark (refcnt == 1)
add it to the idr
inotify_rm_watch()
inotify_remove_from_idr()
fsnotify_put_mark()
refcnt hits 0, free
take reference because we are on idr
[at this point it is a use after free]
[time goes on]
refcnt may hit 0 again, double free
The fix is to take the reference BEFORE the object can be found in the
idr.
Signed-off-by: Eric Paris <eparis@redhat.com> Cc: <stable@kernel.org>
Linus Torvalds [Fri, 14 May 2010 14:29:29 +0000 (07:29 -0700)]
Merge branch 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Fix module loading on system with WB cache
microblaze: export assembly functions used by modules
microblaze: Remove powerpc code from Microblaze port
microblaze: Remove compilation warnings in cache macro
microblaze: export assembly functions used by modules
microblaze: fix get_user/put_user side-effects
microblaze: re-enable interrupts before calling schedule
Redirecting directly to lsm, here's the patch discussed on lkml:
http://lkml.org/lkml/2010/4/22/219
The mmap_min_addr value is useful information for an admin to see without
being root ("is my system vulnerable to kernel NULL pointer attacks?") and
its setting is trivially easy for an attacker to determine by calling
mmap() in PAGE_SIZE increments starting at 0, so trying to keep it private
has no value.
Only require CAP_SYS_RAWIO if changing the value, not reading it.
Comment from Serge :
Me, I like to write my passwords with light blue pen on dark blue
paper, pasted on my window - if you're going to get my password, you're
gonna get a headache.
Signed-off-by: Kees Cook <kees.cook@canonical.com> Acked-by: Serge Hallyn <serue@us.ibm.com> Signed-off-by: James Morris <jmorris@namei.org>
(cherry picked from commit 822cceec7248013821d655545ea45d1c6a9d15b3)
Linus Torvalds [Thu, 13 May 2010 21:36:19 +0000 (14:36 -0700)]
Merge branch 'kvm-updates/2.6.34' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.34' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Keep index within boundaries in kvmppc_44x_emul_tlbwe()
KVM: VMX: blocked-by-sti must not defer NMI injections
KVM: x86: Call vcpu_load and vcpu_put in cpuid_update
KVM: SVM: Fix wrong intercept masks on 32 bit
KVM: convert ioapic lock to spinlock
serial: imx.c: fix CTS trigger level lower to avoid lost chars
The imx CTS trigger level is left at its reset value that is 32
chars. Since the RX FIFO has 32 entries, when CTS is raised, the
FIFO already is full. However, some serial port devices first empty
their TX FIFO before stopping when CTS is raised, resulting in lost
chars.
This patch sets the trigger level lower so that other chars arrive
after CTS is raised, there is still room for 16 of them.
Alan Cox [Tue, 4 May 2010 19:42:36 +0000 (20:42 +0100)]
tty: Fix unbalanced BKL handling in error path
Arnd noted:
After the "retry_open:" label, we first get the tty_mutex
and then the BKL. However a the end of tty_open, we jump
back to retry_open with the BKL still held. If we run into
this case, the tty_open function will be left with the BKL
still held.
Jan Kara [Thu, 13 May 2010 10:52:57 +0000 (12:52 +0200)]
vfs: Fix O_NOFOLLOW behavior for paths with trailing slashes
According to specification
mkdir d; ln -s d a; open("a/", O_NOFOLLOW | O_RDONLY)
should return success but currently it returns ELOOP. This is a
regression caused by path lookup cleanup patch series.
Fix the code to ignore O_NOFOLLOW in case the provided path has trailing
slashes.
Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Reported-by: Marius Tolzmann <tolzmann@molgen.mpg.de> Acked-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 13 May 2010 14:35:26 +0000 (07:35 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ice1724 - Fix ESI Maya44 capture source control
ALSA: pcm - Use pgprot_noncached() for MIPS non-coherent archs
ALSA: virtuoso: fix Xonar D1/DX front panel microphone
ALSA: hda - Add hp-dv4 model for IDT 92HD71bx
ALSA: hda - Fix mute-LED GPIO pin for HP dv series
ALSA: hda: Fix 0 dB for Lenovo models using Conexant CX20549 (Venice)
Linus Torvalds [Thu, 13 May 2010 14:28:43 +0000 (07:28 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad7877 - keep dma rx buffers in seperate cache lines
Input: psmouse - reset all types of mice before reconnecting
Input: elantech - use all 3 bytes when checking version
Input: iforce - fix Guillemot Jet Leader 3D entry
Input: iforce - add Guillemot Jet Leader Force Feedback
Mark Brown [Fri, 2 Apr 2010 12:08:39 +0000 (13:08 +0100)]
mfd: Clean up after WM83xx AUXADC interrupt if it arrives late
In certain circumstances, especially under heavy load, the AUXADC
completion interrupt may be detected after we've timed out waiting for
it. That conversion would still succeed but the next conversion will
see the completion that was signalled by the interrupt for the previous
conversion and therefore not wait for the AUXADC conversion to run,
causing it to report failure.
Provide a simple, non-invasive cleanup by using try_wait_for_completion()
to ensure that the completion is not signalled before we wait. Since
the AUXADC is run within a mutex we know there can only have been at
most one AUXADC interrupt outstanding. A more involved change should
follow for the next merge window.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Michal Simek [Thu, 13 May 2010 08:55:47 +0000 (10:55 +0200)]
microblaze: Remove compilation warnings in cache macro
CC arch/microblaze/kernel/cpu/cache.o
arch/microblaze/kernel/cpu/cache.c: In function '__invalidate_dcache_range_wb':
arch/microblaze/kernel/cpu/cache.c:398: warning: ISO C90 forbids mixed declarations and code
arch/microblaze/kernel/cpu/cache.c: In function '__flush_dcache_range_wb':
arch/microblaze/kernel/cpu/cache.c:509: warning: ISO C90 forbids mixed declara
With dma based spi transmission, data corruption is observed
occasionally. With dma buffers located right next to msg and
xfer fields, cache lines correctly flushed in preparation for
dma usage may be polluted again when writing to fields in the
same cache line.
Make sure cache fields used with dma do not share cache lines
with fields changed during dma handling. As both fields are part
of a struct that is allocated via kzalloc, thus cache aligned,
moving the fields to the 1st position and insert padding for
alignment does the job.
Signed-off-by: Oskar Schirmer <os@emlix.com> Signed-off-by: Daniel Glöckner <dg@emlix.com> Signed-off-by: Oliver Schneidewind <osw@emlix.com> Signed-off-by: Johannes Weiner <jw@emlix.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
[dtor@mail.ru - changed to use ___cacheline_aligned as suggested
by akpm] Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dmitry Torokhov [Thu, 13 May 2010 07:42:23 +0000 (00:42 -0700)]
Input: psmouse - reset all types of mice before reconnecting
Synaptics hardware requires resetting device after suspend to ram
in order for the device to be operational. The reset lives in
synaptics-specific reconnect handler, but it is not being invoked
if synaptics support is disabled and the device is handled as a
standard PS/2 device (bare or IntelliMouse protocol).
Let's add reset into generic reconnect handler as well.
The Microblaze implementations of get_user() and (MMU) put_user() evaluate
the address argument more than once. This causes unexpected side-effects for
invocations that include increment operators, i.e. get_user(foo, bar++).
This patch also removes the distinction between MMU and noMMU put_user().
Without the patch:
$ echo 1234567890 > /proc/sys/kernel/core_pattern
$ cat /proc/sys/kernel/core_pattern
12345
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
perf record: Add a fallback to the reference relocation symbol
Usually "_text" is enough, but I received reports that its not always
available, so fallback to "_stext" for the symbol we use to check if we
need to apply any relocation to all the symbols in the kernel symtab,
for when, for instance, kexec is being used.
Reported-by: Darren Hart <dvhltc@us.ibm.com> Reported-by: Steven Rostedt <rostedt@goodmis.org> Cc: Frédéric Weisbecker <fweisbec@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jan Kiszka [Tue, 11 May 2010 13:16:46 +0000 (15:16 +0200)]
KVM: VMX: blocked-by-sti must not defer NMI injections
As the processor may not consider GUEST_INTR_STATE_STI as a reason for
blocking NMI, it could return immediately with EXIT_REASON_NMI_WINDOW
when we asked for it. But as we consider this state as NMI-blocking, we
can run into an endless loop.
