Mengdong Lin [Thu, 23 Aug 2012 09:32:30 +0000 (17:32 +0800)]
ALSA: hda - add runtime PM support
Runtime PM can bring more power saving:
- When the controller is suspended, its parent device will also have a chance
to suspend.
- PCI subsystem can choose the lowest power state the controller can signal
wake up from. This state can be D3cold on platforms with ACPI PM support.
And runtime PM can provide a gerneral sysfs interface for a system policy
manager.
Runtime PM support is based on current HDA power saving implementation. The user
can enable runtime PM on platfroms that provide acceptable latency on transition
from D3 to D0.
Details:
- When both power saving and runtime PM are enabled:
-- If a codec supports 'stop-clock' in D3, it will request suspending the
controller after it enters D3 and request resuming the controller before
back to D0. Thus the controller will be suspended only when all codecs are
suspended and support stop-clock in D3.
-- User IO operations and HW wakeup signal can resume the controller back to
D0.
- If runtime PM is disabled, power saving just works as before.
- If power saving is disabled, the controller won't be suspended because the
power usage counter can never be 0.
More about 'stop-clock' feature:
If a codec can support targeted pass-through operations in D3 state when there
is no BCLK present on the link, it will set CLKSTOP flag in the supported power
states and report PS-ClkStopOk when entering D3 state. Please refer to HDA spec
section 7.3.3.10 Power state and 7.3.4.12 Supported Power State.
[Fixed CONFIG_PM_RUNTIME dependency in hda_intel.c by tiwai]
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 22 Aug 2012 14:40:24 +0000 (16:40 +0200)]
ALSA: hda - Call snd_hda_jack_report_sync() generically in hda_codec.c
Instead of calling the jack sync in the init callback of each codec,
call it generically at initialization and resume. By calling it at
the last of resume sequence, a possible race between the jack sync and
the unsol event enablement in the current code will be closed, too.
Introduce snd-cmi8328 driver for C-Media CMI8328-based sound cards, such as
AudioExcel AV500.
It supports PCM playback and capture (full-duplex) through wss_lib, gameport,
OPL3 and MPU401. The AV500 card has onboard Dream wavetable synth connected
to the MPU401 port and Aux 1 input internally which works too.
The CDROM interface is not supported (as the drivers for these CDROMs were
removed from the kernel some time ago).
A separate driver is needed because CMI8328 is completely different chip to
CMI8329/CMI8330. It's configured by magic registers (there's no PnP). Sound is
provided by a real WSS codec (CS4231A) and the SB part is just a SB Pro
emulation (for DOS games, useless for Linux).
When SB is enabled, the CMI8328 chip disables access to the WSS codec,
emulates SoundBlaster on one side and outputs sound data to the codec - so SB
and WSS can't work together with this card. The WSS codec can do full duplex
by itself so there's no need for crazy things like snd-cmi8330 does
(combining SB and WSS parts into one driver).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 20 Aug 2012 19:25:22 +0000 (21:25 +0200)]
ALSA: hda - Fix leftover codec->power_transition
When the codec turn-on operation is canceled by the immediate
power-on, the driver left the power_transition flag as is.
This caused the persistent avoidance of power-save behavior.
Takashi Iwai [Mon, 20 Aug 2012 19:26:04 +0000 (21:26 +0200)]
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Additional updates for 3.6
A batch more bugfixes, all driver-specific and fairly small and
unremarkable in a global context. The biggest batch are for the newly
added Arizona drivers.
Andi Kleen [Sun, 19 Aug 2012 02:56:22 +0000 (19:56 -0700)]
ALSA: lto, sound: Fix export symbols for !CONFIG_MODULES
The new LTO EXPORT_SYMBOL references symbols even without CONFIG_MODULES.
Since these functions are macros in this case this doesn't work.
Add a ifdef to fix the build.
Takashi Iwai [Tue, 14 Aug 2012 15:13:32 +0000 (17:13 +0200)]
ALSA: hda - Check the power state when power_save option is changed
... by calling the newly introduced snd_hda_power_sync().
