Linus Torvalds [Wed, 10 Jun 2009 23:20:30 +0000 (16:20 -0700)]
Merge branch 'percpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'percpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
percpu: remove rbtree and use page->index instead
percpu: don't put the first chunk in reverse-map rbtree
Linus Torvalds [Wed, 10 Jun 2009 23:19:14 +0000 (16:19 -0700)]
Merge branch 'iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (61 commits)
amd-iommu: remove unnecessary "AMD IOMMU: " prefix
amd-iommu: detach device explicitly before attaching it to a new domain
amd-iommu: remove BUS_NOTIFY_BOUND_DRIVER handling
dma-debug: simplify logic in driver_filter()
dma-debug: disable/enable irqs only once in device_dma_allocations
dma-debug: use pr_* instead of printk(KERN_* ...)
dma-debug: code style fixes
dma-debug: comment style fixes
dma-debug: change hash_bucket_find from first-fit to best-fit
x86: enable GART-IOMMU only after setting up protection methods
amd_iommu: fix lock imbalance
dma-debug: add documentation for the driver filter
dma-debug: add dma_debug_driver kernel command line
dma-debug: add debugfs file for driver filter
dma-debug: add variables and checks for driver filter
dma-debug: fix debug_dma_sync_sg_for_cpu and debug_dma_sync_sg_for_device
dma-debug: use sg_dma_len accessor
dma-debug: use sg_dma_address accessor instead of using dma_address directly
amd-iommu: don't free dma adresses below 512MB with CONFIG_IOMMU_STRESS
amd-iommu: don't preallocate page tables with CONFIG_IOMMU_STRESS
...
Linus Torvalds [Wed, 10 Jun 2009 23:16:48 +0000 (16:16 -0700)]
Merge branch 'futexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'futexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: fix restart in wait_requeue_pi
futex: fix restart for early wakeup in futex_wait_requeue_pi()
futex: cleanup error exit
futex: remove the wait queue
futex: add requeue-pi documentation
futex: remove FUTEX_REQUEUE_PI (non CMP)
futex: fix futex_wait_setup key handling
sparc64: extend TI_RESTART_BLOCK space by 8 bytes
futex: fixup unlocked requeue pi case
futex: add requeue_pi functionality
futex: split out futex value validation code
futex: distangle futex_requeue()
futex: add FUTEX_HAS_TIMEOUT flag to restart.futex.flags
rt_mutex: add proxy lock routines
futex: split out fixup owner logic from futex_lock_pi()
futex: split out atomic logic from futex_lock_pi()
futex: add helper to find the top prio waiter of a futex
futex: separate futex_wait_queue_me() logic from futex_wait()
Linus Torvalds [Wed, 10 Jun 2009 23:16:27 +0000 (16:16 -0700)]
Merge branch 'x86-xen-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-xen-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (42 commits)
xen: cache cr0 value to avoid trap'n'emulate for read_cr0
xen/x86-64: clean up warnings about IST-using traps
xen/x86-64: fix breakpoints and hardware watchpoints
xen: reserve Xen start_info rather than e820 reserving
xen: add FIX_TEXT_POKE to fixmap
lguest: update lazy mmu changes to match lguest's use of kvm hypercalls
xen: honour VCPU availability on boot
xen: add "capabilities" file
xen: drop kexec bits from /sys/hypervisor since kexec isn't implemented yet
xen/sys/hypervisor: change writable_pt to features
xen: add /sys/hypervisor support
xen/xenbus: export xenbus_dev_changed
xen: use device model for suspending xenbus devices
xen: remove suspend_cancel hook
xen/dev-evtchn: clean up locking in evtchn
xen: export ioctl headers to userspace
xen: add /dev/xen/evtchn driver
xen: add irq_from_evtchn
xen: clean up gate trap/interrupt constants
xen: set _PAGE_NX in __supported_pte_mask before pagetable construction
...
Linus Torvalds [Wed, 10 Jun 2009 23:15:14 +0000 (16:15 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Clear TS in irq_ts_save() when in an atomic section
x86: Detect use of extended APIC ID for AMD CPUs
x86: memtest: remove 64-bit division
x86, UV: Fix macros for multiple coherency domains
x86: Fix non-lazy GS handling in sys_vm86()
x86: Add quirk for reboot stalls on a Dell Optiplex 360
x86: Fix UV BAU activation descriptor init
Linus Torvalds [Wed, 10 Jun 2009 23:13:20 +0000 (16:13 -0700)]
Merge branch 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (22 commits)
x86: fix system without memory on node0
x86, mm: Fix node_possible_map logic
mm, x86: remove MEMORY_HOTPLUG_RESERVE related code
x86: make sparse mem work in non-NUMA mode
x86: process.c, remove useless headers
x86: merge process.c a bit
x86: use sparse_memory_present_with_active_regions() on UMA
x86: unify 64-bit UMA and NUMA paging_init()
x86: Allow 1MB of slack between the e820 map and SRAT, not 4GB
x86: Sanity check the e820 against the SRAT table using e820 map only
x86: clean up and and print out initial max_pfn_mapped
x86/pci: remove rounding quirk from e820_setup_gap()
x86, e820, pci: reserve extra free space near end of RAM
x86: fix typo in address space documentation
x86: 46 bit physical address support on 64 bits
x86, mm: fault.c, use printk_once() in is_errata93()
x86: move per-cpu mmu_gathers to mm/init.c
x86: move max_pfn_mapped and max_low_pfn_mapped to setup.c
x86: unify noexec handling
x86: remove (null) in /sys kernel_page_tables
...
