Dan Carpenter [Wed, 23 Dec 2009 13:23:19 +0000 (15:23 +0200)]
wl1271_cmd.c: cleanup char => u8
This is just a clean up and doesn't make a functional difference. It keeps the
lint checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 23 Dec 2009 12:12:05 +0000 (13:12 +0100)]
cfg80211: fix race between deauth and assoc response
Joseph Nahmias reported, in http://bugs.debian.org/562016,
that he was getting the following warning (with some log
around the issue):
ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
ath0: direct probe responded
ath0: authenticate with AP 00:11:95:77:e0:b0 (try 1)
ath0: authenticated
ath0: associate with AP 00:11:95:77:e0:b0 (try 1)
ath0: deauthenticating from 00:11:95:77:e0:b0 by local choice (reason=3)
ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
ath0: RX AssocResp from 00:11:95:77:e0:b0 (capab=0x421 status=0 aid=2)
ath0: associated
------------[ cut here ]------------
WARNING: at net/wireless/mlme.c:97 cfg80211_send_rx_assoc+0x14d/0x152 [cfg80211]()
Hardware name: 7658CTO
...
Pid: 761, comm: phy0 Not tainted 2.6.32-trunk-686 #1
Call Trace:
[<c1030a5d>] ? warn_slowpath_common+0x5e/0x8a
[<c1030a93>] ? warn_slowpath_null+0xa/0xc
[<f86cafc7>] ? cfg80211_send_rx_assoc+0x14d/0x152
...
ath0: link becomes ready
ath0: deauthenticating from 00:11:95:77:e0:b0 by local choice (reason=3)
ath0: no IPv6 routers present
ath0: link is not ready
ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
ath0: direct probe responded
ath0: authenticate with AP 00:11:95:77:e0:b0 (try 1)
ath0: authenticated
ath0: associate with AP 00:11:95:77:e0:b0 (try 1)
ath0: RX ReassocResp from 00:11:95:77:e0:b0 (capab=0x421 status=0 aid=2)
ath0: associated
It is not clear to me how the first "direct probe" here
happens, but this seems to be a race condition, if the
user requests to deauth after requesting assoc, but before
the assoc response is received. In that case, it may
happen that mac80211 tries to report the assoc success to
cfg80211, but gets blocked on the wdev lock that is held
because the user is requesting the deauth.
The result is that we run into a warning. This is mostly
harmless, but maybe cause an unexpected event to be sent
to userspace; we'd send an assoc success event although
userspace was no longer expecting that.
To fix this, remove the warning and check whether the
race happened and in that case abort processing.
Reported-by: Joseph Nahmias <joe@nahmias.net> Cc: stable@kernel.org Cc: 562016-quiet@bugs.debian.org Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Tue, 22 Dec 2009 03:26:48 +0000 (22:26 -0500)]
ath5k: fix SWI calibration interrupt storm
The calibration period is now invoked by triggering a software
interrupt from within the ISR by ath5k_hw_calibration_poll()
instead of via a timer.
However, the calibration interval isn't initialized before
interrupts are enabled, so we can have a situation where an
interrupt occurs before the interval is assigned, so the
interval is actually negative. As a result, the ISR will
arm a software interrupt to schedule the tasklet, and then
rearm it when the SWI is processed, and so on, leading to a
softlockup at modprobe time.
Move the initialization order around so the calibration interval
is set before interrupts are active. Another possible fix
is to schedule the tasklet directly from the poll routine,
but I think there are additional plans for the SWI.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 20 Dec 2009 18:07:09 +0000 (19:07 +0100)]
mac80211: fix ibss join with fixed-bssid
When fixed bssid is requested when joining an ibss network, incoming
beacons that match the configured bssid cause mac80211 to create new
sta entries, even before the ibss interface is in joined state.
When that happens, it fails to bring up the interface entirely, because
it checks for existing sta entries before joining.
This patch fixes this bug by refusing to create sta info entries before
the interface is fully operational.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Fri, 18 Dec 2009 10:36:49 +0000 (11:36 +0100)]
libertas: Remove carrier signaling from the scan code
There is no reason to signal a carrier off when doing a 802.11 scan.
Cc: Holger Schurig <holgerschurig@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrey Borzenkov [Tue, 22 Dec 2009 18:38:44 +0000 (21:38 +0300)]
orinoco: fix GFP_KERNEL in orinoco_set_key with interrupts disabled
orinoco_set_key is called from two places both with interrupts disabled
(under orinoco_lock). Use GFP_ATOMIC instead of GFP_KERNEL. Fixes following
warning:
ps3_gelic_wireless: Fix build failure due to missing WEXT_PRIV
The option to support the old style PSK interface in the PS3
GELIC wireless drivers requires CONFIG_WEXT_PRIV to be set
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: rework MLME for multiple authentications
inadvertedly broke WMM because it removed, along with
a bunch of other now useless initialisations, the line
initialising sdata->u.mgd.wmm_last_param_set to -1
which would make it adopt any WMM parameter set. If,
as is usually the case, the AP uses WMM parameter set
sequence number zero, we'd never update it until the
AP changes the sequence number.
