Daniel Drake [Mon, 30 Apr 2012 21:06:27 +0000 (18:06 -0300)]
[media] via-camera: specify XO-1.5 camera clock speed
For the ov7670 camera to return images at the requested frame rate,
it needs to make calculations based on the clock speed, which is
a completely external factor (depends on the wiring of the system).
On the XO-1.5, which is the only known via-camera user, the camera
is clocked at 90MHz.
Pass this information to the ov7670 driver, to fix an issue where
a framerate of 3x the requested amount was being provided.
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That commit message suggests that by not taking the core lock for fops
other than unlocked_ioctl all problems relating to AB-BA locking and
mm->mmap_sem are solved. This is not the case.
More work needs to be done by moving the core lock further down into
video_ioctl2. It should only be taken after the copy_from/to_user calls
are done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 6 May 2012 16:31:27 +0000 (13:31 -0300)]
[media] av7110: fix v4l2_compliance test issues
Besides the usual inconsistencies in input enumeration there was also a
kernel crash if you tried to poll on a vbi node. The checks for sliced
vbi output vs vbi capture were not complete enough.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The B&W control never worked, and you get the same effect by setting saturation to the
lowest value. So it has been removed. Also fixed some incorrect entries in the input
table. This driver now passes v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 1 May 2012 13:06:40 +0000 (10:06 -0300)]
[media] tda9840: fix setting of the audio mode
You have to first detect the current rxsubchans (mono, stereo or bilingual),
and depending on that you can set the audio mode. It does not automatically
switch when the audio channels change.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 14 May 2012 13:22:58 +0000 (10:22 -0300)]
[media] v4l/dvb: fix compiler warnings
media_build/v4l/drxk_hard.c: In function 'DownloadMicrocode':
media_build/v4l/drxk_hard.c:1388:6: warning: variable 'BlockCRC' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1384:6: warning: variable 'Drain' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1383:6: warning: variable 'Flags' set but not used [-Wunused-but-set-variable]
media_build/v4l/lmedm04.c: In function 'lme2510_probe':
media_build/v4l/lmedm04.c:1208:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hopper_cards.c: In function 'hopper_irq_handler':
media_build/v4l/hopper_cards.c:68:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_cards.c: In function 'mantis_irq_handler':
media_build/v4l/mantis_cards.c:76:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c: In function 'mantis_dma_stop':
media_build/v4l/mantis_dma.c:202:16: warning: variable 'mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c:202:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_evm.c: In function 'mantis_hifevm_work':
media_build/v4l/mantis_evm.c:44:17: warning: variable 'gpif_mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_init_calc':
media_build/v4l/stb0899_drv.c:640:5: warning: variable 'agc1cn' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_diseqc_init':
media_build/v4l/stb0899_drv.c:830:13: warning: variable 'f22_rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c:826:31: warning: variable 'tx_data' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv0900_sw.c: In function 'stv0900_track_optimization':
media_build/v4l/stv0900_sw.c:838:26: warning: variable 'rolloff' set but not used [-Wunused-but-set-variable]
media_build/v4l/ir-sanyo-decoder.c: In function 'ir_sanyo_decode':
media_build/v4l/ir-sanyo-decoder.c:59:14: warning: variable 'not_address' set but not used [-Wunused-but-set-variable]
media_build/v4l/mceusb.c: In function 'mceusb_dev_printdata':
media_build/v4l/mceusb.c:523:46: warning: variable 'data5' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 20 Apr 2012 11:04:48 +0000 (08:04 -0300)]
[media] v4l/dvb: fix compiler warnings
media_build/v4l/stb6100.c: In function 'stb6100_read_reg':
media_build/v4l/stb6100.c:161:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx24110.c: In function 'cx24110_read_ucblocks':
media_build/v4l/cx24110.c:515:6: warning: variable 'lastbyer' set but not used [-Wunused-but-set-variable]
media_build/v4l/dib9000.c: In function 'dib9000_mbx_process':
media_build/v4l/dib9000.c:711:6: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
media_build/v4l/zl10353.c: In function 'zl10353_init':
media_build/v4l/zl10353.c:562:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv0297.c: In function 'stv0297_set_frontend':
media_build/v4l/stv0297.c:417:16: warning: variable 'starttime' set but not used [-Wunused-but-set-variable]
media_build/v4l/lgs8gxx.c: In function 'lgs8gxx_set_mode_manual':
media_build/v4l/lgs8gxx.c:265:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/af9013.c: In function 'af9013_statistics_work':
media_build/v4l/af9013.c:517:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv090x.c: In function 'stv090x_optimize_track':
