Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Acked-by: Greg Rose <greg.v.rose@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Thu, 28 Oct 2010 00:59:57 +0000 (00:59 +0000)]
ixgbe: DCB, fix TX hang occurring in stress condition with PFC
The DCB credits refill quantum _must_ be greater than half the max
packet size. This is needed to guarantee that TX DMA operations
are not attempted during a pause state. Additionally, the min IFG
must be set correctly for DCB mode. If a DMA operation is
requested unexpectedly during the pause state the HW data
store may be corrupted leading to a DMA hang. The DMA hang
requires a reset to correct. This fixes the HW configuration
to avoid this condition.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Carolyn Wyborny [Thu, 28 Oct 2010 00:59:55 +0000 (00:59 +0000)]
e1000e: Add check for reset flags before displaying reset message
Some parts need to execute resets during normal operation. This flag
check ensures that those parts reset without needlessly alarming the
user. Other unexpected resets by other parts will dump debug info
and message the reset action to the user, as originally intended.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Carolyn Wyborny [Thu, 28 Oct 2010 00:59:53 +0000 (00:59 +0000)]
e1000e: reset PHY after errors detected
Some errors can be induced in the PHY via environmental testing
(specifically extreme temperature changes and electro static
discharge testing), and in the case of the PHY hanging due to
this input, this detects the problem and resets to continue.
This issue only applies to 82574 silicon.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Tue, 26 Oct 2010 14:56:03 +0000 (14:56 +0000)]
igb: Fix unused variable warning.
Commit eab6d18d "vlan: Don't check for vlan group before
vlan_tx_tag_present" removed the need for the adapter variable
in igb_xmit_frame_ring_adv(). This removes the variable as well
to avoid the compiler warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Wed, 27 Oct 2010 08:45:14 +0000 (08:45 +0000)]
ehea: Fixing statistics
(Applied over Eric's "ehea: fix use after free" patch)
Currently ehea stats are broken. The bytes counters are got from
the hardware, while the packets counters are got from the device
driver. Also, the device driver counters are resetted during the
the down process, and the hardware aren't, causing some weird
numbers.
This patch just consolidates the packets and bytes on the device
driver.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Jay Vosburgh <fubar@us.ibm.com>
Pavel Emelyanov [Wed, 27 Oct 2010 05:43:53 +0000 (05:43 +0000)]
tunnels: Fix tunnels change rcu protection
After making rcu protection for tunnels (ipip, gre, sit and ip6) a bug
was introduced into the SIOCCHGTUNNEL code.
The tunnel is first unlinked, then addresses change, then it is linked
back probably into another bucket. But while changing the parms, the
hash table is unlocked to readers and they can lookup the improper tunnel.
Respective commits are b7285b79 (ipip: get rid of ipip_lock), 1507850b
(gre: get rid of ipgre_lock), 3a43be3c (sit: get rid of ipip6_lock) and 94767632 (ip6tnl: get rid of ip6_tnl_lock).
The quick fix is to wait for quiescent state to pass after unlinking,
but if it is inappropriate I can invent something better, just let me
know.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 26 Oct 2010 02:20:56 +0000 (02:20 +0000)]
drivers/isdn: delete double assignment
Delete successive assignments to the same location. In the first case, the
hscx array has two elements, so change the assignment to initialize the
second one. In the second case, the two assignments are simply identical.
Furthermore, neither is necessary, because the effect of the assignment is
only visible in the next line, in the assignment in the if test. The patch
inlines the right hand side value in the latter assignment and pulls that
assignment out of the if test.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 26 Oct 2010 00:25:36 +0000 (00:25 +0000)]
drivers/net/typhoon.c: delete double assignment
Delete successive assignments to the same location. The current definition
does not initialize the respRing structure, which has the same type as the
cmdRing structure, so initialize that one instead.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: David Dillow <dave@thedillows.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 26 Oct 2010 00:25:34 +0000 (00:25 +0000)]
drivers/net/sb1000.c: delete double assignment
The other code around these duplicated assignments initializes the 0 1 2
and 3 elements of an array, so change the initialization of the
rx_session_id array to do the same.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Sony Chacko [Tue, 26 Oct 2010 17:53:09 +0000 (17:53 +0000)]
qlcnic: define valid vlan id range
4095 vlan id is reserved and should not be use.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sony Chacko [Tue, 26 Oct 2010 17:53:08 +0000 (17:53 +0000)]
qlcnic: reduce rx ring size
If eswitch is enabled, rcv ring size can be reduce, as
physical port is partition-ed.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
amit salecha [Tue, 26 Oct 2010 17:53:07 +0000 (17:53 +0000)]
qlcnic: fix mac learning
In failover bonding case, same mac address can be programmed on other slave function.
