Bruce Allan [Fri, 20 Nov 2009 23:24:30 +0000 (23:24 +0000)]
e1000e: Incorrect MII Link beat reporting.
The driver was only updating MII stats when an LSC up was detected and
the interface had not already been reported up to netdev. This meant
MII stats returned in response to an SIOCGMIIREG ioctl would always
show a link up if it had ever been up. This was misleading the networking
daemon guessnet, which uses this ioctl, into making improper network port
selections.
This fix adds a call to e1000_phy_read_status() to actively read the
mii stats before responding to the SIOCGMIIREG ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 20 Nov 2009 23:24:11 +0000 (23:24 +0000)]
e1000e: disable K1 on PCH LOM when in PHY loopback mode
When performing the ethtool PHY loopback test on PCH-based LOMs (82577 and
82578), disable K1 (a MAC-PHY interconnect low power mode) otherwise
packets might get corrupted.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 20 Nov 2009 23:23:53 +0000 (23:23 +0000)]
e1000e: improper return code signage
The e1000_get_cable_length_82577() should return a negative value upon
error.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 20 Nov 2009 23:23:34 +0000 (23:23 +0000)]
e1000e: link reporting problems
Copper links with WoL or management enabled (any condition which prevents
the phy from being powered down when the interface is taken down) were
always reporting link-up when the interface had been taken down. This
is because when the interface is taken down (ifconfig ethx down),
interrupts are disabled. With no interrupts, there is no LSC interrupt,
which is normally required to set "get_link_status", which instructs the
driver to query the device for link state. The fix is to force
get_link_status to true if the interface is not up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 20 Nov 2009 23:23:16 +0000 (23:23 +0000)]
e1000e: don't clean Rx ring while resetting
When using legacy interrupts, do not clean the Rx ring while resetting
otherwise traffic will not pass.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 20 Nov 2009 23:22:57 +0000 (23:22 +0000)]
e1000e: function pointers for ethtool set/get offloads
Provide missing function pointers for ethtool set/get offloads.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 20 Nov 2009 23:22:39 +0000 (23:22 +0000)]
e1000e: clearing interrupt timers causes descriptors to get flushed
Clearing the interrupt timers following an IMS clear has the unwanted
side-effect of flushing all descriptors immediately following a partial
write when interrupts are disabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 20 Nov 2009 23:22:20 +0000 (23:22 +0000)]
e1000e: add missing tests for 82583 in ethtool functions
Add tests for 82583 in a couple ethtool functions that were missed from the
initial hardware enablement submission.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Fri, 20 Nov 2009 23:22:01 +0000 (23:22 +0000)]
e1000e: check WoL mode is among set of supported modes
When setting WoL feature, check the supplied modes are all supported rather
than checking for no support. This way, if any new modes are added the
driver does not default to not complaining about it if we don't really
support it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 19 Nov 2009 12:42:21 +0000 (12:42 +0000)]
igb: Add full support for 82580 devices
This patch makes use of the 82580 PHY and MAC support added and adds a set
of supported device IDs for said hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 19 Nov 2009 12:42:01 +0000 (12:42 +0000)]
igb: add support for 82580 MAC
This patch adds support for the 82580 MAC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 19 Nov 2009 12:41:42 +0000 (12:41 +0000)]
igb: add support for the 82580 phy
This patch adds support for the phy included in the 82580 silicon family.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 19 Nov 2009 02:49:49 +0000 (18:49 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix stale cpufreq_cpu_governor pointer
[CPUFREQ] Resolve time unit thinko in ondemand/conservative govs
[CPUFREQ] speedstep-ich: fix error caused by 394122ab144dae4b276d74644a2f11c44a60ac5c
[CPUFREQ] Fix use after free on governor restore
[CPUFREQ] acpi-cpufreq: blacklist Intel 0f68: Fix HT detection and put in notification message
[CPUFREQ] powernow-k8: Fix test in get_transition_latency()
[CPUFREQ] longhaul: select Longhaul version 2 for capable CPUs
Linus Torvalds [Wed, 18 Nov 2009 21:31:52 +0000 (22:31 +0100)]
strcmp: fix overflow and possibly signedness error
Doing the strcmp return value as
signed char __res = *cs - *ct;
is wrong for two reasons. The subtraction can overflow because __res
doesn't use a type big enough. Moreover the compared bytes should be
interpreted as unsigned char as specified by POSIX.