media_build/v4l/stv090x.c:2845:23: warning: variable 'rolloff' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv090x.c: In function 'stv090x_algo':
media_build/v4l/stv090x.c:3177:28: warning: variable 'no_signal' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_read_ber':
media_build/v4l/it913x-fe.c:636:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_get_frontend':
media_build/v4l/it913x-fe.c:661:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_set_frontend':
media_build/v4l/it913x-fe.c:694:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/m88rs2000.c: In function 'm88rs2000_set_fec':
media_build/v4l/m88rs2000.c:657:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dst_ca.c: In function 'ca_send_message':
media_build/v4l/dst_ca.c:480:15: warning: variable 'ca_message_header_len' set but not used [-Wunused-but-set-variable]
media_build/v4l/smssdio.c: In function 'smssdio_interrupt':
media_build/v4l/smssdio.c:117:11: warning: variable 'isr' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 20 Apr 2012 10:30:48 +0000 (07:30 -0300)]
[media] v4l: fix compiler warnings
media_build/v4l/adv7343.c: In function 'adv7343_setstd':
media_build/v4l/adv7343.c:133:6: warning: variable 'output_idx' set but not used [-Wunused-but-set-variable]
media_build/v4l/tvp5150.c: In function 'tvp5150_mbus_fmt':
media_build/v4l/tvp5150.c:833:14: warning: variable 'std' set but not used [-Wunused-but-set-variable]
media_build/v4l/tvp7002.c: In function 'tvp7002_query_dv_preset':
media_build/v4l/tvp7002.c:673:18: warning: variable 'device' set but not used [-Wunused-but-set-variable]
media_build/v4l/c-qcam.c: In function 'qc_capture':
media_build/v4l/c-qcam.c:381:33: warning: variable 'bitsperxfer' set but not used [-Wunused-but-set-variable]
media_build/v4l/pms.c: In function 'pms_s_std':
media_build/v4l/pms.c:738:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/pms.c: In function 'init_mediavision':
media_build/v4l/pms.c:959:6: warning: variable 'id' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-alsa.c: In function 'cx25821_irq':
media_build/v4l/cx25821-alsa.c:294:6: warning: variable 'audint_count' set but not used [-Wunused-but-set-variable]
media_build/v4l/zr364xx.c: In function 'zr364xx_fillbuff':
media_build/v4l/zr364xx.c:510:25: warning: variable 'frm' set but not used [-Wunused-but-set-variable]
media_build/v4l/s2255drv.c: In function 's2255_fillbuff':
media_build/v4l/s2255drv.c:637:23: warning: variable 'frm' set but not used [-Wunused-but-set-variable]
media_build/v4l/s2255drv.c: In function 'vidioc_s_fmt_vid_cap':
media_build/v4l/s2255drv.c:990:6: warning: variable 'norm' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-stds.c: In function 'tm6000_set_audio_std':
media_build/v4l/tm6000-stds.c:341:10: warning: variable 'nicam_flag' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-video.c: In function 'get_next_buf':
media_build/v4l/tm6000-video.c:172:8: warning: variable 'outp' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-video.c: In function 'copy_streams':
media_build/v4l/tm6000-video.c:214:36: warning: variable 'c' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-input.c: In function 'tm6000_ir_urb_received':
media_build/v4l/tm6000-input.c:171:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c: In function 'usbvision_decompress':
media_build/v4l/usbvision-core.c:604:23: warning: variable 'max_pos' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c: In function 'usbvision_parse_compress':
media_build/v4l/usbvision-core.c:705:39: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c:705:22: warning: variable 'bytes_per_pixel' set but not used [-Wunused-but-set-variable]
media_build/v4l/zoran_device.c: In function 'write_overlay_mask':
media_build/v4l/zoran_device.c:545:6: warning: variable 'reg' set but not used [-Wunused-but-set-variable]
media_build/v4l/go7007-v4l2.c: In function 'go7007_streamoff':
media_build/v4l/go7007-v4l2.c:79:6: warning: variable 'retval' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 14 May 2012 13:17:35 +0000 (10:17 -0300)]
[media] v4l: fix compiler warnings
media_build/v4l/au0828-video.c: In function 'au0828_irq_callback':
media_build/v4l/au0828-video.c:123:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx23888-ir.c: In function 'pulse_clocks_to_clock_divider':
media_build/v4l/cx23888-ir.c:334:6: warning: variable 'rem' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25840-ir.c: In function 'pulse_clocks_to_clock_divider':
media_build/v4l/cx25840-ir.c:319:6: warning: variable 'rem' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25840-ir.c: In function 'cx25840_ir_tx_write':
media_build/v4l/cx25840-ir.c:863:21: warning: variable 'c' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c: In function 'snd_em28xx_hw_capture_params':
media_build/v4l/em28xx-audio.c:346:31: warning: variable 'format' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c:346:25: warning: variable 'rate' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c:346:15: warning: variable 'channels' set but not used [-Wunused-but-set-variable]
media_build/v4l/hdpvr-control.c: In function 'get_input_lines_info':