I had to reimplement a wheel for adding the trigger at changing the
parameter -- the parameter set ops is overwritten to pass the integer
parameter, then trigger the power-state sync.
Takashi Iwai [Tue, 14 Aug 2012 15:12:47 +0000 (17:12 +0200)]
ALSA: hda - Implement snd_hda_power_sync() helper function
Added a new helper function snd_hda_power_sync() to trigger the
power-saving manually. It's an inline function call to
snd_hda_power_save() helper function.
Together with this addition, snd_hda_power_up*() and
snd_hda_power_down() functions are inlined to a call of the same
snd_hda_power_save() helper function.
ALSA: hda - don't create dysfunctional mixer controls for ca0132
It's possible that these amps are settable somehow, e g through
secret codec verbs, but for now, don't create the controls (as
they won't be working anyway, and cause errors in amixer).
struct snd_card_ad1816a is only set but the values are never used then.
Removing it allows struct snd_card's private_data to be used for
struct snd_ad1816a, simplifying the code.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Carpenter [Sat, 18 Aug 2012 15:55:15 +0000 (18:55 +0300)]
sound: oss/sb_audio: prevent divide by zero bug
Speed comes from get_user() in audio_ioctl(). We use it to set the "s"
variable before clamping it to valid values so it could lead to a divide
by zero bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown [Thu, 16 Aug 2012 21:36:04 +0000 (22:36 +0100)]
ASoC: wm9712: Fix microphone source selection
Currently the microphone input source is not selectable as while there is
a DAPM widget it's not connected to anything so it won't be properly
instantiated. Add something more correct for the input structure to get
things going, even though it's not hooked into the rest of the routing
map and so won't actually achieve anything except allowing the relevant
register bits to be written.
Reported-by: Christop Fritz <chf.fritz@googlemail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org
Takashi Iwai [Wed, 15 Aug 2012 10:32:00 +0000 (12:32 +0200)]
ALSA: usb-audio: Fix scheduling-while-atomic bug in PCM capture stream
A PCM capture stream on usb-audio causes a scheduling-while-atomic
BUG, as reported in the bugzilla entry below. It's because
snd_usb_endpoint_start() is called at first at trigger START for a
capture stream, and this function contains the left-over EP
deactivation codes. The problem doesn't happen for a playback stream
because the function is called at PCM prepare time, which can sleep.
This patch fixes the BUG by moving the EP deactivation code into the
PCM prepare callback.
Takashi Iwai [Mon, 13 Aug 2012 09:09:35 +0000 (11:09 +0200)]
ALSA: hda - Add 3stack-automute model to AD1882 codec
Added a simple support of automute for the front HP jack to AD1882
stack model. Such an addition is basically an exception -- we really
want to avoid the static quirk codes, but AD1882 parser isn't still
ready for moving to the BIOS auto-parser yet. So, as a quick fix, I
merged it for now.
In near future, we really need the big clean up of patch_analog.c to
move on to the auto-parser...
Takashi Iwai [Tue, 14 Aug 2012 16:10:09 +0000 (18:10 +0200)]
ALSA: hda - Fix possible compile warnings regarding CONFIG_PM
Replace with a proper ifdef check of CONFIG_PM_SLEEP in hda_intel.c.
But other places in HD-audio driver are still marked with CONFIG_PM,
since these can be called for power-saving even without
CONFIG_PM_SLEEP.
