This moves the lock_kernel() call from soundcore_open
to the individual OSS device drivers, where we can deal
with it one driver at a time if needed, or just kill
off the drivers.
All core components in ALSA already provide
adequate locking in their open()-functions
and do not require the big kernel lock, so
there is no need to add the BKL there.
Clemens Ladisch [Mon, 12 Jul 2010 14:27:24 +0000 (16:27 +0200)]
ALSA: via82xx: allow changing the initial DXS volume
As per-stream volume controls, the DXS controls are not intended to
adjust the overall sound level and so are initialized every time
a stream is opened. However, there are special situations where one
wants to reduce the overall volume in the digital domain, i.e., before
the AC'97 codec's PCM volume control. To allow this, add a module
parameter that sets the initial DXS volume.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Tested-by: Soeren D. Schulze <soeren.d.schulze@gmx.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Thu, 8 Jul 2010 14:38:01 +0000 (16:38 +0200)]
ALSA: usb-audio: silence a superfluous warning
It is not advisable to print a warning when a device does not support
setting the sample rate because this is perfectly valid for devices with
a single rate or where rates are implicitly changed by selecting another
alternate setting.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
John Kacur [Sat, 3 Jul 2010 22:02:31 +0000 (00:02 +0200)]
soundcore_open: Reduce the area BKL coverage
Most of this function is protected by the sound_loader_lock.
We can push down the BKL to this call out err = file->f_op->open(inode,file);
In order to build the sound core without the BKL, we
will need to push the lock_kernel() call into the ~20
device drivers that register their file operations.
Signed-off-by: John Kacur <jkacur@redhat.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
David Dillow [Sat, 26 Jun 2010 22:04:32 +0000 (00:04 +0200)]
sis7019: fix capture issues with multiple periods per buffer
When using a timing voice to clock out periods during capture, the
driver would slowly loose synchronization and never catch up, eventually
reaching a point where it no longer generated interrupts. To avoid
this situation, the virtual period clocking was changed to shorten the
next timing period when our timing voice falls too far behind the
capture voice. In addition, the first virtual period for the timing
voice was slightly too short, causing the timing voice to initially be
ahead of the capture voice.
While tracking down this problem, I noticed that the expected sample
offset was being incorrectly initialized, causing an overrun to be
incorrectly reported when the timing voice happened to be perfectly
synchronized.
Reported-by: Hans Schou <linux@schou.dk> Signed-off-by: Dave Dillow <dave@thedillows.org> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
David Dillow [Sat, 26 Jun 2010 22:13:20 +0000 (00:13 +0200)]
ALSA: pcm_lib: avoid timing jitter in snd_pcm_read/write()
When using poll() to wait for the next period -- or avail_min samples --
one gets a consistent delay for each system call that is usually just a
little short of the selected period time. However, When using
snd_pcm_read/write(), one gets a jittery delay that alternates between
less than a millisecond and approximately two period times. This is
caused by snd_pcm_lib_{read,write}1() transferring any available samples
to the user's buffer and adjusting the application pointer prior to
sleeping to the end of the current period. When the next period
interrupt occurs, there is then less than avail_min samples remaining to
be transferred in the period, so we end up sleeping until a second
period occurs.
This is solved by using runtime->twake as the number of samples needed
for a wakeup in addition to selecting the proper wait queue to wake in
snd_pcm_update_state(). This requires twake to be non-zero when used
by snd_pcm_lib_{read,write}1() even if avail_min is zero.
Signed-off-by: Dave Dillow <dave@thedillows.org> Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Daniel Mack [Wed, 16 Jun 2010 15:57:31 +0000 (17:57 +0200)]
ALSA: usb-audio: simplify control interface access
As the control interface is now carried in struct snd_usb_audio, we can
simplify the API a little and also drop the private ctrlif field from
struct usb_mixer_interface.
