Bruce Allan [Tue, 20 Mar 2012 03:47:52 +0000 (03:47 +0000)]
e1000e: 82579 potential system hang on stress when ME enabled
Previously, a workaround was added to address a hardware bug in the
PCIm2PCI arbiter where a write by the driver of the Transmit/Receive
Descriptor Tail register could happen concurrently with a write of any
MAC CSR register by the Manageability Engine (ME) which could cause the
Tail register to have an incorrect value. The arbiter is supposed to
prevent the concurrent writes but there is a bug that can cause the Host
(driver) access to be acknowledged later than it should.
After further investigation, it was discovered that a driver write access
of any MAC CSR register after being idle for some time can be lost when
ME is accessing a MAC CSR register. When this happens, no further target
access is claimed by the MAC which could hang the system.
The workaround to check bit 24 in the FWSM register (set only when ME is
accessing a MAC CSR register) and delay for a limited amount of time until
it is cleared is now done for all driver writes of MAC CSR registers on
82579 with ME enabled. In the rare case when the driver is writing the
Tail register and ME is accessing any MAC CSR register for a duration
longer than the maximum delay, write the register and verify it has the
correct value before continuing, otherwise reset the device.
This patch also moves some pre-existing macros from the hardware-specific
header file to the more appropriate generic driver header file.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Tue, 20 Mar 2012 03:47:47 +0000 (03:47 +0000)]
e1000e: 82579 packet drop workaround
In K1 mode (a MAC/PHY interconnect power mode), the 82579 device shuts down
the Phase Lock Loop (PLL) of the interconnect to save power. When the PLL
starts working, the 82579 device may start to transfer the packet through
the interconnect before it is fully functional causing packet drops. This
workaround disables shutting down the PLL in K1 mode for 1G link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Fri, 16 Mar 2012 09:02:59 +0000 (09:02 +0000)]
e1000e: Enable DMA Burst Mode on 82574 by default.
Performance testing has shown that enabling DMA burst on 82574
improves performance on small packets, so enable it by default.
Signed-off-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matthew Vick [Fri, 16 Mar 2012 09:02:58 +0000 (09:02 +0000)]
e1000e: Disable Far-End LoopBack following reset on 80003ES2LAN.
80003ES2LAN has an errata such that far-end loopback may be activated by
bit errors producing a reserved symbol. In order to disable far-end
loopback quickly enough, disable it immediately following a reset.
Signed-off-by: Matthew Vick <matthew.vick@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
qlcnic: Allow a predefined set of capture masks for FW dump
o 0x3, 0x7, 0xF, 0x1F, 0x3F, 0x7F and 0xFF are the allowed capture masks.
o Updated driver version to 5.0.28
Signed-off-by: Manish chopra <manish.chopra@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
o Without failing probe, register netdevice when device is in FAILED state.
o Device will come up with minimum functionality.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Include the header to pickup the definitions of the global symbols.
Quiets the following sparse warnings:
warning: symbol 'crush_find_rule' was not declared. Should it be static?
warning: symbol 'crush_do_rule' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Sage Weil <sage@newdream.net> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
isdn/eicon: use standard __init,__exit function markup
Remove the custom DIVA_{INIT,EXIT}_FUNCTION defines and use
the standard __init,__exit markup.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Armin Schindler <mac@melware.de> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Tore Anderson from :
https://bugzilla.kernel.org/show_bug.cgi?id=42572
When RTAX_FEATURE_ALLFRAG is set on a route, the effective TCP segment
size does not take into account the size of the IPv6 Fragmentation
header that needs to be included in outbound packets, causing every
transmitted TCP segment to be fragmented across two IPv6 packets, the
latter of which will only contain 8 bytes of actual payload.
RTAX_FEATURE_ALLFRAG is typically set on a route in response to
receving a ICMPv6 Packet Too Big message indicating a Path MTU of less
than 1280 bytes. 1280 bytes is the minimum IPv6 MTU, however ICMPv6
PTBs with MTU < 1280 are still valid, in particular when an IPv6
packet is sent to an IPv4 destination through a stateless translator.
Any ICMPv4 Need To Fragment packets originated from the IPv4 part of
the path will be translated to ICMPv6 PTB which may then indicate an
MTU of less than 1280.
