Andi Kleen [Wed, 16 Dec 2009 11:20:00 +0000 (12:20 +0100)]
HWPOISON: Add a madvise() injector for soft page offlining
Process based injection is much easier to handle for test programs,
who can first bring a page into a specific state and then test.
So add a new MADV_SOFT_OFFLINE to soft offline a page, similar
to the existing hard offline injector.
Andi Kleen [Wed, 16 Dec 2009 11:20:00 +0000 (12:20 +0100)]
HWPOISON: Add soft page offline support
This is a simpler, gentler variant of memory_failure() for soft page
offlining controlled from user space. It doesn't kill anything, just
tries to invalidate and if that doesn't work migrate the
page away.
This is useful for predictive failure analysis, where a page has
a high rate of corrected errors, but hasn't gone bad yet. Instead
it can be offlined early and avoided.
The offlining is controlled from sysfs, including a new generic
entry point for hard page offlining for symmetry too.
We use the page isolate facility to prevent re-allocation
race. Normally this is only used by memory hotplug. To avoid
races with memory allocation I am using lock_system_sleep().
This avoids the situation where memory hotplug is about
to isolate a page range and then hwpoison undoes that work.
This is a big hammer currently, but the simplest solution
currently.
When the page is not free or LRU we try to free pages
from slab and other caches. The slab freeing is currently
quite dumb and does not try to focus on the specific slab
cache which might own the page. This could be potentially
improved later.
Thanks to Fengguang Wu and Haicheng Li for some fixes.
[Added fix from Andrew Morton to adapt to new migrate_pages prototype] Signed-off-by: Andi Kleen <ak@linux.intel.com>
Andi Kleen [Wed, 16 Dec 2009 11:20:00 +0000 (12:20 +0100)]
HWPOISON: Use get_user_page_fast in hwpoison madvise
The previous version didn't take the mmap_sem before calling gup(),
which is racy.
Use get_user_pages_fast() instead which doesn't need any locks.
This is also faster of course, but then it doesn't really matter
because this is just a testing path.
Based on report from Nick Piggin. Cc: npiggin@suse.de Signed-off-by: Andi Kleen <ak@linux.intel.com>
Haicheng Li [Wed, 16 Dec 2009 11:19:59 +0000 (12:19 +0100)]
HWPOISON: add an interface to switch off/on all the page filters
In some use cases, user doesn't need extra filtering. E.g. user program
can inject errors through madvise syscall to its own pages, however it
might not know what the page state exactly is or which inode the page
belongs to.
So introduce an one-off interface "corrupt-filter-enable".
Echo 0 to switch off page filters, and echo 1 to switch on the filters.
[AK: changed default to 0]
Andi Kleen [Wed, 16 Dec 2009 11:19:59 +0000 (12:19 +0100)]
HWPOISON: add memory cgroup filter
The hwpoison test suite need to inject hwpoison to a collection of
selected task pages, and must not touch pages not owned by them and
thus kill important system processes such as init. (But it's OK to
mis-hwpoison free/unowned pages as well as shared clean pages.
Mis-hwpoison of shared dirty pages will kill all tasks, so the test
suite will target all or non of such tasks in the first place.)
The memory cgroup serves this purpose well. We can put the target
processes under the control of a memory cgroup, and tell the hwpoison
injection code to only kill pages associated with some active memory
cgroup.
The prerequisite for doing hwpoison stress tests with mem_cgroup is,
the mem_cgroup code tracks task pages _accurately_ (unless page is
locked). Which we believe is/should be true.
The benefits are simplification of hwpoison injector code. Also the
mem_cgroup code will automatically be tested by hwpoison test cases.
The alternative interfaces pin-pfn/unpin-pfn can also delegate the
(process and page flags) filtering functions reliably to user space.
However prototype implementation shows that this scheme adds more
complexity than we wanted.
This allows stress testing of many kinds of pages.
Strictly speaking, the buddy pages requires taking zone lock, to avoid
setting PG_hwpoison on a "was buddy but now allocated to someone" page.
However we can just do nothing because we set PG_locked in the beginning,
this prevents the page allocator from allocating it to someone. (It will
BUG() on the unexpected PG_locked, which is fine for hwpoison testing.)