Fw will delete old entry (original func) associated with that mac address.
Need to reporgram mac address, if failover again happen to original function.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 26 Oct 2010 19:21:07 +0000 (19:21 +0000)]
ehea: fix use after free
ehea_start_xmit() dereferences skb after its freeing in ehea_xmit3() to
get vlan tags.
Move the offending block before the potential ehea_xmit3() call.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Wed, 27 Oct 2010 04:58:12 +0000 (04:58 +0000)]
qlge: bugfix: Restoring the vlan setting.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Mon, 25 Oct 2010 23:01:03 +0000 (23:01 +0000)]
be2net: Schedule/Destroy worker thread in probe()/remove() rather than open()/close()
When async mcc compls are rcvd on an i/f that is down (and so interrupts are disabled)
they just lie unprocessed in the compl queue.The compl queue can eventually get filled
up and cause the BE to lock up.The fix is to use be_worker to reap mcc compls when the
i/f is down.be_worker is now launched in be_probe() and canceled in be_remove().
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Sun, 24 Oct 2010 23:06:43 +0000 (23:06 +0000)]
ipv6: fix refcnt problem related to POSTDAD state
After running this bonding setup script
modprobe bonding miimon=100 mode=0 max_bonds=1
ifconfig bond0 10.1.1.1/16
ifenslave bond0 eth1
ifenslave bond0 eth3
on s390 with qeth-driven slaves, modprobe -r fails with this message
unregister_netdevice: waiting for bond0 to become free. Usage count = 1
due to twice detection of duplicate address.
Problem is caused by a missing decrease of ifp->refcnt in addrconf_dad_failure.
An extra call of in6_ifa_put(ifp) solves it.
Problem has been introduced with commit f2344a131bccdbfc5338e17fa71a807dee7944fa.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Cc: David S. Miller <davem@davemloft.net> Cc: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Fri, 22 Oct 2010 04:38:26 +0000 (04:38 +0000)]
net: NETIF_F_HW_CSUM does not imply FCoE CRC offload
NETIF_F_HW_CSUM indicates the ability to update an TCP/IP-style 16-bit
checksum with the checksum of an arbitrary part of the packet data,
whereas the FCoE CRC is something entirely different.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Cc: stable@kernel.org [2.6.32+] Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Fri, 22 Oct 2010 04:12:19 +0000 (04:12 +0000)]
net: Fix some corner cases in dev_can_checksum()
dev_can_checksum() incorrectly returns true in these cases:
1. The skb has both out-of-band and in-band VLAN tags and the device
supports checksum offload for the encapsulated protocol but only with
one layer of encapsulation.
2. The skb has a VLAN tag and the device supports generic checksumming
but not in conjunction with VLAN encapsulation.
Rearrange the VLAN tag checks to avoid these.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Tue, 19 Oct 2010 00:06:36 +0000 (00:06 +0000)]
gianfar: Fix crashes on RX path (Was Re: [Bugme-new] [Bug 19692] New: linux-2.6.36-rc5 crash with gianfar ethernet at full line rate traffic)
The rx_recycle queue is global per device but can be accesed by many
napi handlers at the same time, so it needs full skb_queue primitives
(with locking). Otherwise, various crashes caused by broken skbs are
possible.
This patch resolves, at least partly, bugzilla bug 19692. (Because of
some doubts that there could be still something around which is hard
to reproduce my proposal is to leave this bug opened for a month.)
Reported-by: emin ak <eminak71@gmail.com> Tested-by: emin ak <eminak71@gmail.com> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> CC: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug in the interaction between ipv6_create_tempaddr and
addrconf_verify. Because ipv6_create_tempaddr uses the cstamp and tstamp
from the public address in creating a private address, if we have not
received a router advertisement in a while, tstamp + temp_valid_lft might be
< now. If this happens, the new address is created inside
ipv6_create_tempaddr, then the loop within addrconf_verify starts again and
the address is immediately deleted. We are left with no temporary addresses
on the interface, and no more will be created until the public IP address is
updated. To avoid this, set the expiry time to be the minimum of the time
left on the public address or the config option PLUS the current age of the
public interface.
Signed-off-by: Glenn Wurster <gwurster@scs.carleton.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 23 Oct 2010 09:44:25 +0000 (09:44 +0000)]
fib: fix fib_nl_newrule()
Some panic reports in fib_rules_lookup() show a rule could have a NULL
pointer as a next pointer in the rules_list.