media_build/v4l/hdpvr-control.c:98:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hdpvr-video.c: In function 'hdpvr_try_ctrl':
media_build/v4l/hdpvr-video.c:955:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/saa7134-video.c: In function 'saa7134_s_tuner':
media_build/v4l/saa7134-video.c:2030:6: warning: variable 'rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/sn9c102_core.c: In function 'sn9c102_stream_interrupt':
media_build/v4l/sn9c102_core.c:998:7: warning: variable 'timeout' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Janne Grunau <j@jannau.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 20 Apr 2012 09:26:19 +0000 (06:26 -0300)]
[media] cx25821: fix compiler warnings
media_build/v4l/cx25821-core.c: In function 'cx_i2c_read_print':
media_build/v4l/cx25821-core.c:386:6: warning: variable 'value' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-core.c: In function 'cx25821_dev_setup':
media_build/v4l/cx25821-core.c:899:6: warning: variable 'io_size' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-core.c: In function 'cx25821_irq':
media_build/v4l/cx25821-core.c:1321:18: warning: variable 'pci_mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-i2c.c: In function 'cx25821_i2c_read':
media_build/v4l/cx25821-i2c.c:365:6: warning: variable 'retval' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_enable_bluefield_output':
media_build/v4l/cx25821-medusa-video.c:39:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_set_resolution':
media_build/v4l/cx25821-medusa-video.c:435:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_set_decoderduration':
media_build/v4l/cx25821-medusa-video.c:498:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'cx25821_dump_video_queue':
media_build/v4l/cx25821-video.c:116:25: warning: variable 'buf' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'cx25821_buffer_prepare':
media_build/v4l/cx25821-video.c:561:20: warning: variable 'line1_offset' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'video_ioctl_set':
media_build/v4l/cx25821-video.c:1834:6: warning: variable 'value' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video-upstream.c: In function 'cx25821_upstream_irq':
media_build/v4l/cx25821-video-upstream.c:641:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video-upstream-ch2.c: In function 'cx25821_upstream_irq_ch2':
media_build/v4l/cx25821-video-upstream-ch2.c:591:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-audio-upstream.c: In function 'cx25821_upstream_irq_audio':
media_build/v4l/cx25821-audio-upstream.c:589:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 23 Apr 2012 11:25:20 +0000 (08:25 -0300)]
[media] ivtv/cx18: fix compiler warnings
media_build/v4l/cx18-alsa-main.c: In function 'cx18_alsa_exit':
media_build/v4l/cx18-alsa-main.c:282:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-mailbox.c: In function 'cx18_api_call':
media_build/v4l/cx18-mailbox.c:598:6: warning: variable 'state' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_capture_open':
media_build/v4l/cx18-alsa-pcm.c:156:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_capture_close':
media_build/v4l/cx18-alsa-pcm.c:202:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_hw_params':
media_build/v4l/cx18-alsa-pcm.c:255:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-streams.c: In function 'cx18_stop_v4l2_encode_stream':
media_build/v4l/cx18-streams.c:983:16: warning: variable 'then' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtv-ioctl.c: In function 'ivtv_set_speed':
media_build/v4l/ivtv-ioctl.c:138:22: warning: variable 's' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtvfb.c: In function 'ivtvfb_init':
media_build/v4l/ivtvfb.c:1286:6: warning: variable 'err' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtvfb.c: In function 'ivtvfb_cleanup':
media_build/v4l/ivtvfb.c:1306:6: warning: variable 'err' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 14 May 2012 13:14:53 +0000 (10:14 -0300)]
[media] cx231xx: fix compiler warnings
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c: In function ‘snd_cx231xx_hw_capture_params’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:527:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:31: warning: variable ‘format’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:25: warning: variable ‘rate’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:15: warning: variable ‘channels’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c: In function ‘snd_cx231xx_capture_trigger’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:589:6: warning: variable ‘retval’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_isoc_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:331:17: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_bulk_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:434:17: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_reset_video_buffer’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:704:7: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_set_mode’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:699:6: warning: variable ‘errCode’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_ep5_bulkout’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:763:6: warning: variable ‘errCode’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_isoc_irq_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:800:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_bulk_irq_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:846:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_stop_TS1’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:1234:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_start_TS1’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:1254:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_enable656’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:937:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_disable656’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:955:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_dump_HH_reg’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1323:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_dump_SC_reg’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1358:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_Setup_AFE_for_LowIF’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1444:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_set_Colibri_For_LowIF’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1504:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_set_DIF_bandpass’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1559:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_gpio_i2c_write’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:3093:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c: In function ‘cx231xx_initialize_codec’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c:1098:9: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c: In function ‘vidioc_streamon’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c:1795:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c: In function ‘cx231xx_isoc_vbi_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c:86:25: warning: variable ‘buf’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c: In function ‘cx231xx_irq_vbi_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c:313:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 20 Apr 2012 06:30:11 +0000 (03:30 -0300)]
[media] dw2102: fix compile warnings
media_build/v4l/dw2102.c:151:13: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:224:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:279:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:352:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:435:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:499:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds V4L2_CID_EXPOSURE_METERING control which allows
to select the light metering mode for automatic exposure as one
of the following modes: spot (small area at the frame center),
center weighted and frame averaged.
[media] m5mols: Add auto and preset white balance control
Replace the V4L2_CID_AUTO_WHITE_BALANCE control with its extended
version - V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE so the white balance
presets feature is exposed to user land.
Acked-by: HeungJun Kim <riverful.kim@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] m5mols: Use proper sensor mode for the controls
The parameters corresponding to the V4L controls can be reconfigured
only in associated M-5MOLS operation mode. Use struct v4l2_ctrl
priv field to assign the working mode to the controls which can be
modified only in certain conditions.
This patch is a prerequisite for the new controls addition. It consolidates
the control handling code, which is moved to m5mols_controls.c and
staticized. The controls initialization is reordered to better reflect
the control clusters and make the diffs smaller when new controls are added.
To make the code easier to follow when more controls is added use separate
set function for each control.
The V4L2_CID_3A_LOCK bitmask control allows applications to pause
or resume the automatic exposure, focus and wite balance adjustments.
It can be used, for example, to lock the 3A adjustments right before
a still image is captured, for pre-focus, etc.
The applications can control each of the algorithms independently,
through a corresponding control bit, if driver allows that.
Add control for the scene mode feature available in image sensor
with more advanced ISP firmware. The V4L2_CID_SCENE_MODE menu
control allows to select a set of parameters or a specific image
processing and capture control algorithm optimized for common
image capture conditions.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_CID_EXPOSURE_METERING control allows to determine
a method used by the camera for measuring the amount of light
available for automatic exposure.
Add ISO sensitivity and ISO auto/manual controls. The sensitivity
values are related to level of amplification of the analog signal
between image sensor and ADC. These controls allow to support sensors
exposing an interface to accept the ISO values directly.