[AK: Add select PROC_PAGE_MONITOR to satisfy dependency]
Wu Fengguang [Wed, 16 Dec 2009 11:19:59 +0000 (12:19 +0100)]
mm: export stable page flags
Rename get_uflags() to stable_page_flags() and make it a global function
for use in the hwpoison page flags filter, which need to compare user
page flags with the value provided by user space.
Also move KPF_* to kernel-page-flags.h for use by user space tools.
Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> CC: Nick Piggin <npiggin@suse.de> CC: Christoph Lameter <cl@linux-foundation.org> Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Wu Fengguang [Wed, 16 Dec 2009 11:19:59 +0000 (12:19 +0100)]
HWPOISON: limit hwpoison injector to known page types
__memory_failure()'s workflow is
set PG_hwpoison
//...
unset PG_hwpoison if didn't pass hwpoison filter
That could kill unrelated process if it happens to page fault on the
page with the (temporary) PG_hwpoison. The race should be big enough to
appear in stress tests.
Fix it by grabbing the page and checking filter at inject time. This
also avoids the very noisy "Injecting memory failure..." messages.
- we don't touch madvise() based injection, because the filters are
generally not necessary for it.
- if we want to apply the filters to h/w aided injection, we'd better to
rearrange the logic in __memory_failure() instead of this patch.
Wu Fengguang [Wed, 16 Dec 2009 11:19:59 +0000 (12:19 +0100)]
HWPOISON: add fs/device filters
Filesystem data/metadata present the most tricky-to-isolate pages.
It requires careful code review and stress testing to get them right.
The fs/device filter helps to target the stress tests to some specific
filesystem pages. The filter condition is block device's major/minor
numbers:
- corrupt-filter-dev-major
- corrupt-filter-dev-minor
When specified (non -1), only page cache pages that belong to that
device will be poisoned.
The filters are checked reliably on the locked and refcounted page.
Haicheng: clear PG_hwpoison and drop bad page count if filter not OK
AK: Add documentation
CC: Haicheng Li <haicheng.li@intel.com> CC: Nick Piggin <npiggin@suse.de> Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Wu Fengguang [Wed, 16 Dec 2009 11:19:58 +0000 (12:19 +0100)]
HWPOISON: Add unpoisoning support
The unpoisoning interface is useful for stress testing tools to
reclaim poisoned pages (to prevent OOM)
There is no hardware level unpoisioning, so this
cannot be used for real memory errors, only for software injected errors.
Note that it may leak pages silently - those who have been removed from
LRU cache, but not isolated from page cache/swap cache at hwpoison time.
Especially the stress test of dirty swap cache pages shall reboot system
before exhausting memory.
AK: Fix comments, add documentation, add printks, rename symbol
Wu Fengguang [Wed, 16 Dec 2009 11:19:58 +0000 (12:19 +0100)]
HWPOISON: introduce delete_from_lru_cache()
Introduce delete_from_lru_cache() to
- clear PG_active, PG_unevictable to avoid complains at unpoison time
- move the isolate_lru_page() call back to the handlers instead of the
entrance of __memory_failure(), this is more hwpoison filter friendly
Andi Kleen [Wed, 16 Dec 2009 11:19:57 +0000 (12:19 +0100)]
HWPOISON: Turn ref argument into flags argument
Now that "ref" is just a boolean turn it into
a flags argument. First step is only a single flag
that makes the code's intention more clear, but more
may follow.
Wu Fengguang [Wed, 16 Dec 2009 11:19:57 +0000 (12:19 +0100)]
HWPOISON: avoid grabbing the page count multiple times during madvise injection
If page is double referenced in madvise_hwpoison() and __memory_failure(),
remove_mapping() will fail because it expects page_count=2. Fix it by
not grabbing extra page count in __memory_failure().