Sachin Kamat [Wed, 8 Aug 2012 06:04:43 +0000 (11:34 +0530)]
ASoC: Samsung: Fix build error
Fixes the following build error:
In file included from arch/arm/mach-exynos/include/mach/dma.h:24:0,
from arch/arm/plat-samsung/include/plat/dma-ops.h:17,
from arch/arm/plat-samsung/include/plat/dma.h:128,
from sound/soc/samsung/pcm.c:23:
arch/arm/plat-samsung/include/plat/dma-pl330.h:106:8:
error: redefinition of ‘struct s3c2410_dma_client’
arch/arm/plat-samsung/include/plat/dma.h:40:8: note: originally defined here
make[3]: *** [sound/soc/samsung/pcm.o] Error 1
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mengdong Lin [Fri, 10 Aug 2012 12:11:58 +0000 (14:11 +0200)]
ALSA : hda - bug fix on checking the supported power states of a codec
The return value of snd_hda_param_read() is -1 for an error, otherwise
it's the supported power states of a codec.
The supported power states is a 32-bit value. Bit 31 will be set to 1
if the codec supports EPSS, thus making "sup" negative. And the bit
28:5 is reserved as "0".
So a negative value other than -1 shall be further checked.
Please refer to High-Definition spec 7.3.4.12 "Supported Power
States", thanks!
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
When "Beep Playback Switch" had a different value on left and right
channels (such as muting left but not right, or vice versa), this
could result in the right channel being ignored.
This patch enables beep to be sounding from right channel only, and
also give correct result back to userspace (e g amixer).
Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown [Thu, 9 Aug 2012 17:44:37 +0000 (18:44 +0100)]
ASoC: core: Upgrade the severity of probe deferral errors to dev_err()
In the past when ASoC had a custom probe deferral mechanism people
complained about the logspam it generated and didn't want to know about
the fact that we were doing probe deferral so all the error messages for
it were at dev_dbg(), making diagnostics hard. Now that we have probe
deferral as an accepted thing and it's generating log messages anyway
there's no need to worry about this so upgrade the severity of all the
probe deferral sources to dev_err() so that they are displayed by default.
Also add one for missing aux_devs since there wasn't one.
Reported-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai [Thu, 9 Aug 2012 14:30:13 +0000 (16:30 +0200)]
Merge branch 'topic/hda-probe-defer' into for-next
This branch fixes the stall during probing the HD-audio driver when
the specified "patch" firmware doesn't exist. It's basically a long-
standing issue, but mostly harmless until the recent rework of
firmware loader base code.
Takashi Iwai [Thu, 9 Aug 2012 11:49:23 +0000 (13:49 +0200)]
ALSA: hda - Deferred probing with request_firmware_nowait()
For processing the firmware handling properly for built-in kernels,
implement an asynchronous firmware loading with
request_firmware_nowait(). This means that the codec probing is
deferred when the patch option is specified.
Takashi Iwai [Wed, 8 Aug 2012 15:12:52 +0000 (17:12 +0200)]
ALSA: hda - Add codec->pcm_format_first flag
Introduced a new flag to set up the PCM stream format at first before
the stream_id and channel tag. Some codecs (e.g. CA0132) seem
preferring this over stream_id -> format order.
Peter Ujfalusi [Tue, 7 Aug 2012 12:37:47 +0000 (15:37 +0300)]
ASoC: omap-mcbsp: Fix 6pin mux configuration
The check for the mux_signal callback was wrong which prevents us to
configure the 6pin port's FSR/CLKR signal mux.
Reported-by: CF Adad <cfadad@rocketmail.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org (3.4+)
Takashi Iwai [Mon, 6 Aug 2012 12:49:36 +0000 (14:49 +0200)]
ALSA: hda - Fix regression of HDMI codec probing
The commit c4bfe94a causes a regression on some codecs at probing.
Since this was just a workaround to shut up a kernel warning, it'd be
better to revert and fix properly. So we ended up with re-adding the
cleanup callback.
Tested-and-reported-by: Matt Horan <matt@matthoran.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown [Fri, 3 Aug 2012 22:01:54 +0000 (23:01 +0100)]
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-3.6
ASoC: Additional updates for 3.6
A few updates for issues discovered during the merge window, the main
one being the fix for the issues with defaulting to use of regmap
without properly checking if there was I/O in place already.
