Ben Hutchings [Tue, 5 Mar 2013 17:49:39 +0000 (17:49 +0000)]
sfc: Correct efx_rx_buffer::page_offset when EFX_PAGE_IP_ALIGN != 0
RX DMA buffers start at an offset of EFX_PAGE_IP_ALIGN bytes from the
start of a cache line. This offset obviously needs to be included in
the virtual address, but this was missed in commit b590ace09d51
('sfc: Fix efx_rx_buf_offset() in the presence of swiotlb') since
EFX_PAGE_IP_ALIGN is equal to 0 on both x86 and powerpc.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 5 Mar 2013 01:03:47 +0000 (01:03 +0000)]
sfc: Disable soft interrupt handling during efx_device_detach_sync()
efx_device_detach_sync() locks all TX queues before marking the device
detached and thus disabling further TX scheduling. But it can still
be interrupted by TX completions which then result in TX scheduling in
soft interrupt context. This will deadlock when it tries to acquire
a TX queue lock that efx_device_detach_sync() already acquired.
To avoid deadlock, we must use netif_tx_{,un}lock_bh().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Mon, 28 Jan 2013 19:01:06 +0000 (19:01 +0000)]
sfc: Detach net device when stopping queues for reconfiguration
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
The device is ready if all the following are true:
(a) It has a qdisc
(b) It is marked present
(c) It is running
(d) The link is reported up
(a) and (c) are normally true, and must not be changed by a driver.
(d) is under our control, but fake link changes may disturb userland.
This leaves (b). We already mark the device absent during reset
and self-test, but we need to do the same during MTU changes and ring
reallocation. We don't need to do this when the device is brought
down because then (c) is already false.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 10 Jan 2013 23:51:54 +0000 (23:51 +0000)]
sfc: Fix efx_rx_buf_offset() in the presence of swiotlb
We assume that the mapping between DMA and virtual addresses is done
on whole pages, so we can find the page offset of an RX buffer using
the lower bits of the DMA address. However, swiotlb maps in units of
2K, breaking this assumption.
Add an explicit page_offset field to struct efx_rx_buffer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 20 Dec 2012 18:48:20 +0000 (18:48 +0000)]
sfc: Properly sync RX DMA buffer when it is not the last in the page
We may currently allocate two RX DMA buffers to a page, and only unmap
the page when the second is completed. We do not sync the first RX
buffer to be completed; this can result in packet loss or corruption
if the last RX buffer completed in a NAPI poll is the first in a page
and is not DMA-coherent. (In the middle of a NAPI poll, we will
handle the following RX completion and unmap the page *before* looking
at the content of the first buffer.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ming Lei [Fri, 22 Feb 2013 03:05:05 +0000 (03:05 +0000)]
usbnet: smsc95xx: rename FEATURE_AUTOSUSPEND
The name of FEATURE_AUTOSUSPEND is very misleading and the actual
meaning is remote wakeup, but a device incapable of remote wakeup
still can support USB autosuspend under some situations, so rename
it to avoid misunderstanding.
Cc: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ming Lei [Fri, 22 Feb 2013 03:05:04 +0000 (03:05 +0000)]
usbnet: smsc95xx: fix broken runtime suspend
Commit b2d4b150(smsc95xx: enable dynamic autosuspend) implements
autosuspend, but breaks current runtime suspend, such as:
when the interface becomes down, the usb device can't be put into
runtime suspend any more.
This patch fixes the broken runtime suspend.
Cc: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
return > 0 in case of success, so they will cause smsc95xx_suspend()
to return > 0 and cause suspend failure.
The bug is introduced in commit 3b9f7d(smsc95xx: fix error handling
in suspend failure case).
Cc: <stable@vger.kernel.org> [3.8] Cc: Steve Glendinning <steve.glendinning@shawell.net> Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Larry Finger [Mon, 25 Feb 2013 06:09:24 +0000 (06:09 +0000)]
b43: Fix lockdep splat on module unload
On unload, b43 produces a lockdep warning that can be summarized in the
following way:
======================================================
[ INFO: possible circular locking dependency detected ]
3.8.0-wl+ #117 Not tainted
-------------------------------------------------------
modprobe/5557 is trying to acquire lock:
((&wl->firmware_load)){+.+.+.}, at: [<ffffffff81062160>] flush_work+0x0/0x2a0
but task is already holding lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff813bd7d2>] rtnl_lock+0x12/0x20
which lock already depends on the new lock.
[ INFO: possible circular locking dependency detected ]
======================================================
The full output is available at http://lkml.indiana.edu/hypermail/linux/kernel/1302.3/00060.html.
To summarize, commit 6b6fa58 added a 'cancel_work_sync(&wl->firmware_load)'
call in the wrong place.
The fix is to move the cancel_work_sync() call to b43_bcma_remove() and
b43_ssb_remove(). Thanks to Johannes Berg and Michael Buesch for help in
diagnosing the log output.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [V3.5+] Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Sun, 24 Feb 2013 20:05:05 +0000 (20:05 +0000)]
IP_GRE: Fix GRE_CSUM case.
commit "ip_gre: allow CSUM capable devices to handle packets" aa0e51cdda005cd37e2, broke GRE_CSUM case.
GRE_CSUM needs checksum computed for inner packet. Therefore
csum-calculation can not be offloaded if tunnel device requires
GRE_CSUM. Following patch fixes it by computing inner packet checksum
for GRE_CSUM type, for all other type of GRE devices csum is offloaded.
CC: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Fri, 22 Feb 2013 07:30:30 +0000 (07:30 +0000)]
IP_GRE: Fix IP-Identification.
GRE-GSO generates ip fragments with id 0,2,3,4... for every
GSO packet, which is not correct. Following patch fixes it
by setting ip-header id unique id of fragments are allowed.
As Eric Dumazet suggested it is optimized by using inner ip-header
whenever inner packet is ipv4.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Fri, 22 Feb 2013 10:32:24 +0000 (10:32 +0000)]
vmxnet3: fix ethtool ring buffer size setting
Noticed that vmxnet3's get_ringparam function was returning the summation of all
ring buffers on a NIC, rather than just the size of any one ring. This causes
problems when a vmxnet3 instance has multiple queues, as ethtool, when setting
ring parameters, first gets the current ring parameters to set the existing
values in the set_ringparm commannd. The result is, that unless both rx and tx
ring sizes are set in a single operation, which ever ring is not set will
silently have its ring count multiplied by the number of queues on the NIC until
it reaches a driver defined maxiumum value.
Fix it by not multiplying the rx and tx ring sizes by the number of queues in
the system, like every other driver. Tested by myself successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Shreyas Bhatewara <sbhatewara@vmware.com> CC: "VMware, Inc." <pv-drivers@vmware.com> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: remove dead code and make local funcs static
Sparse warned about several functions that were unnecessarily global.
After making them static, discovered that several functions were actually never used.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Eilon Greenstein <eilong@broadcomo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker [Sun, 24 Feb 2013 05:38:31 +0000 (05:38 +0000)]
gianfar: fix compile fail for NET_POLL=y due to struct packing
Commit ee873fda3bec7c668407b837fc5519eb961fcd37 ("gianfar: Pack struct
gfar_priv_grp into three cachelines") moved the irq number and names
off into a separate struct and created accessors for them. However
it was never tested with NET_POLL enabled, and so some conversions
that were simply overlooked went undetected until now.
Make the netpoll ones also use the gfar_irq() accessors.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Claudiu Manoil <claudiu.manoil@freescale.com> Cc: Jianhua Xie <jianhua.xie@freescale.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
won't be correct. But __pop_vlan_tci() assumes points _before_
mac addr.
In vlan_set_encap_proto(), it looks for some magic L2 value
after mac addr:
rawp = skb->data;
if (*(unsigned short *) rawp == 0xFFFF)
...
Therefore __pop_vlan_tci() is obviously wrong.
A quick fix is avoiding using skb->data in vlan_set_encap_proto(),
use 'vhdr+1' is always correct in both cases.
Cc: David S. Miller <davem@davemloft.net> Cc: Jesse Gross <jesse@nicira.com> Signed-off-by: Cong Wang <amwang@redhat.com> Acked-by: Jesse Gross <jesse@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mathias Krause [Sat, 23 Feb 2013 01:13:48 +0000 (01:13 +0000)]
sock_diag: Simplify sock_diag_handlers[] handling in __sock_diag_rcv_msg
The sock_diag_lock_handler() and sock_diag_unlock_handler() actually
make the code less readable. Get rid of them and make the lock usage
and access to sock_diag_handlers[] clear on the first sight.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mathias Krause [Sat, 23 Feb 2013 01:13:47 +0000 (01:13 +0000)]
sock_diag: Fix out-of-bounds access to sock_diag_handlers[]
Userland can send a netlink message requesting SOCK_DIAG_BY_FAMILY
with a family greater or equal then AF_MAX -- the array size of
sock_diag_handlers[]. The current code does not test for this
condition therefore is vulnerable to an out-of-bound access opening
doors for a privilege escalation.
Signed-off-by: Mathias Krause <minipli@googlemail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Fri, 22 Feb 2013 21:25:38 +0000 (21:25 +0000)]
vxlan: remove depends on CONFIG_EXPERIMENTAL
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en: fix allocation of CPU affinity reverse-map
The mlx4_en driver allocates the number of objects for the CPU affinity
reverse-map based on the number of rx rings of the device. However,
mlx4_assign_eq() calls irq_cpu_rmap_add() as many times as IRQ's are
assigned to EQ's, which can be as large as mlx4_dev->caps.comp_pool. If
caps.comp_pool is larger than rx_ring_num we will eventually hit the
BUG_ON() in cpu_rmap_add().