Resolve this by allowing NMI injection if just GUEST_INTR_STATE_STI is
active (originally suggested by Gleb). Intel confirmed that this is
safe, the processor will never complain about NMI injection in this
state.
Joerg Roedel [Wed, 5 May 2010 14:04:43 +0000 (16:04 +0200)]
KVM: SVM: Fix wrong intercept masks on 32 bit
This patch makes KVM on 32 bit SVM working again by
correcting the masks used for iret interception. With the
wrong masks the upper 32 bits of the intercepts are masked
out which leaves vmrun unintercepted. This is not legal on
svm and the vmrun fails.
Bug was introduced by commits 95ba827313 and 3cfc3092.
Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Gleb Natapov <gleb@redhat.com> Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@redhat.com>
Linus Torvalds [Thu, 13 May 2010 01:48:26 +0000 (18:48 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf_event: Fix oops due to perf_event_do_pending call
powerpc/swiotlb: Fix off by one in determining boundary of which ops to use
Linus Torvalds [Thu, 13 May 2010 01:47:55 +0000 (18:47 -0700)]
Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] correct address of _stext with CONFIG_SHARED_KERNEL=y
[S390] ptrace: fix return value of do_syscall_trace_enter()
[S390] dasd: fix race between tasklet and dasd_sleep_on
Linus Torvalds [Thu, 13 May 2010 01:47:29 +0000 (18:47 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: preserve seq # on requeued messages after transient transport errors
ceph: fix cap removal races
ceph: zero unused message header, footer fields
ceph: fix locking for waking session requests after reconnect
ceph: resubmit requests on pg mapping change (not just primary change)
ceph: fix open file counting on snapped inodes when mds returns no caps
ceph: unregister osd request on failure
ceph: don't use writeback_control in writepages completion
ceph: unregister bdi before kill_anon_super releases device name
Linus Torvalds [Thu, 13 May 2010 01:39:45 +0000 (18:39 -0700)]
Revert "PCI: update bridge resources to get more big ranges in PCI assign unssigned"
This reverts commit 977d17bb1749517b353874ccdc9b85abc7a58c2a, because it
can cause problems with some devices not getting any resources at all
when the resource tree is re-allocated.
David Howells [Wed, 12 May 2010 14:34:03 +0000 (15:34 +0100)]
CacheFiles: Fix error handling in cachefiles_determine_cache_security()
cachefiles_determine_cache_security() is expected to return with a
security override in place. However, if set_create_files_as() fails, we
fail to do this. In this case, we should just reinstate the security
override that was set by the caller.
Furthermore, if set_create_files_as() fails, we should dispose of the
new credentials we were in the process of creating.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rwsem: Test for no active locks in __rwsem_do_wake undo code
If there are no active threasd using a semaphore, it is always correct
to unqueue blocked threads. This seems to be what was intended in the
undo code.
What was done instead, was to look for a sem count of zero - this is an
impossible situation, given that at least one thread is known to be
queued on the semaphore. The code might be correct as written, but it's
hard to reason about and it's not what was intended (otherwise the goto
out would have been unconditional).
Go for checking the active count - the alternative is not worth the
headache.
Signed-off-by: Michel Lespinasse <walken@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to memory-barriers.txt, an smp memory barrier in guest
should always be paired with an smp memory barrier in host,
and I quote "a lack of appropriate pairing is almost certainly an
error". In case of vhost, failure to flush out used index
update before looking at the interrupt disable flag
could result in missed interrupts, resulting in
networking hang under stress.
This might happen when flags read bypasses used index write.
So we see interrupts disabled and do not interrupt, at the
same time guest writes flags value to enable interrupt,
reads an old used index value, thinks that
used ring is empty and waits for interrupt.