Linus Torvalds [Wed, 10 Jun 2009 23:13:06 +0000 (16:13 -0700)]
Merge branch 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, microcode: Simplify vfree() use
x86: microcode: use smp_call_function_single instead of set_cpus_allowed, cleanup of synchronization logic
Linus Torvalds [Wed, 10 Jun 2009 22:51:15 +0000 (15:51 -0700)]
Merge branch 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: cpu_debug: Remove model information to reduce encoding-decoding
x86: fixup numa_node information for AMD CPU northbridge functions
x86: k8 convert node_to_k8_nb_misc() from a macro to an inline function
x86: cacheinfo: complete L2/L3 Cache and TLB associativity field definitions
x86/docs: add description for cache_disable sysfs interface
x86: cacheinfo: disable L3 ECC scrubbing when L3 cache index is disabled
x86: cacheinfo: replace sysfs interface for cache_disable feature
x86: cacheinfo: use cached K8 NB_MISC devices instead of scanning for it
x86: cacheinfo: correct return value when cache_disable feature is not active
x86: cacheinfo: use L3 cache index disable feature only for CPUs that support it
Linus Torvalds [Wed, 10 Jun 2009 22:49:36 +0000 (15:49 -0700)]
Merge branch 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, nmi: Use predefined numbers instead of hardcoded one
x86: asm/processor.h: remove double declaration
x86, mtrr: replace MTRRdefType_MSR with msr-index's MSR_MTRRdefType
x86, mtrr: replace MTRRfix4K_C0000_MSR with msr-index's MSR_MTRRfix4K_C0000
x86, mtrr: remove mtrr MSRs double declaration
x86, mtrr: replace MTRRfix16K_80000_MSR with msr-index's MSR_MTRRfix16K_80000
x86, mtrr: replace MTRRfix64K_00000_MSR with msr-index's MSR_MTRRfix64K_00000
x86, mtrr: replace MTRRcap_MSR with msr-index's MSR_MTRRcap
x86: mce: remove duplicated #include
x86: msr-index.h remove duplicate MSR C001_0015 declaration
x86: clean up arch/x86/kernel/tsc_sync.c a bit
x86: use symbolic name for VM86_SIGNAL when used as vm86 default return
x86: added 'ifndef _ASM_X86_IOMAP_H' to iomap.h
x86: avoid multiple declaration of kstack_depth_to_print
x86: vdso/vma.c declare vdso_enabled and arch_setup_additional_pages before they get used
x86: clean up declarations and variables
x86: apic/x2apic_cluster.c x86_cpu_to_logical_apicid should be static
x86 early quirks: eliminate unused function
Linus Torvalds [Wed, 10 Jun 2009 22:49:10 +0000 (15:49 -0700)]
Merge branch 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, 64-bit: ifdef out struct thread_struct::ip
x86, 32-bit: ifdef out struct thread_struct::fs
x86: clean up alternative.h
Linus Torvalds [Wed, 10 Jun 2009 22:32:59 +0000 (15:32 -0700)]
Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix typo in sched-rt-group.txt file
ftrace: fix typo about map of kernel priority in ftrace.txt file.
sched: properly define the sched_group::cpumask and sched_domain::span fields
sched, timers: cleanup avenrun users
sched, timers: move calc_load() to scheduler
sched: Don't export sched_mc_power_savings on multi-socket single core system
sched: emit thread info flags with stack trace
sched: rt: document the risk of small values in the bandwidth settings
sched: Replace first_cpu() with cpumask_first() in ILB nomination code
sched: remove extra call overhead for schedule()
sched: use group_first_cpu() instead of cpumask_first(sched_group_cpus())
wait: don't use __wake_up_common()
sched: Nominate a power-efficient ilb in select_nohz_balancer()
sched: Nominate idle load balancer from a semi-idle package.