The same problem is fixed in strncmp.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Michael Buesch <mb@bu3sch.de> Cc: Andreas Schwab <schwab@linux-m68k.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 19 Nov 2009 01:08:16 +0000 (17:08 -0800)]
Merge branch 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6
* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp/intel-agp: Set dma_mask for capable chipsets before agp_add_bridge()
Linus Torvalds [Wed, 18 Nov 2009 23:00:21 +0000 (15:00 -0800)]
Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP: cs should be positive in gpmc_cs_free()
omap: fix unlikely(x) < y
omap3: clock: Fixed dpll3_m2x2 rate calculation
omap3: clock: Fix the DPLL freqsel computations
omap: Fix keymap for zoom2 according to matrix keypad framwork
Linus Torvalds [Wed, 18 Nov 2009 22:59:49 +0000 (14:59 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: tlv320aic23 fix rate selection
ASoC: OMAP3 Pandora: update for TWL4030 codec changes
ASoC: Modifying the license string GPLv2 for OMAP3 EVM
ALSA: hda - Fix quirk for VAIO type G
ALSA: usb - Quirk to disable master volume control in PCM2702
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
cxgb3: fix premature page unmap
ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
vlan: Fix register_vlan_dev() error path
gro: Fix illegal merging of trailer trash
sungem: Fix Serdes detection.
net: fix mdio section mismatch warning
ppp: fix BUG on non-linear SKB (multilink receive)
ixgbe: Fixing EEH handler to handle more than one error
net: Fix the rollback test in dev_change_name()
Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation."
TI Davinci EMAC : Fix Console Hang when bringing the interface down
smsc911x: Fix Console Hang when bringing the interface down.
mISDN: fix error return in HFCmulti_init()
forcedeth: mac address fix
r6040: fix version printing
Bluetooth: Fix regression with L2CAP configuration in Basic Mode
Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET
Bluetooth: Set general bonding security for ACL by default
r8169: Fix receive buffer length when MTU is between 1515 and 1536
can: add the missing netlink get_xstats_size callback
...
Mimi Zohar [Wed, 18 Nov 2009 21:16:06 +0000 (16:16 -0500)]
ima: replace GFP_KERNEL with GFP_NOFS
While running fsstress tests on the NFSv4 mounted ext3 and ext4
filesystem, the following call trace was generated on the nfs
server machine.
Replace GFP_KERNEL with GFP_NOFS in ima_iint_insert() to avoid a
potential deadlock.
=================================
[ INFO: inconsistent lock state ]
2.6.31-31.el6.x86_64 #1
---------------------------------
inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
kswapd2/75 [HC0[0]:SC0[0]:HE1:SE1] takes:
(jbd2_handle){+.+.?.}, at: [<ffffffff811edd5e>] jbd2_journal_start+0xfe/0x13f
{RECLAIM_FS-ON-W} state was registered at:
[<ffffffff81091e40>] mark_held_locks+0x65/0x99
[<ffffffff81091f31>] lockdep_trace_alloc+0xbd/0xf5
[<ffffffff81126fdd>] kmem_cache_alloc+0x40/0x185
[<ffffffff812344d7>] ima_iint_insert+0x3d/0xf1
[<ffffffff812345b0>] ima_inode_alloc+0x25/0x44
[<ffffffff811484ac>] inode_init_always+0xec/0x271
[<ffffffff81148682>] alloc_inode+0x51/0xa1
[<ffffffff81148700>] new_inode+0x2e/0x94
[<ffffffff811b2f08>] ext4_new_inode+0xb8/0xdc9
[<ffffffff811be611>] ext4_create+0xcf/0x175
[<ffffffff8113e2cd>] vfs_create+0x82/0xb8
[<ffffffff8113f337>] do_filp_open+0x32c/0x9ee
[<ffffffff811309b9>] do_sys_open+0x6c/0x12c
[<ffffffff81130adc>] sys_open+0x2e/0x44
[<ffffffff81011e42>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
irq event stamp: 90371
hardirqs last enabled at (90371): [<ffffffff8112708d>]
kmem_cache_alloc+0xf0/0x185
hardirqs last disabled at (90370): [<ffffffff81127026>]
kmem_cache_alloc+0x89/0x185
softirqs last enabled at (89492): [<ffffffff81068ecf>]
__do_softirq+0x1bf/0x1eb
softirqs last disabled at (89477): [<ffffffff8101312c>] call_softirq+0x1c/0x30
other info that might help us debug this:
2 locks held by kswapd2/75:
#0: (shrinker_rwsem){++++..}, at: [<ffffffff810f98ba>] shrink_slab+0x44/0x177
#1: (&type->s_umount_key#25){++++..}, at: [<ffffffff811450ba>]
Reported-by: Muni P. Beerakam <mbeeraka@in.ibm.com> Reported-by: Amit K. Arora <amitarora@in.ibm.com> Cc: stable@kernel.org Signed-off-by: Mimi Zohar <zohar@us.ibm.com> Signed-off-by: James Morris <jmorris@namei.org>
Roel Kluin [Tue, 17 Nov 2009 22:39:06 +0000 (14:39 -0800)]
OMAP: cs should be positive in gpmc_cs_free()
The index `cs' is signed, test whether it is negative before we release
gpmc_cs_mem[cs].
