Andreas Mohr [Sun, 31 Jan 2010 02:58:42 +0000 (02:58 +0000)]
MCS7830 USB-Ether: resume _with_ working link, via .reset_resume support
ChangeLog:
Implement .reset_resume support to retain a live network connection
during suspend despite USB power loss.
- rework operation to reference cached data in mcs7830_data and
netdev->dev_addr
- update netdev->dev_addr only in case new MAC was set successfully
. Tests done:
. ethtool -d pre-/post-suspend: register values match
. running ssh session suspend, resume: works
. ifdown device, suspend, resume: works
. ifup, suspend, unplug, resume: WORKS (eth1 is removed, re-ifup of eth1
after card replug works)
. verified identical MAC in ifconfig post-resume
(ok, should be verified on network side to be fully certain...)
Keywords: suspend resume network connection dead interface down
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback test (offline) added in ethtool self test.
o Set device in loopback mode
o Send packets
o Process receive packets in qlcnic_process_rcv_ring_diag()
o Compare packets
o Reset device in normal mode.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt test (offline) added in ethtool self test.
Register a temporary interrupt handler and then send command to fw
to raise an interrupt.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic: support LED blink for device identification
Added support of device identification by blinking LED for specified time.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
o context resources can be in used, while resoruce cleanup is in progress,
during fw recover.
o Null pointer execption can occur in send_cmd_desc, if fw recovery
module frees tx ring without rtnl lock.
o Same applies to ethtool register dump and FW health registers should be dump
in any case.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Added missing identifier that distinguishes between
FCOE/ISCSI/ETHERNET functions.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shirley Ma [Fri, 29 Jan 2010 03:20:04 +0000 (03:20 +0000)]
virtio_net: Defer skb allocation in receive path Date: Wed, 13 Jan 2010 12:53:38 -0800
virtio_net receives packets from its pre-allocated vring buffers, then it
delivers these packets to upper layer protocols as skb buffs. So it's not
necessary to pre-allocate skb for each mergable buffer, then frees extra
skbs when buffers are merged into a large packet. This patch has deferred
skb allocation in receiving packets for both big packets and mergeable buffers
to reduce skb pre-allocations and skb frees. It frees unused buffers by calling
detach_unused_buf in vring, so recv skb queue is not needed.
Signed-off-by: Shirley Ma <xma@us.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Shirley Ma [Fri, 29 Jan 2010 03:19:05 +0000 (03:19 +0000)]
virtio: Add ability to detach unused buffers from vrings
There's currently no way for a virtio driver to ask for unused
buffers, so it has to keep a list itself to reclaim them at shutdown.
This is redundant, since virtio_ring stores that information. So
add a new hook to do this.
Signed-off-by: Shirley Ma <xma@us.ibm.com> Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Flavio Leitner [Tue, 2 Feb 2010 15:32:29 +0000 (07:32 -0800)]
igmp: fix ip_mc_sf_allow race [v5]
Almost all igmp functions accessing inet->mc_list are protected by
rtnl_lock(), but there is one exception which is ip_mc_sf_allow(),
so there is a chance of either ip_mc_drop_socket or ip_mc_leave_group
remove an entry while ip_mc_sf_allow is running causing a crash.
Signed-off-by: Flavio Leitner <fleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Tue, 2 Feb 2010 15:21:34 +0000 (07:21 -0800)]
can: deny filterlist access on non-CAN interfaces
In commit 20dd3850bcf860561496827b711fa10fecf6e787 "can: Speed up CAN frame
receiption by using ml_priv" the formerly used hlist of receiver lists for
each CAN netdevice has been replaced.
The hlist content ensured only CAN netdevices to be accessed by the
can_rx_(un)register() functions which accidently dropped away together with
the hlist receiver implementation.
This patch re-introduces the check for CAN netdevices in can_rx_(un)register().