sched: remove redundant hierarchy walk in check_preempt_wakeup
Linus Torvalds [Wed, 10 Jun 2009 22:30:41 +0000 (15:30 -0700)]
Merge branch 'x86-kbuild-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-kbuild-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (46 commits)
x86, boot: add new generated files to the appropriate .gitignore files
x86, boot: correct the calculation of ZO_INIT_SIZE
x86-64: align __PHYSICAL_START, remove __KERNEL_ALIGN
x86, boot: correct sanity checks in boot/compressed/misc.c
x86: add extension fields for bootloader type and version
x86, defconfig: update kernel position parameters
x86, defconfig: update to current, no material changes
x86: make CONFIG_RELOCATABLE the default
x86: default CONFIG_PHYSICAL_START and CONFIG_PHYSICAL_ALIGN to 16 MB
x86: document new bzImage fields
x86, boot: make kernel_alignment adjustable; new bzImage fields
x86, boot: remove dead code from boot/compressed/head_*.S
x86, boot: use LOAD_PHYSICAL_ADDR on 64 bits
x86, boot: make symbols from the main vmlinux available
x86, boot: determine compressed code offset at compile time
x86, boot: use appropriate rep string for move and clear
x86, boot: zero EFLAGS on 32 bits
x86, boot: set up the decompression stack as early as possible
x86, boot: straighten out ranges to copy/zero in compressed/head*.S
x86, boot: stylistic cleanups for boot/compressed/head_64.S
...
Fixed trivial conflict in arch/x86/configs/x86_64_defconfig manually
Linus Torvalds [Wed, 10 Jun 2009 22:25:41 +0000 (15:25 -0700)]
Merge branch 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (76 commits)
x86, apic: Fix dummy apic read operation together with broken MP handling
x86, apic: Restore irqs on fail paths
x86: Print real IOAPIC version for x86-64
x86: enable_update_mptable should be a macro
sparseirq: Allow early irq_desc allocation
x86, io-apic: Don't mark pin_programmed early
x86, irq: don't call mp_config_acpi_gsi() if update_mptable is not enabled
x86, irq: update_mptable needs pci_routeirq
x86: don't call read_apic_id if !cpu_has_apic
x86, apic: introduce io_apic_irq_attr
x86/pci: add 4 more return parameters to IO_APIC_get_PCI_irq_vector(), fix
x86: read apic ID in the !acpi_lapic case
x86: apic: Fixmap apic address even if apic disabled
x86: display extended apic registers with print_local_APIC and cpu_debug code
x86: read apic ID in the !acpi_lapic case
x86: clean up and fix setup_clear/force_cpu_cap handling
x86: apic: Check rev 3 fadt correctly for physical_apic bit
x86/pci: update pirq_enable_irq() to setup io apic routing
x86/acpi: move setup io apic routing out of CONFIG_ACPI scope
x86/pci: add 4 more return parameters to IO_APIC_get_PCI_irq_vector()
...
Harald Welte [Mon, 8 Jun 2009 10:27:54 +0000 (18:27 +0800)]
CPUFREQ: Enable acpi-cpufreq driver for VIA/Centaur CPUs
The VIA/Centaur C7, C7-M and Nano CPU's all support ACPI based cpu p-states
using a MSR interface. The Linux driver just never made use of it, since in
addition to the check for the EST flag it also checked if the vendor is Intel.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
[ Removed the vendor checks entirely - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 10 Jun 2009 03:40:25 +0000 (20:40 -0700)]
Make /dev/zero reads interruptible by signals
This helps with bad latencies for large reads from /dev/zero, but might
conceivably break some application that "knows" that a read of /dev/zero
cannot return early. So do this early in the merge window to give us
maximal test coverage, even if the patch is totally trivial.
Obviously, no well-behaved application should ever depend on the read
being uninterruptible, but hey, bugs happen.
Peter Botha [Wed, 10 Jun 2009 00:16:32 +0000 (17:16 -0700)]
char: mxser, fix ISA board lookup
There's a bug in the mxser kernel module that still appears in the
2.6.29.4 kernel.
mxser_get_ISA_conf takes a ioaddress as its first argument, by passing the
not of the ioaddr, you're effectively passing 0 which means it won't be
able to talk to an ISA card. I have tested this, and removing the !
fixes the problem.
Jan Kara [Tue, 9 Jun 2009 23:26:26 +0000 (16:26 -0700)]
jbd: fix race in buffer processing in commit code
In commit code, we scan buffers attached to a transaction. During this
scan, we sometimes have to drop j_list_lock and then we recheck whether
the journal buffer head didn't get freed by journal_try_to_free_buffers().
But checking for buffer_jbd(bh) isn't enough because a new journal head
could get attached to our buffer head. So add a check whether the journal
head remained the same and whether it's still at the same transaction and
list.
This is a nasty bug and can cause problems like memory corruption (use after
free) or trigger various assertions in JBD code (observed).