The Linux kernel refuses to reduce the effective MTU to anything below
1280 bytes, instead it sets it to exactly 1280 bytes, and
RTAX_FEATURE_ALLFRAG is also set. However, the TCP segment size appears
to be set to 1240 bytes (1280 Path MTU - 40 bytes of IPv6 header),
instead of 1232 (additionally taking into account the 8 bytes required
by the IPv6 Fragmentation extension header).
This in turn results in rather inefficient transmission, as every
transmitted TCP segment now is split in two fragments containing
1232+8 bytes of payload.
After this patch, all the outgoing packets that includes a
Fragmentation header all are "atomic" or "non-fragmented" fragments,
i.e., they both have Offset=0 and More Fragments=0.
With help from David S. Miller
Reported-by: Tore Anderson <tore@fud.no> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Tom Herbert <therbert@google.com> Tested-by: Tore Anderson <tore@fud.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Wed, 25 Apr 2012 23:43:04 +0000 (23:43 +0000)]
tcp repair: Fix unaligned access when repairing options (v2)
Don't pick __u8/__u16 values directly from raw pointers, but instead use
an array of structures of code:value pairs. This is OK, since the buffer
we take options from is not an skb memory, but a user-to-kernel one.
For those options which don't require any value now, require this to be
zero (for potential future extension of this API).
v2: Changed tcp_repair_opt to use two __u32-s as spotted by David Laight.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Added support for fragmentation of E1 interfaces of hfcmulti driver.
Fragmentation is usefull if multiple devices are connected to an E1
interface. Each fragment will have a subset of the available timeslots.
These devices require a cascde connection or a multiplexer.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Rework of LED status display for HFC-4S/8S/E1 cards.
LEDs will show RED if layer 1 is disabled or fails.
LEDs will show GREEN if layer 1 is active.
LEDs will blink if traffic on D-channel.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Using FLG_ACTIVE flag to determine if layer 1 is active or not.
We already have the flag for L1 active, so we should use it.
L2 will be solved in a later patch.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Fixed false interruption of audio during bridging change.
Transmitted audio data was interrupted if a bridge was enabled or disabled.
Now transmission seamlessly continues during that action.
Fix in hfcmulti.ko
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
merge TXQ/RXQ/MAC start/enable code to one function as they
are started/enabled at the same time, just like stop/disable them
in the function of atl1c_stop_mac.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This function is used for suspend of S1/S3/S4 and driver remove.
It sets MAC/PHY based on the WoL configuation to get lower power
consumption.
atl1c_phy_power_saving is renamed to atl1c_phy_to_ps_link, this
function is just make PHY enter a link/speed mode to eat less
power.
REG_MAC_CTRL register is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Many magic data are re-configured for PHY during its reset operation
based on chip type to get better compability and stability.
REG_PHY_CTRL register may be configured by BIOS before enter OS.
so, the driver can't directly write to it without any Read-Op.
this change also affect suspend and phy_disable routines.
PHY debug ports and extension registers are refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bit 17/18 of reg1424 must be clear for l2cb 1.x, or it will cause
the write-reg operation fail without cable connected.
so, please do connect the cable when apply this patch to the driver
to make sure these 2bits are cleared by new driver.
The revised code is move to al1c_reset_mac.
SERDES register definition is refined as well.
when do reset MAC, speed/duplex control right should be transferred
to software before do PHY auto-neg -- by bit MASTER_CTRL_SPEED_MODE_SW.
SERDES register definition is refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
phy register is read/write via MDIO control module ---
that module will be affected by the hibernate status,
to access phy regs in hib stutus, slow frequency clk must
be selected.
To access phy extension register, the MDIO related
registers are refined/updated, a _core function is
re-wroted for both regular PHY regs and extension regs.
existing PHY r/w function is revised based on the _core.
PHY extension registers will be used for the comming
patches.
Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Skip flashing a FW component if that component is not present in a
particular FW UFI image.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com> Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
be2net: Fix wrong status getting returned for MCC commands
MCC Response CQEs are processed as part of NAPI poll routine and
also synchronously. If MCC completions are consumed by NAPI poll
routine, wrong status is returned to synchronously waiting routine.
Fix this by getting status of MCC command from command response
instead of response CQEs.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
EQ is getting armed wrongly in INTx mode as INTx interrupt is taking
some time to deassert. This can cause another interrupt while NAPI is
scheduled and scheduling a NAPI in interrupt does not take effect.