Also remove a left-over function prototype in pcm.h.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alexey Fisher [Wed, 23 Jun 2010 12:17:09 +0000 (14:17 +0200)]
ALSA: usb-audio - Add volume resolution quirk for some Logitech webcams
Some programs like Skype trying to set capture volume automatically.
Normally it will tray, carefully step by step lover or higher, set the volume.
In real word it work not really well, because devises and vendors lie about
real audio settings.
For example most Logitech webcams have 6400 or 3500 steps for capture volume.
They do not tell that actual resolution is 384. So we have only 7 or 18 real
steps. In this patch I set real resolution only for tested devices.
Jiri Slaby [Mon, 21 Jun 2010 15:03:21 +0000 (17:03 +0200)]
ALSA: usb/endpoint, fix dangling pointer use
Stanse found that in snd_usb_parse_audio_endpoints, there is a
dangling pointer dereference. When snd_usb_parse_audio_format fails,
fp is freed, and continue invoked. On the next loop, there is
"fp && fp->altsetting == 1 && fp->channels == 1" test, but fp is set
from the last iteration (but is bogus) and thus ilegally dereferenced.
Daniel Mack [Fri, 11 Jun 2010 15:34:22 +0000 (17:34 +0200)]
ALSA: usb-audio: fix UAC2 control value queries
For RANGE requests, we should only query as much bytes as we're in fact
interested in.
For CUR requests, we shouldn't confuse the firmware with an overlong
request but just ask for 2 bytes.
This might need fixing in the future as it's not entirely clear when to
dispatch 1-byte, 2-byte and 4-byte request blocks. For now, we assume
everything is coded in 16bit - this works for all firmware
implementations I've seen.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Reported-by: Alex Lee <alexlee188@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
A device may report its supported sample rates in ranges rather than in
discrete triplets. The code used to only parse the MIN field instead of
properly paying attention to the MAX and RES values.
Also, handle RES values of 1 correctly and announce a continous sample
rate range in this case.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Reported-by: Alex Lee <alexlee188@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Daniel Mack [Fri, 11 Jun 2010 15:34:20 +0000 (17:34 +0200)]
ALSA: usb-audio: fix control messages for USB_RECIP_INTERFACE
Control messages directed to an interface must have the interface number
set in the lower 8 bits of wIndex. This wasn't done correctly for some
clock and mixer messages.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Reported-by: Alex Lee <alexlee188@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Chris Wilson [Wed, 2 Jun 2010 07:30:48 +0000 (08:30 +0100)]
drm/i915: Move non-phys cursors into the GTT
Cursors need to be in the GTT domain when being accessed by the GPU.
Previously this was a fortuitous byproduct of userspace using pwrite()
to upload the image data into the cursor. The redundant clflush was
removed in commit 9b8c4a and so the image was no longer being flushed
out of the caches into main memory. One could also devise a scenario
where the cursor was rendered by the GPU, prior to being attached as the
cursor, resulting in similar corruption due to the missing MI_FLUSH.