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Roel Kluin [Tue, 17 Nov 2009 22:39:03 +0000 (14:39 -0800)]
omap: fix unlikely(x) < y
The closing parenthesis was not in the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Linus Torvalds [Wed, 18 Nov 2009 15:38:19 +0000 (07:38 -0800)]
Merge branch 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fixup last users of irq_chip->typename
uio: pm_runtime_disable is needed if failed
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: cp210x: Fix carrier handling
tty_port: If we are opened non blocking we still need to raise the carrier
ASoC: OMAP3 Pandora: update for TWL4030 codec changes
A while ago TWL4030 had it's playback stream name changed, but
pandora needs it for it's playback path. Update to correct stream
name so that playback works again.
Also mark VIBRA output as not connected.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dave Mitchell [Tue, 17 Nov 2009 14:56:55 +0000 (14:56 +0000)]
ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
The TRT bit shifts were reversed for EMAC4 and non-EMAC4 during the
port from ibm_emac to ibm_newemac. This patch corrects that error.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com> Acked-by: Feng Kan <fkan@appliedmicro.com> Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton [Tue, 17 Nov 2009 12:46:44 +0000 (12:46 +0000)]
drivers/atm/solos-pci.c: fix warning/bug, clean up code
drivers/atm/solos-pci.c: In function 'flash_upgrade':
drivers/atm/solos-pci.c:528: warning: 'fw_name' may be used uninitialized in this function
Cc: Chas Williams <chas@cmf.nrl.navy.mil> Cc: David Woodhouse <David.Woodhouse@intel.com> Cc: Nathan Williams <nathan@traverse.com.au> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-By: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Christian Pellegrin <chripell@fsfe.org> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 17 Nov 2009 05:59:21 +0000 (05:59 +0000)]
linkwatch: linkwatch_forget_dev() to speedup device dismantle
Herbert Xu a écrit :
> On Tue, Nov 17, 2009 at 04:26:04AM -0800, David Miller wrote:
>> Really, the link watch stuff is just due for a redesign. I don't
>> think a simple hack is going to cut it this time, sorry Eric :-)
>
> I have no objections against any redesigns, but since the only
> caller of linkwatch_forget_dev runs in process context with the
> RTNL, it could also legally emit those events.
Thanks guys, here an updated version then, before linkwatch surgery ?
In this version, I force the event to be sent synchronously.
[PATCH net-next-2.6] linkwatch: linkwatch_forget_dev() to speedup device dismantle
time ip link del eth3.103 ; time ip link del eth3.104 ; time ip link del eth3.105
real 0m0.266s
user 0m0.000s
sys 0m0.001s
real 0m0.770s
user 0m0.000s
sys 0m0.000s
real 0m1.022s
user 0m0.000s
sys 0m0.000s
One problem of current schem in vlan dismantle phase is the
holding of device done by following chain :
Octavian Purdila [Mon, 16 Nov 2009 13:49:35 +0000 (13:49 +0000)]
net: introduce NETDEV_UNREGISTER_PERNET
This new event is called once for each unique net namespace in batched
unregister operations (with the argument set to a random device from
that namespace) and once per device in non-batched unregister
operations.
