This patch introduces viafb_shared and is the beginning of a smooth
transition to use it.
viafb_shared should contain all general, non-surface specific data that
should be shared along all viafb framebuffers while viafb_par should only
contain things that are specific to each surface or in other words extend
fb_info. This change is intended to clean the dual/multi framebuffer
handling up.
This removes the annoyance that viafbinfo1->par points to a different
structure than viaparinfo1.
As the last change is fundamental it is difficult to ensure that all parts
of the driver do not depend on the previous brokenness but the chance of
regressions is very low.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This removes the completly useless io variable as well as the temporary
used variables mmio_base and mmio_len in favor to use directly the fb_info
variables.
This is a code cleanup only, no runtime change expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At least for VX800 this initialization is not very good as some parts of
the register are written with reserved values. This makes the display go
white in some configurations and not usable until the framebuffer is
removed. It's better to not initialize it as it allows to use a
previously (by BIOS) correctly configured display.
This patch makes some displays work but might cause problems on others.
This is bad but can not be easily avoided. If this causes some
regressions it's probably the best to fix it in the 'active' display setup
code.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove everything related to video devices from the driver as it did not
influence the driver operation. This patch does change the userspace
behaviour as it removes two IOCTLs and one module parameter. But this is
good as it removes useless stuff and helps the user to figure out the
options that do affect the driver behaviour (which are still too many).
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean the handling of ioremapped video memory up. The following changes
were made:
info->screen_base - viafb_FB_MM
(VRAM offset calculation) was replaced by
info->fix.smem_start - viafbinfo->fix.smem_start
which is essentially the same calculation but done with physical instead
virtual addresses.
*->fbmem_virt
was replaced by
viafbinfo->screen_base
This is true for viafbinfo and viafbinfo1 as the par pointers are equal.
An early initialization of viafbinfo1->fix.smem* was removed as done later
in viafb_setup_fixinfo.
This patch highlights that the only usage of the ioremapped video memory
in the driver is for hardware cursor handling. Even if it has to hold the
used virtual screen mapped for old-fashioned read/write calls (vs.
mmap'ed) a lot virtual memory could be saved by only ioremapping on
demand.
Code cleanup, no runtime changes expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean the duoview handling up by replacing the varible with the funtion in
the only place where it is used. This is a code cleanup only, no runtime
change expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the mode information from viafbdev.c and uses the one of viamode.c
instead. This is possible because horizontal and vertical address are the
same as horizontal and vertical resolution. The reduced blanking modes in
the table are no problem because they have a higher index than the normal
modes and therefore always the normal modes are selected just as the old
behaviour.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unneeeded declarations from the header and makes it more
maintainable by evaluating the array size in the file the array exist in
and exporting it via variables. This removes the need to keep the array
size in the header in sync with the real array size.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct the returned error code for remapping the video framebuffer.
Introduce error handling for remapping MMIO register address space to
avoid a NULL pointer dereference. Disable hardware acceleration if
remapping MMIO register address space failed as those registers are only
used for hardware acceleration.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move individual start address setting to viafb_set_primary_address and
viafb_set_secondary_address and make it more flexible to reuse it for
panning. Using central functions makes it easier to follow HW
manipulations.
Remove crt locking as it should be only needed for timing manipulation.
Move iga_path manipulation to via_pci_probe.
Remove memset for screen cleaning as it is currently done only for the
second screen. This is not needed for normal operation but has a little
chance of causing unwanted display artifacts. This can be fixed later
more consistent and more efficient (using viafb_fillrect) if needed.
This is a code clenup, no notable runtime changes expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
viafb: merge viafb_update_viafb_par in viafb_update_fix
Shrink and merge viafb_update_viafb_par. This removes a lot of duplicated
data in viafb_par. Use the relevant data of fb_info instead. On the way
it removes an inconsistency in handling a second framebuffer which only
worked because viafbinfo1->par is modified to point to the same viafb_par
as viafbinfo->par.
Code cleanup only, no runtime change expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the start address is set to an initial value every time
viafb_setmode is called.
This is not done consistently along graphic cores and not even the whole
address but often only parts of it. On top of that it seems useless as
the real/final address will be set by viafb_set_start_addr a few lines
later.