Fixes:
Bug 28335 - Cursor corruption caused by commit 9b8c4a0b21
https://bugs.freedesktop.org/show_bug.cgi?id=28335
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com> Tested-by: Linus Torvalds <torvalds@linux-foundation.org> Reported-by: Andy Isaacson <adi@hexapodia.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 5 Jun 2010 14:33:05 +0000 (07:33 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: improve xfs_isilocked
xfs: skip writeback from reclaim context
xfs: remove done roadmap item from xfs-delayed-logging-design.txt
xfs: fix race in inode cluster freeing failing to stale inodes
xfs: fix access to upper inodes without inode64
xfs: fix might_sleep() warning when initialising per-ag tree
fs/xfs/quota: Add missing mutex_unlock
xfs: remove duplicated #include
xfs: convert more trace events to DEFINE_EVENT
xfs: xfs_trace.c: remove duplicated #include
xfs: Check new inode size is OK before preallocating
xfs: clean up xlog_align
xfs: cleanup log reservation calculactions
xfs: be more explicit if RT mount fails due to config
xfs: replace E2BIG with EFBIG where appropriate
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
X25: remove duplicated #include
tcp: use correct net ns in cookie_v4_check()
rps: tcp: fix rps_sock_flow_table table updates
ppp_generic: fix multilink fragment sizes
syncookies: remove Kconfig text line about disabled-by-default
ixgbe: only check pfc bits in hang logic if pfc is enabled
net: check for refcount if pop a stacked dst_entry
ixgbe: return IXGBE_ERR_RAR_INDEX when out of range
act_pedit: access skb->data safely
sfc: Store port number in net_device::dev_id
epic100: Test __BIG_ENDIAN instead of (non-existent) CONFIG_BIG_ENDIAN
tehuti: return -EFAULT on copy_to_user errors
isdn/kcapi: return -EFAULT on copy_from_user errors
e1000e: change logical negate to bitwise
sfc: Get port number from CS_PORT_NUM, not PCI function number
cls_u32: use skb_header_pointer() to dereference data safely
TCP: tcp_hybla: Fix integer overflow in slow start increment
act_nat: fix the wrong checksum when addr isn't in old_addr/mask
net/fec: fix pm to survive to suspend/resume
korina: count RX DMA OVR as rx_fifo_error
...
Linus Torvalds [Sat, 5 Jun 2010 14:31:13 +0000 (07:31 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: remove obsolete declarations of cache constructor and destructor
nilfs2: fix style issue in nilfs_destroy_cachep
Linus Torvalds [Sat, 5 Jun 2010 04:12:39 +0000 (21:12 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
Minix: Clean up left over label
fix truncate inode time modification breakage
fix setattr error handling in sysfs, configfs
fcntl: return -EFAULT if copy_to_user fails
wrong type for 'magic' argument in simple_fill_super()
fix the deadlock in qib_fs
mqueue doesn't need make_bad_inode()
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
module: fix bne2 "gave up waiting for init of module libcrc32c"
module: verify_export_symbols under the lock
module: move find_module check to end
module: make locking more fine-grained.
module: Make module sysfs functions private.
module: move sysfs exposure to end of load_module
module: fix kdb's illicit use of struct module_use.
module: Make the 'usage' lists be two-way
Rusty Russell [Sat, 5 Jun 2010 17:17:37 +0000 (11:17 -0600)]
module: fix bne2 "gave up waiting for init of module libcrc32c"
Problem: it's hard to avoid an init routine stumbling over a
request_module these days. And it's not clear it's always a bad idea:
for example, a module like kvm with dynamic dependencies on kvm-intel
or kvm-amd would be neater if it could simply request_module the right
one.
If another module is waiting inside resolve_symbol() for libcrc32c to
finish initializing (ie. bne2 depends on libcrc32c) then it does so
holding the module lock, and our request_module() can't make progress
until that is released.
Waiting inside resolve_symbol() without the lock isn't all that hard:
we just need to pass the -EBUSY up the call chain so we can sleep
where we don't hold the lock. Error reporting is a bit trickier: we
need to copy the name of the unfinished module before releasing the
lock.
Other notes:
1) This also fixes a theoretical issue where a weak dependency would allow
symbol version mismatches to be ignored.
2) We rename use_module to ref_module to make life easier for the only
external user (the out-of-tree ksplice patches).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Tim Abbot <tabbott@ksplice.com> Tested-by: Brandon Philips <bphilips@suse.de>
Rusty Russell [Sat, 5 Jun 2010 17:17:37 +0000 (11:17 -0600)]
module: verify_export_symbols under the lock
It disabled preempt so it was "safe", but nothing stops another module
slipping in before this module is added to the global list now we don't
hold the lock the whole time.
So we check this just after we check for duplicate modules, and just
before we put the module in the global list.