Add the missing initialisation back to get the WMM
settings from the AP applied locally.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org [2.6.31+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 17 Dec 2009 12:55:48 +0000 (13:55 +0100)]
mac80211: fix peer HT capabilities
I noticed yesterday, because Jeff had noticed
a speed regression, cf. bug
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2138
that the SM PS settings for peers were wrong.
Instead of overwriting the SM PS settings with
the local bits, we need to keep the remote bits.
The bug was part of the original HT code from
over two years ago, but unfortunately nobody
noticed that it makes no sense -- we shouldn't
be overwriting the peer's setting with our own
but rather keep it intact when masking the peer
capabilities with our own.
While fixing that, I noticed that the masking of
capabilities is completely useless for most of
the bits, so also fix those other bits.
Finally, I also noticed that PSMP_SUPPORT no
longer exists in the final 802.11n version, so
also remove that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roel Kluin [Wed, 16 Dec 2009 16:01:38 +0000 (17:01 +0100)]
iwmc3200wifi: Fix test of unsigned in iwm_ntf_stop_resume_tx()
`queue' was unsigned so the test did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Reviewed-by: Pavel Roskin <proski@gnu.org> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl-tx.c: In function `iwl_hw_txq_ctx_free':
drivers/net/wireless/iwlwifi/iwl-tx.c:410: warning: suggest explicit braces to avoid ambiguous `else'
Cc: Zhu Yi <yi.zhu@intel.com> Cc: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Mon, 14 Dec 2009 11:04:56 +0000 (16:34 +0530)]
ath9k: Stop ANI when doing a reset
The MIB counters are disabled when doing a chip reset.
Since ANI depends on the MIB registers for its operation, relying
on the contents of said registers during HW reset results in sub-optimal
performance.
Cc: stable@kernel.org Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Mon, 14 Dec 2009 09:27:08 +0000 (14:57 +0530)]
ath9k: Fix TX queue draining
When TX DMA termination has failed, the HW has to be reset
completely. Doing a fast channel change in this case is insufficient.
Also, change the debug level of a couple of messages to FATAL.
Cc: stable@kernel.org Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Fix calculation of rt2800 iveiv entry offset.
Fix typo. The index should be multiplied by the entry size, not 'and'-ed.
Found via code-inspection.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Mon, 14 Dec 2009 22:12:11 +0000 (14:12 -0800)]
iwlwifi: initialize spinlock before use
Recent powersaving work resulted in power management ops being called
during EEPROM initialization. The lock used by these functions is not
initialized at this time. Ensure lock is initialized before it is used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Mon, 14 Dec 2009 22:12:10 +0000 (14:12 -0800)]
iwl3945: disable power save
we see from http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2125
that power saving does not work well on 3945. Since then power saving has
also been connected with association problems where an AP deathenticates a
3945 after it is unable to transmit data to it - this happens when 3945
enters power savings mode.
Disable power save support until issues are resolved.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 14 Dec 2009 22:12:09 +0000 (14:12 -0800)]
iwlwifi: fix more eeprom endian bugs
I've also for a long time had a problem with the
temperature calculation code, which I had fixed
by byte-swapping the values, and now it turns out
that was the correct fix after all.
Also, any use of iwl_eeprom_query_addr() that is
for more than a u8 must be cast to little endian,
and some structs as well.
Fix all this. Again, no real impact on platforms
that already are little endian.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 14 Dec 2009 22:12:08 +0000 (14:12 -0800)]
iwlwifi: fix EEPROM/OTP reading endian annotations and a bug
The construct "le16_to_cpu((__force __le16)(r >> 16))" has
always bothered me when looking through the iwlwifi code,
it shouldn't be necessary to __force anything, and before
this code, "r" was obtained with an ioread32, which swaps
each of the two u16 values in it properly when swapping the
entire u32 value. I've had arguments about this code with
people before, but always conceded they were right because
removing it only made things not work at all on big endian
platforms.
However, analysing a failure of the OTP reading code, I now
finally figured out what is going on, and why my intuition
about that code being wrong was right all along.
It turns out that the 'priv->eeprom' u8 array really wants
to have the data in it in little endian. So the force code
above and all really converts *to* little endian, not from
it. Cf., for instance, the function iwl_eeprom_query16() --
it reads two u8 values and combines them into a u16, in a
little-endian way. And considering it more, it makes sense
to have the eeprom array as on the device, after all not
all values really are 16-bit values, the MAC address for
instance is not.