Note: the barrier we pair with here is in
drivers/virtio/virtio_ring.c, function
vring_enable_cb.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Juan Quintela <quintela@redhat.com>
Russell King [Sun, 18 Apr 2010 20:25:11 +0000 (21:25 +0100)]
Inotify: undefined reference to `anon_inode_getfd'
Fix:
fs/built-in.o: In function `sys_inotify_init1':
summary.c:(.text+0x347a4): undefined reference to `anon_inode_getfd'
found by kautobuild with arms bcmring_defconfig, which ends up with
INOTIFY_USER enabled (through the 'default y') but leaves ANON_INODES
unset. However, inotify_user.c uses anon_inode_getfd().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Eric Paris <eparis@redhat.com>
Takashi Iwai [Wed, 12 May 2010 14:43:32 +0000 (16:43 +0200)]
ALSA: ice1724 - Fix ESI Maya44 capture source control
The capture source control of maya44 was wrongly coded with the bit
shift instead of the bit mask. Also, the slot for line-in was
wrongly assigned (slot 5 instead of 4).
Reported-by: Alex Chernyshoff <alexdsp@gmail.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Srinidhi Kasagar [Wed, 12 May 2010 04:53:26 +0000 (05:53 +0100)]
ARM: 6126/1: ARM mpcore_wdt: fix build failure and other fixes
This fixes the build failures seen when building mpcore_wdt and it
also removes the nonexistent ARM_MPCORE_PLATFORM dependency, instead
make it dependent on HAVE_ARM_TWD.
Also this fixes spinlock usage appropriately.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Takashi Iwai [Wed, 12 May 2010 08:32:42 +0000 (10:32 +0200)]
ALSA: pcm - Use pgprot_noncached() for MIPS non-coherent archs
MIPS non-coherent archs need the noncached pgprot in mmap of PCM buffers.
But, since the coherency needs to be checked dynamically via
plat_device_is_coherent(), we need an ugly check dependent on MIPS
in ALSA core code.
This should be cleaned up in MIPS arch side (e.g. creating
dma_mmap_coherent()) in near future.
Clemens Ladisch [Tue, 11 May 2010 14:34:39 +0000 (16:34 +0200)]
ALSA: virtuoso: fix Xonar D1/DX front panel microphone
Commit 65c3ac885ce9852852b895a4a62212f62cb5f2e9 in 2.6.33 accidentally
left out the initialization of the AC97 codec FMIC2MIC bit, which broke
recording from the front panel microphone.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: <stable@kernel.org> Signed-off-by: Jaroslav Kysela <perex@perex.cz> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 12 May 2010 08:16:20 +0000 (10:16 +0200)]
ALSA: hda - Add hp-dv4 model for IDT 92HD71bx
It turned out that HP dv series have inconsistent the mute-LED GPIO
mapping among various models. dv4/7 seem to use GPIO 0 while dv 5/6
seem to use GPIO 3. The previous commit 26ebe0a28986f4845b2c5bea43ac5cc0b9f27f0a
ALSA: hda - Fix mute-LED GPIO pin for HP dv series
breaks dv5/6.
This patch adds the new quirk model, hp-dv4, to handle HP dv4/7
separately from HP dv5/6.
[S390] correct address of _stext with CONFIG_SHARED_KERNEL=y
As of git commit 1844c9bc0b2fed3023551c1affe033ab38e90b9a head64.S/head31.S
are not included in head.S anymore but build as an extra object. This breaks
shared kernel support because the .org statement in head64.S/head31.S for
CONFIG_SHARED_KERNEL=y will have a different effect. The end address of the
head.text section in head.o will be added to the .org value, to compensate
for this subtract 0x11000 to get the required value of 0x100000 again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Gerald Schaefer [Wed, 12 May 2010 07:32:12 +0000 (09:32 +0200)]
[S390] ptrace: fix return value of do_syscall_trace_enter()
strace may change the system call number, so regs->gprs[2] must not
be read before tracehook_report_syscall_entry(). This fixes a bug
where "strace -f" will hang after a vfork().
Cc: <stable@kernel.org> Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stefan Weinhuber [Wed, 12 May 2010 07:32:11 +0000 (09:32 +0200)]
[S390] dasd: fix race between tasklet and dasd_sleep_on
The various dasd_sleep_on functions use a global wait queue when
waiting for a cqr. The wait condition checks the status and devlist
fields of the cqr to determine if it is safe to continue. This
evaluation may return true, although the tasklet has not finished
processing of the cqr and the callback function has not been called
yet. When the callback is finally called, the data in the cqr may
already be invalid. The sleep_on wait condition needs a safe way to
determine if the tasklet has finished processing. Use the
callback_data field of the cqr to store a token, which is set by
the callback function itself.