Remove this superfluous initalization to shrink register initalization and
as a start to decouple primary and secondary display. Code cleanup, no
notable runtime change expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Cc: Scott Fang <ScottFang@viatech.com.cn> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Harald Welte <laforge@gnumonks.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ryan Mallon [Tue, 22 Sep 2009 23:47:09 +0000 (16:47 -0700)]
ep93xx video driver
EP93xx video driver plus documentation.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Daniele Venzano <linux@brownhat.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ryan Mallon [Tue, 22 Sep 2009 23:47:09 +0000 (16:47 -0700)]
ep93xx video driver platform support
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Daniele Venzano <linux@brownhat.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If called with mode_idx = 1, rate = 68, a read occurs from
sisfb_vrate[-1].refresh.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Cc: Thomas Winischhofer <thomas@winischhofer.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
davinci: fb: Frame Buffer driver for TI DA8xx/OMAP-L1xx
Add LCD controller (LCDC) driver for TI's DA8xx/OMAP-L1xx architecture.
LCDC specifications can be found at http://www.ti.com/litv/pdf/sprufm0a.
LCDC on DA8xx consists of two independent controllers, the Raster
Controller and the LCD Interface Display Driver (LIDD) controller. LIDD
further supports character and graphic displays.
This patch adds support for the graphic display (Sharp LQ035Q3DG01) found
on the DA830 based EVM. The EVM details can be found at:
http://support.spectrumdigital.com/boards/dskda830/revc/.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com> Signed-off-by: Steve Chen <schen@mvista.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
DESC
davinci-fb-frame-buffer-driver-for-ti-da8xx-omap-l1xx-fix
EDESC
From: Andrew Morton <akpm@linux-foundation.org>
fix kconfig indenting
Cc: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com> Cc: Steve Chen <schen@mvista.com> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Machek [Tue, 22 Sep 2009 23:47:03 +0000 (16:47 -0700)]
fbdev: framebuffer support for HTC Dream
Add a framebuffer driver for Qualcomm MSM/QSD SoCs, tested on HTC Dream
smartphone (aka T-Mobile G1, aka ADP1).
Brian said:
I did the original quick and dirty version for bringup. Rebecca took
over and (re)wrote the bulk of the driver, getting things stable for
production ship of Dream and Sapphire, and Dima is currently adding
support for later Qualcomm chipsets (QSD8x50, etc).
Signed-off-by: Pavel Machek <pavel@ucw.cz> Cc: Brian Swetland <swetland@google.com> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Cc: Rebecca Schultz Zavin <rebecca@android.com> Cc: Dima Zavin <dima@android.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Imre Deak [Tue, 22 Sep 2009 23:47:00 +0000 (16:47 -0700)]
omapfb: HWA742: fix pointer to be const
Fixes the following:
warning: assignment discards qualifiers from pointer target type
Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Imre Deak [Tue, 22 Sep 2009 23:47:00 +0000 (16:47 -0700)]
omapfb: add FB manual update option to Kconfig
Also move the controller specific options up in the menu, to a more
logical spot.
Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arun c [Tue, 22 Sep 2009 23:46:59 +0000 (16:46 -0700)]
omapfb: fix coding style / remove dead line
- use __iomem type attribute where appropriate
- expand (a ? : b) to (a ? a : b)
As suggested by Russel King <linux@arm.linux.org.uk>
- remove a dead line from omapfb_main.c
Signed-off-by: Arun C <arunedarath@mistralsolutions.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
omapfb: suspend/resume only if FB device is already initialized
Check wether fbdev is NULL in suspend / resume functions. Fbdev is
NULL, if there is no lcd or it is not enabled in configuration.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, the only external (to dispc.c) IRQ handler was RFBI's frame
done handler. dispc's IRQ framework was very dumb: you could only have
one handler, and the semantics of {request,free}_irq were odd, to say the
least.
The new framework allows multiple consumers to register arbitrary IRQ
masks.
Signed-off-by: Daniel Stone <daniel.stone@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without wakeup enable omap doesn't wake up on dispc interrupts. This
causes problems in a case where mpu is in sleep state and dispc interrupt
fires.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
omapfb: dispc: disable iface clocks along with func clocks
Leaving interface clocks enabled causes dss pwrdm to stay in active state
when mpu is in active state. This fix puts dss to sleep state when it is
not needed.