Now, what this really means is that all the annotations are
completely wrong. The eeprom reading code should fill the
priv->eeprom array as a __le16 array, with __le16 values.
This also means that iwl_read_otp_word() should really have
a __le16 pointer as the data argument, since it should be
filling that in a format suitable for priv->eeprom.
Propagating these changes throughout, iwl_find_otp_image()
is found to be, now obviously visible, defective -- it uses
the data returned by iwl_read_otp_word() directly as if it
was CPU endianness. Fixing that, which is this hunk of the
patch:
is the only real change of this patch. Everything else is
just fixing the sparse annotations.
Also, the bug only shows up on big endian platforms with a
1000 series card. 5000 and previous series do not use OTP,
and 6000 series has shadow RAM support which means we don't
ever use the defective code on any cards but 1000.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Disable powersaving for rt61pci and rt2800pci.
We've had many reports of rt61pci failures with powersaving enabled.
Therefore, as a stop-gap measure, disable powersaving of the rt61pci
until we have found a proper solution.
Also disable powersaving on rt2800pci as it most probably will show
the same problem.
Cc: stable@kernel.org Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Sun, 13 Dec 2009 16:07:45 +0000 (17:07 +0100)]
drivers/net/wireless: Correct code taking the size of a pointer
sizeof(iv16) and sizeof(iv32) are the sizes of pointers. Change them to
the size of the copied data.
Furthermore, iveiv_entry is a local structure that has just been
initialized and is not visible outside this function. Thus, there would
seem to be no point to copy data into it. The order of the arguments is
thus changed to copy the data into the parameters, which are provided as
pointers, suggesting in this case that they should be used to return values.
A simplified version of the semantic patch that finds the first problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
First, we copy/paste the padding stuff from ath9k_tx to ath_tx_cabq since it
needs to same kind of padding, but for internally generated beacons.
Next, software padding done on TX needs to be removed before calling
ieee80211_tx_status. The code was already there in ath_tx_complete but it
was wrong. Fix it by using ath9k_cmn_padpos. This later code has been
tested by sending packets to a monitor interface and reading packets from the
same interface.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 10 Dec 2009 22:37:23 +0000 (14:37 -0800)]
iwlwifi: fix syslog message for event log dump size
When trigger event log dumping from debugfs, the entire event log
should be dumped and the size should match the number of events being
dump.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Thu, 10 Dec 2009 22:37:22 +0000 (14:37 -0800)]
iwlwifi: power up all devices for EEPROM read
Recent commits "iwlwifi: remove power-wasting calls to apm_ops.init()" and
"iwlagn: power up device before initializing EEPROM" had the goal of
reducing device power consumption from the time the module is loaded until
the interface is brought up and the device's power saving mechanisms kick
in. The idea is that once the module is loaded there is no need for the
device to consume power until the interface is brought up.
With the current solution the device is only powered up during EEPROM read,
and then so also only if the EEPROM type is OTP. We have found that on
certain platforms even non-OTP devices require power to be up during EEPROM
read. On these platforms the driver never loads and the system log contains
the following:
iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080403D8
We thus now power up all devices during EEPROM read.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 10 Dec 2009 22:37:21 +0000 (14:37 -0800)]
iwlwifi: allocated rx page accounting cleanup
In iwlwifi, priv->alloc_rxb_page is used to keep track of the Rx
pages allocated by the driver. This cleans up the page free routines
by introducing __iwl_free_pages/iwl_free_pages so that the accounting
is more accurate and less error prone. This also fixes two instances where
the counter was not updated.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Add define for TX headroom reserved by mac80211 itself.
Add a definition of the amount of TX headroom reserved by mac80211 itself
for its own purposes. Also add BUILD_BUG_ON to validate the value.
This define can then be used by drivers to request additional TX headroom
in the most efficient manner.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800lib incorrectly detected whether RT2800USB was enabled because
it didn't account for a modularized RT2800USB driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Thu, 10 Dec 2009 02:43:01 +0000 (18:43 -0800)]
mac80211: Revert 'Use correct sign for mesh active path refresh'
The patch ("mac80211: Use correct sign for mesh active path
refresh.") was actually a bug. Reverted it and improved the
explanation of how mesh path refresh works.
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Thu, 10 Dec 2009 02:43:00 +0000 (18:43 -0800)]
mac80211: Fixed bug in mesh portal paths
Paths to mesh portals were being timed out immediately after each use in
intermediate forwarding nodes. mppath->exp_time is set to the expiration time
so assigning it to jiffies was marking the path as expired.
Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 9 Dec 2009 19:25:56 +0000 (13:25 -0600)]
b43: Remove reset after fatal DMA error
As shown in Kernel Bugzilla #14761, doing a controller restart after a
fatal DMA error does not accomplish anything other than consume the CPU
on an affected system. Accordingly, substitute a meaningful message for
the restart.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [2.6.32] Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: add radio led and fix warnings on suspend
Michael Buesch reports that his rtl8187 gives warnings on suspend
("queueing ieee80211 work while going to suspend" warnings), as rtl8187
can call ieee80211_queue_delayed_work after mac80211 is suspended.
This change enhances rtl8187 led code so we can avoid queuing work after
mac80211 is suspended: now we register a radio led and make additional
checks to ensure led is off/on properly as mac80211 wants.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this we have no gaurantee of the integrity of the
EEPROM and are likely to encounter a lot of bogus bug reports
due to actual issues on the EEPROM. With the EEPROM checksum
check in place we can easily rule those issues out.
If you run patch during a revert *you* have a card with a busted
EEPROM and only older kernel will support that concoction. This
patch is a trade off between not accepitng bogus EEPROMs and
avoiding bogus bug reports allowing developers to focus instead
on real concrete issues.
If stable keeps bogus bug reports because of a possibly busted EEPROM
feel free to apply this there too.
Tested on an AR5414
Cc: stable@kernel.org Cc: jirislaby@gmail.com Cc: akpm@linux-foundation.org Cc: rjw@sisk.pl Cc: me@bobcopeland.com Cc: david.quan@atheros.com Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Tue, 24 Nov 2009 16:54:10 +0000 (11:54 -0500)]
cfg80211: Clear encryption privacy when key off is done.
When the current_bss is not set, 'iwconfig <iface> key off' does not
clear the private flag. Hence after we connect with WEP to an AP and
then try to connect with another non-WEP AP, it does not work.
This issue will not be seen if supplicant is used.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC ggianfar.o
ggianfar.c: In function 'gfar_netpoll':
ggianfar.c:2653: error: invalid storage class for function 'gfar_interrupt'
ggianfar.c:2652: warning: ISO C90 forbids mixed declarations and code
ggianfar.c:2681: error: invalid storage class for function 'adjust_link'
ggianfar.c:2764: error: invalid storage class for function 'gfar_set_multi'
ggianfar.c:2855: error: invalid storage class for function 'gfar_clear_exact_match'
ggianfar.c:2877: error: invalid storage class for function 'gfar_set_hash_for_addr'
ggianfar.c:2898: error: invalid storage class for function 'gfar_set_mac_for_addr'
ggianfar.c:2922: error: invalid storage class for function 'gfar_error'
ggianfar.c:3020: warning: ISO C90 forbids mixed declarations and code
ggianfar.c:3032: error: invalid storage class for function 'gfar_init'
ggianfar.c:3037: error: invalid storage class for function 'gfar_exit'
ggianfar.c:3041: error: initializer element is not constant
ggianfar.c:3042: error: initializer element is not constant
ggianfar.c:3042: warning: ISO C90 forbids mixed declarations and code
ggianfar.c:3042: error: expected declaration or statement at end of input
make[1]: *** [ggianfar.o] Error 1
This patch fixes the issue.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
b44 WOL setup: one-bit-off stack corruption kernel panic fix
About 50% of shutdowns of b44 Ethernet adapter ends by kernel panic
with kernels compiled with stack-protector.
Checking b44_magic_pattern() return values, one call of
b44_magic_pattern() returns 127. It means, that set_bit(128, pmask)
was called on line 1509. It means that bit 0 of 17th byte of pmask was
overwritten. But pmask has only 16 bytes. Stack corruption happens.
It seems that set_bit() on line 1509 always writes one bit off.
The fix does not only solve the stack corruption, but also makes Wake
On LAN working on my onboard B44 on Asus A7V-333X mainboard.
It seems that this problem affects all kernel versions since commit 725ad800 ([PATCH] b44: add wol for old nic) on 2006-06-20.
Signed-off-by: Stanislav Brabec <sbrabec@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Wed, 9 Dec 2009 04:54:11 +0000 (20:54 -0800)]
tcp: fix retrans_stamp advancing in error cases
It can happen, that tcp_retransmit_skb fails due to some error.
In such cases we might end up into a state where tp->retrans_out
is zero but that's only because we removed the TCPCB_SACKED_RETRANS
bit from a segment but couldn't retransmit it because of the error
that happened. Therefore some assumptions that retrans_out checks
are based do not necessarily hold, as there still can be an old
retransmission but that is only visible in TCPCB_EVER_RETRANS bit.
As retransmission happen in sequential order (except for some very
rare corner cases), it's enough to check the head skb for that bit.