This causes interrupt to be missed and traffic stalls. Fixing this by
preventing wrong arming of EQ.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN and multicast hardware filters are limited and can get
exhausted in adapters with many PCI functions. If setting
a VLAN or multicast filter fails due to lack of sufficient
hardware resources, these packets get dropped. Fix this by
switching to VLAN or multicast promiscous mode so that these
packets are not dropped.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dsp_spl_jiffies need to be the same datatype as jiffies (which is ulong).
If not, on 64 bit systems it will fallback to schedule the DSP every jiffie
tic as soon jiffies become > 2^32.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Fixed hardware bridging/conference check routine of mISDN_dsp.ko.
In some cases the hardware bridging/conference (2-n parties) was selected,
but still pure software bridging/conference was used.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
mISDN: Fix NULL pointer bug in if-condition of mISDN_dsp
Fix a bug (was introduced by a cut & paste error)
in cases when dsp->conf was NULL.
Signed-off-by: Andreas Eversberg <jolly@eversberg.eu> Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Fri, 20 Apr 2012 09:49:23 +0000 (09:49 +0000)]
net: dcb: add CEE notify calls
This adds code to trigger CEE events when an APP change or setall
command is made from user space. This simplifies user space code
significantly by creating a single interface to listen on that
works with both firmware and userland agents.
And if we end up with multiple agents this keeps every thing in
sync userland agents, firmware agents, and kernel notifier consumers.
For an example agent that listens for these events see:
https://github.com/jrfastab/cgdcbxd
cgdcbxd is a daemon used to monitor DCB netlink events and manage
the net_prio control group sub-system.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Shmulik Ravid <shmulikr@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adds hepler to clean sdata ieee80211_clean_sdata similar way as
ieee80211_setup_sdata is implemented. The function will be used by other
interfaces later.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 23 Apr 2012 17:49:03 +0000 (19:49 +0200)]
mac80211: fix num_mcast_sta counting issues
Moving a STA to an AP VLAN prevents num_mcast_sta from being decremented
once the STA leaves, because sta->sdata changes. Fix this by checking
for AP VLANs as well.
Also exclude 4-addr VLAN stations from num_mcast_sta - remote 4-addr
stations ignore 3-address multicast frames anyway. In a typical bridge
configuration they receive the same packets as 4-address unicast.
This patch also fixes clearing the sdata->u.vlan.sta pointer when the
STA is removed from a 4-addr VLAN.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 23 Apr 2012 17:49:02 +0000 (19:49 +0200)]
mac80211: rename AP variable num_sta_authorized to num_mcast_sta
It is only used to test for BSS multicast receivers.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paul Gortmaker [Mon, 23 Apr 2012 04:49:13 +0000 (04:49 +0000)]
tipc: remove inline instances from C source files.
Untie gcc's hands and let it do what it wants within the
individual source files. There are two files, node.c and
port.c -- only the latter effectively changes (gcc-4.5.2).
Objdump shows gcc deciding to not inline port_peernode().
Suggested-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 23 Apr 2012 17:34:36 +0000 (17:34 +0000)]
tcp: tcp_try_coalesce returns a boolean
This clarifies code intention, as suggested by David.
Suggested-by: David Miller <davem@davemloft.net> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix merge between commit 3adadc08cc1e ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d27 ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 22 Apr 2012 12:26:16 +0000 (12:26 +0000)]
net: speedup skb_splice_bits()
Commit 35f3d14db (pipe: add support for shrinking and growing pipes)
added a slowdown for splice(socket -> pipe), as we might grow the spd
used in skb_splice_bits() for each skb we process in splice() syscall.
Its not needed since skb lengths are capped. The default on-stack arrays
are more than enough.
Use MAX_SKB_FRAGS instead of PIPE_DEF_BUFFERS to describe the reasonable
limit per skb.