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:29 +0000 (20:59 +0000)]
tulip/xircom_cb.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME and xircom_cb from pr_<level>
Convert embedded function names in logging messages to %s, __func__
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:28 +0000 (20:59 +0000)]
tulip/winbond-840.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Convert %d.%d.%d.%d to %pI4
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:27 +0000 (20:59 +0000)]
tulip/uli526x.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME from logging messages
Add do {} while(0) to ULI526X_DBUG macro
Make SHOW_MEDIA_TYPE macro more readable
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:26 +0000 (20:59 +0000)]
tulip/timer.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:25 +0000 (20:59 +0000)]
tulip/pnic2.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:24 +0000 (20:59 +0000)]
tulip/pnic.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:23 +0000 (20:59 +0000)]
tulip/media.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:22 +0000 (20:59 +0000)]
tulip/interrupt.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:21 +0000 (20:59 +0000)]
tulip/eeprom.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:20 +0000 (20:59 +0000)]
tulip/dmfe.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove 'DRV_NAME ": ' from logging messages
Convert commented out printks to pr_debug
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:19 +0000 (20:59 +0000)]
tulip/de2104x.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 28 Jan 2010 20:59:18 +0000 (20:59 +0000)]
tulip/21142.c: Use dev_<level> and pr_<level>
Convert printks to dev_<level> where a dev is available
Convert printks to pr_<level> where not
Coalesce format strings
Change print formats with %d.dx to %0dx
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an additional queuing strategy, called pfifo_head_drop,
to remove the oldest skb in the case of an overflow within the queue -
the head element - instead of the last skb (tail). To remove the oldest
skb in congested situations is useful for sensor network environments
where newer packets reflect the superior information.
Reviewed-by: Florian Westphal <fw@strlen.de> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Mon, 25 Jan 2010 10:37:54 +0000 (10:37 +0000)]
netns xfrm: xfrm6_tunnel in netns
I'm not sure about rcu stuff near kmem cache destruction:
* checks for non-empty hashes look bogus, they're done _before_
rcu_berrier()
* unregistering netns ops is done before kmem_cache destoy
(as it should), and unregistering involves rcu barriers by itself
So it looks nothing should be done.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The convention for API functions in kernel is to return errno value;
bond_open would return -1 if alb setup failed. The only reason that
could happen is if kmalloc() failed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Wed, 27 Jan 2010 16:38:06 +0000 (16:38 +0000)]
ixgbe: if ixgbe_copy_dcb_cfg is going to fail learn about it early
Call ixgbe_copy_dcb_cfg() earlier in the ixgbe_dcbnl_set_all() so that
we can learn if this is going to fail as early as possible. Previously,
ixgbe_down or ixgbe_close were being called before this check and the
IXGBE_RESETTING bit was being set and cleared. Worse if this failed
the corresponding ixgbe_up/ndo_open would not called.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Wed, 27 Jan 2010 16:37:44 +0000 (16:37 +0000)]
ixgbe: set the correct DCB bit for pg tx settings
Set the correct bit BIT_PG_TX when tx PG settings are set.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 27 Jan 2010 15:30:39 +0000 (15:30 +0000)]
igbvf: fix issue w/ mapped_as_page being left set after unmap
This change fixes an issue in igbvf with mapped_as_page being left set
after a page is unmapped which results in buffers which are mapped via map
single being unmapped as page.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 26 Jan 2010 11:40:11 +0000 (11:40 +0000)]
net/atm/mpoa_proc.c: checkpatch cleanups
Convert #include <asm... to #include <linux...
Add printk argument verification to dprintk and ddprintk
Spacing cleanups
Mostly 80 column wrapped.
Removed unnecessary breaks after returns
Use %pI4 in seq_printf of IP address
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 26 Jan 2010 11:40:09 +0000 (11:40 +0000)]
net/atm/mpc.c: checkpatch cleanups
Convert #include <asm... to #include <linux...