(find_symbol finds symbols in coming and going modules, too).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Linus Torvalds [Sat, 5 Jun 2010 17:17:36 +0000 (11:17 -0600)]
module: move find_module check to end
I think Rusty may have made the lock a bit _too_ finegrained there, and
didn't add it to some places that needed it. It looks, for example, like
PATCH 1/2 actually drops the lock in places where it's needed
("find_module()" is documented to need it, but now load_module() didn't
hold it at all when it did the find_module()).
Rather than adding a new "module_loading" list, I think we should be able
to just use the existing "modules" list, and just fix up the locking a
bit.
In fact, maybe we could just move the "look up existing module" a bit
later - optimistically assuming that the module doesn't exist, and then
just undoing the work if it turns out that we were wrong, just before
adding ourselves to the list.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Sat, 5 Jun 2010 17:17:36 +0000 (11:17 -0600)]
module: move sysfs exposure to end of load_module
This means a little extra work, but is more logical: we don't put
anything in sysfs until we're about to put the module into the
global list an parse its parameters.
This also gives us a logical place to put duplicate module detection
in the next patch.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rusty Russell [Sat, 5 Jun 2010 17:17:35 +0000 (11:17 -0600)]
module: fix kdb's illicit use of struct module_use.
Linus changed the structure, and luckily this didn't compile any more.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Martin Hicks <mort@sgi.com>
Linus Torvalds [Mon, 31 May 2010 19:19:37 +0000 (12:19 -0700)]
module: Make the 'usage' lists be two-way
When adding a module that depends on another one, we used to create a
one-way list of "modules_which_use_me", so that module unloading could
see who needs a module.
It's actually quite simple to make that list go both ways: so that we
not only can see "who uses me", but also see a list of modules that are
"used by me".
In fact, we always wanted that list in "module_unload_free()": when we
unload a module, we want to also release all the other modules that are
used by that module. But because we didn't have that list, we used to
first iterate over all modules, and then iterate over each "used by me"
list of that module.
By making the list two-way, we simplify module_unload_free(), and it
allows for some trivial fixes later too.
Eric Dumazet [Thu, 3 Jun 2010 09:03:58 +0000 (09:03 +0000)]
rps: tcp: fix rps_sock_flow_table table updates
I believe a moderate SYN flood attack can corrupt RFS flow table
(rps_sock_flow_table), making RPS/RFS much less effective.
Even in a normal situation, server handling short lived sessions suffer
from bad steering for the first data packet of a session, if another SYN
packet is received for another session.
We do following action in tcp_v4_rcv() :
sock_rps_save_rxhash(sk, skb->rxhash);
We should _not_ do this if sk is a LISTEN socket, as about each
packet received on a LISTEN socket has a different rxhash than
previous one.
-> RPS_NO_CPU markers are spread all over rps_sock_flow_table.
Also, it makes sense to protect sk->rxhash field changes with socket
lock (We currently can change it even if user thread owns the lock
and might use rxhash)
This patch moves sock_rps_save_rxhash() to a sock locked section,
and only for non LISTEN sockets.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 3 Jun 2010 17:03:45 +0000 (17:03 +0000)]
ixgbe: only check pfc bits in hang logic if pfc is enabled
Only check pfc bits in hang logic if PFC is enabled. Previously,
if DCB was enabled but PFC was disabled the incorrect pause
bits would be checked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: check for refcount if pop a stacked dst_entry
xfrm triggers a warning if dst_pop() drops a refcount
on a noref dst. This patch changes dst_pop() to
skb_dst_pop(). skb_dst_pop() drops the refcnt only
on a refcounted dst. Also we don't clone the child
dst_entry, so it is not refcounted and we can use
skb_dst_set_noref() in xfrm_output_one().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Make intc messages consistent via pr_fmt.
sh: make sure static declaration on ms7724se
sh: make sure static declaration on mach-migor
sh: make sure static declaration on mach-ecovec24
sh: make sure static declaration on mach-ap325rxa
clocksource: sh_cmt: compute mult and shift before registration
clocksource: sh_tmu: compute mult and shift before registration
sh: PIO disabling for x3proto and urquell.