Cc: <stable@kernel.org> Signed-off-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Paul Mackerras [Tue, 13 Apr 2010 20:46:04 +0000 (20:46 +0000)]
powerpc/perf_event: Fix oops due to perf_event_do_pending call
Anton Blanchard found that large POWER systems would occasionally
crash in the exception exit path when profiling with perf_events.
The symptom was that an interrupt would occur late in the exit path
when the MSR[RI] (recoverable interrupt) bit was clear. Interrupts
should be hard-disabled at this point but they were enabled. Because
the interrupt was not recoverable the system panicked.
The reason is that the exception exit path was calling
perf_event_do_pending after hard-disabling interrupts, and
perf_event_do_pending will re-enable interrupts.
The simplest and cleanest fix for this is to use the same mechanism
that 32-bit powerpc does, namely to cause a self-IPI by setting the
decrementer to 1. This means we can remove the tests in the exception
exit path and raw_local_irq_restore.
This also makes sure that the call to perf_event_do_pending from
timer_interrupt() happens within irq_enter/irq_exit. (Note that
calling perf_event_do_pending from timer_interrupt does not mean that
there is a possible 1/HZ latency; setting the decrementer to 1 ensures
that the timer interrupt will happen immediately, i.e. within one
timebase tick, which is a few nanoseconds or 10s of nanoseconds.)
Signed-off-by: Paul Mackerras <paulus@samba.org> Cc: stable@kernel.org Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Sage Weil [Wed, 12 May 2010 04:20:38 +0000 (21:20 -0700)]
ceph: preserve seq # on requeued messages after transient transport errors
If the tcp connection drops and we reconnect to reestablish a stateful
session (with the mds), we need to resend previously sent (and possibly
received) messages with the _same_ seq # so that they can be dropped on
the other end if needed. Only assign a new seq once after the message is
queued.
Sage Weil [Wed, 12 May 2010 03:56:31 +0000 (20:56 -0700)]
ceph: fix cap removal races
The iterate_session_caps helper traverses the session caps list and tries
to grab an inode reference. However, the __ceph_remove_cap was clearing
the inode backpointer _before_ removing itself from the session list,
causing a null pointer dereference.
Clear cap->ci under protection of s_cap_lock to avoid the race, and to
tightly couple the list and backpointer state. Use a local flag to
indicate whether we are releasing the cap, as cap->session may be modified
by a racing thread in iterate_session_caps.
Oliver Neukum [Tue, 11 May 2010 21:07:03 +0000 (14:07 -0700)]
hp_accel: fix race in device removal
The work queue has to be flushed after the device has been made
inaccessible. The patch closes a window during which a work queue might
remain active after the device is removed and would then lead to ACPI
calls with undefined behavior.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Acked-by: Eric Piel <eric.piel@tremplin-utc.net> Acked-by: Pavel Machek <pavel@ucw.cz> Cc: Pavel Herrmann <morpheus.ibis@gmail.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mqueue: fix kernel BUG caused by double free() on mq_open()
In case of aborting because we reach the maximum amount of memory which
can be allocated to message queues per user (RLIMIT_MSGQUEUE), we would
try to free the message area twice when bailing out: first by the error
handling code itself, and then later when cleaning up the inode through
delete_inode().
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fbdev: bfin-t350mcqb-fb: fix fbmem allocation with blanking lines
The current allocation does not include the memory required for blanking
lines. So avoid memory corruption when multiple devices are using the DMA
memory near each other.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some callers (in memcontrol.c) calls css_is_ancestor() without
rcu_read_lock. Because css_is_ancestor() has to access RCU protected
data, it should be under rcu_read_lock().
This makes css_is_ancestor() itself does safe access to RCU protected
area. (At least, "root" can have refcnt==0 if it's not an ancestor of
"child". So, we need rcu_read_lock().)