Earlier version broke framebuffer on 24xx. This is fixed by enabling
clocks before trying to access DISPC_IRQSTATUS register.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Imre Deak [Tue, 22 Sep 2009 23:46:54 +0000 (16:46 -0700)]
omapfb: dispc: various typo fixes
- value and register offset was swapped in a dispc write
- DISPC_CONTROL register was used instead of DISPC_SYSCONFIG
- FIFO size bit field had incorrect length for OMAP3
Fixed-by: arun <arunedarath@mistralsolutions.com> Fixed-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com> Fixed-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Imre Deak [Tue, 22 Sep 2009 23:46:54 +0000 (16:46 -0700)]
N770: enable LCD MIPI-DCS in Kconfig
Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
omapfb: add support for rotation on the Blizzard LCD ctrl
The LCD controller (EPSON S1D13744) supports rotation (0, 90, 180 and 270
degrees) on hardware just setting the bits 0 and 1 of 0x28 register (LCD
Panel Configuration Register). Now it is possible to use this caps only
setting the angle degree on var rotate of fb_var_screeninfo using the
FBIOPUT_VSCREENINFO ioctl.
Fixed-by: Siarhei Siamashka <siarhei.siamashka@nokia.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@openbossa.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add glue to control the OMAP_LDP LCD as a frame buffer device using the
existing dispc.c driver under omapfb.
Patch updated for mainline kernel. Note that the drivers/video/omap
should be updated to pass omap_lcd_config in platform_data. The patch
should also be updated to compile if twl4030 is not selected, and
eventually to use the regulator framework.
Fixed-by: Jarkko Nikula <jarkko.nikula@gmail.com> Fixed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Stanley.Miao <stanley.miao@windriver.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steve Sakoman [Tue, 22 Sep 2009 23:46:51 +0000 (16:46 -0700)]
omapfb: add support for the Gumstix Overo LCD
Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
omapfb: add support for the OMAP3 Beagle DVI output
The default resolution is 1024x768@24bit
This version addresses the comments from Felipe Balbi adn Arun Edarath
Fixed-by: Felipe Contreras <felipe.contreras@gmail.com> Fixed-by: Steve Sakoman <steve@sakoman.com> Fixed-by: Jarkko Nikula <jarkko.nikula@gmail.com> Fixed-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Koen Kooi <koen@openembedded.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steve Sakoman [Tue, 22 Sep 2009 23:46:49 +0000 (16:46 -0700)]
omapfb: add support for the OMAP3 EVM LCD
Add LCD support for OMAP3 EVM
Backlight support by Arun C <arunedarath@mistralsolutions.com>
Fixed-by: Jarkko Nikula <jarkko.nikula@gmail.com> Fixed-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Steve Sakoman <steve@sakoman.com> Acked-by: Syed Mohammed Khasim <khasim@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kevin Hilman [Tue, 22 Sep 2009 23:46:48 +0000 (16:46 -0700)]
omapfb: add support for the 3430SDP LCD
The 3430SDP uses the same panel as the 2430SDP. The main difference are
in the GPIO lines used for panel enable and backlight, and the VAUX
register/commands sent to the TWL4030 power subsystem.
Also, some misc. whitespace cleanups.
Fixed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kevin Hilman <khilman@mvsita.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arun c [Tue, 22 Sep 2009 23:46:47 +0000 (16:46 -0700)]
omapfb: add support for the OMAP2EVM LCD
omap2evm LCD supports VGA and QVGA resolution, by default its in VGA mode.
Fixed-by: Jarkko Nikula <jarkko.nikula@gmail.com> Fixed-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Arun C <arunedarath@mistralsolutions.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add glue to control the 2430SDP LCD as a frame buffer device using the
existing dispc.c driver under omapfb.