Fix this problem by allocating space for the maximum number of CPU
affinity reverse-map objects we might want to add.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Acked-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The memory to hold the network device tx_cq is not being allocated with
the correct size in mlx4_en_init_netdev(). It should use MAX_TX_RINGS
instead of MAX_RX_RINGS. This can cause problems if the number of tx
rings being used is greater than MAX_RX_RINGS.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Acked-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Fri, 22 Feb 2013 08:59:06 +0000 (08:59 +0000)]
tcp: fix SYN-data space mis-accounting
In fast open the sender unncessarily reduces the space available
for data in SYN by 12 bytes. This is because in the sender
incorrectly reserves space for TS option twice in tcp_send_syn_data():
tcp_mtu_to_mss() already accounts for TS option space. But it further
reserves MAX_TCP_OPTION_SPACE when computing the payload space.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 22 Feb 2013 07:43:35 +0000 (07:43 +0000)]
net: fix possible deadlock in sum_frag_mem_limit
Dave Jones reported a lockdep splat occurring in IP defrag code.
commit 6d7b857d541ecd1d (net: use lib/percpu_counter API for
fragmentation mem accounting) added a possible deadlock.
Because percpu_counter_sum_positive() needs to acquire
a lock that can be used from softirq, we need to disable BH
in sum_frag_mem_limit()
Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Estevam [Fri, 22 Feb 2013 06:40:45 +0000 (06:40 +0000)]
net: fec: Fix division by zero
commit 7f7d6c282 (net: fec: Ensure that initialization is done prior to
request_irq()) placed fec_ptp_init() into a point that ptp clock was not
available, which causes a division by zero in fec_ptp_start_cyclecounter():
[ 17.895723] Division by zero in kernel.
[ 17.899571] Backtrace:
[ 17.902094] [<80012564>] (dump_backtrace+0x0/0x10c) from [<8056deec>]
(dump_stack+0x18/0x1c)
[ 17.910539] r6:bfba8500 r5:8075c950 r4:bfba8000 r3:bfbd0000
[ 17.916284] [<8056ded4>] (dump_stack+0x0/0x1c) from [<80012688>]
(__div0+0x18/0x20)
[ 17.923968] [<80012670>] (__div0+0x0/0x20) from [<802829c4>] (Ldiv0+0x8/0x10)
[ 17.931140] [<80398534>] (fec_ptp_start_cyclecounter+0x0/0x110) from
[<80394f64>] (fec_restart+0x6c8/0x754)
[ 17.940898] [<8039489c>] (fec_restart+0x0/0x754) from [<803969a0>]
(fec_enet_adjust_link+0xdc/0x108)
[ 17.950046] [<803968c4>] (fec_enet_adjust_link+0x0/0x108) from [<80390bc4>]
(phy_state_machine+0x178/0x534)
...
Fix this by rearraging the code so that fec_ptp_init() is called only after
the clocks have been properly acquired.
Tested on both mx53 and mx6 platforms.
Reported-by: Jim Baxter <jim_baxter@mentor.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li Wei [Thu, 21 Feb 2013 22:18:44 +0000 (22:18 +0000)]
ipv4: fix error handling in icmp_protocol.
Now we handle icmp errors in each transport protocol's err_handler,
for icmp protocols, that is ping_err. Since this handler only care
of those icmp errors triggered by echo request, errors triggered
by echo reply(which sent by kernel) are sliently ignored.
So wrap ping_err() with icmp_err() to deal with those icmp errors.
Signed-off-by: Li Wei <lw@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Fri, 22 Feb 2013 13:32:20 +0000 (21:32 +0800)]
brcmfmac: fix missing unlock on error in brcmf_notify_vif_event()
Add the missing unlock before return from function brcmf_notify_vif_event()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Thu, 21 Feb 2013 05:12:58 +0000 (21:12 -0800)]
mwifiex: fix system freeze while reloading driver
Unload sequence for mwifiex PCIE driver is as follows:
1. Invoking cleanup module from kernel results into
pci_unregister_driver
2. Kernel invokes PCIE remove() handler which disconnects all
interfaces.
3. One step during disconnect is to clean PCIE TX rings.
During this we read txbd_rdptr from FW.
While loading driver next time, we see pci_enable_device()
results into system freeze. This may have happened because we
accessed PCI device after unregistering from bus driver.
Removing this ioread() operation resolves this bug.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Tue, 19 Feb 2013 20:09:47 +0000 (15:09 -0500)]
mwifiex: don't drop carrier flag over suspend
If the system suspends with mwifiex wifi powered on, and is then woken
by an ICMP ping packet, the ping response is discarded by the kernel
because the kernel incorrectly thinks there is no carrier.
I can't see any valid reason to want to report loss of carrier here,
so remove the offending code.
Fixes http://dev.laptop.org/ticket/12554
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eric Dumazet [Thu, 21 Feb 2013 12:18:52 +0000 (12:18 +0000)]
ipv6: use a stronger hash for tcp
It looks like its possible to open thousands of TCP IPv6
sessions on a server, all landing in a single slot of TCP hash
table. Incoming packets have to lookup sockets in a very
long list.
We should hash all bits from foreign IPv6 addresses, using
a salt and hash mix, not a simple XOR.
inet6_ehashfn() can also separately use the ports, instead
of xoring them.
Reported-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Thu, 21 Feb 2013 11:09:47 +0000 (11:09 +0000)]
qlcnic: Fix configure interrupts for 83xx adapter types
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com> Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh [Thu, 21 Feb 2013 11:09:46 +0000 (11:09 +0000)]
qlcnic: Fix internal loopback test for 82xx adapter
o Use correct function to clear loopback mode.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that such initialization functions are called prior to requesting the
interrupts, so that all necessary the data structures are in place when the
irqs occur.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
timestamp offset. From Andrey Vagin.
2) VMWARE VM VSOCK layer, from Andy King.
3) Much improved support for virtual functions and SR-IOV in bnx2x,
from Ariel ELior.
4) All protocols on ipv4 and ipv6 are now network namespace aware, and
all the compatability checks for initial-namespace-only protocols is
removed. Thanks to Tom Parkin for helping deal with the last major
holdout, L2TP.
5) IPV6 support in netpoll and network namespace support in pktgen,
from Cong Wang.
6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
Protocol (MVRP) support, from David Ward.
7) Compute packet lengths more accurately in the packet scheduler, from
Eric Dumazet.
8) Use per-task page fragment allocator in skb_append_datato_frags(),
also from Eric Dumazet.
9) Add support for connection tracking labels in netfilter, from
Florian Westphal.
10) Fix default multicast group joining on ipv6, and add anti-spoofing
checks to 6to4 and 6rd. From Hannes Frederic Sowa.
11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
times, rearrange inet frag datastructures for better cacheline
locality, and move more operations outside of locking. From Jesper
Dangaard Brouer.
12) Instead of strict master <--> slave relationships, allow arbitrary
scenerios with "upper device lists". From Jiri Pirko.
13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
Pirko.
14) Add a BPF filter netfilter match target, from Willem de Bruijn.
15) Orphan and delete a bunch of pre-historic networking drivers from
Paul Gortmaker.
16) Add TSO support for GRE tunnels, from Pravin B SHelar. Although
this still needs some minor bug fixing before it's %100 correct in
all cases.
17) Handle unresolved IPSEC states like ARP, with a resolution packet
queue. From Steffen Klassert.
18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
Hemminger. This was long overdue.
19) Support SO_REUSEPORT, from Tom Herbert.
20) Allow locking a socket BPF filter, so that it cannot change after a
process drops capabilities.
21) Add VLAN filtering to bridge, from Vlad Yasevich.
22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
the ipv6 routes, from YOSHIFUJI Hideaki.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
ipv6: fix race condition regarding dst->expires and dst->from.
net: fix a wrong assignment in skb_split()
ip_gre: remove an extra dst_release()
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
atl1c: restore buffer state
net: fix a build failure when !CONFIG_PROC_FS
net: ipv4: fix waring -Wunused-variable
net: proc: fix build failed when procfs is not configured
Revert "xen: netback: remove redundant xenvif_put"
net: move procfs code to net/core/net-procfs.c
qmi_wwan, cdc-ether: add ADU960S
bonding: set sysfs device_type to 'bond'
bonding: fix bond_release_all inconsistencies
b44: use netdev_alloc_skb_ip_align()
xen: netback: remove redundant xenvif_put
net: fec: Do a sanity check on the gpio number
ip_gre: propogate target device GSO capability to the tunnel device
ip_gre: allow CSUM capable devices to handle packets
bonding: Fix initialize after use for 3ad machine state spinlock
bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
...
Linus Torvalds [Wed, 20 Feb 2013 22:30:33 +0000 (14:30 -0800)]
Merge tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 patches from Catalin Marinas:
- SMP support for the PSCI booting protocol (power state coordination
interface).
- Simple earlyprintk support.
- Platform devices populated by default from the DT (SoC-agnostic).
- CONTEXTIDR support (used by external trace tools).
* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: mm: update CONTEXTIDR register to contain PID of current process
arm64: atomics: fix grossly inconsistent asm constraints for exclusives
arm64: compat: use compat_uptr_t type for compat_ucontext.uc_link
arm64: Select ARCH_WANT_FRAME_POINTERS
arm64: Add kvm_para.h and xor.h generic headers
arm64: SMP: enable PSCI boot method
arm64: psci: add support for PSCI invocations from the kernel
arm64: SMP: rework the SMP code to be enabling method agnostic
arm64: perf: add guest vs host discrimination
arm64: add COMPAT_PSR_*_BIT flags
arm64: Add simple earlyprintk support
arm64: Populate the platform devices
Linus Torvalds [Wed, 20 Feb 2013 22:27:58 +0000 (14:27 -0800)]
Merge branch 'for-linus' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM updates (part one) from Russell King:
- MMC patches from Ulf Hansson and Pawel Moll. These add support for
DDR mode and the latest variant found on ARM Versatile Express, as
well as a number of cleanups.
- A fix for to improve the behaviour of ARMs sched_clock()
- Changes to the ARM ioremap() code. I'm not convinced with the
primary arguments for this, but it's been around for a while, and
people seem happy with it - and the "other" justification for this is
at
http://lkml.org/lkml/2012/12/6/184
- Add SCHED_HRTICK to ARMs Kconfig
- Making the ARM SHA/AES code Thumb-2 compatible
- A collection of other small updates.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (26 commits)
ARM: add SCHED_HRTICK config option
ARM: 7650/1: mm: replace direct access to mm->context.id with new macro
ARM: 7649/1: mm: mm->context.id fix for big-endian
ARM: 7648/1: pci: Allow passing per-controller private data
ARM: 7647/1: pci: Keep pci_common_init() around after init
ARM: fix warnings introduced by previous patch
ARM: 7646/1: mm: use static_vm for managing static mapped areas
ARM: 7645/1: ioremap: introduce an infrastructure for static mapped area
ARM: 7644/1: vmregion: remove vmregion code entirely
MAINTAINERS: Re-assert MMCI driver maintainer status
MAINTAINERS: add additional file for MMCI driver
MAINTAINERS: add maintainer entry for AMBA serial drivers
ARM: 7637/1: memory: use SZ_ constants for defining the virtual memory layout
ARM: 7643/1: sched: correct update_sched_clock()
ARM: 7635/1: versatile: fix the PCI IRQ regression
ARM: 7639/1: cache-l2x0: add missed dummy outer_resume entry
ARM: 7630/1: mmc: mmci: Fixup and cleanup code for DMA handling
ARM: 7632/1: spinlock: avoid exclusive accesses on unlock() path
ARM: 7631/1: mmc: mmci: Add new VE MMCI variant
ARM: 7623/1: mmc: mmci: Fixup clock gating when freq is 0 for ST-variants
...
Linus Torvalds [Wed, 20 Feb 2013 22:27:00 +0000 (14:27 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k update from Geert Uytterhoeven.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Sort out !CONFIG_MMU_SUN3 vs. CONFIG_HAS_DMA
swim: Add missing spinlock init
Sam Ravnborg [Fri, 15 Feb 2013 14:52:06 +0000 (15:52 +0100)]
sparc32: refactor smp boot
Introduce a common smp_callin() function to call
from trampoline_32.S.
Add platform specific functions to handle the
platform details.
This is in preparation for a patch that will
unify the smp boot stuff for all architectures.
sparc32 was significantly different to warrant
this patch in preparation.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: David S. Miller <davem@davemloft.net> Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com> Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: fix race condition regarding dst->expires and dst->from.
Eric Dumazet wrote:
| Some strange crashes happen in rt6_check_expired(), with access
| to random addresses.
|
| At first glance, it looks like the RTF_EXPIRES and
| stuff added in commit 1716a96101c49186b
| (ipv6: fix problem with expired dst cache)
| are racy : same dst could be manipulated at the same time
| on different cpus.
|
| At some point, our stack believes rt->dst.from contains a dst pointer,
| while its really a jiffie value (as rt->dst.expires shares the same area
| of memory)
|
| rt6_update_expires() should be fixed, or am I missing something ?
|
| CC Neil because of https://bugzilla.redhat.com/show_bug.cgi?id=892060
Because we do not have any locks for dst_entry, we cannot change
essential structure in the entry; e.g., we cannot change reference
to other entity.
To fix this issue, split 'from' and 'expires' field in dst_entry
out of union. Once it is 'from' is assigned in the constructor,
keep the reference until the very last stage of the life time of
the object.
Of course, it is unsafe to change 'from', so make rt6_set_from simple
just for fresh entries.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Reported-by: Neil Horman <nhorman@tuxdriver.com> CC: Gao Feng <gaofeng@cn.fujitsu.com> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Reported-by: Steinar H. Gunderson <sesse@google.com> Reviewed-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
skb1 is the new skb, therefore should be on the left side of the assignment.
This patch fixes it.
Cc: Pravin B Shelar <pshelar@nicira.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 20 Feb 2013 19:28:50 +0000 (11:28 -0800)]
Merge tag 'edac_3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"Mostly AMD's side of EDAC. It is basically a new family enablement
stuff: AMD F16h MCE decoding enablement from Jacob Shin. The rest is
trivial cleanups."
* tag 'edac_3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
mpc85xx_edac: Fix typo
EDAC, MCE, AMD: Remove unneeded exports
EDAC, MCE, AMD: Add MCE decoding support for Family 16h
EDAC, MCE, AMD: Make MC2 decoding per-family
amd64_edac: Remove dead code
Linus Torvalds [Wed, 20 Feb 2013 19:26:56 +0000 (11:26 -0800)]
Merge tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Rework of the ACPI namespace scanning code from Rafael J. Wysocki
with contributions from Bjorn Helgaas, Jiang Liu, Mika Westerberg,
Toshi Kani, and Yinghai Lu.
- ACPI power resources handling and ACPI device PM update from Rafael
J Wysocki.
- ACPICA update to version 20130117 from Bob Moore and Lv Zheng with
contributions from Aaron Lu, Chao Guan, Jesper Juhl, and Tim Gardner.
- Support for Intel Lynxpoint LPSS from Mika Westerberg.
- cpuidle update from Len Brown including Intel Haswell support, C1
state for intel_idle, removal of global pm_idle.
- cpuidle fixes and cleanups from Daniel Lezcano.
- cpufreq fixes and cleanups from Viresh Kumar and Fabio Baltieri with
contributions from Stratos Karafotis and Rickard Andersson.
- Intel P-states driver for Sandy Bridge processors from Dirk
Brandewie.
- cpufreq driver for Marvell Kirkwood SoCs from Andrew Lunn.
- cpufreq fixes related to ordering issues between acpi-cpufreq and
powernow-k8 from Borislav Petkov and Matthew Garrett.
- cpufreq support for Calxeda Highbank processors from Mark Langsdorf
and Rob Herring.
- cpufreq driver for the Freescale i.MX6Q SoC and cpufreq-cpu0 update
from Shawn Guo.
- cpufreq Exynos fixes and cleanups from Jonghwan Choi, Sachin Kamat,
and Inderpal Singh.
- Support for "lightweight suspend" from Zhang Rui.
- Removal of the deprecated power trace API from Paul Gortmaker.
- Assorted updates from Andreas Fleig, Colin Ian King, Davidlohr Bueso,
Joseph Salisbury, Kees Cook, Li Fei, Nishanth Menon, ShuoX Liu,
Srinivas Pandruvada, Tejun Heo, Thomas Renninger, and Yasuaki
Ishimatsu.
* tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (267 commits)
PM idle: remove global declaration of pm_idle
unicore32 idle: delete stray pm_idle comment
openrisc idle: delete pm_idle
mn10300 idle: delete pm_idle
microblaze idle: delete pm_idle
m32r idle: delete pm_idle, and other dead idle code
ia64 idle: delete pm_idle
cris idle: delete idle and pm_idle
ARM64 idle: delete pm_idle
ARM idle: delete pm_idle
blackfin idle: delete pm_idle
sparc idle: rename pm_idle to sparc_idle
sh idle: rename global pm_idle to static sh_idle
x86 idle: rename global pm_idle to static x86_idle
APM idle: register apm_cpu_idle via cpuidle
cpufreq / intel_pstate: Add kernel command line option disable intel_pstate.
cpufreq / intel_pstate: Change to disallow module build
tools/power turbostat: display SMI count by default
intel_idle: export both C1 and C1E
ACPI / hotplug: Fix concurrency issues and memory leaks
...
Linus Torvalds [Wed, 20 Feb 2013 19:04:46 +0000 (11:04 -0800)]
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree changes from Grant Likely:
"All around device tree changes destined for v3.8. Aside from the
documentation updates the highlights in this branch include:
- Kbuild changes for using CPP with .dts files
- locking fix from preempt_rt patchset
- include DT alias names in device uevent
- Selftest bugfixes and improvements
- New function for counting phandles stanzas in a property
- constify argument to of_node_full_name()
- Various bug fixes
This tree did also contain a commit to use platform_device_add instead
of open-coding the device add code, but it caused problems with amba
devices and needed to be reverted."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (23 commits)
Revert "of: use platform_device_add"
kbuild: limit dtc+cpp include path
gpio: Make of_count_named_gpios() use new of_count_phandle_with_args()
of: Create function for counting number of phandles in a property
of/base: Clean up exit paths for of_parse_phandle_with_args()
of/selftest: Use selftest() macro throughout
of/selftest: Fix GPIOs selftest to cover the 7th case
of: fix recursive locking in of_get_next_available_child()
documentation/devicetree: Fix a typo in exynos-dw-mshc.txt
OF: convert devtree lock from rw_lock to raw spinlock
of/exynos_g2d: Add Bindings for exynos G2D driver
kbuild: create a rule to run the pre-processor on *.dts files
input: Extend matrix-keypad device tree binding
devicetree: Move NS2 LEDs binding into LEDs directory
of: use platform_device_add
powerpc/5200: Fix size to request_mem_region() call
documentation/devicetree: Fix typos
of: add 'const' to of_node_full_name parameter
of: Output devicetree alias names in uevent
DT: add vendor prefixes for Renesas and Toshiba
...