It allows us to factorize some device unregister work such as clearing the
routing cache.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Prarit Bhargava [Thu, 12 Nov 2009 14:18:46 +0000 (09:18 -0500)]
[CPUFREQ] Fix stale cpufreq_cpu_governor pointer
Dave,
Attached is an update of my patch against the cpufreq fixes branch.
Before applying the patch I compiled and booted the tree to see if the panic
was still there -- to my surprise it was not. This is because of the conversion
of cpufreq_cpu_governor to a char[].
While the panic is kaput, the problem of stale data continues and my patch is
still valid. It is possible to end up with the wrong governor after hotplug
events because CPUFREQ_DEFAULT_GOVERNOR is statically linked to a default,
while the cpu siblings may have had a different governor assigned by a user.
ie) the patch is still needed in order to keep the governors assigned
properly when hotplugging devices
Signed-off-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Dave Jones <davej@redhat.com>
[CPUFREQ] Resolve time unit thinko in ondemand/conservative govs
ondemand and conservative governors are messing up time units in the
code path where NO_HZ is not enabled and ignore_nice is set. The walltime
idletime stored is in jiffies and nice time calculation is happening in
microseconds.
The problem was reported and diagnosed by Alexander here.
http://marc.info/?l=linux-kernel&m=125752550404513&w=2
The patch below fixes this thinko.
Reported-by: Alexander Miller <Miller@fmi.uni-stuttgart.de> Tested-by: Alexander Miller <Miller@fmi.uni-stuttgart.de> Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Dave Jones <davej@redhat.com>
"[CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c"
changed the code to mistakenly pass the current cpu as the "processor"
argument of speedstep_get_frequency(), whereas it should be the type of
the processor.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Dominik Brodowski <linux@brodo.de> Reported-by: Dave Mueller <dave.mueller@gmx.ch> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dave Jones <davej@redhat.com>
Dmitry Monakhov [Sun, 4 Oct 2009 20:38:55 +0000 (00:38 +0400)]
[CPUFREQ] Fix use after free on governor restore
Currently on governer backup/restore path we storing governor's pointer.
This is wrong because one may unload governor's module after cpu goes
offline. As result use-after-free will take place on restored cpu.
It is not easy to exploit this bug, but still we have to close this
issue ASAP. Issue was introduced by following commit 084f34939424161669467c19280dbcf637730314
##TESTCASE##
#!/bin/sh -x
modprobe acpi_cpufreq
# Any non default governor, in may case it is "ondemand"
modprobe cpufreq_ondemand
echo ondemand > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
rmmod acpi_cpufreq
rmmod cpufreq_ondemand
modprobe acpi_cpufreq # << use-after-free here.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org> Signed-off-by: Dave Jones <davej@redhat.com>
John Villalovos [Fri, 25 Sep 2009 17:30:08 +0000 (13:30 -0400)]
[CPUFREQ] acpi-cpufreq: blacklist Intel 0f68: Fix HT detection and put in notification message
Removing the SMT/HT check, since the Errata doesn't mention
Hyper-Threading.
Adding in a printk, so that the user knows why acpi-cpufreq refuses to
load. Also, once system is blacklisted, don't repeat checks to see if
blacklisted. This also causes the message to only be printed once,
rather than for each CPU.
Signed-off-by: John L. Villalovos <john.l.villalovos@intel.com> Signed-off-by: Dave Jones <davej@redhat.com>
Krzysztof Helt [Sat, 24 Oct 2009 15:25:38 +0000 (17:25 +0200)]
[CPUFREQ] longhaul: select Longhaul version 2 for capable CPUs
There is a typo in the longhaul detection code so only Longhaul v1 or Longhaul v3
is selected. The Longhaul v2 is not selected even for CPUs which are capable of.
Tested on PCChips Giga Pro board. Frequency changes work and the Longhaul v2
detects that the board is not capable of changing CPU voltage.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Dave Jones <davej@redhat.com>
Peter Zijlstra [Tue, 17 Nov 2009 22:06:24 +0000 (14:06 -0800)]
fcntl: rename F_OWNER_GID to F_OWNER_PGRP
This is for consistency with various ioctl() operations that include the
suffix "PGRP" in their names, and also for consistency with PRIO_PGRP,
used with setpriority() and getpriority(). Also, using PGRP instead of
GID avoids confusion with the common abbreviation of "group ID".