This can actually happen because of a bug in fib_nl_newrule() : It
checks if current rule is the destination of unresolved gotos. (Other
rules have gotos to this about to be inserted rule)
Problem is it does the resolution of the gotos before the rule is
inserted in the rules_list (and has a valid next pointer)
Fix this by moving the rules_list insertion before the changes on gotos.
A lockless reader can not any more follow a ctarget pointer, unless
destination is ready (has a valid next pointer)
Reported-by: Oleg A. Arkhangelsky <sysoleg@yandex.ru> Reported-by: Joe Buehler <aspam@cox.net> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: Do not call device_set_wakeup_enable() under spin_lock_bh
The tg3 driver calls device_set_wakeup_enable() under spin_lock_bh,
which causes a problem to happen after the recent core power
management changes, because this function can sleep now. Fix this
by moving the device_set_wakeup_enable() call out of the
spin_lock_bh-protected area.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Mon, 25 Oct 2010 23:47:36 +0000 (16:47 -0700)]
pch_can: depends on PCI
Fix pch_can build when CONFIG_PCI is not enabled. It uses pci interfaces
and data structures, so it should depend on PCI.
drivers/net/can/pch_can.c:1044: error: implicit declaration of function 'pci_enable_msi'
drivers/net/can/pch_can.c:1079: error: implicit declaration of function 'pci_disable_msi'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
KOVACS Krisztian [Sun, 24 Oct 2010 23:38:32 +0000 (23:38 +0000)]
netfilter: fix module dependency issues with IPv6 defragmentation, ip6tables and xt_TPROXY
One of the previous tproxy related patches split IPv6 defragmentation and
connection tracking, but did not correctly add Kconfig stanzas to handle the
new dependencies correctly. This patch fixes that by making the config options
mirror the setup we have for IPv4: a distinct config option for defragmentation
that is automatically selected by both connection tracking and
xt_TPROXY/xt_socket.
The patch also changes the #ifdefs enclosing IPv6 specific code in xt_socket
and xt_TPROXY: we only compile these in case we have ip6tables support enabled.
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 25 Oct 2010 19:51:55 +0000 (12:51 -0700)]
net: Increase xmit RECURSION_LIMIT to 10.
Three is definitely too low, and we know from reports that GRE tunnels
stacked as deeply as 37 levels cause stack overflows, so pick some
reasonable value between those two.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Mon, 25 Oct 2010 02:56:47 +0000 (02:56 +0000)]
mlx4_en: Fix out of bounds array access
When searching for a free entry in either mlx4_register_vlan() or
mlx4_register_mac(), and there is no free entry, the loop terminates without
updating the local variable free thus causing out of array bounds access. Fix
this by adding a proper check outside the loop.
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Joshua Hoke [Mon, 25 Oct 2010 01:44:22 +0000 (01:44 +0000)]
macb: Don't re-enable interrupts while in polling mode
On a busy network, the macb driver could get stuck in the interrupt
handler, quickly triggering the watchdog, due to a confluence of
factors:
1. macb_poll re-enables interrupts unconditionally, even when it will
be called again because it exhausted its rx budget
2. macb_interrupt only disables interrupts after scheduling
macb_poll, but scheduling fails when macb_poll is already scheduled
because it didn't call napi_complete
3. macb_interrupt loops until the interrupt status register is clear,
which will never happen in this case if the driver doesn't disable
the RX interrupt
Since macb_interrupt runs in interrupt context, this effectively locks
up the machine, triggering the hardware watchdog.
This issue was readily reproducible on a flooded network with a
modified 2.6.27.48 kernel. The same problem appears to still be in the
2.6.36-rc8 driver code, so I am submitting this patch against that
version. I have not tested this version of the patch except to make
sure the kernel compiles.
Signed-off-by: Joshua Hoke <joshua.hoke@sixnet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Mon, 25 Oct 2010 01:11:58 +0000 (01:11 +0000)]
be2net: Fix CSO for UDP packets
We're setting skb->ip_summed to CHECKSUM_NONE for all non-TCP pkts, making the stack
recompute checksum.This is a bug for UDP pkts for which cso must be used.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Mon, 25 Oct 2010 01:11:10 +0000 (01:11 +0000)]
be2net: Call netif_carier_off() after register_netdev()
Calling netif_carrier_off before register_netdev was causing the network interface
to miss a linkwatch pending event leading to an inconsistent state if the link
is not up when interface is initialized.This is now invoked after register_netdev.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Don Fry [Sat, 23 Oct 2010 16:02:50 +0000 (09:02 -0700)]
iwlwifi: quiet a noisy printk
Timing issues in microcode for some devices can cause a compressed BA to
be sent to the driver prior to returning any a-MPDU notification.