[media] V4L: Add camera image stabilization control
Add V4L2_CID_IMAGE_STABILIZATION control for the camera image
stabilization feature. This control can be used to enable/disable
image stabilization. It might get converted to a menu control
in future if more options are needed.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] V4L: Add camera wide dynamic range control
Add V4L2_CID_WIDE_DYNAMIC_RANGE camera class control for the
camera wide dynamic range (WDR, HDR) feature. This control
can be used to enable/disable wide dynamic range. It might
get converted to a menu control in future if more options
are needed.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] V4L: Add an extended camera white balance control
This patch adds V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE control which is
an extended version of the V4L2_CID_AUTO_WHITE_BALANCE control,
including white balance presets. The following presets are defined:
The camera may in some conditions incorrectly determine the exposure,
and a manual automatic exposure correction may be needed. This patch
adds V4L2_CID_AUTO_EXPOSURE_BIAS control which allows to add some
offset in the automatic exposure control loop, to compensate for
frame under- or over-exposure.
[media] V4L: Add helper function for standard integer menu controls
This patch adds v4l2_ctrl_new_int_menu() helper function which can be used
in drivers for creating standard integer menu control with driver-specific
menu item list. It is similar to v4l2_ctrl_new_std_menu(), except it doesn't
have a mask parameter and an additional qmenu parameter allows passing
an array of signed 64-bit integers as the menu item list.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Tested-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new V4L2_COLORFX_CBCR control is added to allow setting
the fixed Cb, Cr values that replace chroma Cb/Cr coefficients
in case of V4L2_COLORFX_SET_CBCR effect.
The radio-si470x-usb driver supported both autosuspend and it stopped the
radio the moment the last user of the radio device closed it. However, that
was very confusing since if you play the audio from the device (e.g. through
arecord -D ... | aplay) then no sound would play unless you had the radio
device open at the same time, even though there is no need to do anything
with that node.
On the other hand, the actual suspend/resume functions didn't do anything,
which would fail if you *did* have the radio node open at that time.
So:
- remove autosuspend (bad idea in general for USB radio devices)
- move the start/stop out of the open/release functions into the resume/suspend
functions.
[media] v4l: v4l2-ctrls: moves the forward declaration of struct file
This fixes the following warning:
In file included from drivers/media/video/v4l2-subdev.c:29:
include/media/v4l2-ctrls.h:501: warning: 'struct file' declared inside
parameter list
include/media/v4l2-ctrls.h:501: warning: its scope is only this
definition or declaration, which is probably not what you want
include/media/v4l2-ctrls.h:509: warning: 'struct file' declared inside
parameter list
Kartik Mohta [Wed, 2 May 2012 22:19:08 +0000 (19:19 -0300)]
[media] mt9v032: Correct the logic for the auto-exposure setting
The driver uses the ctrl value passed in as a bool to determine whether
to enable auto-exposure, but the auto-exposure setting is defined as an
enum where AUTO has a value of 0 and MANUAL has a value of 1. This leads
to a reversed logic where if you send in AUTO, it actually sets manual
exposure and vice-versa.
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1
Laurent Pinchart [Sat, 10 Mar 2012 00:02:57 +0000 (21:02 -0300)]
[media] mt9p031: Implement black level compensation control
Add four new controls to configure black level compensation (BLC):
- V4L2_CID_BLC_AUTO selects between manual and auto BLC
- V4L2_CID_BLC_TARGET_LEVEL sets the target level for auto BLC
- V4L2_CID_BLC_ANALOG_OFFSET sets the analog offset for manual BLC
- V4L2_CID_BLC_DIGITAL_OFFSET sets the digital offset for manual BLC
af9033: implement read_ber and read_ucblocks functions. Version 2 of patch that
reflects my findings on the behaviour of abort_cnt, err_cnt and bit_cnt:
- bit_cnt is always 0x2710 (10000)
- abort_cnt is between 0 and 0x2710
- err_cnt is between 0 and 640000 (= 0x2710 * 8 * 8)
in the current implementation BER is calculated as the number of bit errors per
processed bits, ignoring those bits that are already discarded and counted in
abort_cnt, i.e. UCBLOCKS.
Antti Palosaari [Fri, 6 Apr 2012 19:32:30 +0000 (16:32 -0300)]
[media] af9035: various small changes for af9035_ctrl_msg()
Fix USB buffer len to maximum possible.
Various log writing fixes, remove extra new lines and excessive
type casts. Rename and type change some variables.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] s5p-fimc: Fix locking in subdev set_crop op
When setting TRY crop on the sub-device the mutex was erroneously acquired
rather than released on exit path. This bug is present in kernels starting
from v3.2.