Takashi Iwai [Fri, 3 Aug 2012 10:51:21 +0000 (12:51 +0200)]
ALSA: emu10k1: Avoid access to invalid pages when period=1
When period=1, the driver tries to allocate a bit bigger buffer than
requested by the user due to the irq latency tolerance. This may lead
to accesses over the actually allocated pages.
This patch adds a check of the page index and assigns the silent page
when it's over the given buffer size.
Linus Torvalds [Thu, 2 Aug 2012 18:52:39 +0000 (11:52 -0700)]
Merge branch 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc
Pull OLPC platform updates from Andres Salomon:
"These move the OLPC Embedded Controller driver out of
arch/x86/platform and into drivers/platform/olpc.
OLPC machines are now ARM-based (which means lots of x86 and ARM
changes), but are typically pretty self-contained.. so it makes more
sense to go through a separate OLPC tree after getting the appropriate
review/ACKs."
* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
x86: OLPC: move s/r-related EC cmds to EC driver
Platform: OLPC: move global variables into priv struct
Platform: OLPC: move debugfs support from x86 EC driver
x86: OLPC: switch over to using new EC driver on x86
Platform: OLPC: add a suspended flag to the EC driver
Platform: OLPC: turn EC driver into a platform_driver
Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
drivers: OLPC: update various drivers to include olpc-ec.h
Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver
Linus Torvalds [Thu, 2 Aug 2012 18:50:24 +0000 (11:50 -0700)]
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
"This contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the
branch into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: Kirkwood: Replace mrvl with marvell
ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
ARM: Kirkwood: Describe Dreamplug LEDs in DT.
ARM: Kirkwood: Describe iConnects LEDs in DT.
ARM: Kirkwood: Describe iConnects temperature sensor in DT.
ARM: Kirkwood: Describe IB62x0 LEDs in DT.
ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
ARM: Kirkwood: Use DT to configure SATA device.
ARM: kirkwood: use devicetree for SPI on dreamplug
ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
ARM: Kirkwood: Add basic device tree support for QNAP TS219.
ATA: sata_mv: Add device tree support
ARM: Orion: DTify the watchdog timer.
ARM: Orion: Add arch support needed for I2C via DT.
ARM: kirkwood: use devicetree for orion-spi
...
Linus Torvalds [Thu, 2 Aug 2012 18:48:54 +0000 (11:48 -0700)]
Merge tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
"Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
but didn't go in because the pull request ended up rejected. So it
just got merged, and we got this staged branch that enables the
coupled cpuidle code on OMAP.
With a stable git workflow from the other maintainer we could have
staged this earlier, but that wasn't the case so we have had to merge
it late.
The alternative is to hold it off until 3.7 but given that the code is
well-isolated to OMAP and they are eager to see it go in, I didn't
push back hard in that direction."
* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP4: CPUidle: Open broadcast clock-event device.
ARM: OMAP4: CPUidle: add synchronization for coupled idle states
ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus
Linus Torvalds [Thu, 2 Aug 2012 18:48:20 +0000 (11:48 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for merge window fallout, and a bugfix for timer resume on
PRIMA2."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mmp: add missing irqs.h
arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
ARM: mxc: Include missing irqs.h header
Linus Torvalds [Thu, 2 Aug 2012 18:45:42 +0000 (11:45 -0700)]
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
sh: explicitly include sh_dma.h in setup-sh7722.c
sh: ecovec: care CN5 VBUS if USB host mode
sh: sh7724: fixup renesas_usbhs clock settings
sh: intc: initial irqdomain support.
sh: pfc: Fix up init ordering mess.
serial: sh-sci: fix compilation breakage, when DMA is enabled
dmaengine: shdma: restore partial transfer calculation
sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
sh: Fix up recursive fault in oops with unset TTB.
sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
sh: select the fixed regulator driver on several boards
sh: ecovec: switch MMC power control to regulators
sh: add fixed voltage regulators to se7724
sh: add fixed voltage regulators to sdk7786
sh: add fixed voltage regulators to rsk
sh: add fixed voltage regulators to migor
sh: add fixed voltage regulators to kfr2r09
sh: add fixed voltage regulators to ap325rxa
sh: add fixed voltage regulators to sh7757lcr
sh: add fixed voltage regulators to sh2007
...