Linus Torvalds [Wed, 20 Feb 2013 19:03:22 +0000 (11:03 -0800)]
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux
Pull SPI changes from Grant Likely:
"Changes to both core spi code and spi device drivers. The driver
changes are the usual set of bug fixes and platform enablement.
Core code changes include:
- More intelligent assignment of SPI bus numbers when using DT
- Common mechanism for using gpios as CS lines
- Pull checks for bits_per_word and transfer speed out of drivers and
into core code
- Ensure temporary DMA buffers are DMA safe"
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux: (50 commits)
spi: Document cs_gpios and cs_gpio in kernel-doc
spi/of: Fix initialization of cs_gpios array
spi/pxa2xx: add support for Lynxpoint SPI controllers
spi/pxa2xx: add support for Intel Low Power Subsystem SPI
spi/pxa2xx: add support for SPI_LOOP
spi/pxa2xx: add support for runtime PM
spi/pxa2xx: add support for DMA engine
spi/pxa2xx: break out the private DMA API usage into a separate file
spi/ath79: add shutdown handler
spi/mips-lantiq: set SPI_MASTER_HALF_DUPLEX flag
spi/mips-lantiq: make use of spi_finalize_current_message
spi/bcm63xx: work around inability to keep CS up
spi/davinci: use request_threaded_irq() to fix deadlock
spi/orion: Use module_platform_driver()
spi/bcm63xx: reject transfers unable to transfer
spi: Ensure memory used for spi_write_then_read() is DMA safe
spi/spi-mpc512x-psc: init mode bits supported by the driver
spi/mpc512x-psc: don't use obsolet cell-index property
spi: Remove erroneous __init, __exit and __exit_p() references in drivers
spi/s3c64xx: fix checkpatch warnings and error
...
Linus Torvalds [Wed, 20 Feb 2013 19:02:10 +0000 (11:02 -0800)]
Merge tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clock framework update from Michael Turquette:
"The common clock framework changes for 3.9 are almost entirely fixes.
None are dire enough to be Cc'd to stable which may be interpreted to
mean that users of the framework are reaching stability. Lots of new
adoption of this framework is via DeviceTree data and that comes
through the respective architecture and platform trees instead of
through the clk framework tree.
Two new features are improved debugfs output and an improvement to how
DT clocks are initialized by reusing a common method."
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux: (25 commits)
clk: sunxi: remove stale Makefile entry
clk: vexpress: Use common of_clk_init() function
clk: zynq: Use common of_clk_init() function
clk: vt8500: Use common of_clk_init() function
clk: highbank: Use common of_clk_init() function
clk: sunxi: Use common of_clk_init() function
clk: add common of_clk_init() function
clk: Deduplicate exit code in clk_set_rate
clk: beautify Makefile
clk-divider: fix macros
clk: prima2: enable dt-binding clkdev mapping
clk: mxs: Index is always positive
clk: max77686: Avoid double free at remove time
clk: remove exported function from __init section
clk: vt8500: Add support for WM8750/WM8850 PLL clocks
clk: vt8500: Fix division-by-0 when requested rate=0
clk: vt8500: Fix device clock divisor calculations
clk: vt8500: Fix error in PLL calculations on non-exact match.
clk: max77686: Remove unnecessary NULL checking for container_of()
clk: JSON debugfs clock tree summary
...
Linus Torvalds [Wed, 20 Feb 2013 19:00:43 +0000 (11:00 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Two new touchpad drivers - Cypress APA I2C Trackpad and Cypress PS/2
touchpad and a big update to ALPS driver from Kevin Cernekee that adds
support for "Rushmore" touchpads and paves way for adding support for
"Dolphin" touchpads.
There is also a new input driver for Goldfish emulator and also
Android keyreset driver was folded into SysRq code.
A few more drivers were updated with device tree bindings and others
got some small cleanups and fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: cyttsp-spi - remove duplicate MODULE_ALIAS()
Input: tsc2005 - add MODULE_ALIAS
Input: tegra-kbc - require CONFIG_OF, remove platform data
Input: synaptics - initialize pointer emulation usage
Input: MT - do not apply filtering on emulated events
Input: bma150 - make some defines public and fix some comments
Input: bma150 - fix checking pm_runtime_get_sync() return value
Input: ALPS - enable trackstick on Rushmore touchpads
Input: ALPS - add support for "Rushmore" touchpads
Input: ALPS - make the V3 packet field decoder "pluggable"
Input: ALPS - move pixel and bitmap info into alps_data struct
Input: ALPS - fix command mode check
Input: ALPS - rework detection of Pinnacle AGx touchpads
Input: ALPS - move {addr,nibble}_command settings into alps_set_defaults()
Input: ALPS - use function pointers for different protocol handlers
Input: ALPS - rework detection sequence
Input: ALPS - introduce helper function for repeated commands
Input: ALPS - move alps_get_model() down below hw_init code
Input: ALPS - copy "model" info into alps_data struct
Input: ALPS - document the alps.h data structures
...
Linus Torvalds [Wed, 20 Feb 2013 18:19:07 +0000 (10:19 -0800)]
Merge tag 'for-v3.9' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Four new drivers:
- goldfish_battery:
This is Android Emulator battery driver. Originally from Google,
but Intel folks reshaped it for mainline
- pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses
AB8500 battery management core
- qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes
- restart-poweroff:
A generic driver that implements 'power off by restarting'. The
actual poweroff functionality is implemented through a bootloader,
so Linux' task is just to restart the box. The driver is useful on
Buffalo Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked
on submitting the driver (as well as qnap-poweroff above).
Additionally:
- A lot of fixes for ab8500 drivers. This is a part of efforts of
syncing internal ST-Ericsson development tree with the mainline.
Lee Jones @ Linaro worked on compilation and reshaping these
series.
- New health properties for the power supplies: "Watchdog timer
expire" and "Safety timer expire"
- As usual, a bunch of fixes/cleanups here and there"
* tag 'for-v3.9' of git://git.infradead.org/battery-2.6: (81 commits)
bq2415x_charger: Add support for offline and 100mA mode
generic-adc-battery: Fix forever loop in gab_remove()
goldfish_battery: Add missing GENERIC_HARDIRQS dependency
da9030_battery: Include notifier.h
bq27x00_battery: Fix reporting battery temperature
power/reset: Remove newly introduced __dev* annotations
lp8727_charger: Small cleanup in naming
ab8500_btemp: Demote initcall sequence
ds2782_battery: Add power_supply_changed() calls for proper uevent support
power: Add battery driver for goldfish emulator
u8500-charger: Delay for USB enumeration
ab8500-bm: Remove individual [charger|btemp|fg|chargalg] pdata structures
ab8500-charger: Do not touch VBUSOVV bits
ab8500-fg: Use correct battery charge full design
pm2301: LPN mode control support
pm2301: Enable vbat low monitoring
ab8500-bm: Flush all work queues before suspending
ab8500-fg: Go to INIT_RECOVERY when charger removed
ab8500-charger: Add support for autopower on AB8505 and AB9540
abx500-chargalg: Add new sysfs interface to get current charge status
...
Fix up fairly straightforward conflicts in the ab8500 driver. But since
it seems to be ARM-specific, I can't even compile-test the result..
David S. Miller [Wed, 20 Feb 2013 06:34:10 +0000 (22:34 -0800)]
sparc64: Fix tsb_grow() in atomic context.
If our first THP installation for an MM is via the set_pmd_at() done
during khugepaged's collapsing we'll end up in tsb_grow() trying to do
a GFP_KERNEL allocation with several locks held.
Simply using GFP_ATOMIC in this situation is not the best option
because we really can't have this fail, so we'd really like to keep
this an order 0 GFP_KERNEL allocation if possible.
Also, doing the TSB allocation from khugepaged is a really bad idea
because we'll allocate it potentially from the wrong NUMA node in that
context.
So what we do is defer the hugepage TSB allocation until the first TLB
miss we take on a hugepage. This is slightly tricky because we have
to handle two unusual cases:
1) Taking the first hugepage TLB miss in the window trap handler.
We'll call the winfix_trampoline when that is detected.
2) An initial TSB allocation via TLB miss races with a hugetlb
fault on another cpu running the same MM. We handle this by
unconditionally loading the TSB we see into the current cpu
even if it's non-NULL at hugetlb_setup time.
Reported-by: Meelis Roos <mroos@ut.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 19 Feb 2013 21:20:08 +0000 (13:20 -0800)]
sparc64: Handle hugepage TSB being NULL.
Accomodate the possibility that the TSB might be NULL at
the point that update_mmu_cache() is invoked. This is
necessary because we will sometimes need to defer the TSB
allocation to the first fault that happens in the 'mm'.
Seperate out the hugepage PTE test into a seperate function
so that the logic is clearer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 20 Feb 2013 17:26:08 +0000 (09:26 -0800)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- New drivers for MAX6697 and compatibles and for INA209.
- Added support for IT8771E, IT8772E, MAX34460, MAX34461, MCP98244, and
ADT7420 to existing drivers.