Fixed-by: Kevin Hilman <khilman@mvista.com> Fixed-by: Sergio Aguirre <saaguirre@ti.com> Fixed-by: Francisco Alecrim <francisco.alecrim@indt.org.br> Fixed-by: Tony Lindgren <tony@atomide.com> Fixed-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Hunyue Yau <hyau@mvista.com> Signed-off-by: Kevin Hilman <khilman@mvista.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an updated version of the LCD driver for the Amstrad Delta to take
into account the recent changes to the omapfb infrastructure. The Delta
features a 480x320 12 bit DSTN panel.
Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Imre Deak [Tue, 22 Sep 2009 23:46:41 +0000 (16:46 -0700)]
omapfb: add support for MIPI-DCS compatible LCDs
Fixed-by: Mike Wege <ext-mike.wege@nokia.com> Fixed-by: Arnaud Patard <arnaud.patard@rtp-net.org> Fixed-by: Timo Savola <tsavola@movial.fi> Fixed-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Fixed-by: Trilok Soni <soni.trilok@gmail.com> Signed-off-by: Imre Deak <imre.deak@solidboot.com> Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kyungmin Park [Tue, 22 Sep 2009 23:46:40 +0000 (16:46 -0700)]
omapfb: add support for the Apollon LCD
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Glöckner [Tue, 22 Sep 2009 23:46:38 +0000 (16:46 -0700)]
gpiolib: allow poll() on value
Many gpio chips allow to generate interrupts when the value of a pin
changes. This patch gives usermode application the opportunity to make
use of this feature by calling poll(2) on the /sys/class/gpio/gpioN/value
sysfs file. The edge to trigger can be set in the edge file in the same
directory. Possible values are "none", "rising", "falling", and "both".
Using level triggers is not possible with current sysfs since nothing
changes the GPIO value (and the IRQ keeps triggering). Edge triggering
will "just work". Note that if there was an event between read() and
poll(), the poll() returns immediately.
Also note that this version only supports true GPIO interrupts. Some
later patch might be able to synthesize this behavior by timer-driven
polling; some systems seem to need that.
[dbrownell@users.sourceforge.net: align ids to 16 bit ids; whitespace] Signed-off-by: Daniel Glöckner <dg@emlix.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alek Du [Tue, 22 Sep 2009 23:46:36 +0000 (16:46 -0700)]
gpio: pca953x: add support for MAX7315
MAX7315 is pin and software compatible with PCA9534, so add it to the I2C
device ID table of pca953x driver.
http://www.datasheetcatalog.org/datasheet/maxim/MAX7315.pdf
Signed-off-by: Alek Du <alek.du@intel.com> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Langwell chip is the IO hub for Intel Moorestown platform which has a
64-pin gpio block device inside. It is exposed as a dedicated PCI device.
We use it to control outside peripheral as well as to do IRQ demuxing.
The gpio block uses MSI to send level type interrupt to IOAPIC.
Signed-off-by: Alek Du <alek.du@intel.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marek Vasut [Tue, 22 Sep 2009 23:46:35 +0000 (16:46 -0700)]
mfd/gpio: add a GPIO interface to the UCB1400 MFD chip driver via gpiolib
Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Brownell <david-b@pacbell.net> Cc: Samuel Ortiz <sameo@openedhand.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jani Nikula [Tue, 22 Sep 2009 23:46:33 +0000 (16:46 -0700)]
gpiolib: allow exported GPIO nodes to be named using sysfs links
Commit 926b663ce8215ba448960e1ff6e58b67a2c3b99b (gpiolib: allow GPIOs to
be named) already provides naming on the chip level. This patch provides
more flexibility by allowing multiple names where ever in sysfs on a per
GPIO basis.
Adapted from David Brownell's comments on a similar concept:
http://lkml.org/lkml/2009/4/20/203.
[randy.dunlap@oracle.com: fix build for CONFIG_GENERIC_GPIO=n] Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com> Acked-by: David Brownell <david-b@pacbell.net> Cc: Daniel Silverstone <dsilvers@simtec.co.uk> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Garrett [Tue, 22 Sep 2009 23:46:32 +0000 (16:46 -0700)]
rtc: add boot_timesource sysfs attribute
CONFIG_RTC_HCTOSYS allows the kernel to read the system time from the RTC
at boot and resume, avoiding the need for userspace to do so.