Add printk argument verification to dprintk and ddprintk
Spacing cleanups
Mostly 80 column wrapped.
printk->pr_info and pr_cont
Moved labels to column 1
Move trailing statements to new lines
switch/case cleanups
remove unnecessary breaks after returns
Remove unnecessary braces around single line statements
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 26 Jan 2010 11:40:08 +0000 (11:40 +0000)]
net/atm/lec.c: checkpatch cleanups
Convert #include <asm... to #include <linux...
Mostly 80 column wrapped.
Spacing cleanups
Convert printks to pr_<level>
Use print_hex_dump
Move embedded assigns out of tests
Move trailing statements to new lines
Remove unnecessary braces around single line statements
switch/case cleanups
Removed paren around returns
Use %pM
Moved leading continuation logical tests to end of previous line
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 26 Jan 2010 11:40:06 +0000 (11:40 +0000)]
net/atm/common.c: checkpatch cleanups
Convert #include <asm... to #include <linux...
Move EXPORT_SYMBOL
Spacing cleanups
Use __func__ in printks
Indent switch/case statements
Move trailing statements to new line
Hoist assigns from if tests
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 26 Jan 2010 11:40:04 +0000 (11:40 +0000)]
net/atm/br2684.c: checkpatch cleanups
Convert #include <asm... to #include <linux...
Use print_hex_dump
Spacing cleanups
Move logical continuation tests to end of previous line
80 column wrapping
Move goto branch label to column 1
Remove unnecessary single statement braces
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Tue, 26 Jan 2010 11:40:00 +0000 (11:40 +0000)]
net/atm: Convert printk to pr_<level>
Add #define pr_fmt(fmt) KBUILD_MODNAME ":%s: " fmt, __func__
Remove function names from output
Use single line pr_debug instead of broken multiple uses without newline
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 26 Jan 2010 18:27:09 +0000 (18:27 +0000)]
starfire: clean up properly if firmware loading fails
netdev_open() will return without cleaning up net device or hardware state
if firmware loading fails. This results in a BUG() on a second attempt to
bring the interface up, reported in
<http://bugzilla.kernel.org/show_bug.cgi?id=15091>, and probably has even
worse effects if the driver is removed afterwards.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Reported-by: Michael Moffatt <michael@moffatt.org.nz> Tested-by: Michael Moffatt <michael@moffatt.org.nz> Cc: "David S. Miller" <davem@davemloft.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Tue, 26 Jan 2010 07:58:57 +0000 (15:58 +0800)]
mac80211: fix NULL pointer dereference when ftrace is enabled
I got below kernel oops when I try to bring down the network interface if
ftrace is enabled. The root cause is drv_ampdu_action() is passed with a
NULL ssn pointer in the BA session tear down case. We need to check and
avoid dereferencing it in trace entry assignment.
Cc: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shan Wei [Tue, 26 Jan 2010 02:40:38 +0000 (02:40 +0000)]
ipv6: conntrack: Add member of user to nf_ct_frag6_queue structure
The commit 0b5ccb2(title:ipv6: reassembly: use seperate reassembly queues for
conntrack and local delivery) has broken the saddr&&daddr member of
nf_ct_frag6_queue when creating new queue. And then hash value
generated by nf_hashfn() was not equal with that generated by fq_find().
So, a new received fragment can't be inserted to right queue.
The patch fixes the bug with adding member of user to nf_ct_frag6_queue structure.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 25 Jan 2010 23:51:01 +0000 (15:51 -0800)]
virtio_net: Make delayed refill more reliable
I have seen RX stalls on a machine that experienced a suspected
OOM. After the stall, the RX buffer is empty on the guest side
and there are exactly 16 entries available on the host side. As
the number of entries is less than that required by a maximal
skb, the host cannot proceed.
The guest did not have a refill job scheduled.
My diagnosis is that an OOM had occured, with the delayed refill
job scheduled. The job was able to allocate at least one skb, but
not enough to overcome the minimum required by the host to proceed.
As the refill job would only reschedule itself if it failed completely
to allocate any skbs, this would lead to an RX stall.
The following patch removes this stall possibility by always
rescheduling the refill job until the ring is totally refilled.