- Added support for additional attributes to various drivers.
- Replaced SENSORS_LIMIT with clamp_val; retire SENSORS_LIMIT;
- Clean up PMBus code to reduce its size; clean up adt7410 driver.
- A couple of minor bug fixes as well as documentation cleanup.
- Out-of-tree change: Replace SENSORS_LIMIT with clamp_val in
platform/x86/eeepc-laptop driver.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (32 commits)
hwmon: (ntc_thermistor): Fix sparse warnings
hwmon: (adt7410) Add device table entry for the adt7420
hwmon: (adt7410) Use I2C_ADDRS helper macro
hwmon: (adt7410) Use the SIMPLE_DEV_PM_OPS helper macro
hwmon: (adt7410) Let suspend/resume depend on CONFIG_PM_SLEEP
hwmon: (adt7410) Clear unwanted bits in the config register
hwmon: (jc42) Add support for MCP98244
hwmon: (pmbus) Clean up for code size reduction
hwmon: (pmbus/max34440) Add support for MAX34460 and MAX34461
hwmon: (pmbus) Add support for word status register
hwmon: (pmbus/zl6100) Add support for VMON/VDRV
hwmon: (pmbus) Add function to clear sensor cache
hwmon: (pmbus) Add support for additional voltage sensor
hwmon: (pmbus) Use krealloc to allocate attribute memory
hwmon: (pmbus) Simplify memory allocation for sensor attributes
hwmon: (pmbus) Improve boolean handling
hwmon: (pmbus) Simplify memory allocation for labels and booleans
hwmon: (pmbus) Use dev variable to represent client->dev
hwmon: (pmbus) Fix 'Macros with multiple statements' checkpatch error
hwmon: (pmbus) Drop unnecessary error messages in probe error path
...
Linus Torvalds [Wed, 20 Feb 2013 17:23:30 +0000 (09:23 -0800)]
Merge tag 'pinctrl-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"These are the main pinctrl changes for the v3.9 merge window. The
most interesting change by far is how the device core grabs pinctrl
default handles avoiding the need to stick boilerplate into driver
consumers.
- Grabbing of default pinctrl handles from the device core. These
are the hunks hitting drivers/base. All is ACKed by Greg, after a
long discussion about different alternatives.
- Some stuff also touches the MFD and ARM SoC trees, this has been
coordinated and ACKed.
- New drivers for:
- The Tegra 114 sub-SoC
- Allwinner sunxi
- New ABx500 driver and sub-SoC drivers for AB8500, AB8505, AB9540
and AB8540.
- Make it possible for hogged pins to enter a sleep mode, and make it
possible for drivers to control that mode.
- Various clean-up, extensions and device tree support to various pin
controllers."
* tag 'pinctrl-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (68 commits)
pinctrl: tegra: add clfvs function to Tegra114 support
pinctrl: generic: rename input schmitt disable
pinctrl/pinconfig: add debug interface
pinctrl: samsung: remove duplicated line
ARM: ux500: use real AB8500 IRQ numbers instead of virtual ones
ARM: ux500: remove irq_base property from platform_data
pinctrl/abx500: use direct IRQ defines
pinctrl/abx500: replace IRQ offsets with table read-in values
pinctrl/abx500: move IRQ handling to ab8500-core
pinctrl: exynos5440: remove erroneous __init
pinctrl/abx500: adjust offset for get_mode()
pinctrl/abx500: add Device Tree support
pinctrl/abx500: align GPIO cluster boundaries
pinctrl/abx500: prevent error path from corrupting returning error
pinctrl: sunxi: add of_xlate function
pinctrl/lantiq: fix pin number in ltq_pmx_gpio_request_enable
pinctrl/lantiq: add functionality to falcon_pinconf_dbg_show
pinctrl/lantiq: fix pinconfig parameters
pinctrl/lantiq: one of the boot leds was defined incorrectly
pinctrl/lantiq: only probe available pad controllers
...
Linus Torvalds [Wed, 20 Feb 2013 17:22:19 +0000 (09:22 -0800)]
Merge tag 'regulator-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A fairly quiet release for the regulator API, the bulk of the changes
being lots of small cleanups and API updates contributed by Axel Lin
with just a small set of larger changes:
- New driver for LP8755
- DT support for S5M8767, TPS51632, TPS6507x and TPS65090
- Support for writing a "commit changes" bit in the regmap helper
functions."
* tag 'regulator-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (60 commits)
regulator: Fix memory garbage dev_err printout.
regulator: max77686: Reuse rdev_get_id() function.
regulator: tps51632: Use regulator_[get|set]_voltage_sel_regmap
regulator: as3711: Fix checking if no platform initialization data
regulator: s5m8767: Prevent possible NULL pointer dereference
regulator: s5m8767: Fix dev argument for devm_kzalloc and of_get_regulator_init_data
regulator: core: Optimize _regulator_do_set_voltage if voltage does not change
regulator: max8998: Let regulator core handle the case selector == old_selector
regulator: s5m8767: Use of_get_child_count()
regulator: anatop: improve precision of delay time
regulator: show state for GPIO-controlled regulators
regulator: s5m8767: Fix build in non-DT case
regulator: add device tree support for s5m8767
regulator: palmas: Remove a redundant setting for warm_reset
regulator: mc13xxx: Use of_get_child_count()
regulator: max8997: Use of_get_child_count()
regulator: tps65090: Fix using wrong dev argument for calling of_regulator_match
regulators: anatop: add set_voltage_time_sel interface
regulator: Add missing of_node_put()
regulator: tps6507x: Fix using wrong dev argument for calling of_regulator_match
...
Linus Torvalds [Wed, 20 Feb 2013 17:20:55 +0000 (09:20 -0800)]
Merge tag 'regmap-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Several nice new features and performance improvements here,
especially the first:
- Support for using the cache infrastructure without the physical
I/O, allowing devices which don't fit the physical model regmap has
to take advantage of the cache infrastructure, contributed by
Andrey Smirnov.
- Several small improvements to the support for wake capable IRQs.
- Support for asynchronous I/O, allowing us to come much closer to
saturating fast buses like SPI.
- Support for simple array caches, giving higher performance for use
with MMIO devices.
- Restoration of the use of bulk reads for handling interrupts,
giving a performance improvement.
- Support for 24 bit register addresses.
- More performance improvements for debugfs."
* tag 'regmap-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (24 commits)
regmap: mmio: add register clock support
regmap: debugfs: Factor out debugfs_tot_len calc into a function
regmap: debugfs: Optimize seeking within blocks of registers
regmap: debugfs: Add a `max_reg' member in struct regmap_debugfs_off_cache
regmap: debugfs: Fix reading in register field units
regmap: spi: Handle allocation failures gracefully
regmap: Export regmap_async_complete()
regmap: Export regmap_async_complete_cb
regmap: include linux/sched.h to fix build
regmap: spi: Support asynchronous I/O for SPI
regmap: Add asynchronous I/O support
regmap: Add "no-bus" option for regmap API
regmap: regmap: avoid spurious warning in regmap_read_debugfs
regmap: Add provisions to have user-defined write operation
regmap: Add provisions to have user-defined read operation
regmap: Add support for 24 bit wide register addresses
mfd: wm5110: Mark wakes as inverted
mfd: wm5102: Mark wakes as inverted
regmap: irq: Support wake IRQ mask inversion
regmap: irq: Fix sync of wake statuses to hardware
...
Linus Torvalds [Wed, 20 Feb 2013 17:18:31 +0000 (09:18 -0800)]
Merge branch 'for-3.9-cpuset' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cpuset changes from Tejun Heo:
- Synchornization has seen a lot of changes with focus on decoupling
cpuset synchronization from cgroup internal locking.
After this change, there only remain a couple of mostly trivial
dependencies on cgroup_lock outside cgroup core proper. cgroup_lock
is scheduled to be unexported in this devel cycle.
This will finally remove the fragile locking order around cgroup
(cgroup locking wants to / should be one of the outermost but yet has
been acquired from deep inside individual controllers).
- At this point, Li is most knowlegeable with cpuset and taking over
the maintainership of cpuset.
* 'for-3.9-cpuset' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: drop spurious retval assignment in proc_cpuset_show()
cpuset: fix RCU lockdep splat
cpuset: update MAINTAINERS
cpuset: remove cpuset->parent
cpuset: replace cpuset->stack_list with cpuset_for_each_descendant_pre()
cpuset: replace cgroup_mutex locking with cpuset internal locking
cpuset: schedule hotplug propagation from cpuset_attach() if the cpuset is empty
cpuset: pin down cpus and mems while a task is being attached
cpuset: make CPU / memory hotplug propagation asynchronous
cpuset: drop async_rebuild_sched_domains()
cpuset: don't nest cgroup_mutex inside get_online_cpus()
cpuset: reorganize CPU / memory hotplug handling
cpuset: cleanup cpuset[_can]_attach()
cpuset: introduce cpuset_for_each_child()
cpuset: introduce CS_ONLINE
cpuset: introduce ->css_on/offline()
cpuset: remove fast exit path from remove_tasks_in_empty_cpuset()
cpuset: remove unused cpuset_unlock()
Linus Torvalds [Wed, 20 Feb 2013 17:16:21 +0000 (09:16 -0800)]
Merge branch 'for-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup changes from Tejun Heo:
"Nothing too drastic.
- Removal of synchronize_rcu() from userland visible paths.
- Various fixes and cleanups from Li.
- cgroup_rightmost_descendant() added which will be used by cpuset
changes (it will be a separate pull request)."