sh: mach-sdk7786: conditionally disable PIO support.
sh: support for platforms without PIO.
usb: r8a66597-hcd pio to mmio accessor conversion.
usb: gadget: r8a66597-udc pio to mmio accessor conversion.
usb: gadget: m66592-udc pio to mmio accessor conversion.
sh: add romImage MMCIF boot for sh7724 and Ecovec V2
sh: add boot code to MMCIF driver header
sh: prepare MMCIF driver header file
sh: allow romImage data between head.S and the zero page
sh: Add support MMCIF for ecovec
sh: remove duplicated #include
input: serio: disable i8042 for non-cayman sh platforms.
...
Linus Torvalds [Fri, 4 Jun 2010 22:39:54 +0000 (15:39 -0700)]
Merge branch 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core: (83 commits)
i7core_edac: Better describe the supported devices
Add support for Westmere to i7core_edac driver
i7core_edac: don't free on success
i7core_edac: Add support for X5670
Always call i7core_[ur]dimm_check_mc_ecc_err
i7core_edac: fix memory leak of i7core_dev
EDAC: add __init to i7core_xeon_pci_fixup
i7core_edac: Fix wrong device id for channel 1 devices
i7core: add support for Lynnfield alternate address
i7core_edac: Add initial support for Lynnfield
i7core_edac: do not export static functions
edac: fix i7core build
edac: i7core_edac produces undefined behaviour on 32bit
i7core_edac: Use a more generic approach for probing PCI devices
i7core_edac: PCI device is called NONCORE, instead of NOCORE
i7core_edac: Fix ringbuffer maxsize
i7core_edac: First store, then increment
i7core_edac: Better parse "any" addrmask
i7core_edac: Use a lockless ringbuffer
edac: Create an unique instance for each kobj
...
Linus Torvalds [Fri, 4 Jun 2010 22:37:44 +0000 (15:37 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (27 commits)
block: make blk_init_free_list and elevator_init idempotent
block: avoid unconditionally freeing previously allocated request_queue
pipe: change /proc/sys/fs/pipe-max-pages to byte sized interface
pipe: change the privilege required for growing a pipe beyond system max
pipe: adjust minimum pipe size to 1 page
block: disable preemption before using sched_clock()
cciss: call BUG() earlier
Preparing 8.3.8rc2
drbd: Reduce verbosity
drbd: use drbd specific ratelimit instead of global printk_ratelimit
drbd: fix hang on local read errors while disconnected
drbd: Removed the now empty w_io_error() function
drbd: removed duplicated #includes
drbd: improve usage of MSG_MORE
drbd: need to set socket bufsize early to take effect
drbd: improve network latency, TCP_QUICKACK
drbd: Revert "drbd: Create new current UUID as late as possible"
brd: support discard
Revert "writeback: fix WB_SYNC_NONE writeback from umount"
Revert "writeback: ensure that WB_SYNC_NONE writeback with sb pinned is sync"
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: add support for various Titan PCI cards
vt_ioctl: return -EFAULT on copy_from_user errors
serial: altera_uart: Proper section for altera_uart_remove
tty: fix a little bug in scrup, vt.c
altera_uart: Simplify altera_uart_console_putc
altera_uart: Don't take spinlock in already protected functions
TTY/n_gsm: potential double lock
serial: bfin_5xx: fix typo in IER check
serial: bfin_5xx: IRDA is not affected by anomaly 05000230
serial_cs: add and sort IDs for serial and modem cards
msm_serial: fix serial on trout
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: unbind all interfaces before rebinding them
USB: serial: digi_acceleport: Eliminate a NULL pointer dereference
usb: fix ehci_hcd build failure when both generic-OF and xilinx is selected
USB: cdc-acm: fix resource reclaim in error path of acm_probe
USB: ftdi_sio: fix DTR/RTS line modes
USB: s3c-hsotg: Ensure FIFOs are fully flushed after layout
USB: s3c-hsotg: SoftDisconnect minimum 3ms
USB: s3c-hsotg: Ensure TX FIFO addresses setup when initialising FIFOs
USB: s3c_hsotg: define USB_GADGET_DUALSPEED in Kconfig
USB: s3c: Enable soft disconnect during initialization
USB: xhci: Print NEC firmware version.