Main reason for all this complexity is the fact that connection dying
time now depends on the validity of the retrans_stamp, in particular,
that successive retransmissions of a segment must not advance
retrans_stamp under any conditions. It seems after quick thinking that
this has relatively low impact as eventually TCP will go into CA_Loss
and either use the existing check for !retrans_stamp case or send a
retransmission successfully, setting a new base time for the dying
timer (can happen only once). At worst, the dying time will be
approximately the double of the intented time. In addition,
tcp_packet_delayed() will return wrong result (has some cc aspects
but due to rarity of these errors, it's hardly an issue).
One of retrans_stamp clearing happens indirectly through first going
into CA_Open state and then a later ACK lets the clearing to happen.
Thus tcp_try_keep_open has to be modified too.
Thanks to Damian Lukowski <damian@tvk.rwth-aachen.de> for hinting
that this possibility exists (though the particular case discussed
didn't after all have it happening but was just a debug patch
artifact).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem in the TCP connection timeout calculation.
Currently, timeout decisions are made on the basis of the current
tcp_time_stamp and retrans_stamp, which is usually set at the first
retransmission.
However, if the retransmission fails in tcp_retransmit_skb(),
retrans_stamp is not updated and remains zero. This leads to wrong
decisions in retransmits_timed_out() if tcp_time_stamp is larger than
the specified timeout, which is very likely.
In this case, the TCP connection dies after the first attempted
(and unsuccessful) retransmission.
With this patch, tcp_skb_cb->when is used instead, when retrans_stamp
is not available.
This bug has been introduced together with retransmits_timed_out() in
2.6.32, as the number of retransmissions has been used for timeout
decisions before. The corresponding commit was 6fa12c85031485dff38ce550c24f10da23b0adaa (Revert Backoff [v3]:
Calculate TCP's connection close threshold as a time value.).
Thanks to Ilpo Järvinen for code suggestions and Frederic Leroy for
testing.
Reported-by: Frederic Leroy <fredo@starox.org> Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de> Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Yang [Sun, 6 Dec 2009 22:56:59 +0000 (22:56 +0000)]
atl1c:add pci map direction in atl1c_buffer flags
add pci map direction in atl1c_buffer flags, it is used when call pci_unmap
apis. Signed-off-by: Jie Yang <jie.yang@atheros.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Unified firmware image may not contain MN type of firmware.
Driver should fall back to NOMN firmware type instead
of going to flash.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
o netif_running() check for enabling interrupt at end of napi poll is
not enough to cover firmwar recovery. Instead test __NX_DEV_UP bit.
o Avoid re-entry into to netxen_nic_down() with __NX_DEV_UP bit check.
Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
o To prevent race conditions with other reset events.
During suspend/resume and firmware recovery, acquire rtnl_lock,
while changing interface state.
Acked-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Asier Llano [Wed, 9 Dec 2009 04:29:10 +0000 (20:29 -0800)]
net/mpc5200: Fix locking on fec_mpc52xx driver
Fix the locking scheme on the fec_mpc52xx driver. This device can
receive IRQs from three sources; the FEC itself, the tx DMA, and the
rx DMA. Mutual exclusion was handled by taking a spin_lock() in the
critical regions, but because the handlers are run with IRQs enabled,
spin_lock() is insufficient and the driver can end up interrupting
a critical region anyway from another IRQ.
Asier Llano discovered that this occurs when an error IRQ is raised
in the middle of handling rx irqs which resulted in an sk_buff memory
leak.
In addition, locking is spotty at best in the driver and inspection
revealed quite a few places with insufficient locking.
This patch is based on Asier's initial work, but reworks a number of
things so that locks are held for as short a time as possible, so
that spin_lock_irqsave() is used everywhere, and so the locks are
dropped when calling into the network stack (because the lock only
protects the hardware interface; not the network stack).
Boot tested on a lite5200 with an NFS root. Has not been performance
tested.
Signed-off-by: Asier Llano <a.llano@ziv.es> Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
in routed mode, we don't have a hardware address so netdev_ops doesnt
need to validate our hardware address via .ndo_validate_addr
Reported-by: Manuel Fuentes <mfuentes@agenciaefe.com> Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 9 Dec 2009 04:19:53 +0000 (20:19 -0800)]
[PATCH] tcp: documents timewait refcnt tricks
Adds kerneldoc for inet_twsk_unhash() & inet_twsk_bind_unhash().
With help from Randy Dunlap.
Suggested-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 4 Dec 2009 03:47:42 +0000 (03:47 +0000)]
tcp: Fix a connect() race with timewait sockets
When we find a timewait connection in __inet_hash_connect() and reuse
it for a new connection request, we have a race window, releasing bind
list lock and reacquiring it in __inet_twsk_kill() to remove timewait
socket from list.
Another thread might find the timewait socket we already chose, leading to
list corruption and crashes.
Fix is to remove timewait socket from bind list before releasing the bind lock.
Note: This problem happens if sysctl_tcp_tw_reuse is set.