* 'for-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fail if monitored file and event_control are in different cgroup
cgroup: fix cgroup_rmdir() vs close(eventfd) race
cpuset: fix cpuset_print_task_mems_allowed() vs rename() race
cgroup: fix exit() vs rmdir() race
cgroup: remove bogus comments in cgroup_diput()
cgroup: remove synchronize_rcu() from cgroup_diput()
cgroup: remove duplicate RCU free on struct cgroup
sched: remove redundant NULL cgroup check in task_group_path()
sched: split out css_online/css_offline from tg creation/destruction
cgroup: initialize cgrp->dentry before css_alloc()
cgroup: remove a NULL check in cgroup_exit()
cgroup: fix bogus kernel warnings when cgroup_create() failed
cgroup: remove synchronize_rcu() from rebind_subsystems()
cgroup: remove synchronize_rcu() from cgroup_attach_{task|proc}()
cgroup: use new hashtable implementation
cgroups: fix cgroup_event_listener error handling
cgroups: move cgroup_event_listener.c to tools/cgroup
cgroup: implement cgroup_rightmost_descendant()
cgroup: remove unused dummy cgroup_fork_callbacks()
Linus Torvalds [Wed, 20 Feb 2013 06:10:26 +0000 (22:10 -0800)]
Merge branch 'for-3.9-async' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull async changes from Tejun Heo:
"These are followups for the earlier deadlock issue involving async
ending up waiting for itself through block requesting module[1]. The
following changes are made by these commits.
- Instead of requesting default elevator on each request_queue init,
block now requests it once early during boot.
- Kmod triggers warning if invoked from an async worker.
- Async synchronization implementation has been reimplemented. It's
a lot simpler now."
* 'for-3.9-async' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
async: initialise list heads to fix crash
async: replace list of active domains with global list of pending items
async: keep pending tasks on async_domain and remove async_pending
async: use ULLONG_MAX for infinity cookie value
async: bring sanity to the use of words domain and running
async, kmod: warn on synchronous request_module() from async workers
block: don't request module during elevator init
init, block: try to load default elevator module early during boot
Linus Torvalds [Wed, 20 Feb 2013 06:01:33 +0000 (22:01 -0800)]
Merge branch 'for-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue changes from Tejun Heo:
"A lot of reorganization is going on mostly to prepare for worker pools
with custom attributes so that workqueue can replace custom pool
implementations in places including writeback and btrfs and make CPU
assignment in crypto more flexible.
workqueue evolved from purely per-cpu design and implementation, so
there are a lot of assumptions regarding being bound to CPUs and even
unbound workqueues are implemented as an extension of the model -
workqueues running on the special unbound CPU. Bulk of changes this
round are about promoting worker_pools as the top level abstraction
replacing global_cwq (global cpu workqueue). At this point, I'm
fairly confident about getting custom worker pools working pretty soon
and ready for the next merge window.
Lai's patches are replacing the convoluted mb() dancing workqueue has
been doing with much simpler mechanism which only depends on
assignment atomicity of long. For details, please read the commit
message of 0b3dae68ac ("workqueue: simplify is-work-item-queued-here
test"). While the change ends up adding one pointer to struct
delayed_work, the inflation in percentage is less than five percent
and it decouples delayed_work logic a lot more cleaner from usual work
handling, removes the unusual memory barrier dancing, and allows for
further simplification, so I think the trade-off is acceptable.
There will be two more workqueue related pull requests and there are
some shared commits among them. I'll write further pull requests
assuming this pull request is pulled first."
* 'for-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (37 commits)
workqueue: un-GPL function delayed_work_timer_fn()
workqueue: rename cpu_workqueue to pool_workqueue
workqueue: reimplement is_chained_work() using current_wq_worker()
workqueue: fix is_chained_work() regression
workqueue: pick cwq instead of pool in __queue_work()
workqueue: make get_work_pool_id() cheaper
workqueue: move nr_running into worker_pool
workqueue: cosmetic update in try_to_grab_pending()
workqueue: simplify is-work-item-queued-here test
workqueue: make work->data point to pool after try_to_grab_pending()
workqueue: add delayed_work->wq to simplify reentrancy handling
workqueue: make work_busy() test WORK_STRUCT_PENDING first
workqueue: replace WORK_CPU_NONE/LAST with WORK_CPU_END
workqueue: post global_cwq removal cleanups
workqueue: rename nr_running variables
workqueue: remove global_cwq
workqueue: remove worker_pool->gcwq
workqueue: replace for_each_worker_pool() with for_each_std_worker_pool()
workqueue: make freezing/thawing per-pool
workqueue: make hotplug processing per-pool
...
Linus Torvalds [Wed, 20 Feb 2013 05:58:52 +0000 (21:58 -0800)]
Merge branch 'for-3.9-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue [delayed_]work_pending() cleanups from Tejun Heo:
"This is part of on-going cleanups to remove / minimize usages of
workqueue interfaces which are deprecated and/or misleading.
This round drops a number of usages of [delayed_]work_pending(), which
are dangerous as they lack any form of synchronization and thus often
lead to buggy / unnecessary code. There are a couple legitimate use
cases in kernel. Hopefully, they can be converted and
[delayed_]work_pending() can be removed completely. Even if not,
removing most of misuses should make it more difficult to find
examples of misuses and thus slow down growth of them.
These changes are independent from other workqueue changes."
* 'for-3.9-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
wimax/i2400m: fix i2400m->wake_tx_skb handling
kprobes: fix wait_for_kprobe_optimizer()
ipw2x00: simplify scan_event handling
video/exynos: don't use [delayed_]work_pending()
tty/max3100: don't use [delayed_]work_pending()
x86/mce: don't use [delayed_]work_pending()
rfkill: don't use [delayed_]work_pending()
wl1251: don't use [delayed_]work_pending()
thinkpad_acpi: don't use [delayed_]work_pending()
mwifiex: don't use [delayed_]work_pending()
sja1000: don't use [delayed_]work_pending()
Linus Torvalds [Wed, 20 Feb 2013 04:12:57 +0000 (20:12 -0800)]
Merge branch 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 UV3 support update from Ingo Molnar:
"Support for the SGI Ultraviolet System 3 (UV3) platform - the upcoming
third major iteration and upscaling of the SGI UV supercomputing
platform."
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, uv, uv3: Trim MMR register definitions after code changes for SGI UV3
x86, uv, uv3: Check current gru hub support for SGI UV3
x86, uv, uv3: Update Time Support for SGI UV3
x86, uv, uv3: Update x2apic Support for SGI UV3
x86, uv, uv3: Update Hub Info for SGI UV3
x86, uv, uv3: Update ACPI Check to include SGI UV3
x86, uv, uv3: Update MMR register definitions for SGI Ultraviolet System 3 (UV3)
Linus Torvalds [Wed, 20 Feb 2013 04:11:07 +0000 (20:11 -0800)]
Merge branch 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 platform changes from Ingo Molnar:
- Support for the Technologic Systems TS-5500 platform, by Vivien
Didelot
- Improved NUMA support on AMD systems:
Add support for federated systems where multiple memory controllers
can exist and see each other over multiple PCI domains. This
basically means that AMD node ids can be more than 8 now and the code
handling this is taught to incorporate PCI domain into those IDs.
- Support for the Goldfish virtual Android emulator, by Jun Nakajima,
Intel, Google, et al.
- Misc fixlets.
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Add TS-5500 platform support
x86/srat: Simplify memory affinity init error handling
x86/apb/timer: Remove unnecessary "if"
goldfish: platform device for x86
amd64_edac: Fix type usage in NB IDs and memory ranges
amd64_edac: Fix PCI function lookup
x86, AMD, NB: Use u16 for northbridge IDs in amd_get_nb_id
x86, AMD, NB: Add multi-domain support
Linus Torvalds [Wed, 20 Feb 2013 04:10:21 +0000 (20:10 -0800)]
Merge branch 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/hyperv changes from Ingo Molnar:
"The biggest change is support for Windows 8's improved hypervisor
interrupt model on the Linux Hyper-V guest subsystem code side.
Smallish fixes otherwise."
* 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, hyperv: HYPERV depends on X86_LOCAL_APIC
X86: Handle Hyper-V vmbus interrupts as special hypervisor interrupts
X86: Add a check to catch Xen emulation of Hyper-V
x86: Hyper-V: register clocksource only if its advertised
Linus Torvalds [Wed, 20 Feb 2013 04:09:48 +0000 (20:09 -0800)]
Merge branch 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/debug changes from Ingo Molnar:
"Two init annotations and a built-in memtest speedup"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/memtest: Shorten time for tests
x86: Convert a few mistaken __cpuinit annotations to __init
x86/EFI: Properly init-annotate BGRT code
David S. Miller [Wed, 20 Feb 2013 03:24:50 +0000 (22:24 -0500)]
Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
One last batch of stragglers intended for 3.9...
For the iwlwifi pull, Johannes says:
"I hadn't expected to ask you to pull iwlwifi-next again, but I have a
number of fixes most of which I'd also send in after rc1, so here it is.
The first commit is a merge error between mac80211-next and
iwlwifi-next; in addition I have fixes for P2P scanning and MVM driver
MAC (virtual interface) management from Ilan, a CT-kill (critical
temperature) fix from Eytan, and myself fixed three different little but
annoying bugs in the MVM driver.
The only ones I might not send for -rc1 are Emmanuel's debug patch, but
OTOH it should help greatly if there are any issues, and my own time
event debugging patch that I used to find the race condition but we
decided to keep it for the future."