This file seems to have been missed in the renaming.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 15 Dec 2009 17:12:43 +0000 (09:12 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: event tracing support
xfs: change the xfs_iext_insert / xfs_iext_remove
xfs: cleanup bmap extent state macros
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (80 commits)
dm snapshot: use merge origin if snapshot invalid
dm snapshot: report merge failure in status
dm snapshot: merge consecutive chunks together
dm snapshot: trigger exceptions in remaining snapshots during merge
dm snapshot: delay merging a chunk until writes to it complete
dm snapshot: queue writes to chunks being merged
dm snapshot: add merging
dm snapshot: permit only one merge at once
dm snapshot: support barriers in snapshot merge target
dm snapshot: avoid allocating exceptions in merge
dm snapshot: rework writing to origin
dm snapshot: add merge target
dm exception store: add merge specific methods
dm snapshot: create function for chunk_is_tracked wait
dm snapshot: make bio optional in __origin_write
dm mpath: reject messages when device is suspended
dm: export suspended state to targets
dm: rename dm_suspended to dm_suspended_md
dm: swap target postsuspend call and setting suspended flag
dm crypt: add plain64 iv
...
Linus Torvalds [Tue, 15 Dec 2009 17:11:28 +0000 (09:11 -0800)]
Merge branch 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block:
cfq: set workload as expired if it doesn't have any slice left
Fix a CFQ crash in "for-2.6.33" branch of block tree
cfq: Remove wait_request flag when idle time is being deleted
cfq-iosched: commenting non-obvious initialization
cfq-iosched: Take care of corner cases of group losing share due to deletion
cfq-iosched: Get rid of cfqq wait_busy_done flag
cfq: Optimization for close cooperating queue searching
block,xd: Delay allocation of DMA buffers until device is known
drbd: Following the hmac change to SHASH (see linux commit 8bd1209cfff)
cfq-iosched: reduce write depth only if sync was delayed
Linus Torvalds [Tue, 15 Dec 2009 17:11:05 +0000 (09:11 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ac97_codec - increase timeout for analog sections to 5 second
ASoC: Correct code taking the size of a pointer
ALSA: hda - Add PCI IDs for Nvidia G2xx-series
ALSA: sound/isa/gus: Correct code taking the size of a pointer
ALSA: hda: Fix max PCM level to 0 dB for AD1981_HP
ALSA: hda: Use ALC260_WILL quirk for another Acer model (0x1025007f)
Linus Torvalds [Tue, 15 Dec 2009 17:02:01 +0000 (09:02 -0800)]
Merge branch 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (26 commits)
clockevents: Convert to raw_spinlock
clockevents: Make tick_device_lock static
debugobjects: Convert to raw_spinlocks
perf_event: Convert to raw_spinlock
hrtimers: Convert to raw_spinlocks
genirq: Convert irq_desc.lock to raw_spinlock
smp: Convert smplocks to raw_spinlocks
rtmutes: Convert rtmutex.lock to raw_spinlock
sched: Convert pi_lock to raw_spinlock
sched: Convert cpupri lock to raw_spinlock
sched: Convert rt_runtime_lock to raw_spinlock
sched: Convert rq->lock to raw_spinlock
plist: Make plist debugging raw_spinlock aware
bkl: Fixup core_lock fallout
locking: Cleanup the name space completely
locking: Further name space cleanups
alpha: Fix fallout from locking changes
locking: Implement new raw_spinlock
locking: Convert raw_rwlock functions to arch_rwlock
locking: Convert raw_rwlock to arch_rwlock
...
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: update default configurations for ATNGW100, ATSTK1002 and ATSTK1006
avr32: add default configurations for ATNGW100 mkII and EVKLCD10X
avr32: add support for ATNGW100 mkII board
avr32: convert to asm-generic/hardirq.h
avr32: add two new at91 to cpu.h definition
avr32: clean up linker script using standard macros.
avr32: MRMT: correct setup of SPI slaves
avr32: function for independently setting up SPI slaves
avr32: re-instate MCI WP/CD pin assignments for ATNGW100
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix clock event multiplier printf format.
sparc64: Use clock{source,events}_calc_mult_shift().
sparc64: Use free_bootmem_late() in mdesc_lmb_free().
sparc: Add alignment and emulation fault perf events.
sparc64: Add syscall tracepoint support.
sparc: Stop trying to be so fancy and use __builtin_{memcpy,memset}()
sparc: Use __builtin_object_size() to validate the buffer size for copy_from_user()
sparc64: Add some missing __kprobes annotations to kernel fault paths.
sparc64: Use kprobes_built_in() to avoid ifdefs in fault_64.c
sparc: Validate that kprobe address is 4-byte aligned.
sparc64: Don't specify IRQF_SHARED for LDC interrupts.
sparc64: Fix stack debugging IRQ stack regression.
sparc64: Fix overly strict range type matching for PCI devices.