I'm fine with anything that makes it more consistent, and if PGRP is what
is the predominant abbreviation then I see no need to further confuse
matters by adding a third one.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andi Kleen [Tue, 17 Nov 2009 22:06:22 +0000 (14:06 -0800)]
mm: allow memory hotplug and hibernation in the same kernel
Allow memory hotplug and hibernation in the same kernel
Memory hotplug and hibernation were exclusive in Kconfig. This is
obviously a problem for distribution kernels who want to support both in
the same image.
After some discussions with Rafael and others the only problem is with
parallel memory hotadd or removal while a hibernation operation is in
process. It was also working for s390 before.
This patch removes the Kconfig level exclusion, and simply makes the
memory add / remove functions grab the pm_mutex to exclude against
hibernation.
Fixes a regression - old kernels didn't exclude memory hotadd and
hibernation.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun Heo [Tue, 17 Nov 2009 22:06:20 +0000 (14:06 -0800)]
workqueue: fix race condition in schedule_on_each_cpu()
Commit 65a64464349883891e21e74af16c05d6e1eeb4e9 ("HWPOISON: Allow
schedule_on_each_cpu() from keventd") which allows schedule_on_each_cpu()
to be called from keventd added a race condition. schedule_on_each_cpu()
may race with cpu hotplug and end up executing the function twice on a
cpu.
Fix it by moving direct execution into the section protected with
get/put_online_cpus(). While at it, update code such that direct
execution is done after works have been scheduled for all other cpus and
drop unnecessary cpu != orig test from flush loop.
Hidetoshi Seto [Tue, 17 Nov 2009 22:06:18 +0000 (14:06 -0800)]
mm/memory_hotplug: fix section mismatch
With CONFIG_MEMORY_HOTPLUG I got following warning:
WARNING: vmlinux.o(.text+0x1276b0): Section mismatch in reference from
the function hotadd_new_pgdat() to the function
.meminit.text:free_area_init_node()
The function hotadd_new_pgdat() references
the function __meminit free_area_init_node().
This is often because hotadd_new_pgdat lacks a __meminit
annotation or the annotation of free_area_init_node is wrong.
Zhang Le [Wed, 4 Nov 2009 15:22:59 +0000 (23:22 +0800)]
USB: option.c: add support for D-Link DWM-162-U5
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be
switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
Alan Stern [Wed, 4 Nov 2009 16:35:53 +0000 (11:35 -0500)]
USB: usbmon: fix bug in mon_buff_area_shrink
This patch (as1299b) fixes a bug in an error-handling path of usbmon's
binary interface. The storage area for URB data is divided into
fixed-size blocks. If an URB's data can't be copied, the area
reserved for it should be decreased to the size of the truncated
information (rounded up to a block boundary). Rounding up the amount
to be removed and subtracting it from the reserved size is definitely
the wrong thing to do.
Also, when the data for an isochronous URB can't be copied, we can
still copy the isoc packet descriptors. In fact the current code does
copy the descriptors, but then sets the capture length to 0 so they
remain inaccessible. The capture length should be reduced to the
length of the descriptors, not set to 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Pete Zaitcev <zaitcev@redhat.com> CC: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Wed, 4 Nov 2009 19:22:19 +0000 (11:22 -0800)]
USB: xhci: Fix scratchpad deallocation.
The scratchpad_free() function uses xhci->page_size to free some memory
with pci_free_consistent(). However, the page_size is set to zero before
the call, causing kernel oopses on driver unload. Call scratchpad_free()
before setting xhci->page_size to zero.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: John Youn <John.Youn@synopsys.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Wed, 4 Nov 2009 06:02:24 +0000 (22:02 -0800)]
USB: xhci: Fix TRB physical to virtual address translation.
The trb_in_td() function in the xHCI driver is supposed to translate a
physical transfer buffer request (TRB) into a virtual pointer to the ring
segment that TRB is in.