Testing has shown that the RX stall no longer occurs whereas
previously it would occur within a day.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 25 Jan 2010 23:49:59 +0000 (15:49 -0800)]
sfc: Use fixed-size buffers for MCDI NVRAM requests
The low-level MCDI code always uses 32-bit MMIO operations, and
callers must pad input and output buffers to multiples of 4 bytes.
The MCDI NVRAM functions are not doing this. Also, their buffers are
declared as variable-length arrays with no explicit maximum length.
Switch to a fixed buffer size based on the chunk size used by the
MTD driver (which is a multiple of 4).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guido Barzini [Mon, 25 Jan 2010 23:49:19 +0000 (15:49 -0800)]
sfc: Add workspace for GMAC bug workaround to MCDI MAC_STATS buffer
Due to a hardware bug in the SFC9000 family, the firmware must
transfer raw GMAC statistics to host memory before aggregating them
into the cooked (speed-independent) MAC statistics. Extend the stats
buffer to support this.
The length of the buffer is explicit in the MAC_STATS command, so this
change is backward-compatible on both sides.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
By rounding up the buffer size to power of 2, several expensive
modulus operations can be avoided. This patch also solves a bug where
the gap need when ring gets full was not being accounted for.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
changed the hw attach code to fix up initialization values only for
dual band devices, however the commit message did not give a reason as
to why this would be useful or necessary.
According to tests by Jorge Boncompte, this breaks at least some
2GHz-only cards, so the code should be changed back to the
unconditional INI fixup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Jorge Boncompte <jorge@dti2.net> Cc: stable@kernel.org Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 22 Jan 2010 22:22:34 +0000 (14:22 -0800)]
iwlwifi: fix pointer signedness warning
There are a few station addresses that are
char *, instead of the normal u8 *; gcc
gives pointer signedness warnings for some
of those, so use u8 * consistently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexey Dobriyan [Mon, 25 Jan 2010 06:47:53 +0000 (22:47 -0800)]
netns xfrm: deal with dst entries in netns
GC is non-existent in netns, so after you hit GC threshold, no new
dst entries will be created until someone triggers cleanup in init_net.
Make xfrm4_dst_ops and xfrm6_dst_ops per-netns.
This is not done in a generic way, because it woule waste
(AF_MAX - 2) * sizeof(struct dst_ops) bytes per-netns.
Reorder GC threshold initialization so it'd be done before registering
XFRM policies.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Obviously, this register had some other impact that is causing
the regression. Either it is masking some other access or needs
to be reset in some path.
Either, way it is best to just revert the change for 2.6.33
Eric Dumazet [Mon, 25 Jan 2010 03:52:24 +0000 (19:52 -0800)]
vlan: fix vlan_skb_recv()
Bruno Prémont found commit 9793241fe92f7d930
(vlan: Precise RX stats accounting) added a regression for non
hw accelerated vlans.
[ 26.390576] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 26.396369] IP: [<df856b89>] vlan_skb_recv+0x89/0x280 [8021q]
vlan_dev_info() was used with original device, instead of
skb->dev. Also spotted by Américo Wang.
Reported-By: Bruno Prémont <bonbons@linux-vserver.org> Tested-By: Bruno Prémont <bonbons@linux-vserver.org> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
"ip xfrm state|policy count" report SA/SP count from init_net,
not from netns of caller process.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike McCormack [Sat, 23 Jan 2010 10:09:26 +0000 (02:09 -0800)]
sky2: Enable/disable WOL per hardware device
Y2_HW_WOL_ON/Y2_HW_WOL_OFF should be set and cleared per chip,
not per port. On dual port cards, Y2_HW_WOL_ON should be
enabled if either sky2 port has WOL enabled.
Found while reviewing code for a WOL regression, though this is
probably not the cause of the regression.
Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Sat, 23 Jan 2010 10:06:26 +0000 (02:06 -0800)]
ixgbevf: Fix IPv6 GSO type checks
Based on patch from Sridhar Samudrala
The following patch fixes the check for IPv6 GSO packet in ixgbevf
driver to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
CC: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Fix IPv6 GSO type checks in Intel ethernet drivers
Found this problem when testing IPv6 from a KVM guest to a remote
host via e1000e device on the host.
The following patch fixes the check for IPv6 GSO packet in Intel
ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shan Wei [Sat, 23 Jan 2010 09:57:42 +0000 (01:57 -0800)]
IP: Send an ICMP "Fragment Reassembly Timeout" message when enabling connection track
No matter whether connection track is enabled, an end host should send
an ICMPv4 "Fragment Reassembly Timeout" message when defrag timeout.
The reasons are following two points:
1. RFC 792 says:
>>>> >> > > If a host reassembling a fragmented datagram cannot complete the
>>>> >> > > reassembly due to missing fragments within its time limit it
>>>> >> > > discards the datagram, and it may send a time exceeded message.
>>>> >> > >
>>>> >> > > If fragment zero is not available then no time exceeded need be
>>>> >> > > sent at all.
>>>> >> > >
>>>> >> > > Read more: http://www.faqs.org/rfcs/rfc792.html#ixzz0aOXRD7Wp
2. Patrick McHardy also agrees with this opinion. :-)
About the discussion of this opinion, refer to http://patchwork.ozlabs.org/patch/41649
The patch fixed the problem like this:
When enabling connection track, fragments are received at PRE_ROUTING HOOK.
If they are failed to reassemble, ip_expire() will be called.
Before sending an ICMP "Fragment Reassembly Timeout" message,
the patch searches router table to get the destination entry only for host type.
The patch has been tested on both host type and route type.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Sat, 23 Jan 2010 09:35:00 +0000 (01:35 -0800)]
igb/igbvf: cleanup exception handling in tx_map_adv
After removing the skb_dma_map/unmap calls the exception handling in
igb_tx_map_adv is not correct. The issue is that the count value was not
being correctly handled so as a result we were not rewinding the ring as
back as we should have been.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose [Fri, 22 Jan 2010 22:47:37 +0000 (22:47 +0000)]
ixgbevf: Tell network stack to stop tx when the VF detects PF reset
When the VF detects that the PF has reset turn off carrier and stop all
tx queues.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose [Fri, 22 Jan 2010 22:47:18 +0000 (22:47 +0000)]
ixgbevf: Fix panics in the VF driver
Fix panics in the VF driver that occur when you bring it down after
having already brought the PF down.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose [Fri, 22 Jan 2010 22:47:00 +0000 (22:47 +0000)]
ixgbevf: Take action when the PF notifies the VF it is resetting.
When the VF driver gets a control message from the PF that indicates the
PF is about to reset or go down we schedule the watchdog timer so that
it will detect the PF has gone offline and take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose [Fri, 22 Jan 2010 22:46:40 +0000 (22:46 +0000)]
ixgbe: Improve reset coordination between the PF and the VF
Inadequate coordination between the PF driver and the VF driver results
in tx hangs in the VF driver when you perform certain actions that will
lead to a re-init of the PF. Add feature to notify active VFs when the PF
is about to re-initialize so that the VFs can take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose [Fri, 22 Jan 2010 22:46:22 +0000 (22:46 +0000)]
ixgbe: Allow the VF driver to be loaded before the PF driver
The PF Reset Done bit should not be set in the extended control register
until the PF has actually completed the bring up process. It is a mis-
interpretation of the purpose of this bit to assume it should be set
when the physical reset of the device is done. Instead it should be used
to indicate to the VFs when the PF is ready to provide them with required
services. This is not until after the PF is finished coming up and ready
to process mailbox events.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose [Fri, 22 Jan 2010 22:46:02 +0000 (22:46 +0000)]
ixgbe: Remove unused emulation MAC storage from the per VF data structure.
This data storage for SW emulated MAC addresses is unlikely to ever be used
so pull it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>