Linus Torvalds [Tue, 15 Dec 2009 16:59:33 +0000 (08:59 -0800)]
Merge git://git.infradead.org/battery-2.6
* git://git.infradead.org/battery-2.6:
power_supply_sysfs: Handle -ENODATA in a special way
wm831x_backup: Remove unused variables
gta02: Set pcf50633 charger_reference_current_ma
pcf50633: Query charger status directly
pcf50633: Properly reenable charging when the supply conditions change
pcf50633: Get rid of charging restart software auto-triggering
pcf50633: introduces battery charging current control
pcf50633: Add ac power supply class to the charger
wm831x: Factor out WM831x backup battery charger
Samu Onkalo [Tue, 15 Dec 2009 02:01:46 +0000 (18:01 -0800)]
lis3: scale output values to mg
Report output values as 1/1000 of earth gravity.
Output values from lis3 can be read from sysfs position entry and from
input device. Input device can be accessed as event device and as
joystick device. Joystick device can be in two modes. Meaning of the
output values varies from case to case depending on the chip type and
configuration (scale). Only joystick interface in JS_CORR_BROKEN mode
returned somehow similar output values in different configurations.
Joystick device is in that state by default in case of lis3.
Position sysfs entry, input event device and raw joystick device have been
little bit broken since meaning of the output values has been varied
between 12 and 8 bit devices. Applications which relayed on those methods
failed if the chip is different than the expected one.
This patch converts output values to mean similar thing in different
configurations. Both 8 and 12 bit devices reports now same acceleration
values. If somebody implements full scale support to the driver, output
values will still mean the same. Scaling factor and input device range
must be updated in that case.
Joystick interface in JS_CORR_BROKEN mode is not touched by this patch.
All other interfaces have different scale after this change. For 12 bit
device scaling factor is 0.977 which keeps scaled and unscaled values are
quite close to each others. For 8 bit device, scaled values are 18 times
bigger than unscaled values.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Samu Onkalo [Tue, 15 Dec 2009 02:01:43 +0000 (18:01 -0800)]
lis3lv02d: remove calibaration functionality
Chip is calibrated by the manufacturer. There is no need to calibarate it
at driver level. If the chip is used as a joystick, calibaration can be
done using joystick device calibration mechanism.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Samu Onkalo [Tue, 15 Dec 2009 02:01:43 +0000 (18:01 -0800)]
lis3: selftest support
Implement selftest feature as specified by chip manufacturer. Control:
read selftest sysfs entry
Response: "OK x y z" or "FAIL x y z"
where x, y, and z are difference between selftest mode and normal mode.
Test is passed when values are within acceptance limit values.
Acceptance limits are provided via platform data. See chip spesifications
for acceptance limits. If limits are not properly set, OK / FAIL decision
is meaningless. However, userspace application can still make decision
based on the numeric x, y, z values.
Selftest is meant for HW diagnostic purposes. It is not meant to be
called during normal use of the chip. It may cause false interrupt
events. Selftest mode delays polling of the normal results but it doesn't
cause wrong values. Chip must be in static state during selftest. Any
acceration during the test causes most probably failure.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Acked-by: Éric Piel <Eric.Piel@tremplin-utc.net> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Samu Onkalo [Tue, 15 Dec 2009 02:01:41 +0000 (18:01 -0800)]
lis3lv02d: proper power on sequence
Lis3 accelerometer sensors have quite long power on delay (up to 125
ms). This patch adds necessary delay to power on sequence for currently
supported lis3 chips.
Éric Piel [Tue, 15 Dec 2009 02:01:40 +0000 (18:01 -0800)]
lis3: fix show rate for 8 bits chips
Originally the driver was only targeted to 12bits sensors. When support
for 8bits sensors was added, some slight difference in the registers were
overlooked. This should fix it, both for initialization, and for
displaying the rate.