Unfortunately, a mistake in this function may cause endless loops as the
driver searches through the linked list of ring segments over and over
again. Fix a couple bugs that may lead to loops or bad output:
1. Bail out if we get a NULL pointer when translating the segment's
private structure and the starting DMA address of the segment chunk. If
this happens, we've been handed a starting TRB pointer from a different
ring.
2. Make sure the function works when there's multiple segments in the
ring. In the while loop to search through the ring segments, use the
current segment variable (cur_seg), rather than the starting segment
variable (start_seg) that is passed in.
3. Stop searching the ring if we've run through all the segments in the
ring.
Sarah Sharp [Wed, 4 Nov 2009 06:02:22 +0000 (22:02 -0800)]
USB: xhci: Fix bug memory free after failed initialization.
If the xHCI driver fails during the memory initialization, xhci->ir_set
may not be a valid pointer. Check that it points to valid DMA'able memory
before writing to that address during the memory freeing process.
Francesco Lavra [Tue, 3 Nov 2009 10:53:07 +0000 (10:53 +0000)]
USB: cdc_acm: Fix memory leak after hangup
Am Donnerstag, 10. September 2009 15:43:53 schrieb Dietmar Hilbrich:
> Hello,
>
> i have the following problem with the cdc-acm - driver:
>
> I'm using the driver with an "Ericsson F3507G" on a Thinkpad T400.
>
> If a disable the device (with the RFKill-Switch) while it is used by a
> programm like ppp, the driver doesn't seem to correctly clean up the tty,
> even after the program has been closed)
>
> The tty is still active (e.g. there still exists an entry in
> /sys/dev/char/166:0 if ttyACM0 was used) and if a reacticate the device,
> this device entry will be skipped and the Device-Nodes ttyACM1, ttyACM2
> and ttyACM3 will be used.
>
> This problem was introduced with the commit
> 10077d4a6674f535abdbe25cdecb1202af7948f1 (before 2.6.31-rc1) and still
> exists in 2.6.31.
>
> I was able the fix this problem with the following patch:
>
> diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
> index 2bfc41e..0970d2f 100644
> --- a/drivers/usb/class/cdc-acm.c
> +++ b/drivers/usb/class/cdc-acm.c
> @@ -676,6 +676,7 @@ static void acm_tty_hangup(struct tty_struct *tty)
> struct acm *acm = tty->driver_data;
> tty_port_hangup(&acm->port);
> acm_port_down(acm, 0);
> + acm_tty_unregister(acm);
> }
I have the same problem with cdc-acm (I'm using a Samsung SGH-U900): when I
unplug it from the USB port during a PPP connection, the ppp daemon gets the
hangup correctly (and closes the device), but the struct acm corresponding to
the device disconnected is not freed. Hence reconnecting the device results in
creation of /dev/ttyACM(x+1). The same happens when the system is hibernated
during a PPP connection.
This memory leak is due to the fact that when the tty is hung up,
tty_port_close_start() returns always zero, and acm_tty_close() never reaches
the point where acm_tty_unregister() is called.
Here is a fix for this.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Libin Yang [Wed, 4 Nov 2009 06:55:18 +0000 (14:55 +0800)]
USB: ohci: quirk AMD prefetch for USB 1.1 ISO transfer
The following patch in the driver is required to avoid USB 1.1 device
failures that may occur due to requests from USB OHCI controllers may
be overwritten if the latency for any pending request by the USB
controller is very long (in the range of milliseconds).
Signed-off-by: Libin Yang <libin.yang@amd.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Wed, 28 Oct 2009 20:12:33 +0000 (21:12 +0100)]
tty: cp210x: Fix carrier handling
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=2
9a68e39d4a701fb3be03cae9b462408664ebd205 broke carrier handling so that a
cp210x setup which needed the carrier lines set up (non CLOCAL) which did
not make a call which set the termios bits left the lines down even if
CLOCAL was not asserted.
Fix this not by reverting but by adding the proper dtr_rts and
carrier_raised methods. This both sets the modem lines properly and also
implements the correct blocking semantics for the port as required by
POSIX.
Signed-off-by: Alan Cox <alan@linux.intel.com> Reported-by: Karl Hiramoto <karl@hiramoto.org> Tested-by: Karl Hiramoto <karl@hiramoto.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>