Traces show RTS-CTS is exchanged and then the timer fires which causes an
empty BA to be sent which acknowledges nothing. This results in a noisy
printk. Only print the message if the bitmap is non-zero.
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 23 Oct 2010 15:45:38 +0000 (17:45 +0200)]
ath9k: resume aggregation immediately after a hardware reset
Since aggregation is usually triggered by tx completion, a hardware
reset (because of beacon stuck, tx hang or baseband hang) can
significantly delay the transmission of the next AMPDU (until the next
tx completion event).
Fix this by rescheduling aggregation after such a reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Fix ibss station got expired immediately
Station addition in ieee80211_ibss_rx_queued_mgmt is not updating
sta->last_rx which is causing station expiry in ieee80211_ibss_work
path. So sta addition and deletion happens repeatedly.
CC: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 21 Oct 2010 00:47:24 +0000 (02:47 +0200)]
ath9k: fix handling of rate control probe frames
The ath9k aggregation code was already checking the rate control probe flag
to prevent starting an aggregate frame with a sampling rate. What was missing
was closing an aggregate before adding a probing frame to it.
Without that, rate control cannot have precise control over probing, which
delays using faster rates when the channel conditions improve.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Fix TX carrier leakage for IEEE compliance on AR9003 2.2
This updates the initvals for the AR9003 2.2 chipsets. The initvals
are the initial register values we use for our registers upon hardware
reset. This synchs up the initvals to match what our latest recommendation
from our systems engineering team.
The description of changes in this update:
Improves ability to support very strong Rx conditions.
Enhances DFS support for AP-mode.
Improves performance of Tx carrier leak calibration.
Adds support for Japan channel 14 Tx filtering requirements.
Improves Tx power accuracy.
Impact:
Update required to address degraded throughput at very short range.
Update required for AP-mode DFS certification.
Update required to comply to IEEE Tx carrier leak specification.
May not meet expected +/- 2 dB Tx power accuracy without update.
The most important fix here would be the TX carrier leakage required
to comply with IEEE 802.11 specifications. The group of changes have
been tested all together in one release.
Cc: stable@kernel.org Cc: Yixiang Li <yixiang.li@atheros.com> Cc: Don Breslin <don.breslin@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless: only use alpha2 regulatory information from country IE
removed some complex intersection we were always doing between the AP's
country IE info and what we got from CRDA. When CRDA sent us back a
regulatory domain we would do some sanity checks on that regulatory
domain response we just got. Part of these sanity checks included
checking that we already had performed an intersection for the
request of NL80211_REGDOM_SET_BY_COUNTRY_IE type.
This mean that cfg80211 was only processing country IEs for cases
where we already had an intersection, but since we removed enforcing
this this is no longer required, we should just apply the country
IE country hint with the data received from CRDA.
This patch has fixes intended for kernels >= 2.6.36.
Cc: stable@kernel.org Reported-by: Easwar Krishnan <easwar.krishnan@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170: fix memory leak issue in async cmd macro wrappers
This patch continues where the previous commit:
"carl9170: fix async command buffer leak"
left off.
Similar to carl9170_reboot/carl9170_powersave, the
carl9170_async_regwrite* macros would leak the
temporary command buffer, if __carl9170_exec_cmd
fails to upload the command to the device.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
I found this bug while poking around with a pure-gn AP.
Commit:
cfg80211/mac80211: Use more generic bitrate mask for rate control
Added some sanity checks to ensure that each tx rate index
is included in the configured mask and it would change any
rate indexes if it wasn't.
But, the current implementation doesn't take into account
that the invalid rate index "-1" has a special meaning
(= no further attempts) and it should not be "changed".
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
If __carl9170_exec_cmd fails to upload an asynchronous
command to the device, the functions: carl9170_reboot
and carl9170_powersave will leak the temporary command
assembly buffer.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tejun Heo [Fri, 15 Oct 2010 15:35:28 +0000 (17:35 +0200)]
mac80211: cancel restart_work explicitly instead of depending on flush_scheduled_work()
iee80211_hw->restart_work is the only work which uses the system
workqueue. Instead of calling flush_scheduled_work() during
iee80211_exit(), cancel the work during unregistration.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stephen Rothwell [Mon, 25 Oct 2010 05:26:41 +0000 (22:26 -0700)]
l2tp: static functions should not be exported
Causes these build failures on PowerPC:
net/l2tp/l2tp_core.c:1228: error: __ksymtab_l2tp_tunnel_closeall causes a section type conflict
net/l2tp/l2tp_core.c:1228: error: __ksymtab_l2tp_tunnel_closeall causes a section type conflict
net/l2tp/l2tp_core.c:1006: error: __ksymtab_l2tp_xmit_core causes a section type conflict
net/l2tp/l2tp_core.c:1006: error: __ksymtab_l2tp_xmit_core causes a section type conflict
net/l2tp/l2tp_core.c:847: error: __ksymtab_l2tp_udp_recv_core causes a section type conflict
net/l2tp/l2tp_core.c:847: error: __ksymtab_l2tp_udp_recv_core causes a section type conflict
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David Dillow [Sun, 24 Oct 2010 10:20:20 +0000 (10:20 +0000)]
typhoon: wait for RX mode commands to finish
When adding VLAN devices, we can get several calls to
typhoon_set_rx_mode() in quick succession. Because we didn't wait for
the commands to complete, we could run out of command descriptors and
fail to set the RX mode.