Reported-by: kapil dakhane <kdakhane@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 4 Dec 2009 03:46:54 +0000 (03:46 +0000)]
tcp: Fix a connect() race with timewait sockets
First patch changes __inet_hash_nolisten() and __inet6_hash()
to get a timewait parameter to be able to unhash it from ehash
at same time the new socket is inserted in hash.
This makes sure timewait socket wont be found by a concurrent
writer in __inet_check_established()
Reported-by: kapil dakhane <kdakhane@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Don Skidmore [Tue, 8 Dec 2009 07:22:23 +0000 (07:22 +0000)]
ixgbe: add support for 82599 KR device 0x1517
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 8 Dec 2009 07:22:03 +0000 (07:22 +0000)]
ixgbe: Fix TX stats accounting
Here is an updated version, because ixgbe_get_ethtool_stats()
needs to call dev_get_stats() or "ethtool -S" wont give
correct tx_bytes/tx_packets values.
Several cpus can update netdev->stats.tx_bytes & netdev->stats.tx_packets
in parallel. In this case, TX stats are under estimated and false sharing
takes place.
Multi queue devices should instead use txq->tx_bytes & txq->tx_packets
in their xmit() method (appropriate txq lock already held by caller, no
cache line miss), or use appropriate locking.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 8 Dec 2009 07:28:20 +0000 (07:28 +0000)]
e1000e: only perform ESB2 MDIC workaround on certain configurations
A workaround added for all ESB2 devices (adds a delay for all MDIC accesses
which resolves an issue with the MDIC ready bit being set prematurely) is
applicable only to devices in which the MAC-PHY interconnect is not
operating in a certain mode with in-band MDIO. Check the control register
for the operating mode and enable the workaround accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 8 Dec 2009 07:28:01 +0000 (07:28 +0000)]
e1000e: replace incorrect use of GG82563_REG macro
The GG82563_REG() macro should not be used to determine the offset provided
to the e1000e_[read|write]_kmrn_reg() functions since the first argument to
the macro is already implied and gets masked off anyway in the functions.
The resultant register reads/writes with this patch are functionally the
same as before.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 8 Dec 2009 07:27:41 +0000 (07:27 +0000)]
e1000e: minor correction to name of bit in CTRL_EXT register
Bit 7 in the CTRL_REG register is actually the Software Definable Pin 3,
not the Software Definable Pin 7.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 8 Dec 2009 20:51:22 +0000 (12:51 -0800)]
sctp: fix compile error due to sysctl mismerge
I messed up the merge in d7fc02c7bae7b1cf69269992cf880a43a350cdaa, where
the conflict in question wasn't just about CTL_UNNUMBERED being removed,
but the 'strategy' field is too (sysctl handling is now done through the
/proc interface, with no duplicate protocols for reading the data).
Linus Torvalds [Tue, 8 Dec 2009 16:19:16 +0000 (08:19 -0800)]
Merge branch 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
cfq-iosched: Do not access cfqq after freeing it
block: include linux/err.h to use ERR_PTR
cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
blkio: Allow CFQ group IO scheduling even when CFQ is a module
blkio: Implement dynamic io controlling policy registration
blkio: Export some symbols from blkio as its user CFQ can be a module
block: Fix io_context leak after failure of clone with CLONE_IO
block: Fix io_context leak after clone with CLONE_IO
cfq-iosched: make nonrot check logic consistent
io controller: quick fix for blk-cgroup and modular CFQ
cfq-iosched: move IO controller declerations to a header file
cfq-iosched: fix compile problem with !CONFIG_CGROUP
blkio: Documentation
blkio: Wait on sync-noidle queue even if rq_noidle = 1
blkio: Implement group_isolation tunable
blkio: Determine async workload length based on total number of queues
blkio: Wait for cfq queue to get backlogged if group is empty
blkio: Propagate cgroup weight updation to cfq groups
blkio: Drop the reference to queue once the task changes cgroup
blkio: Provide some isolation between groups
...
Linus Torvalds [Tue, 8 Dec 2009 16:18:01 +0000 (08:18 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
Linus Torvalds [Tue, 8 Dec 2009 16:13:35 +0000 (08:13 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: parport_mfc3 - Not makes it a bool before the comparison.
m68k: don't export static inline functions
fbdev: atafb - add palette register check
m68k: Remove the BKL from sys_execve
m68k: Cleanup linker scripts using new linker script macros.
m68k: Make thread_info.h usable from assembly.