Signed-off-by: Jan Kara <jack@suse.cz> Cc: <stable@kernel.org> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ian Kent [Tue, 9 Jun 2009 23:26:24 +0000 (16:26 -0700)]
autofs4: remove hashed check in validate_wait()
The recent ->lookup() deadlock correction required the directory inode
mutex to be dropped while waiting for expire completion. We were
concerned about side effects from this change and one has been identified.
I saw several error messages.
They cause autofs to become quite confused and don't really point to the
actual problem.
Things like:
handle_packet_missing_direct:1376: can't find map entry for (43,1827932)
which is usually totally fatal (although in this case it wouldn't be
except that I treat is as such because it normally is).
do_mount_direct: direct trigger not valid or already mounted
/test/nested/g3c/s1/ss1
which is recoverable, however if this problem is at play it can cause
autofs to become quite confused as to the dependencies in the mount tree
because mount triggers end up mounted multiple times. It's hard to
accurately check for this over mounting case and automount shouldn't need
to if the kernel module is doing its job.
There was one other message, similar in consequence of this last one but I
can't locate a log example just now.
When checking if a mount has already completed prior to adding a new mount
request to the wait queue we check if the dentry is hashed and, if so, if
it is a mount point. But, if a mount successfully completed while we
slept on the wait queue mutex the dentry must exist for the mount to have
completed so the test is not really needed.
Mounts can also be done on top of a global root dentry, so for the above
case, where a mount request completes and the wait queue entry has already
been removed, the hashed test returning false can cause an incorrect
callback to the daemon. Also, d_mountpoint() is not sufficient to check
if a mount has completed for the multi-mount case when we don't have a
real mount at the base of the tree.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Tue, 9 Jun 2009 23:26:23 +0000 (16:26 -0700)]
shm: fix unused warnings on nommu
The massive nommu update (8feae131) resulted in these warnings:
ipc/shm.c: In function `sys_shmdt':
ipc/shm.c:974: warning: unused variable `size'
ipc/shm.c:972: warning: unused variable `next'
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
cls_cgroup: Fix oops when user send improperly 'tc filter add' request
r8169: fix crash when large packets are received
Linus Torvalds [Tue, 9 Jun 2009 15:41:22 +0000 (08:41 -0700)]
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md/raid5: fix bug in reshape code when chunk_size decreases.
md/raid5 - avoid deadlocks in get_active_stripe during reshape
md/raid5: use conf->raid_disks in preference to mddev->raid_disk
Chuck Ebbert [Tue, 9 Jun 2009 14:40:50 +0000 (10:40 -0400)]
x86: Clear TS in irq_ts_save() when in an atomic section
The dynamic FPU context allocation changes caused the padlock driver
to generate the below warning. Fix it by masking TS when doing padlock
encryption operations in an atomic section.
Booting a 32-bit kernel on Magny-Cours results in the following panic:
...
Using APIC driver default
...
Overriding APIC driver with bigsmp
...
Getting VERSION: 80050010
Getting VERSION: 80050010
Getting ID: 10000000
Getting ID: ef000000
Getting LVT0: 700
Getting LVT1: 10000
Kernel panic - not syncing: Boot APIC ID in local APIC unexpected (16 vs 0)
Pid: 1, comm: swapper Not tainted 2.6.30-rcX #2
Call Trace:
[<c05194da>] ? panic+0x38/0xd3
[<c0743102>] ? native_smp_prepare_cpus+0x259/0x31f
[<c073b19d>] ? kernel_init+0x3e/0x141
[<c073b15f>] ? kernel_init+0x0/0x141
[<c020325f>] ? kernel_thread_helper+0x7/0x10
The reason is that default_get_apic_id handled extension of local APIC
ID field just in case of XAPIC.
Thus for this AMD CPU, default_get_apic_id() returns 0 and
bigsmp_get_apic_id() returns 16 which leads to the respective kernel
panic.
This patch introduces a Linux specific feature flag to indicate
support for extended APIC id (8 bits instead of 4 bits width) and sets
the flag on AMD CPUs if applicable.
it turns out that we need clear cpus_hardware_enabled in that case.
Reported-and-tested-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Minoru Usui [Tue, 9 Jun 2009 11:03:09 +0000 (04:03 -0700)]
cls_cgroup: Fix oops when user send improperly 'tc filter add' request
I found a bug in cls_cgroup_change() in cls_cgroup.c.
cls_cgroup_change() expected tca[TCA_OPTIONS] was set from user space properly,
but tc in iproute2-2.6.29-1 (which I used) didn't set it.
In the current source code of tc in git, it set tca[TCA_OPTIONS].
If we always use a newest iproute2 in git when we use cls_cgroup,
we don't face this oops probably.
But I think, kernel shouldn't panic regardless of use program's behaviour.
Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 9 Jun 2009 11:01:02 +0000 (04:01 -0700)]
r8169: fix crash when large packets are received
Michael Tokarev reported receiving a large packet could crash
a machine with RTL8169 NIC.
( original thread at http://lkml.org/lkml/2009/6/8/192 )
Problem is this driver tells that NIC frames up to 16383 bytes
can be received but provides skb to rx ring allocated with
smaller sizes (1536 bytes in case standard 1500 bytes MTU is used)
When a frame larger than what was allocated by driver is received,
dma transfert can occurs past the end of buffer and corrupt
kernel memory.
Fix is to tell to NIC what is the maximum size a frame can be.
This bug is very old, (before git introduction, linux-2.6.10), and
should be backported to stable versions.
Reported-by: Michael Tokarev <mjt@tls.msk.ru> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Tested-by: Michael Tokarev <mjt@tls.msk.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Handling this event causes device assignment in KVM to fail because the
device gets re-attached as soon as the pci-stub registers as the driver
for the device.
NeilBrown [Tue, 9 Jun 2009 06:32:22 +0000 (16:32 +1000)]
md/raid5: fix bug in reshape code when chunk_size decreases.
Now that we support changing the chunksize, we calculate
"reshape_sectors" to be the max of number of sectors in old
and new chunk size.
However there is one please where we still use 'chunksize'
rather than 'reshape_sectors'.
This causes a reshape that reduces the size of chunks to freeze.
NeilBrown [Tue, 9 Jun 2009 04:39:59 +0000 (14:39 +1000)]
md/raid5 - avoid deadlocks in get_active_stripe during reshape
md has functionality to 'quiesce' and array so that all pending
IO completed and no new IO starts. This is used to achieve a
stable state before making internal changes.
Currently this quiescing applies equally to normal IO, resync
IO, and reshape IO.
However there is a problem with applying it to reshape IO.
Reshape can have multiple 'stripe_heads' that must be active together.
If the quiesce come between allocating the first and the last of
such a collection, then we deadlock, as the last will not be allocated
until the quiesce is lifted, the quiesce will not be lifted until the
first (which has been allocated) gets used, and that first cannot be
used until the last is allocated.
It is not necessary to inhibit reshape IO when a quiesce is
requested. Those places in the code that require a full quiesce will
ensure the reshape thread is not running at all.
So allow reshape requests to get access to new stripe_heads without
being blocked by a 'quiesce'.
This only affects in-place reshapes (i.e. where the array does not
grow or shrink) and these are only newly supported. So this patch is
not needed in earlier kernels.
Linus Torvalds [Mon, 8 Jun 2009 19:31:53 +0000 (12:31 -0700)]
async: Fix lack of boot-time console due to insufficient synchronization
Our async work synchronization was broken by "async: make sure
independent async domains can't accidentally entangle" (commit d5a877e8dd409d8c702986d06485c374b705d340), because it would report
the wrong lowest active async ID when there was both running and
pending async work.
This caused things like no being able to read the root filesystem,
resulting in missing console devices and inability to run 'init',
causing a boot-time panic.
This fixes it by properly returning the lowest pending async ID: if
there is any running async work, that will have a lower ID than any
pending work, and we should _not_ look at the pending work list.
There were alternative patches from Jaswinder and James, but this one
also cleans up the code by removing the pointless 'ret' variable and
the unnecesary testing for an empty list around 'for_each_entry()' (if
the list is empty, the for_each_entry() thing just won't execute).
Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=13474 Reported-and-tested-by: Chris Clayton <chris2553@googlemail.com> Cc: Jaswinder Singh Rajput <jaswinder@kernel.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using gcc 3.3.5 a "make allmodconfig" + "CONFIG_KVM=n"
triggers a build error:
arch/x86/mm/built-in.o(.init.text+0x43f7): In function `__change_page_attr':
arch/x86/mm/pageattr.c:114: undefined reference to `__udivdi3'
make: *** [.tmp_vmlinux1] Error 1
The culprit turned out to be a division in arch/x86/mm/memtest.c
For more info see this thread:
Jack Steiner [Mon, 8 Jun 2009 15:44:05 +0000 (10:44 -0500)]
x86, UV: Fix macros for multiple coherency domains
Fix bug in the SGI UV macros that support systems with multiple
coherency domains. The macros used for referencing global MMR
(chipset registers) are failing to correctly "or" the NASID
(node identifier) bits that reside above M+N. These high bits
are supplied automatically by the chipset for memory accesses
coming from the processor socket.
However, the bits must be present for references to the special
global MMR space used to map chipset registers. (See uv_hub.h
for more details ...)
The bug results in references to invalid/incorrect nodes.
Linus Torvalds [Mon, 8 Jun 2009 16:22:53 +0000 (09:22 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Outline udelay and fix a few issues.