Antonio Ospite [Mon, 14 May 2012 11:07:44 +0000 (08:07 -0300)]
[media] Input: move drivers/input/fixp-arith.h to include/linux
Move drivers/input/fixp-arith.h to include/linux so that the functions
defined there can be used by other subsystems, for instance some video
devices ISPs can control the output HUE value by setting registers for
sin(HUE) and cos(HUE).
Hans de Goede [Thu, 10 May 2012 15:13:16 +0000 (12:13 -0300)]
[media] gspca_pac7311: Remove vflip control
Enabling vflip leads to a much better image, with vflip disabled the
image looks washed out as if there is a too high brightness setting.
Since we don't know how to lower the brightness setting when not
vflipping, simply always vflip and tell userspace to flip the image back,
resulting in a much better (less washed out) image.
Since the image is now no longer too bright, also modify the luminance
level the auto-gain algorithm aims for.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Thu, 10 May 2012 15:10:56 +0000 (12:10 -0300)]
[media] gspca_pac7311: Set register page at start of init
Our init sequence was not setting the register page to point to bank 1
before setting what should be the control reg. This causes the camera to
sometimes have its LED on after init. First selecting register bank 1,
rather then assuming the current register bank is bank 1, fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Wed, 9 May 2012 14:19:00 +0000 (11:19 -0300)]
[media] gscpa: Move ctrl_handler to gspca_dev
We intend to eventually port all sub-drivers to the control-framework. At
which point it will make more sense to have the ctrl_handler in gspca_dev
then to have it in the subdrivers. Lets move it there now, to avoid a lot
of work to move it later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 6 May 2012 12:28:31 +0000 (09:28 -0300)]
[media] gspca_mars: Convert to the control framework
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 6 May 2012 12:28:30 +0000 (09:28 -0300)]
[media] gspca_stv06xx: Convert to the control framework
HdG:
1) Let the gspca-core cleanup the controls on control-init error, like
with the other converted sub drivers
2) Note this also fixes a bug in the hdcs1020 support which was wrongly
reporting an exposure range of 0-65535, even though the effective range was
only 0-255
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 6 May 2012 12:28:29 +0000 (09:28 -0300)]
[media] gcpca_sn9c20x: Convert to the control framework
HdG: Small fix: don't register some controls for sensors which don't
have an implementation for them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 6 May 2012 12:28:28 +0000 (09:28 -0300)]
[media] gspca_zc3xx: Convert to the control framework
The initial version was done by HV, corrections were made by HdG, and some
final small changes again by HV.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Sun, 6 May 2012 12:28:26 +0000 (09:28 -0300)]
[media] gspca_zc3xx: Disable the highest quality setting as it is not usable
Even with BRC the highest quality setting is not usable, BRC strips so
much data from each MCU that the quality becomes worse then using a lower
quality setting to begin with.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Sun, 6 May 2012 12:28:25 +0000 (09:28 -0300)]
[media] gspca_zc3xx: Always automatically adjust BRC as needed
Always automatically adjust the Bit Rate Control setting as needed, independent
of the sensor type. BRC is needed to not run out of bandwidth with higher
quality settings independent of the sensor.
Also only automatically adjust BRC, and don't adjust the JPEG quality control
automatically, as that is not needed and leads to ugly flashes when it is
changed. Note that before this patch-set the quality was never changed
either due to the bugs in the quality handling fixed in previous patches in
this set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code is using bits 0-1 of register 8 of the zc3xx controller
to set the JPEG quality, but the correct bits are bits 1-2. Bit 0 selects
between truncation or rounding in the quantization phase of the compression,
since rounding generally gives better results it should thus always be 1.
This patch also corrects the quality percentages which belong to the 4
different settings.
Last this patch removes the different reg 8 defaults depending on the sensor
type. Some of them where going for a default quality setting of 50%, which
generally is not necessary in any way and results in poor image quality.
75% is a good default to use for all scenarios.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans de Goede [Sun, 6 May 2012 12:28:23 +0000 (09:28 -0300)]
[media] gspca_zc3xx: Fix setting of jpeg quality while streaming
When the user changes the JPEG quality while the camera is streaming, the
driver should not only change the JPEG headers send to userspace, but also
actually tell the camera to use a different quantization table.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>