Linus Torvalds [Thu, 2 Aug 2012 18:34:40 +0000 (11:34 -0700)]
Merge tag 'md-3.6' of git://neil.brown.name/md
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
Linus Torvalds [Thu, 2 Aug 2012 17:57:31 +0000 (10:57 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull two ceph fixes from Sage Weil:
"The first patch fixes up the old crufty open intent code to use the
atomic_open stuff properly, and the second fixes a possible null deref
and memory leak with the crypto keys."
Linus Torvalds [Thu, 2 Aug 2012 17:56:34 +0000 (10:56 -0700)]
Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
- Fixes a bug when the lower filesystem mount options include 'acl',
but the eCryptfs mount options do not
- Cleanups in the messaging code
- Better handling of empty files in the lower filesystem to improve
usability. Failed file creations are now cleaned up and empty lower
files are converted into eCryptfs during open().
- The write-through cache changes are being reverted due to bugs that
are not easy to fix. Stability outweighs the performance
enhancements here.
- Improvement to the mount code to catch unsupported ciphers specified
in the mount options
* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: check for eCryptfs cipher support at mount
eCryptfs: Revert to a writethrough cache model
eCryptfs: Initialize empty lower files when opening them
eCryptfs: Unlink lower inode when ecryptfs_create() fails
eCryptfs: Make all miscdev functions use daemon ptr in file private_data
eCryptfs: Remove unused messaging declarations and function
eCryptfs: Copy up POSIX ACL and read-only flags from lower mount
Linus Torvalds [Thu, 2 Aug 2012 17:54:11 +0000 (10:54 -0700)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS update from Steve French:
"Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.
I am holding up a few more days on merging the remainder of the
SMB2/SMB2.1 enablement although it is nearing review completion, in
order to address some review comments from Jeff Layton on a few of the
subsequent SMB2 patches, and also to debug an unrelated cifs problem
that Pavel discovered."
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Add SMB2 support for rmdir
CIFS: Move rmdir code to ops struct
CIFS: Add SMB2 support for mkdir operation
CIFS: Separate protocol specific part from mkdir
CIFS: Simplify cifs_mkdir call
Linus Torvalds [Thu, 2 Aug 2012 17:37:03 +0000 (10:37 -0700)]
mm: remove node_start_pfn checking in new WARN_ON for now
Borislav Petkov reports that the new warning added in commit 88fdf75d1bb5 ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.
and (with the warning replaced by debug output), Borislav sees
On node 0 totalpages: 4193848
DMA zone: 64 pages used for memmap
DMA zone: 6 pages reserved
DMA zone: 3890 pages, LIFO batch:0
DMA32 zone: 16320 pages used for memmap
DMA32 zone: 798464 pages, LIFO batch:31
Normal zone: 52736 pages used for memmap
Normal zone: 3322368 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 4423680 <----
On node 1 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 8617984 <----
On node 2 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 12812288 <----
On node 3 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
so remove the bogus warning for now to avoid annoying people. Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Barry Song [Mon, 30 Jul 2012 05:29:30 +0000 (13:29 +0800)]
ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
The only way to write LATCHED registers to write LATCH_BIT to LATCH register,
that will latch COUNTER into LATCHED.e.g.
writel_relaxed(SIRFSOC_TIMER_LATCH_BIT, sirfsoc_timer_base +
SIRFSOC_TIMER_LATCH);
Writing values to LATCHED registers directly is useless at all.
Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Takashi Iwai [Thu, 2 Aug 2012 16:11:25 +0000 (18:11 +0200)]
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Additional updates for 3.6
A few updates for issues discovered during the merge window, the main
one being the fix for the issues with defaulting to use of regmap
without properly checking if there was I/O in place already.