Reported-by: Kalhan Trisal <kalhan.trisal@intel.com> Reported-by: Christoph Plattner <christoph.plattner@gmx.at> Tested-by: Christoph Plattner <christoph.plattner@gmx.at> Tested-by: Samu Onkalo <samu.p.onkalo@nokia.com> Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Éric Piel [Tue, 15 Dec 2009 02:01:39 +0000 (18:01 -0800)]
lis3: update documentation and comments
Most of the documentation and comments were written when the driver was
only supporting one type of chip, only via ACPI/HP. Update the info to
the much clearer understanding that we have now.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net> Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel J Blueman [Tue, 15 Dec 2009 02:01:37 +0000 (18:01 -0800)]
hwmon: w83627ehf updates
Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level. Add control of rate of change of fan output
level. These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority. Add
support for constant fan speed and proportional-response operations modes.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: David Hubbard <david.c.hubbard@gmail.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Ferre [Tue, 15 Dec 2009 02:01:31 +0000 (18:01 -0800)]
mmc: atmel-mci: new MCI2 module support in atmel-mci driver
This new revision of the IP adds some improvements to the MCI already
present in several Atmel SOC.
Some new registers are added and a particular way of handling DMA
interaction lead to a new sequence in function call which is backward
compatible: On MCI2, we must set the DMAEN bit to enable the DMA
handshaking interface. This must happen before the data transfer command
is sent.
A new function is able to differentiate MCI2 code and is based on
knowledge of processor id (cpu_is_xxx()).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Ferre [Tue, 15 Dec 2009 02:01:30 +0000 (18:01 -0800)]
atmel-mci: change use of dma slave interface
Allow the use of another DMA controller driver in atmel-mci sd/mmc driver.
This adds a generic dma_slave pointer to the mci platform structure where
we can store DMA controller information. In atmel-mci we use information
provided by this structure to initialize the driver (with new helper
functions that are architecture dependant).
This also adds at32/avr32 chip modifications to cope with this new access
method.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Hutchings [Tue, 15 Dec 2009 02:01:29 +0000 (18:01 -0800)]
mmc: add module parameter to set whether cards are assumed removable
Some people run general-purpose distribution kernels on netbooks with
a card that is physically non-removable or logically non-removable
(e.g. used for /home) and cannot be cleanly unmounted during suspend.
Add a module parameter to set whether cards are assumed removable or
non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME.
In general, it is not possible to tell whether a card present in an MMC
slot after resume is the same that was there before suspend. So there are
two possible behaviours, each of which will cause data loss in some cases:
CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed
during suspend. Any filesystem on them must be unmounted before suspend;
otherwise, buffered writes will be lost.
CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during
suspend. They must not be swapped during suspend; otherwise, buffered
writes will be flushed to the wrong card.
Currently the choice is made at compile time and this allows that to be
overridden at module load time.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 15 Dec 2009 02:01:27 +0000 (18:01 -0800)]
s3cmci: convert missed s3c2410_gpio calls to gpiolib calls
Convert two missed s3c2410 specific gpio calls to gpiolib calls.
Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Simtec Linux Team <linux@simtec.co.uk> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicolas Pitre [Tue, 15 Dec 2009 02:01:26 +0000 (18:01 -0800)]
sdhci: add support for the SysKonnect CardBus2SDIO adapter
This is still in use especially to develop SDIO device drivers on laptop
machines which are lacking SDIO slots. This adapter supports SDIO cards
only due to lack of 136-bit response capability.
Signed-off-by: Nicolas Pitre <nico@marvell.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mmc: davinci: modify data types of EDMA related variables
Currently DaVinci EDMA driver supports multiple EDMA channel controller
instances. edma_alloc_channel() api returns a 32 bit value which has the
channel controller number in MSB and the EDMA channel number in LSB. The
variables which store the value returned by edma_alloc_channel() have to
be 32 bit wide now.
Albert Herranz [Tue, 15 Dec 2009 02:01:19 +0000 (18:01 -0800)]
sdio: rework cis tuple parsing
Rework the current CIS tuple parsing code, reusing the existing
infrastructure and providing an easy way to add new CISTPL_FUNCE parsers
by TPLFE_TYPE.
Valid known CIS tuples are now silently queued for the SDIO function
driver when not parsed/processed (-EILSEQ) by the SDIO core. Unknown CIS
tuples (-ENOENT) are queued too for the SDIO function driver without
aborting the initialization, but emit a warning in the kernel log.