For the mac80211 pull, Johannes says:
"Like iwlwifi-next, this would almost be suitable for rc1.
I have a fix for station management on non-TDLS drivers, a CAB queue
crash fix for mesh, a fix for an annoying (but harmless) warning, a
tracing fix and a documentation fix. Other than that, only a few mesh
cleanups."
Along with that is a fix for memory corruption in rtlwifi, an
orinoco_usb fix to avoid allocating a DMA buffer on the stack, an a
hostap fix to return -ENOMEM instead of -1 after a memory allocation
failure. The remaining bits implement 802.11ac support for the mwifiex
driver -- I think that is still worth getting into 3.9.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 19 Feb 2013 12:14:10 +0000 (12:14 +0000)]
ip_gre: remove an extra dst_release()
commit 68c331631143 (v4 GRE: Add TCP segmentation offload for GRE)
introduced a bug in error path.
dst is attached to skb, so will be released when skb is freed.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Pravin B Shelar <pshelar@nicira.com> Acked-by: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 20 Feb 2013 03:13:49 +0000 (19:13 -0800)]
Merge branch 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanup patches from Ingo Molnar:
"Misc smaller cleanups"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: ptrace.c only needs export.h and not the full module.h
x86, apb_timer: remove unused variable percpu_timer
um: don't compare a pointer to 0
arch/x86/platform/uv: use ARRAY_SIZE where possible
Linus Torvalds [Wed, 20 Feb 2013 03:12:03 +0000 (19:12 -0800)]
Merge branch 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull two x86 kernel build changes from Ingo Molnar:
"The first change modifies how 'make oldconfig' works on cross-bitness
situations on x86. It was felt the new behavior of preserving the
bitness of the .config is more logical. This is a leftover of the
merge.
The second change eliminates a Perl warning. (There's another, more
complete fix resulting of this warning fix, which second fix in flight
to you via the kbuild tree, which will remove the timeconst.pl script
altogether.)"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timeconst.pl: Eliminate Perl warning
x86: Default to ARCH=x86 to avoid overriding CONFIG_64BIT
Linus Torvalds [Wed, 20 Feb 2013 03:11:10 +0000 (19:11 -0800)]
Merge branch 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 bootup changes from Ingo Molnar:
"Deal with bootloaders which fail to initialize unknown fields in
boot_params to zero, by sanitizing boot params passed in.
This unbreaks versions of kexec-utils. Other bootloaders do not
appear to show sensitivity to this change, but it's a possibility for
breakage nevertheless."
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Sanitize boot_params if not zeroed on creation
Linus Torvalds [Wed, 20 Feb 2013 03:09:42 +0000 (19:09 -0800)]
Merge branch 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/asm changes from Ingo Molnar:
"The biggest change (by line count) is the unification of the XOR code
and then the introduction of an additional SSE based XOR assembly
method.
The other bigger change is the head_32.S rework/cleanup by Borislav
Petkov.
Last but not least there's the usual laundry list of small but
dangerous (and hopefully perfectly tested) changes to subtle low level
x86 code, plus cleanups."
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, head_32: Give the 6 label a real name
x86, head_32: Remove second CPUID detection from default_entry
x86: Detect CPUID support early at boot
x86, head_32: Remove i386 pieces
x86: Require MOVBE feature in cpuid when we use it
x86: Enable ARCH_USE_BUILTIN_BSWAP
x86/xor: Add alternative SSE implementation only prefetching once per 64-byte line
x86/xor: Unify SSE-base xor-block routines
x86: Fix a typo
x86/mm: Fix the argument passed to sync_global_pgds()
x86/mm: Convert update_mmu_cache() and update_mmu_cache_pmd() to functions
ix86: Tighten asmlinkage_protect() constraints
Linus Torvalds [Wed, 20 Feb 2013 03:07:27 +0000 (19:07 -0800)]
Merge branch 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/apic changes from Ingo Molnar:
"Main changes:
- Multiple MSI support added to the APIC, PCI and AHCI code - acked
by all relevant maintainers, by Alexander Gordeev.
The advantage is that multiple AHCI ports can have multiple MSI
irqs assigned, and can thus spread to multiple CPUs.
[ Drivers can make use of this new facility via the
pci_enable_msi_block_auto() method ]
- x86 IOAPIC code from interrupt remapping cleanups from Joerg
Roedel:
These patches move all interrupt remapping specific checks out of
the x86 core code and replaces the respective call-sites with
function pointers. As a result the interrupt remapping code is
better abstraced from x86 core interrupt handling code.
- Various smaller improvements, fixes and cleanups."
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess
x86, kvm: Fix intialization warnings in kvm.c
x86, irq: Move irq_remapped out of x86 core code
x86, io_apic: Introduce eoi_ioapic_pin call-back
x86, msi: Introduce x86_msi.compose_msi_msg call-back
x86, irq: Introduce setup_remapped_irq()
x86, irq: Move irq_remapped() check into free_remapped_irq
x86, io-apic: Remove !irq_remapped() check from __target_IO_APIC_irq()
x86, io-apic: Move CONFIG_IRQ_REMAP code out of x86 core
x86, irq: Add data structure to keep AMD specific irq remapping information
x86, irq: Move irq_remapping_enabled declaration to iommu code
x86, io_apic: Remove irq_remapping_enabled check in setup_timer_IRQ0_pin
x86, io_apic: Move irq_remapping_enabled checks out of check_timer()
x86, io_apic: Convert setup_ioapic_entry to function pointer
x86, io_apic: Introduce set_affinity function pointer
x86, msi: Use IRQ remapping specific setup_msi_irqs routine
x86, hpet: Introduce x86_msi_ops.setup_hpet_msi
x86, io_apic: Introduce x86_io_apic_ops.print_entries for debugging
x86, io_apic: Introduce x86_io_apic_ops.disable()
x86, apic: Mask IO-APIC and PIC unconditionally on LAPIC resume
...
Linus Torvalds [Wed, 20 Feb 2013 03:05:45 +0000 (19:05 -0800)]
Merge branch 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer changes from Ingo Molnar:
"Main changes:
- ntp: Add CONFIG_RTC_SYSTOHC: a generic RTC driver facility
complementing the existing CONFIG_RTC_HCTOSYS, which uses NTP to
keep the hardware clock updated.
- posix-timers: Fix clock_adjtime to always return timex data on
success. This is changing the ABI, but no breakage was expected
and found - caution is warranted nevertheless.
- clockevents: refactor timer broadcast handling to be more generic
and less duplicated with matching architecture code (mostly ARM
motivated.)
- various fixes and cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers/x86/hpet: Use HPET_COUNTER to specify the hpet counter in vread_hpet()
posix-cpu-timers: Fix nanosleep task_struct leak
clockevents: Fix generic broadcast for FEAT_C3STOP
time, Fix setting of hardware clock in NTP code
hrtimer: Prevent hrtimer_enqueue_reprogram race
clockevents: Add generic timer broadcast function
clockevents: Add generic timer broadcast receiver
timekeeping: Switch HAS_PERSISTENT_CLOCK to ALWAYS_USE_PERSISTENT_CLOCK
x86/time/rtc: Don't print extended CMOS year when reading RTC
x86: Select HAS_PERSISTENT_CLOCK on x86
timekeeping: Add CONFIG_HAS_PERSISTENT_CLOCK option
rtc: Skip the suspend/resume handling if persistent clock exist
timekeeping: Add persistent_clock_exist flag
posix-timers: Fix clock_adjtime to always return timex data on success
Round the calculated scale factor in set_cyc2ns_scale()
NTP: Add a CONFIG_RTC_SYSTOHC configuration
MAINTAINERS: Update John Stultz's email
time: create __getnstimeofday for WARNless calls
Linus Torvalds [Wed, 20 Feb 2013 03:04:55 +0000 (19:04 -0800)]
Merge branch 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull preparatory smp/hotplug patches from Ingo Molnar:
"Some early preparatory changes for the WIP hotplug rework by Thomas
Gleixner."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stop_machine: Use smpboot threads
stop_machine: Store task reference in a separate per cpu variable
smpboot: Allow selfparking per cpu threads
Linus Torvalds [Wed, 20 Feb 2013 02:19:48 +0000 (18:19 -0800)]
Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler changes from Ingo Molnar:
"Main changes:
- scheduler side full-dynticks (user-space execution is undisturbed
and receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready, from Frederic
Weisbecker.
- Initial sched.h split-up changes, by Clark Williams
- select_idle_sibling() performance improvement by Mike Galbraith:
" 1 tbench pair (worst case) in a 10 core + SMT package:
pre 15.22 MB/sec 1 procs
post 252.01 MB/sec 1 procs "
- sched_rr_get_interval() ABI fix/change. We think this detail is not
used by apps (so it's not an ABI in practice), but lets keep it
under observation.
- misc RT scheduling cleanups, optimizations"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched/rt: Add <linux/sched/rt.h> header to <linux/init_task.h>
cputime: Remove irqsave from seqlock readers
sched, powerpc: Fix sched.h split-up build failure
cputime: Restore CPU_ACCOUNTING config defaults for PPC64
sched/rt: Move rt specific bits into new header file
sched/rt: Add a tuning knob to allow changing SCHED_RR timeslice
sched: Move sched.h sysctl bits into separate header
sched: Fix signedness bug in yield_to()
sched: Fix select_idle_sibling() bouncing cow syndrome
sched/rt: Further simplify pick_rt_task()
sched/rt: Do not account zero delta_exec in update_curr_rt()
cputime: Safely read cputime of full dynticks CPUs
kvm: Prepare to add generic guest entry/exit callbacks
cputime: Use accessors to read task cputime stats
cputime: Allow dynamic switch between tick/virtual based cputime accounting
cputime: Generic on-demand virtual cputime accounting
cputime: Move default nsecs_to_cputime() to jiffies based cputime file
cputime: Librarize per nsecs resolution cputime definitions
cputime: Avoid multiplication overflow on utime scaling
context_tracking: Export context state for generic vtime
...