Signed-off-by: David Dillow <dave@thedillows.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 24 Oct 2010 04:27:10 +0000 (04:27 +0000)]
netlink: fix netlink_change_ngroups()
commit 6c04bb18ddd633 (netlink: use call_rcu for netlink_change_ngroups)
used a somewhat convoluted and racy way to perform call_rcu().
The old block of memory is freed after a grace period, but the rcu_head
used to track it is located in new block.
This can clash if we call two times or more netlink_change_ngroups(),
and a block is freed before another. call_rcu() called on different cpus
makes no guarantee in order of callbacks.
Fix this using a more standard way of handling this : Each block of
memory contains its own rcu_head, so that no 'use after free' can
happens.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Johannes Berg <johannes@sipsolutions.net> CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guo-Fu Tseng [Sun, 24 Oct 2010 23:18:25 +0000 (16:18 -0700)]
jme: Support WoL after shutdown
Adding shutdown function that setup wake if wol is enabled.
Add jme_phy_on in jme_set_100m_half in case it is shutting down
or suspending when interface is down(phy_off by default).
v2 updates:
Removed CONFIG_PM ifdef for jme_set_100m_half and jme_wait_link.
It would be nice if it can be applied to net-2.6 along with other patches
sent few days ago. If it is not appropriate, please ignore the net-2.6
request, and apply it to net-next-2.6 as previous patch. :)
Reported-and-helped-by: Сtac <Taoga@yandex.ru> Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Thu, 21 Oct 2010 18:05:34 +0000 (18:05 +0000)]
vmxnet3: fix typo setting confPA
It's a le64, not a le32, typo in one place only.
Noticed by sparse:
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: warning: incorrect type in assignment (different base types)
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: expected restricted __le64 [usertype] confPA
drivers/net/vmxnet3/vmxnet3_drv.c:2668:52: got restricted __le32 [usertype] <noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Thu, 21 Oct 2010 18:05:33 +0000 (18:05 +0000)]
vmxnet3: annotate hwaddr members as __iomem pointers
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Thu, 21 Oct 2010 18:05:32 +0000 (18:05 +0000)]
vmxnet3: remove set_flag_le{16,64} helpers
It's easier to just annotate the constants as little endian types and set/clear
the flags directly.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4: fix crash due to manipulating queues before registration
Before commit "net: allocate tx queues in register_netdevice"
netif_tx_stop_all_queues and related functions could be used between
device allocation and registration but now only after registration.
cxgb4 has such a call before registration and crashes now. Move it
after register_netdev.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for Technologic Systems TS-CAN1 PC104 peripheral boards.
Signed-off-by: Andre B. Oliveira <anbadeol@gmail.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Anders Franzen [Tue, 19 Oct 2010 03:50:47 +0000 (03:50 +0000)]
ip6_tunnel dont update the mtu on the route.
The ip6_tunnel device did not unset the flag,
IFF_XMIT_DST_RELEASE. This will make the dev layer
to release the dst before calling the tunnel.
The tunnel will not update any mtu/pmtu info, since
it does not have a dst on the skb. Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker [Mon, 18 Oct 2010 12:14:44 +0000 (12:14 +0000)]
pktgen: clean up handling of local/transient counter vars
The temporary variable "i" is needlessly initialized to zero
in two distinct cases in this file:
1) where it is set to zero and then used as an argument in an addition
before being assigned a non-zero value.
2) where it is only used in a standard/typical loop counter
For (1), simply delete assignment to zero and usages while still
zero; for (2) simply make the loop start at zero as per standard
practice as seen everywhere else in the same file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following functions are not used directly by any drivers:
phy_attach_direct
phy_device_create
phy_prepare_link
genphy_config_advert
genphy_setup_forced
phy_config_interrupt
phy_clear_interrypt
phy_sanitize_settings
phy_enable_interrupts
phy_disable_interrupts
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>