MIPS: ioctl.h: Fix headers_check warnings
MIPS: Cobalt: PCI bus is always required to obtain the board ID
MIPS: Kconfig: Remove "Support for" from Cavium system type
MIPS: Sibyte: Honor CONFIG_CMDLINE
SSB: BCM47xx: Export ssb_watchdog_timer_set
Ralf Baechle [Sat, 28 Feb 2009 09:44:28 +0000 (09:44 +0000)]
MIPS: Outline udelay and fix a few issues.
Outlining fixes the issue were on certain CPUs such as the R10000 family
the delay loop would need an extra cycle if it overlaps a cacheline
boundary.
The rewrite also fixes build errors with GCC 4.4 which was changed in
way incompatible with the kernel's inline assembly.
Relying on pure C for computation of the delay value removes the need for
explicit. The price we pay is a slight slowdown of the computation - to
be fixed on another day.
Linus Torvalds [Mon, 8 Jun 2009 15:29:31 +0000 (08:29 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5543/1: arm: serial amba: add missing declaration in serial.h
[ARM] pxa: fix pxa27x_udc default pullup GPIO
[ARM] pxa/imote2: fix UCAM sensor board ADC model number
mx[23]: don't put clock lookups in __initdata
fix oops when using console=ttymxcN with N > 0
[ARM] ARMv7 errata: only apply fixes when running on applicable CPU
[ARM] 5534/1: kmalloc must return a cache line aligned buffer
Linus Torvalds [Mon, 8 Jun 2009 14:53:59 +0000 (07:53 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci-of: Fix the wrong accessor to HOSTVER register
mvsdio: fix config failure with some high speed SDHC cards
mvsdio: ignore high speed timing requests from the core
mmc/omap: Use disable_irq_nosync() from within irq handlers.
sdhci-of: Add fsl,esdhc as a valid compatible to bind against
mvsdio: allow automatic loading when modular
mxcmmc: Fix missing return value checking in DMA setup code.
mxcmmc : Reset the SDHC hardware if software timeout occurs.
omap_hsmmc: Trivial fix for a typo in comment
mxcmmc: decrease minimum frequency to make MMC cards work
Joerg Roedel [Mon, 8 Jun 2009 13:53:46 +0000 (15:53 +0200)]
dma-debug: simplify logic in driver_filter()
This patch makes the driver_filter function more readable by
reorganizing the code. The removal of a code code block to an upper
indentation level makes hard-to-read line-wraps unnecessary.
Joerg Roedel [Mon, 8 Jun 2009 13:39:24 +0000 (15:39 +0200)]
dma-debug: use pr_* instead of printk(KERN_* ...)
The pr_* macros are shorter than the old printk(KERN_ ...) variant.
Change the dma-debug code to use the new macros and save a few
unnecessary line breaks. If lines don't break the source code can also
be grepped more easily.
Avi Kivity [Sat, 6 Jun 2009 09:34:39 +0000 (12:34 +0300)]
KVM: Explicity initialize cpus_hardware_enabled
Under CONFIG_MAXSMP, cpus_hardware_enabled is allocated from the heap and
not statically initialized. This causes a crash on reboot when kvm thinks
vmx is enabled on random nonexistent cpus and accesses nonexistent percpu
lists.
Fix by explicitly clearing the variable.
Cc: stable@kernel.org Reported-and-tested-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Avi Kivity <avi@redhat.com>
[ARM] 5543/1: arm: serial amba: add missing declaration in serial.h
This header is sometimes included in the uncompress stage to get
register values, but no <linux/amba/bus.h> can be included there.
So declare "struct amba_device" here before using it in a prototype.
Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Lubomir Rintel [Sun, 7 Jun 2009 14:23:48 +0000 (16:23 +0200)]
x86: Fix non-lazy GS handling in sys_vm86()
This fixes a stack corruption panic or null dereference oops
due to a bad GS in resume_userspace() when returning from
sys_vm86() and calling lockdep_sys_exit().
Only a problem when CONFIG_LOCKDEP and CONFIG_CC_STACKPROTECTOR
enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Cc: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <1244384628.2323.4.camel@bimbo> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cyrill Gorcunov [Sun, 7 Jun 2009 12:48:40 +0000 (16:48 +0400)]
x86, apic: Fix dummy apic read operation together with broken MP handling
Ingo Molnar reported that read_apic is buggy novadays:
[ 0.000000] Using APIC driver default
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] APIC: disable apic facility
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: at arch/x86/kernel/apic/apic.c:254 native_apic_read_dummy+0x2d/0x3b()
[ 0.000000] Hardware name: HP OmniBook PC
Indeed we still rely on apic->read operation for SMP compiled
kernel. And instead of disfigure the SMP code with #ifdef we
allow to call apic->read. To capture any unexpected results
we check for apic->read being called for sane reason via
WARN_ON_ONCE but(!) instead of OR we should use AND logical
operation (thanks Yinghai for spotting the root of the problem).