m68knommu: define arch_has_single_step() and friends
m68k: ptrace fixes
m68k: use generic code for ptrace requests
rtc: Add an RTC driver for the Ricoh RP5C01
rtc: Add an RTC driver for the Oki MSM6242
Linus Torvalds [Tue, 8 Dec 2009 16:12:16 +0000 (08:12 -0800)]
Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-stub: Documentation update
i2c-stub: Allow user to disable some commands
i2c-stub: Implement I2C block support
i2c: Refactor for_each callbacks
i2c-i801: Retry on lost arbitration
i2c: Remove big kernel lock from i2cdev_open
ics932s401: Clean up detect function
i2c: Simplify i2c_detect_address
i2c: Drop probe, ignore and force module parameters
i2c: Add missing __devinit markers to old i2c adapter drivers
i2c: Bus drivers don't have to support I2C_M_REV_DIR_ADDR
i2c: Prevent priority inversion on top of bus lock
i2c-voodoo3: Delete
i2c-powermac: Drop temporary name buffer
i2c-powermac: Include the i2c_adapter in struct pmac_i2c_bus
i2c-powermac: Log errors
i2c-powermac: Refactor i2c_powermac_smbus_xfer
i2c-powermac: Reject unsupported I2C transactions
i2c/chips: Move ds1682 to drivers/misc
Linus Torvalds [Tue, 8 Dec 2009 16:07:16 +0000 (08:07 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Add flag for devices capable of generating run-time wake-up events
PM / Runtime: Remove unnecessary braces in __pm_runtime_set_status()
PM / Runtime: Make documentation of runtime_idle() agree with the code
PM / Runtime: Ensure timer_expires is nonzero in pm_schedule_suspend()
PM / Runtime: Use deferred_resume flag in pm_request_resume
PM / Runtime: Export the PM runtime workqueue
PM / Runtime: Fix lockdep warning in __pm_runtime_set_status()
PM / Hibernate: Swap, use KERN_CONT
PM / Hibernate: Shift remaining code from swsusp.c to hibernate.c
PM / Hibernate: Move swap functions to kernel/power/swap.c.
PM / freezer: Don't get over-anxious while waiting
Linus Torvalds [Tue, 8 Dec 2009 16:02:38 +0000 (08:02 -0800)]
Merge branch 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (84 commits)
KVM: VMX: Fix comparison of guest efer with stale host value
KVM: s390: Fix prefix register checking in arch/s390/kvm/sigp.c
KVM: Drop user return notifier when disabling virtualization on a cpu
KVM: VMX: Disable unrestricted guest when EPT disabled
KVM: x86 emulator: limit instructions to 15 bytes
KVM: s390: Make psw available on all exits, not just a subset
KVM: x86: Add KVM_GET/SET_VCPU_EVENTS
KVM: VMX: Report unexpected simultaneous exceptions as internal errors
KVM: Allow internal errors reported to userspace to carry extra data
KVM: Reorder IOCTLs in main kvm.h
KVM: x86: Polish exception injection via KVM_SET_GUEST_DEBUG
KVM: only clear irq_source_id if irqchip is present
KVM: x86: disallow KVM_{SET,GET}_LAPIC without allocated in-kernel lapic
KVM: x86: disallow multiple KVM_CREATE_IRQCHIP
KVM: VMX: Remove vmx->msr_offset_efer
KVM: MMU: update invlpg handler comment
KVM: VMX: move CR3/PDPTR update to vmx_set_cr3
KVM: remove duplicated task_switch check
KVM: powerpc: Fix BUILD_BUG_ON condition
KVM: VMX: Use shared msr infrastructure
...
Trivial conflicts due to new Kconfig options in arch/Kconfig and kernel/Makefile
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6:
sparc: Set UTS_MACHINE correctly.
sparc,leon: init_leon srmmu cleanup
sparc32: Remove early interrupt enable.
sparc, leon: Added Aeroflex Gaisler entry in manufacturer_info structure
sparc64: Faster early-boot framebuffer console.
Revert "sparc: Make atomic locks raw"
sparc: remove unused nfsd #includes
sparc: Fixup last users of irq_chip->typename
Added sparc_leon3_snooping_enabled() and converted extern inline to static inline
No auxio on LEON
apbuart: Use of_find_node_by_path to find root node.
sparc: Replace old style lock initializer
sparc: Make atomic locks raw
apbuart: Fix build and missing driver unregister.
apbuart: Kill dependency on deprecated Sparc-only PROM interfaces.
apbuart: Fix build warning.
sparc: Support for GRLIB APBUART serial port
watchdog: Remove BKL from rio watchdog driver
sparc: Remove BKL from apc
sparc,leon: Sparc-Leon SMP support
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
security/tomoyo: Remove now unnecessary handling of security_sysctl.
security/tomoyo: Add a special case to handle accesses through the internal proc mount.
sysctl: Drop & in front of every proc_handler.
sysctl: Remove CTL_NONE and CTL_UNNUMBERED
sysctl: kill dead ctl_handler definitions.