Add coalescing support to help splicing of GRO skbs built from linear
skbs (linked into frag_list)
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull build system failure fix from Michal Marek:
"This fixes build failure with newer gcc that adds some internal
symbols that end in "__mod_*_device_table", but are not actually the
tables themselves."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Fix modpost failures in fedora 17
Eric Dumazet [Mon, 23 Apr 2012 07:11:42 +0000 (07:11 +0000)]
tcp: introduce tcp_try_coalesce
commit c8628155ece3 (tcp: reduce out_of_order memory use) took care of
coalescing tcp segments provided by legacy devices (linear skbs)
We extend this idea to fragged skbs, as their truesize can be heavy.
ixgbe for example uses 256+1024+PAGE_SIZE/2 = 3328 bytes per segment.
Use this coalescing strategy for receive queue too.
This contributes to reduce number of tcp collapses, at minimal cost, and
reduces memory overhead and packets drops.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch adds afex multifunction support to the driver (afex
multifunction is based on vntag header) and updates FW version used to 7.2.51.
Support includes the following:
1. Configure vif parameters in firmware (default vlan, vif id, default
priority, allowed priorities) according to values received from NIC.
2. Configure FW to strip/add default vlan according to afex vlan mode.
3. Notify link up to OS only after vif is fully initialized.
4. Support vif list set/get requests and configure FW accordingly.
5. Supply afex statistics upon request from NIC.
6. Special handling to L2 interface in case of FCoE vif.
Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Moving to interrupts instead of polling fpr TX completions
Avoiding situations where skb can be held in by the driver for
a long time (till timer expires).
The change is also necessary for supporting BQL.
Removing comp_lock that was required because we could handle TX
completions from several contexts: Interrupts, timer, polling.
Now there is only interrupts
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 22 Apr 2012 23:38:54 +0000 (23:38 +0000)]
tcp: sk_add_backlog() is too agressive for TCP
While investigating TCP performance problems on 10Gb+ links, we found a
tcp sender was dropping lot of incoming ACKS because of sk_rcvbuf limit
in sk_add_backlog(), especially if receiver doesnt use GRO/LRO and sends
one ACK every two MSS segments.
A sender usually tweaks sk_sndbuf, but sk_rcvbuf stays at its default
value (87380), allowing a too small backlog.
A TCP ACK, even being small, can consume nearly same truesize space than
outgoing packets. Using sk_rcvbuf + sk_sndbuf as a limit makes sense and
is fast to compute.
Performance results on netperf, single flow, receiver with disabled
GRO/LRO : 7500 Mbits instead of 6050 Mbits, no more TCPBacklogDrop
increments at sender.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Cc: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 22 Apr 2012 23:34:26 +0000 (23:34 +0000)]
net: add a limit parameter to sk_add_backlog()
sk_add_backlog() & sk_rcvqueues_full() hard coded sk_rcvbuf as the
memory limit. We need to make this limit a parameter for TCP use.
No functional change expected in this patch, all callers still using the
old sk_rcvbuf limit.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Cc: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net ax25: Fix the build when sysctl support is disabled.
Randy Dunlap <rdunlap@xenotime.net> reported:
> On 04/23/2012 12:07 AM, Stephen Rothwell wrote:
>
>> Hi all,
>>
>> Changes since 20120420:
>
>
> include/net/ax25.h:447:75: error: expected ';' before '}' token
>
> static inline int ax25_register_dev_sysctl(ax25_dev *ax25_dev) { return 0 };
> static inline void ax25_unregister_dev_sysctl(ax25_dev *ax25_dev) {};
>
> First function: move ';' inside braces.
> Second function: drop the ';'.
Put the semicolons where it makes sense.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'md-3.4-fixes' of git://neil.brown.name/md
Pull a few more md bug fixes from NeilBrown:
"2 are tagged for -stable, one being for a fairly serious bug that can
corrupt metadata and make it hard to recovery an array. The other is
for a more recent regression since 3.3"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md: fix possible corruption of array metadata on shutdown.
md: don't call ->add_disk unless there is good reason.
DM RAID: Use safe version of rdev_for_each
mm: fix s390 BUG by __set_page_dirty_no_writeback on swap
Mel reports a BUG_ON(slot == NULL) in radix_tree_tag_set() on s390
3.0.13: called from __set_page_dirty_nobuffers() when page_remove_rmap()
tries to transfer dirty flag from s390 storage key to struct page and
radix_tree.
That would be because of reclaim's shrink_page_list() calling
add_to_swap() on this page at the same time: first PageSwapCache is set
(causing page_mapping(page) to appear as &swapper_space), then
page->private set, then tree_lock taken, then page inserted into
radix_tree - so there's an interval before taking the lock when the
radix_tree slot is empty.