Fix up conflict in kernel/context_tracking.c due to comment additions.
Linus Torvalds [Wed, 20 Feb 2013 01:49:41 +0000 (17:49 -0800)]
Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf changes from Ingo Molnar:
"There are lots of improvements, the biggest changes are:
Main kernel side changes:
- Improve uprobes performance by adding 'pre-filtering' support, by
Oleg Nesterov.
- Make some POWER7 events available in sysfs, equivalent to what was
done on x86, from Sukadev Bhattiprolu.
- tracing updates by Steve Rostedt - mostly misc fixes and smaller
improvements.
- Use perf/event tracing to report PCI Express advanced errors, by
Tony Luck.
- Enable northbridge performance counters on AMD family 15h, by Jacob
Shin.
- This tracing commit:
tracing: Remove the extra 4 bytes of padding in events
changes the ABI. All involved parties (PowerTop in particular)
seem to agree that it's safe to do now with the introduction of
libtraceevent, but the devil is in the details ...
Main tooling side changes:
- Add 'event group view', from Namyung Kim:
To use it, 'perf record' should group events when recording. And
then perf report parses the saved group relation from file header
and prints them together if --group option is provided. You can
use the 'perf evlist' command to see event group information:
$ perf record -e '{ref-cycles,cycles}' noploop 1
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.385 MB perf.data (~16807 samples) ]
$ perf evlist --group
{ref-cycles,cycles}
With this example, default perf report will show you each event
separately.
You can use --group option to enable event group view:
As you can see the Overhead column now contains both of ref-cycles
and cycles and header line shows group information also - 'anon
group { ref-cycles, cycles }'. The output is sorted by period of
group leader first.
- Initial GTK+ annotate browser, from Namhyung Kim.
- Add option for runtime switching perf data file in perf report,
just press 's' and a menu with the valid files found in the current
directory will be presented, from Feng Tang.
- Add support to display whole group data for raw columns, from Jiri
Olsa.
- Add per processor socket count aggregation in perf stat, from
Stephane Eranian.
- Add interval printing in 'perf stat', from Stephane Eranian.
- 'perf test' improvements
- Add support for wildcards in tracepoint system name, from Jiri
Olsa.
- Add anonymous huge page recognition, from Joshua Zhu.
- perf build-id cache now can show DSOs present in a perf.data file
that are not in the cache, to integrate with build-id servers being
put in place by organizations such as Fedora.
- perf top now shares more of the evsel config/creation routines with
'record', paving the way for further integration like 'top'
snapshots, etc.
- perf top now supports DWARF callchains.
- Fix mmap limitations on 32-bit, fix from David Miller.
- 'perf bench numa mem' NUMA performance measurement suite
- ... and lots of fixes, performance improvements, cleanups and other
improvements I failed to list - see the shortlog and git log for
details."
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (270 commits)
perf/x86/amd: Enable northbridge performance counters on AMD family 15h
perf/hwbp: Fix cleanup in case of kzalloc failure
perf tools: Fix build with bison 2.3 and older.
perf tools: Limit unwind support to x86 archs
perf annotate: Make it to be able to skip unannotatable symbols
perf gtk/annotate: Fail early if it can't annotate
perf gtk/annotate: Show source lines with gray color
perf gtk/annotate: Support multiple event annotation
perf ui/gtk: Implement basic GTK2 annotation browser
perf annotate: Fix warning message on a missing vmlinux
perf buildid-cache: Add --update option
uprobes/perf: Avoid uprobe_apply() whenever possible
uprobes/perf: Teach trace_uprobe/perf code to use UPROBE_HANDLER_REMOVE
uprobes/perf: Teach trace_uprobe/perf code to pre-filter
uprobes/perf: Teach trace_uprobe/perf code to track the active perf_event's
uprobes: Introduce uprobe_apply()
perf: Introduce hw_perf_event->tp_target and ->tp_list
uprobes/perf: Always increment trace_uprobe->nhit
uprobes/tracing: Kill uprobe_trace_consumer, embed uprobe_consumer into trace_uprobe
uprobes/tracing: Introduce is_trace_uprobe_enabled()
...
Linus Torvalds [Wed, 20 Feb 2013 01:47:58 +0000 (17:47 -0800)]
Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq core changes from Ingo Molnar:
"The biggest changes are the IRQ-work and printk changes from Frederic
Weisbecker, which prepare the code for 'full dynticks' (the ability to
stop or slow down the periodic tick arbitrarily, not just in idle time
as today):
- Don't stop tick with irq works pending. This fix is generally
useful and concerns archs that can't raise self IPIs.
- Flush irq works before CPU offlining.
- Introduce "lazy" irq works that can wait for the next tick to be
executed, unless it's stopped.
- Implement klogd wake up using irq work. This removes the ad-hoc
printk_tick()/printk_needs_cpu() hooks and make it working even in
dynticks mode.
- Cleanups and fixes."
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Export enable/disable_percpu_irq()
arch Kconfig: Remove references to IRQ_PER_CPU
irq_work: Remove return value from the irq_work_queue() function
genirq: Avoid deadlock in spurious handling
printk: Wake up klogd using irq_work
irq_work: Make self-IPIs optable
irq_work: Warn if there's still work on cpu_down
irq_work: Flush work on CPU_DYING
irq_work: Don't stop the tick with pending works
nohz: Add API to check tick state
irq_work: Remove CONFIG_HAVE_IRQ_WORK
irq_work: Fix racy check on work pending flag
irq_work: Fix racy IRQ_WORK_BUSY flag setting
Linus Torvalds [Wed, 20 Feb 2013 01:45:20 +0000 (17:45 -0800)]
Merge branch 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU changes from Ingo Molnar:
"SRCU changes:
- These include debugging aids, updates that move towards the goal of
permitting srcu_read_lock() and srcu_read_unlock() to be used from
idle and offline CPUs, and a few small fixes.
Changes to rcutorture and to RCU documentation:
- Posted to LKML at https://lkml.org/lkml/2013/1/26/188
Enhancements to uniprocessor handling in tiny RCU:
- Posted to LKML at https://lkml.org/lkml/2013/1/27/2
Tag RCU callbacks with grace-period number to simplify callback
advancement:
- Posted to LKML at https://lkml.org/lkml/2013/1/26/203
Miscellaneous fixes:
- Posted to LKML at https://lkml.org/lkml/2013/1/26/204"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
srcu: use ACCESS_ONCE() to access sp->completed in srcu_read_lock()
srcu: Update synchronize_srcu_expedited()'s comments
srcu: Update synchronize_srcu()'s comments
srcu: Remove checks preventing idle CPUs from calling srcu_read_lock()
srcu: Remove checks preventing offline CPUs from calling srcu_read_lock()
srcu: Simple cleanup for cleanup_srcu_struct()
srcu: Add might_sleep() annotation to synchronize_srcu()
srcu: Simplify __srcu_read_unlock() via this_cpu_dec()
rcu: Allow rcutorture to be built at low optimization levels
rcu: Make rcutorture's shuffler task shuffle recently added tasks
rcu: Allow TREE_PREEMPT_RCU on UP systems
rcu: Provide RCU CPU stall warnings for tiny RCU
context_tracking: Add comments on interface and internals
rcu: Remove obsolete Kconfig option from comment
rcu: Remove unused code originally used for context tracking
rcu: Consolidate debugging Kconfig options
rcu: Correct 'optimized' to 'optimize' in header comment
rcu: Trace callback acceleration
rcu: Tag callback lists with corresponding grace-period number
rcutorture: Don't compare ptr with 0
...
Sachin Kamat [Tue, 19 Feb 2013 09:37:34 +0000 (15:07 +0530)]
hwmon: (ntc_thermistor): Fix sparse warnings
Fixes the following sparse warnings:
drivers/hwmon/ntc_thermistor.c:46:31: warning:
symbol 'ncpXXwb473' was not declared. Should it be static?
drivers/hwmon/ntc_thermistor.c:82:31: warning:
symbol 'ncpXXwl333' was not declared. Should it be static?
Cc: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon: (adt7410) Let suspend/resume depend on CONFIG_PM_SLEEP
Only build the suspend/resume code if CONFIG_PM_SLEEP is selected. Currently the
code is built if CONFIG_PM is selected, but it will also be selected if only
runtime PM support is built into the kernel.
hwmon: (adt7410) Clear unwanted bits in the config register
Make sure to clear the mode bits from the config register before setting the new
mode. Otherwise we might end up with a different mode than we want to.
Eric Dumazet [Tue, 19 Feb 2013 18:42:03 +0000 (10:42 -0800)]
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
If a qdisc is installed on a ppp device, its possible to get
a lockdep splat under stress, because nested dev_queue_xmit() can
lock busylock a second time (on a different device, so its a false
positive)
Avoid this problem using a distinct lock_class_key for ppp
devices.
Reported-by: Yanko Kaneti <yaneti@declera.com> Tested-by: Yanko Kaneti <yaneti@declera.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>