CISTPL_FUNCE tuples can be "whitelisted" now by adding a matching entry to
the cis_tpl_funce_list table.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es> Acked-by: Pierre Ossman <pierre@ossman.eu> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Tue, 15 Dec 2009 02:01:16 +0000 (18:01 -0800)]
firmware: only allow EDD on x86
Rather than have the EDD depend on !ia64 (and assuming that only ia64,
x86, x86_64 will be including this Kconfig), have EDD depend on the only
arches which can support this code. This should allow all other arches to
cleanly include the firmware Kconfig.
Also simplify the x86 string used by FIRMWARE_MEMMAP to match EDD.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Matt Domsch <Matt_Domsch@dell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently, We marked strstrip() as must_check. because it was frequently
misused and it should be checked. However, we found one exception.
scsi/ipr.c intentionally ignore return value of strstrip. Because it
wishes to keep the whitespace at the beginning.
Thus we need to keep with and without checked whitespace trim function.
This patch adds a new strim() and changes ipr.c to use it.
[akpm@linux-foundation.org: coding-style fixes] Suggested-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Tue, 15 Dec 2009 02:01:12 +0000 (18:01 -0800)]
drivers/md/md.c: use %pU to print UUIDs
Signed-off-by: Joe Perches <joe@perches.com> Cc: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Tue, 15 Dec 2009 02:01:10 +0000 (18:01 -0800)]
fs/xfs/xfs_log_recover.c: use %pU to print UUIDs
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Alex Elder <aelder@sgi.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No functional change. Cache strlen() result to avoid recalculating it up
to 3 times on the worst case.
Reduces code size a little by 32 bytes:
text data bss dec hex filename
1385 0 0 1385 569 lib/parser.o-BEFORE
1353 0 0 1353 549 lib/parser.o-AFTER
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tree-wide: convert open calls to remove spaces to skip_spaces() lib function
Makes use of skip_spaces() defined in lib/string.c for removing leading
spaces from strings all over the tree.
It decreases lib.a code size by 47 bytes and reuses the function tree-wide:
text data bss dec hex filename
64688 584 592 65864 10148 (TOTALS-BEFORE)
64641 584 592 65817 10119 (TOTALS-AFTER)
Also, while at it, if we see (*str && isspace(*str)), we can be sure to
remove the first condition (*str) as the second one (isspace(*str)) also
evaluates to 0 whenever *str == 0, making it redundant. In other words,
"a char equals zero is never a space".
Julia Lawall tried the semantic patch (http://coccinelle.lip6.fr) below,
and found occurrences of this pattern on 3 more files:
drivers/leds/led-class.c
drivers/leds/ledtrig-timer.c
drivers/video/output.c
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Cc: Julia Lawall <julia@diku.dk> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Neil Brown <neilb@suse.de> Cc: Kyle McMartin <kyle@mcmartin.ca> Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: David Howells <dhowells@redhat.com> Cc: <linux-ext4@vger.kernel.org> Cc: Samuel Ortiz <samuel@sortiz.org> Cc: Patrick McHardy <kaber@trash.net> Cc: Takashi Iwai <tiwai@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
string: on strstrip(), first remove leading spaces before running over str
... so that strlen() iterates over a smaller string comprising of the
remaining characters only.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
string: factorize skip_spaces and export it to be generally available
On the following sentence:
while (*s && isspace(*s))
s++;
If *s == 0, isspace() evaluates to ((_ctype[*s] & 0x20) != 0), which
evaluates to ((0x08 & 0x20) != 0) which equals to 0 as well.
If *s == 1, we depend on isspace() result anyway. In other words,
"a char equals zero is never a space", so remove this check.
Also, *s != 0 is most common case (non-null string).
Fixed const return as noticed by Jan Engelhardt and James Bottomley.
Fixed unnecessary extra cast on strstrip() as noticed by Jan Engelhardt.
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 15 Dec 2009 02:01:02 +0000 (18:01 -0800)]
drivers/scsi/sym53c8xx_2/sym_glue.c: rename skip_spaces() to sym_skip_spaces()
To avoid a collision with the newly-added kernel-wide skip_spaces().