USB: xhci: Wait for host to start running.
USB: xhci: Wait for controller to be ready after reset.
USB: isp1362: fix inw warning on Blackfin systems
USB: mos7840: fix null-pointer dereference
Cory Maccarrone [Fri, 4 Jun 2010 21:15:07 +0000 (14:15 -0700)]
omap: remove BUG_ON for disabled interrupts
Remove a BUG_ON for when interrupts are disabled during an MMC request.
During boot, interrupts can be disabled when a request is made, causing
this bug to be triggered. In reality, there's no reason this should halt
the kernel, as the driver has proved reliable in spite of disabled
interrupts, and additionally, there's nothing in this code that would
require interrupts to be enabled.
The only setup I've managed to make it trigger on is on the HTC Herald
during bootup when the driver is built into the kernel (mostly because
that's all I have). I believe it's related to the fact that on bootup I
get many timeout errors on "CMD5" while initializing the card. Each CMD5
timeout triggers that bug (I changed it to a WARN_ON to get it to boot in)
due to the fact that part of the timeout code involves sending the request
again. With interrupts turned off, that BUG would be triggered.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page allocator: smarter retry of costly-order allocations
Original intention was "return success if the system have shrinkable zones
though priority==0 reclaim was failure". But the above patch changed to
"return nr_reclaimed if .....". Oh, That forgot nr_reclaimed may be 0 if
priority==0 reclaim failure.
And Johannes's patch 0aeb2339e54e ("vmscan: remove all_unreclaimable scan
control") made it more corrupt. Originally, priority==0 reclaim failure
on memcg return 0, but this patch changed to return 1. It totally
confused memcg.
Akinobu Mita [Fri, 4 Jun 2010 21:15:04 +0000 (14:15 -0700)]
kernel/: fix BUG_ON checks for cpu notifier callbacks direct call
The commit 80b5184cc537718122e036afe7e62d202b70d077 ("kernel/: convert cpu
notifier to return encapsulate errno value") changed the return value of
cpu notifier callbacks.
Those callbacks don't return NOTIFY_BAD on failures anymore. But there
are a few callbacks which are called directly at init time and checking
the return value.
I forgot to change BUG_ON checking by the direct callers in the commit.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Child groups should have a greater depth than their parents. Prior to
this change, the parent would incorrectly report zero memory usage for
child cgroups when use_hierarchy is enabled.
test script:
mount -t cgroup none /cgroups -o memory
cd /cgroups
mkdir cg1
Using fae9c79, a recent patch that changed alloc_css_id() depth computation,
the parent incorrectly reports zero usage:
root@ubuntu:~# ./test
1+0 records in
1+0 records out 1048576 bytes (1.0 MB) copied, 0.0151844 s, 69.1 MB/s
With this patch, the parent correctly includes child usage:
root@ubuntu:~# ./test
1+0 records in
1+0 records out 1048576 bytes (1.0 MB) copied, 0.0136827 s, 76.6 MB/s
Commit f601441916d1e19291d0b4f044b4a7551e2924d0 ("imxfb: add support for
i.MX25:) has inserted the symbol HAVE_FB_IMX, which does not depend on FB
after the menuconfig FB. This breaks the menu, presenting most of the
drivers outside of it, when using menuconfig.
Moving the symbol to the start of the file, just like HAVE_FB_ATMEL, fixes
the problem without breaking it for iMX25 configurations (tested with
ARCH=arm, no build).