Along with that we could be have bad MP table and we are
to fix it that way no SMP started and no complains about
BIOS bug if apic was just disabled via command line.
Sergei Shtylyov [Sun, 7 Jun 2009 11:52:50 +0000 (13:52 +0200)]
pdc202xx_old: fix resetproc() method
pdc202xx_reset() calls pdc202xx_reset_host() twice, for both channels, while
that function actually twiddles the single, shared software reset bit -- the
net effect is a duplicated reset and horrendous 4 second delay happening not
only on a channel reset but also when dma_lost_irq() and dma_clear() methods
are called. Fold pdc202xx_reset_host() into pdc202xx_reset(), fix printk(),
and move it before the actual reset...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sun, 7 Jun 2009 11:52:50 +0000 (13:52 +0200)]
pdc202xx_old: fix 'pdc20246_dma_ops'
Commit ac95beedf8bc97b24f9540d4da9952f07221c023 (ide: add struct ide_port_ops
(take 2)) erroneously converted the driver's dma_timeout() and dma_lost_irq()
methods to call the driver's resetproc() method regardless of whether it was
defined for this specific controller while it hadn't been defined and hence
called for PDC20246. So the dma_clear() method, the successor of dma_timeout(),
shouldn't exist and the dma_lost_irq() method should be standard for PDC20246.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Joerg Roedel [Fri, 5 Jun 2009 10:01:35 +0000 (12:01 +0200)]
dma-debug: change hash_bucket_find from first-fit to best-fit
Some device drivers map the same physical address multiple times to a
dma address. Without an IOMMU this results in the same dma address being
put into the dma-debug hash multiple times. With a first-fit match in
hash_bucket_find() this function may return the wrong dma_debug_entry.
This can result in false positive warnings. This patch fixes it by
changing the first-fit behavior of hash_bucket_find() into a best-fit
algorithm.
Linus Torvalds [Sat, 6 Jun 2009 21:33:54 +0000 (14:33 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/pci: fix mmconfig detection with 32bit near 4g
PCI: use fixed-up device class when configuring device
Hugh Dickins [Sat, 6 Jun 2009 20:18:09 +0000 (21:18 +0100)]
integrity: fix IMA inode leak
CONFIG_IMA=y inode activity leaks iint_cache and radix_tree_node objects
until the system runs out of memory. Nowhere is calling ima_inode_free()
a.k.a. ima_iint_delete(). Fix that by calling it from destroy_inode().
Linus Torvalds [Sat, 6 Jun 2009 19:18:14 +0000 (12:18 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
ext3/4 with synchronous writes gets wedged by Postfix
Fix nobh_truncate_page() to not pass stack garbage to get_block()
Al Viro [Wed, 13 May 2009 18:13:40 +0000 (19:13 +0100)]
ext3/4 with synchronous writes gets wedged by Postfix
OK, that's probably the easiest way to do that, as much as I don't like it...
Since iget() et.al. will not accept I_FREEING (will wait to go away
and restart), and since we'd better have serialization between new/free
on fs data structures anyway, we can afford simply skipping I_FREEING
et.al. in insert_inode_locked().
We do that from new_inode, so it won't race with free_inode in any interesting
ways and it won't race with iget (of any origin; nfsd or in case of fs
corruption a lookup) since both still will wait for I_LOCK.
Reviewed-by: "Theodore Ts'o" <tytso@mit.edu> Acked-by: Jan Kara <jack@suse.cz> Tested-by: David Watson <dbwatson@ukfsn.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Theodore Ts'o [Tue, 12 May 2009 11:37:56 +0000 (07:37 -0400)]
Fix nobh_truncate_page() to not pass stack garbage to get_block()
The nobh_truncate_page() function is used by ext2, exofs, and jfs. Of
these three, only ext2 and jfs's get_block() function pays attention
to bh->b_size --- which is normally always the filesystem blocksize
except when the get_block() function is called by either
mpage_readpage(), mpage_readpages(), or the direct I/O routines in
fs/direct_io.c.
Unfortunately, nobh_truncate_page() does not initialize map_bh before
calling the filesystem-supplied get_block() function. So ext2 and jfs
will try to calculate the number of blocks to map by taking stack
garbage and shifting it left by inode->i_blkbits. This should be
*mostly* harmless (except the filesystem will do some unnneeded work)
unless the stack garbage is less than filesystem's blocksize, in which
case maxblocks will be zero, and the attempt to find out whether or
not the filesystem has a hole at a given logical block will fail, and
the page cache entry might not get zero'ed out.
Also if the stack garbage in in map_bh->state happens to have the
BH_Mapped bit set, there could be an attempt to call readpage() on a
non-existent page, which could cause nobh_truncate_page() to return an
error when it should not.