sysctl: Remove the last of the generic binary sysctl support
sysctl net: Remove unused binary sysctl code
sysctl security/tomoyo: Don't look at ctl_name
sysctl arm: Remove binary sysctl support
sysctl x86: Remove dead binary sysctl support
sysctl sh: Remove dead binary sysctl support
sysctl powerpc: Remove dead binary sysctl support
sysctl ia64: Remove dead binary sysctl support
sysctl s390: Remove dead sysctl binary support
sysctl frv: Remove dead binary sysctl support
sysctl mips/lasat: Remove dead binary sysctl support
sysctl drivers: Remove dead binary sysctl support
sysctl crypto: Remove dead binary sysctl support
sysctl security/keys: Remove dead binary sysctl support
sysctl kernel: Remove binary sysctl logic
...
Larry Finger [Sun, 6 Dec 2009 01:25:22 +0000 (19:25 -0600)]
rtl8187: Fix wrong rfkill switch mask for some models
There are different bits used to convey the setting of the rfkill
switch to the driver. The current driver only supports one of these
possibilities. These changes were derived from the latest version
of the vendor driver.
This patch fixes the regression noted in kernel Bugzilla #14743.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-and-tested-by: Antti Kaijanmäki <antti@kaijanmaki.net> Tested-by: Hin-Tak Leung <hintak.leung@gmail.com> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 5 Dec 2009 17:08:05 +0000 (18:08 +0100)]
ath9k: fix tx status reporting
This patch fixes a bug in ath9k's tx status check, which
caused mac80211 to consider regularly transmitted unicast frames
as un-acked.
When checking the ts_status field for errors, it needs to be masked
with ATH9K_TXERR_FILT, because this field also contains other fields
like ATH9K_TX_ACKED.
Without this patch, AP mode is pretty much unusable, as hostapd
checks the ACK status for the frames that it injects.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Fix bug in computing crc over dynamic IEs in beacon
On a 32-bit machine, BIT() macro does not give the required
bit value if the bit is mroe than 31. In ieee802_11_parse_elems_crc(),
BIT() is suppossed to get the bit value more than 31 (42 (id of ERP_INFO_IE),
37 (CHANNEL_SWITCH_IE), (42), 32 (POWER_CONSTRAINT_IE), 45 (HT_CAP_IE),
61 (HT_INFO_IE)). As we do not get the required bit value for the above
IEs, crc over these IEs are never calculated, so any dynamic change in these
IEs after the association is not really handled on 32-bit platforms.
This patch fixes this issue.
Cc: stable@kernel.org Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrew Morton [Fri, 4 Dec 2009 04:45:07 +0000 (20:45 -0800)]
net/rfkill/core.c: work around gcc-4.0.2 silliness
net/rfkill/core.c: In function 'rfkill_type_show':
net/rfkill/core.c:610: warning: control may reach end of non-void function 'rfkill_get_type_str' being inlined
A gcc bug, but simple enough to squish.
Cc: John W. Linville <linville@tuxdriver.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: don't complain about oversized beacons in FINALIZE_JOIN
The FINALIZE_JOIN firmware command only looks at the first couple of
fields in the beacon, and therefore it's not necessary to complain if
the beacon is longer than 128 bytes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: don't overwrite mwl8k_vif::bssid until after disassociation
When disassociating, mac80211 zeroes vif->bss_info.bssid before
calling our ->bss_info_changed(), but we need the BSSID to remove the
hardware station database entry for our AP, so we can't clear our
local copy of the BSSID until after we've done that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time between loading the helper image and starting to upload the
main firmware image should be at least 5 ms or so. We were doing an
msleep(1) before, and 1 ms appears to not be enough in almost all
cases, but building with HZ=100 has always masked this so far. Bumping
the msleep argument to 5 fixes firmware loading e.g. when HZ=1000.
Some firmware images need more than 200ms to initialize. Bump the
ready code timeout to 500ms to accommodate for this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: allow more time for transmit rings to drain
Before issuing any firmware commands, we wait for the transmit rings
to drain, to prevent control versus data path synchronization issues.
In some cases, this can end up taking longer than the current hardcoded
limit of 5 seconds, for example if the transmit rings are filled with
packets for a host that has dropped off the air and we end up
retransmitting every pending packet at the lowest rate a couple of
times.
This patch changes mwl8k_tx_wait_empty() to only bail out on timeout
expiry if there was no change in the number of packets pending in the
transmit rings during the waiting period. If at least one transmit
ring entry was reclaimed while we were waiting, we are apparently still
making progress, and we'll allow waiting for another timeout period.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: allow more time for firmware commands to complete
Some firmware commands can under some circumstances take more than 2
seconds to complete. This patch bumps the timeout up to 10 seconds,
and prints a message whenever a command takes more than 2 seconds.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>