We could fix this by moving __add_to_swap_cache()'s spin_lock_irq up
before the SetPageSwapCache. But a better fix is simply to do what's
five years overdue: Ken Chen introduced __set_page_dirty_no_writeback()
(if !PageDirty TestSetPageDirty) for tmpfs to skip all the radix_tree
overhead, and swap is just the same - it ignores the radix_tree tag, and
does not participate in dirty page accounting, so should be using
__set_page_dirty_no_writeback() too.
s390 testing now confirms that this does indeed fix the problem.
Reported-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Ken Chen <kenchen@google.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
removed the possibility of a 'BUG' when data is written to an array
that has just been switched to read-only, but also introduced the
possibility that the array metadata could be corrupted.
If, when md_notify_reboot gets the mddev lock, the array is
in a state where it is assembled but hasn't been started (as can
happen if the personality module is not available, or in other unusual
situations), then incorrect metadata will be written out making it
impossible to re-assemble the array.
So only call __md_stop_writes() if the array has actually been
activated.
This patch is needed for any stable kernel which has had the above
commit applied.
Cc: stable@vger.kernel.org Reported-by: Christoph Nelles <evilazrael@evilazrael.de> Signed-off-by: NeilBrown <neilb@suse.de>
md/raid5: If there is a spare and a want_replacement device, start replacement.
cause md_check_recovery to call ->add_disk much more often.
Instead of only when the array is degraded, it is now called whenever
md_check_recovery finds anything useful to do, which includes
updating the metadata for clean<->dirty transition.
This causes unnecessary work, and causes info messages from ->add_disk
to be reported much too often.
So refine md_check_recovery to only do any actual recovery checking
(including ->add_disk) if MD_RECOVERY_NEEDED is set.
This fix is suitable for 3.3.y:
Cc: stable@vger.kernel.org Reported-by: Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by: NeilBrown <neilb@suse.de>
net sysctl: Add place holder functions for when sysctl support is compiled out of the kernel.
Randy Dunlap <rdunlap@xenotime.net> reported:
> On 04/23/2012 12:07 AM, Stephen Rothwell wrote:
>
>> Hi all,
>>
>> Changes since 20120420:
>
>
>
> ERROR: "unregister_net_sysctl_table" [net/phonet/phonet.ko] undefined!
> ERROR: "register_net_sysctl" [net/phonet/phonet.ko] undefined!
>
> when CONFIG_SYSCTL is not enabled.
Add static inline stub functions to gracefully handle the case when sysctl
support is not present.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 17 Apr 2012 14:36:30 +0000 (07:36 -0700)]
iwlwifi: clean up module parameters
For now at least, all module parameters should be
with the core functionality, so move them there,
while at it rename to iwlwifi_mod_params. Also
rename iwl-shared.h to iwl-modparams.h to reflect
the real contents.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Don Fry [Fri, 23 Mar 2012 22:41:07 +0000 (15:41 -0700)]
iwlwifi: revert workaround to restore 1000 rx throughput
A workaround in commit c0486b7ccc5 resulted in a 40% drop in receive
throughput in order to fix a transmit problem. The transmit problem
no longer occurs, so restore the receive throughput.
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Thu, 12 Apr 2012 13:24:30 +0000 (06:24 -0700)]
iwlwifi: use direct calls for transport free
Since the transport allocates and frees itself in
the transport specific code, there's no need for
virtual functions for it. Remove the free method
and call the correct functions directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Tue, 3 Apr 2012 18:41:07 +0000 (20:41 +0200)]
iwlwifi: move eeprom versions to HW files
The hardware files belong to the core PCI
functionality, but the eeprom header file
mixes higher-level functionality and the
defines, so move out the specific defines
and put them into the appropriate HW files
instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We only need one declaration, not multiple.
Keep the one in iwl-shared.h, which will
probably be renamed to iwl-modparams.h at
some point in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Mon, 23 Apr 2012 21:25:51 +0000 (14:25 -0700)]
iwlwifi: remove TX/RX frame statistics
Keeping statistics per frame type really isn't
very useful, and needs a huge amount of code
so remove it. Since that is the only thing in
iwl-core.{c,h} now, those files can be killed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>