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Baruch Siach <baruch@tkos.co.il> Cc: "David S. Miller" <davem@davemloft.net> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/um: fix kunmap_atomic() call in skas/uaccess.c
kunmap_atomic() takes a pointer to within the page, not the struct page.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Fri, 4 Jun 2010 21:14:58 +0000 (14:14 -0700)]
sys_personality: change sys_personality() to accept "unsigned int" instead of u_long
task_struct->pesonality is "unsigned int", but sys_personality() paths use
"unsigned long pesonality". This means that every assignment or
comparison is not right. In particular, if this argument does not fit
into "unsigned int" __set_personality() changes the caller's personality
and then sys_personality() returns -EINVAL.
Turn this argument into "unsigned int" and avoid overflows. Obviously,
this is the user-visible change, we just ignore the upper bits. But this
can't break the sane application.
There is another thing which can confuse the poorly written applications.
User-space thinks that this syscall returns int, not long. This means
that the returned value can be negative and look like the error code. But
note that libc won't be confused and thus errno won't be set, and with
this patch the user-space can never get -1 unless sys_personality() really
fails. And, most importantly, the negative RET != -1 is only possible if
that app previously called personality(RET).
Although the fix provided is correct, it's been suggested to avoid the
underlying race in the same way as it is currently done in filesystems
like NFS, for maintainability.
A following patch "fb_defio: redo fix for non-dirty ptes" will provide
such an alternate fix.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es> Cc: Jaya Kumar <jayakumar.lkml@gmail.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Fri, 4 Jun 2010 21:14:55 +0000 (14:14 -0700)]
flat: fix unmap len in load error path
The data chunk is mmaped with 'len' which remains unchanged, so use that
when unmapping in the error path rather than trying to recalculate (and
incorrectly so) the value used originally.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: David McCullough <davidm@snapgear.com> Acked-by: Greg Ungerer <gerg@uclinux.org> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Michal Simek <monstr@monstr.eu> Cc: Hirokazu Takata <takata@linux-m32r.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Fri, 4 Jun 2010 21:14:53 +0000 (14:14 -0700)]
fs/binfmt_flat.c: split the stack & data alignments
The stack and data have different alignment requirements, so don't force
them to wear the same shoe. Increase the data alignment to match that
which the elf2flt linker script has always been using: 0x20 bytes. Not
only does this bring the kernel loader in line with the toolchain, but it
also fixes a swath of gcc tests which try to force larger alignment values
but randomly fail when the FLAT loader fails to deliver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: David Woodhouse <David.Woodhouse@intel.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Acked-by: David McCullough <davidm@snapgear.com> Acked-by: Greg Ungerer <gerg@uclinux.org> Cc: Paul Mundt <lethal@linux-sh.org> Tested-by: Michal Simek <monstr@monstr.eu> Cc: Hirokazu Takata <takata@linux-m32r.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Jie Zhang <jie@codesourcery.com> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dmitry Torokhov [Fri, 4 Jun 2010 21:14:52 +0000 (14:14 -0700)]
vmware balloon: clamp number of collected non-balloonable pages
Limit number of accumulated non-balloonable pages during inflation cycle,
otherwise there is a chance we will be spinning and growing the list
forever. This happens during torture tests when balloon target changes
while we are in the middle of inflation cycle and monitor starts refusing
to lock pages (since they are not needed anymore).
Nick Piggin [Fri, 4 Jun 2010 21:14:51 +0000 (14:14 -0700)]
xtensa: invoke oom-killer from page fault
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: David Rientjes <rientjes@google.com> Cc: Chris Zankel <chris@zankel.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Fri, 4 Jun 2010 21:14:51 +0000 (14:14 -0700)]
mn10300: invoke oom-killer from page fault
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: David Rientjes <rientjes@google.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Fri, 4 Jun 2010 21:14:49 +0000 (14:14 -0700)]
m32r: invoke oom-killer from page fault
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: David Rientjes <rientjes@google.com> Cc: Hirokazu Takata <takata@linux-m32r.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Fri, 4 Jun 2010 21:14:49 +0000 (14:14 -0700)]
frv: invoke oom-killer from page fault
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: David Howells <dhowells@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>