Unfortunately userspace currently has no way to know whether this
configuration option is enabled and thus cannot sensibly choose whether to
run hwclock itself or not. Add a hctosys sysfs attribute which indicates
whether a given RTC set the system clock.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Garrett [Tue, 22 Sep 2009 23:46:31 +0000 (16:46 -0700)]
rtc: document the sysfs interface
The sysfs interface to the RTC class drivers is currently undocumented.
Add some basic documentation defining the semantics of the fields.
Signed-off-by: Matthew Garrett <mjg@redhat.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Tue, 22 Sep 2009 23:46:31 +0000 (16:46 -0700)]
rtc: at91rm9200 fixes
Fix two new-ish runtime warnings in the at91rm9200 (etc) RTC:
Platform driver 'at91_rtc' needs updating - please use dev_pm_ops
... by just switching
IRQ 1/at91_rtc: IRQF_DISABLED is not guaranteed on shared IRQs
... no longer needed now that rtc_update_irq() changed
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Cc: Andrew Victor <linux@maxim.org.za> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Tue, 22 Sep 2009 23:46:29 +0000 (16:46 -0700)]
drivers/rtc: correct error-handling code
This code is not executed before ds1307->rtc has been successfully
initialized to the result of calling rtc_device_register. Thus the test
that ds1307->rtc is not NULL is always true.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
x = rtc_device_register(...)
... when != x = E
(
* if (x == NULL || ...) S1 else S2
|
* if (x == NULL && ...) S1 else S2
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Ribeiro [Tue, 22 Sep 2009 23:46:27 +0000 (16:46 -0700)]
rtc: driver for PCAP2 PMIC
[ospite@studenti.unina.it: get pcap data from the parent device] Signed-off-by: guiming zhuo <gmzhuo@gmail.com> Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver for the RTC COH 901 331 found in the ST-Ericsson U300
series mobile platforms to the RTC subsystem. It integrates to the ARM
kernel support recently added to RMKs ARM tree and will be enabled in the
U300 defconfig in due time.
Daniel Mack [Tue, 22 Sep 2009 23:46:23 +0000 (16:46 -0700)]
rtc: add driver for MXC's internal RTC module
This adds a driver for Freescale's MXC internal real time clock modules.
The code is taken from Freescale's BSPs, but modified to fit the current
kernel coding mechanisms. Also, the PMIC external clock function was
removed for now to not add dead bits and keep the code as simple as
possible.
[akpm@linux-foundation.org: make PIE_BIT_DEF[] static] Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Daniel Mack <daniel@caiaq.de> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Tue, 22 Sep 2009 23:46:18 +0000 (16:46 -0700)]
spi: handle TX-only/RX-only
Support two new half-duplex SPI implementation restrictions, for links
that talk to TX-only or RX-only devices. (Existing half-duplex flavors
support both transfer directions, just not at the same time.)
Move spi_async() into the spi.c core, and stop inlining it. Then make
that function perform error checks and reject messages that demand more
than the underlying controller can support.
Based on a patch from Marek Szyprowski which did this only for the
bitbanged GPIO driver.
Cc: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tAdd adds McSPI support for OMAP4430 SDP platform. All the base addresses
are changed between OMAP1/2/3 and OMAP4. The fields of the resource
structures are filled at runtime to have McSPI support on OMAP4.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tero Kristo [Tue, 22 Sep 2009 23:46:17 +0000 (16:46 -0700)]
spi: McSPI saves CHCONFx too
Previous restore was lazy and only restored CHxCONF when it was needed by
a specific chip select. This could cause occasional errors on an SPI bus
where multiple chip selects are in use.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hemanth V [Tue, 22 Sep 2009 23:46:16 +0000 (16:46 -0700)]
spi: McSPI off-mode support
Add context save/restore feature to McSPI driver.
Signed-off-by: Hemanth V <hemanthv@ti.com> Reviewed-by: Aaro Koskinen <Aaro.Koskinen@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 22 Sep 2009 23:46:14 +0000 (16:46 -0700)]
spi_s3c24xx: cache device setup data
With the update to the spi_bitbang driver, the transfer setup code is
being called more often, and thus is often re-doing calculations that have
been done before. The SPI layer allows our driver to add its own data to
each device so add a result cache to each device.