Sage Weil [Tue, 31 Jul 2012 18:27:36 +0000 (11:27 -0700)]
ceph: simplify+fix atomic_open
The initial ->atomic_open op was carried over from the old intent code,
which was incomplete and didn't really work. Replace it with a fresh
method. In particular:
* always attempt to do an atomic open+lookup, both for the create case
and for lookups of existing files.
* fix symlink handling by returning 1 to the VFS so that we can follow
the link to its destination. This fixes a longstanding ceph bug (#2392).
Mark Brown [Wed, 1 Aug 2012 19:05:47 +0000 (20:05 +0100)]
ASoC: core: Fix check before defaulting to regmap
Check if the chip has provided a write operation (which is mandatory for
I/O) rather than looking for control data as some of the MFDs use a global
for this. Also skip the attempt if there's no regmap available by device
in case things get confused by the attempt to default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Takashi Iwai [Thu, 2 Aug 2012 07:04:39 +0000 (09:04 +0200)]
ALSA: hda - Support dock on Lenovo Thinkpad T530 with ALC269VC
Lenovo Thinkpad T530 with ALC269VC codec has a dock port but BIOS
doesn't set up the pins properly. Enable the pins as well as on
Thinkpad X230 Tablet.
Reported-and-tested-by: Mario <anyc@hadiko.de> Cc: <stable@vger.kernel.org> [v3.2+] Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Wed, 1 Aug 2012 23:47:15 +0000 (16:47 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"The lion share of this pull request are fixes for clk-related breakage
caused by other changes during this merge window. For some platforms
the fix was as simple as selecting HAVE_CLK, for others like the
Loongson 2 significant restructuring was required.
The remainder are changes required to get the Lantiq code to work
again."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Loongson 2: Sort out clock managment.
MIPS: Loongson 1: more clk support and add select HAVE_CLK
MIPS: txx9: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: BCM63xx: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: AR7: Fix redefinition of clk_* by adding select HAVE_CLK
MIPS: Lantiq: Platform specific CLK fixup
MIPS: Lantiq: Add device_tree_init function
MIPS: Lantiq: Fix interface clock and PCI control register offset
Linus Torvalds [Wed, 1 Aug 2012 23:45:02 +0000 (16:45 -0700)]
Merge branch 'for-linus-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML fixes from Richard Weinberger:
"This patch set contains mostly fixes and cleanups. The UML tty driver
uses now tty_port and is no longer broken like hell :-)"
* 'for-linus-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Add arch/x86/um to MAINTAINERS
um: pass siginfo to guest process
um: fix ubd_file_size for read-only files
um: pull interrupt_end() into userspace()
um: split syscall_trace(), pass pt_regs to it
um: switch UPT_SET_RETURN_VALUE and regs_return_value to pt_regs
um: set BLK_CGROUP=y in defconfig
um: remove count_lock
um: fully use tty_port
um: Remove dead code
um: remove line_ioctl()
TTY: um/line, use tty from tty_port
TTY: um/line, add tty_port
Linus Torvalds [Wed, 1 Aug 2012 23:41:07 +0000 (16:41 -0700)]
Merge branch 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
Linus Torvalds [Wed, 1 Aug 2012 23:35:37 +0000 (16:35 -0700)]
Merge branch 'audit' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM audit/signal updates from Russell King:
"ARM audit/signal handling updates from Al and Will. This improves on
the work Viro did last merge window, and sorts out some of the issues
found with that work."
* 'audit' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7475/1: sys_trace: allow all syscall arguments to be updated via ptrace
ARM: 7474/1: get rid of TIF_SYSCALL_RESTARTSYS
ARM: 7473/1: deal with handlerless restarts without leaving the kernel
ARM: 7472/1: pull all work_pending logics into C function
ARM: 7471/1: Revert "7442/1: Revert "remove unused restart trampoline""
ARM: 7470/1: Revert "7443/1: Revert "new way of handling ERESTART_RESTARTBLOCK""