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vsprintf: reuse almost identical simple_strtoulX() functions
The difference between simple_strtoul() and simple_strtoull() is just
the size of the variable used to keep track of the sum of characters
converted to numbers:
unsigned long simple_strtoul() {...}
unsigned long long simple_strtoull(){...}
Both are same size on my Core 2/gcc 4.4.1.
Overflow condition is not checked on both functions, so an extremely large
string can break these functions so that they don't even notice it.
As we do not care for overflowing on these functions, always keep the sum
using the larger variable around (unsigned long long) on simple_strtoull()
and cast it to (unsigned long) on simple_strtoul(), which then becomes
just a wrapper around simple_strtoull().
Code size decreases by 304 bytes:
text data bss dec hex filename
15534 0 8 15542 3cb6 vsprintf.o (ex lib/lib.a-BEFORE)
15230 0 8 15238 3b86 vsprintf.o (ex lib/lib.a-AFTER)
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vsprintf: factor out skip_space code in a separate function
When converting more caller sites, the inline decision will be left up to gcc.
It decreases code size:
text data bss dec hex filename
15710 0 8 15718 3d66 vsprintf.o (ex lib/lib.a-BEFORE)
15534 0 8 15542 3cb6 vsprintf.o (ex lib/lib.a-AFTER)
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vsprintf: reduce code size by avoiding extra check
No functional change, just refactor the code so that it avoid checking
"if (hi)" two times in a sequence, taking advantage of previous check made.
It also reduces code size:
text data bss dec hex filename
15726 0 8 15734 3d76 vsprintf.o (ex lib/lib.a-BEFORE)
15710 0 8 15718 3d66 vsprintf.o (ex lib/lib.a-AFTER)
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It decreases code size as well:
text data bss dec hex filename
15758 0 8 15766 3d96 vsprintf.o (ex lib/lib.a-BEFORE)
15726 0 8 15734 3d76 vsprintf.o (ex lib/lib.a-TOLOWER)
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset reduces lib/lib.a code size by 482 bytes on my Core 2 with
gcc 4.4.1 even considering that it exports a newly defined function
skip_spaces() to drivers:
text data bss dec hex filename
64867 840 592 66299 102fb (TOTALS-lib.a-BEFORE)
64641 584 592 65817 10119 (TOTALS-lib.a-AFTER)
and implements some code tidy up.
Besides reducing lib.a size, it converts many in-tree drivers to use the
newly defined function, which makes another small reduction on kernel size
overall when those drivers are used.
This patch:
Change "<NULL>" to "(null)", unifying 3 equal strings.
glibc also uses "(null)" for the same purpose.
It decreases code size by 7 bytes:
text data bss dec hex filename
15765 0 8 15773 3d9d vsprintf.o (ex lib/lib.a-BEFORE)
15758 0 8 15766 3d96 vsprintf.o (ex lib/lib.a-AFTER)
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Tue, 15 Dec 2009 02:00:54 +0000 (18:00 -0800)]
MAINTAINERS: Update file patterns for WOLFSON MICROELECTRONICS PMIC DRIVERS
One of the includes pointed to a non-existent directory
Add Documentation/hwmon/wm83??
Add sound/soc/codecs/wm(8350|8400).h files
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Tue, 15 Dec 2009 02:00:52 +0000 (18:00 -0800)]
MAINTAINERS: rename PALM TREO section and file patterns
Signed-off-by: Joe Perches <joe@perches.com> Cc: Tomas Cech <sleep_walker@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KOSAKI Motohiro [Tue, 15 Dec 2009 02:00:52 +0000 (18:00 -0800)]
MAINTAINERS: mark cifs mailing list as "moderated for non-subscribers"
If non-subscribers post bug report to CIFS mailing list, they will get
following messages.
Your mail to 'linux-cifs-client' with the subject
[PATCH x/x] cifs: xxxxxxxxxxxxx
Is being held until the list moderator can review it for approval.
The reason it is being held:
Post by non-member to a members-only list
Either the message will get posted to the list, or you will receive
notification of the moderator's decision. If you would like to cancel
this posting, please visit the following URL:
members-only list should be written as so in MAINTAINERS file.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Steve French <sfrench@samba.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>