This should also remove the problem where we where directly setting up
registers in the setup call which meant we might overwrite the state of an
extant transfer.,
Signed-off-by: Ben Dooks <ben@simtec.co.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 22 Sep 2009 23:46:12 +0000 (16:46 -0700)]
spi_s3c24xx: fix header includes
The driver includes <asm/io.h> where it should be including <linux/io.h>
and also includes <mach/hardware.h> and <asm/dma.h> without using anything
from these.
Signed-off-by: Ben Dooks <ben@simtec.co.uk> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Antonio Ospite [Tue, 22 Sep 2009 23:46:10 +0000 (16:46 -0700)]
pxa2xx_spi: register earlier
Register pxa2xx_spi earlier so it can be used with cpufreq
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Daniel Ribeiro <drwyrm@gmail.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Tue, 22 Sep 2009 23:46:08 +0000 (16:46 -0700)]
spi: prefix modalias with "spi:"
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Jean Delvare <khali@linux-fr.org> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Dmitry Torokhov <dtor@mail.ru> Cc: Samuel Ortiz <sameo@openedhand.com> Cc: "John W. Linville" <linville@tuxdriver.com> Acked-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Tue, 22 Sep 2009 23:46:07 +0000 (16:46 -0700)]
hwmon: lm70: convert to device table matching
Make the code a little bit nicer, and shorter.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kaiwan N Billimoria <kaiwan@designergraphix.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Jean Delvare <khali@linux-fr.org> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Tue, 22 Sep 2009 23:46:05 +0000 (16:46 -0700)]
hwmon: adxx: convert to device table matching
Make the code a little bit nicer, and shorter.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Marc Pignat <marc.pignat@hevs.ch> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Jean Delvare <khali@linux-fr.org> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Marc Pignat <marc.pignat@hevs.ch> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Tue, 22 Sep 2009 23:46:04 +0000 (16:46 -0700)]
of: remove "stm,m25p40" alias
The alias isn't needed any longer since the m25p80 driver converted to the
module device table matching.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Jean Delvare <khali@linux-fr.org> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Tue, 22 Sep 2009 23:46:04 +0000 (16:46 -0700)]
spi: add support for device table matching
With this patch spi drivers can use standard spi_driver.id_table and
MODULE_DEVICE_TABLE() mechanisms to bind against the devices. Just like
we do with I2C drivers.
This is useful when a single driver supports several variants of devices
but it is not possible to detect them in run-time (like non-JEDEC chips
probing in drivers/mtd/devices/m25p80.c), and when platform_data usage is
overkill.
This patch also makes life a lot easier on OpenFirmware platforms, since
with OF we extensively use proper device IDs in modaliases.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Jean Delvare <khali@linux-fr.org> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spi: add default selection of PL022 for ARM reference platforms
This makes the PL022 driver a default choice for any RealView and
Versatile boards plus the integrator IMPD1 which all contain the PL022
PrimeCell. This will make it a default choice if and only if a user
selects SPI support for their board.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Tue, 22 Sep 2009 23:46:00 +0000 (16:46 -0700)]
spi.h: add missing kernel-doc for struct spi_master
Add missing kernel-doc notation in spi.h for struct spi_master:
Warning(include/linux/spi/spi.h:289): No description found for parameter 'mode_bits'
Warning(include/linux/spi/spi.h:289): No description found for parameter 'flags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steven A. Falco [Tue, 22 Sep 2009 23:45:58 +0000 (16:45 -0700)]
spi: add spi_ppc4xx driver
This adds a SPI driver for the SPI controller found in the IBM/AMCC
4xx PowerPC's.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Wolfgang Ocker <weo@reccoware.de> Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Steven A. Falco <sfalco@harris.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function uses signed integers for the unix_date and local variables -
if a negative number is supplied and the leap-year condition is not met,
month will be 0, leading to a later read of day_n[-1]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Petr Vandrovec <VANDROVE@vc.cvut.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/proc/kcore: update stat.st_size after memory hotplug
After memory hotplug (or other events in future), kcore size can be
modified.
To update inode->i_size, we have to know inode/dentry but we can't get it
from inside /proc directly. But considerinyg memory hotplug, kcore image
is updated only when it's opened. Then, updating inode->i_size at open()
is enough.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently the size of /proc/kcore which can be read by 'ls -l' is 0. But
it's not the correct value.