Fix this by initializing map_bh->state and map_bh->size.
Fortunately, it's probably fairly unlikely that ext2 and jfs users
mount with nobh these days.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Cc: linux-fsdevel@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Mark Langsdorf [Sun, 5 Jul 2009 20:50:52 +0000 (15:50 -0500)]
x86: enable GART-IOMMU only after setting up protection methods
The current code to set up the GART as an IOMMU enables GART
translations before it removes the aperture from the kernel memory
map, sets the GART PTEs to UC, sets up the guard and scratch
pages, or does a wbinvd(). This leaves the possibility of cache
aliasing open and can cause system crashes.
Re-order the code so as to enable the GART translations only
after all safeguards are in place and the tlb has been flushed.
AMD has tested this patch on both Istanbul systems and 1st
generation Opteron systems with APG enabled and seen no adverse
effects. Istanbul systems with HT Assist enabled sometimes
see MCE errors due to cache artifacts with the unmodified
code.
Alan Cox [Wed, 13 May 2009 14:02:27 +0000 (15:02 +0100)]
[libata] pata_ali: Use IGN_SIMPLEX
Some ALi devices report simplex if they have been disabled and re-enabled, and
restoring the byte does not work. Ignore it - the needed supporting logic is
already present for the SATA ULi ports.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: Fix oops and use after free during space balancing
Btrfs: set device->total_disk_bytes when adding new device
Linus Torvalds [Fri, 5 Jun 2009 18:53:44 +0000 (11:53 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix: Add HP Compaq nc6000 to the broken poweroff list
ahci: add warning messages for hp laptops with broken suspend
pata_efar: fix PIO2 underclocking
pata_legacy: wait for async probing
Tejun Heo [Sat, 30 May 2009 11:50:12 +0000 (20:50 +0900)]
ahci: add warning messages for hp laptops with broken suspend
Harddisks on HP dv[4-6] and HDX18 fail to come online after resume on
earlier BIOSen. Fortunately, HP recently released BIOS updates for
all machines to fix the issue. Detect old BIOSen, warn the user to
update BIOS on boot and suspend attempts and fail suspend.
Kudos to all the bug reporters.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: kernel.org@epperson.homelinux.net Cc: emisca@gmail.com Cc: Gadi Cohen <dragon@wastelands.net> Cc: Paul Swanson <paul@procursa.com> Cc: s@ourada.org Cc: Trevor Davenport <trevor.davenport@gmail.com> Cc: corruptor1972 <steven_tierney@yahoo.co.uk> Cc: Victoria Wilson <mail@vwilson.co.uk> Cc: khiraly <khiraly.list@gmail.com> Cc: Sean <wollombi@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sergei Shtylyov [Mon, 1 Jun 2009 19:42:10 +0000 (22:42 +0300)]
pata_efar: fix PIO2 underclocking
Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the PIIX/ICH drivers do.
Also, fix/rephrase some comments while at it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
James Bottomley [Fri, 5 Jun 2009 14:41:39 +0000 (10:41 -0400)]
pata_legacy: wait for async probing
The basic problem here that pata_legacy attaches the host, sees if it found
any devices and detaches it if none were found. With async probing, it's not
waiting until discovery is finished before deciding it has no devices and
trying the detach leading to this warning:
One way to fix it would be to put an async_synchronize_full() before looking
for devices, which this patch does. A better way might be to separate libata
into its own domain and only wait for that.
Reported-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dave Jones [Fri, 5 Jun 2009 16:37:07 +0000 (12:37 -0400)]
[CPUFREQ] powernow-k8: check space_id of _PCT registers to be FFH
The powernow-k8 driver checks to see that the Performance Control/Status
Registers are declared as FFH (functional fixed hardware) by the BIOS.
However, this check got broken in the commit: 0e64a0c982c06a6b8f5e2a7f29eb108fdf257b2f
[CPUFREQ] checkpatch cleanups for powernow-k8
Fix based on an original patch from Naga Chumbalkar.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com> Cc: Mark Langsdorf <mark.langsdorf@amd.com> Signed-off-by: Dave Jones <davej@redhat.com>
Alan Cox [Fri, 5 Jun 2009 10:56:18 +0000 (11:56 +0100)]
ivtv: Fix PCI DMA direction
The ivtv stream buffers may be for receive or for send but the attached
sg handle is always destined cpu->device. We flush it correctly but the
allocation is wrongly done with the same type as the buffers.
See bug: http://bugzilla.kernel.org/show_bug.cgi?id=13385
(Note this doesn't close the bug - it fixes the ivtv part and in turn
the logging next shows up some rather alarming DMA sg list warnings in
libata)
Signed-off-by: Alan Cox <alan@linux.intel.com> Acked-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>