On x86-64, ls -l shows
... root root 140737486266368 2009-09-17 10:29 /proc/kcore
Then, 7FFFFFFE02000. This comes from vmalloc area's size.
(*) This shows "core" size, not memory size.
This patch shows the size by updating "size" field in struct
proc_dir_entry. Later, lookup routine will create inode and fill
inode->i_size based on this value. Then, this has a problem.
- Once inode is cached, inode->i_size will never be updated.
Then, this patch is not memory-hotplug-aware.
To update inode->i_size, we have to know dentry or inode.
But there is no way to lookup them by inside kernel. Hmmm....
Next patch will try it.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some archs define MODULED_VADDR/MODULES_END which is not in VMALLOC area.
This is handled only in x86-64. This patch make it more generic. And we
can use vread/vwrite to access the area. Fix it.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Jiri Slaby <jirislaby@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Benjamin Herrenschmidt <benh@kernel.crashing.org> pointed out that vmemmap
range is not included in KCORE_RAM, KCORE_VMALLOC ....
This adds KCORE_VMEMMAP if SPARSEMEM_VMEMMAP is used. By this, vmemmap
can be readable via /proc/kcore
Because it's not vmalloc area, vread/vwrite cannot be used. But the range
is static against the memory layout, this patch handles vmemmap area by
the same scheme with physical memory.
This patch assumes SPARSEMEM_VMEMMAP range is not in VMALLOC range. It's
correct now.
[akpm@linux-foundation.org: fix typo] Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Jiri Slaby <jirislaby@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: WANG Cong <xiyou.wangcong@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For /proc/kcore, each arch registers its memory range by kclist_add().
In usual,
- range of physical memory
- range of vmalloc area
- text, etc...
are registered but "range of physical memory" has some troubles. It
doesn't updated at memory hotplug and it tend to include unnecessary
memory holes. Now, /proc/iomem (kernel/resource.c) includes required
physical memory range information and it's properly updated at memory
hotplug. Then, it's good to avoid using its own code(duplicating
information) and to rebuild kclist for physical memory based on
/proc/iomem.
Originally, walk_memory_resource() was introduced to traverse all memory
of "System RAM" for detecting memory hotplug/unplug range. For doing so,
flags of IORESOUCE_MEM|IORESOURCE_BUSY was used and this was enough for
memory hotplug.
But for using other purpose, /proc/kcore, this may includes some firmware
area marked as IORESOURCE_BUSY | IORESOUCE_MEM. This patch makes the
check strict to find out busy "System RAM".
Note: PPC64 keeps their own walk_memory_resouce(), which walk through
ppc64's lmb informaton. Because old kclist_add() is called per lmb, this
patch makes no difference in behavior, finally.
And this patch removes CONFIG_MEMORY_HOTPLUG check from this function.
Because pfn_valid() just show "there is memmap or not* and cannot be used
for "there is physical memory or not", this function is useful in generic
to scan physical memory range.
Some 64bit arch has special segment for mapping kernel text. It should be
entried to /proc/kcore in addtion to direct-linear-map, vmalloc area.
This patch unifies KCORE_TEXT entry scattered under x86 and ia64.
I'm not familiar with other archs (mips has its own even after this patch)
but range of [_stext ..._end) is a valid area of text and it's not in
direct-map area, defining CONFIG_ARCH_PROC_KCORE_TEXT is only a necessary
thing to do.
Note: I left mips as it is now.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For /proc/kcore, vmalloc areas are registered per arch. But, all of them
registers same range of [VMALLOC_START...VMALLOC_END) This patch unifies
them. By this. archs which have no kclist_add() hooks can see vmalloc
area correctly.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently, kclist_add() only eats start address and size as its arguments.
Considering to make kclist dynamically reconfigulable, it's necessary to
know which kclists are for System RAM and which are not.
This patch add kclist types as
KCORE_RAM
KCORE_VMALLOC
KCORE_TEXT
KCORE_OTHER
This "type" is used in a patch following this for detecting KCORE_RAM.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: WANG Cong <xiyou.wangcong@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>