Hans Verkuil [Tue, 12 Feb 2013 08:25:38 +0000 (05:25 -0300)]
[media] stk-webcam: add ASUS F3JC to upside-down list
And add an extensive comment relating the history of the upside-down
handling in this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Arvydas Sidorenko <asido4@gmail.com> Thanks-to: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 7 Feb 2013 16:22:06 +0000 (13:22 -0300)]
[media] cx231xx: disable 417 support from the Conexant video grabber
The 417 support doesn't work. Until someone can dig into this driver to
figure out why it isn't working the 417 support is disabled.
Sometimes you can actually stream a bit, but very soon the whole machine
crashes, so something is seriously wrong.
For the record, this was not introduced by my recent changes to this driver,
it was broken before that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Colorspace, field and priv were not set, and sizeimage was calculated
using the wrong values (dev->ts1.ts_packet_size and dev->ts1.ts_packet_count
can be 0 at module load).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Tue, 29 Jan 2013 13:50:54 +0000 (10:50 -0300)]
[media] cx231xx: improve std handling
Set the initial standard of subdevices instead of leaving it undefined.
Also update the width and height when a new standard is chosen and
return -EBUSY when attempting to change the standard while videobuf is
busy.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 17 Sep 2012 11:30:07 +0000 (08:30 -0300)]
[media] cx231xx: remove current_norm usage
The use of this field is deprecated since it will not work when multiple
device nodes reference the same video input (the video and vbi nodes in
this case). The norm field should be a device-global value.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sat, 9 Feb 2013 09:41:11 +0000 (06:41 -0300)]
[media] cx231xx: fix vbi compliance issues
Various v4l2-compliance fixes: remove unused sliced VBI functions, zero the
reserved fields of struct v4l2_vbi_format and implement the missing s_fmt_vbi_cap.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 13 Sep 2012 15:54:36 +0000 (12:54 -0300)]
[media] cx231xx: fix tuner compliance issues
The g_tuner call wasn't passed on to the subdevices, g_frequency didn't
check for invalid tuners and a low-level function that was expected to
return 0 or a negative error returned a positive number instead, causing
s_frequency to return bogus errors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 13 Sep 2012 09:17:47 +0000 (06:17 -0300)]
[media] cx231xx: remove broken audio input support from the driver
The audio selection code is broken. Audio and video indices were
mixed up and s_audio would reject changing the audio input to
something else anyway, so what's the point?
All the audio input code has been removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 15 Feb 2013 09:56:48 +0000 (06:56 -0300)]
[media] bttv: remove g/s_audio since there is only one audio input
Note that the current driver does not implement enumaudio (so apps cannot
tell that audio inputs are present), it does not set V4L2_CAP_AUDIO, nor
does it set audioset when calling ENUM_INPUT. And G_AUDIO doesn't set the
stereo flag either. So these g/s_audio ioctls are quite pointless and
misleading. Especially since some surveillance boards do not have audio
at all.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 10 Feb 2013 12:24:14 +0000 (09:24 -0300)]
[media] bttv: do not switch to the radio tuner unless it is accessed
Just opening the radio tuner should not cause a switch to the radio tuner.
Only after calling g/s_tuner or g/s_frequency should this happen.
This prevents audio being unmuted as soon as the driver is loaded because
some process opens /dev/radioX just to see what sort of node it is, which
switches on the radio tuner and unmutes audio.
This code can be improved further by actually keeping track of who owns the
tuner and returning -EBUSY if switching tuner modes will cause problems.
But for now just fix the annoying case where on boot the radio turns on
automatically.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 7 Feb 2013 10:56:11 +0000 (07:56 -0300)]
[media] bttv: fix try_fmt_vid_overlay and setup initial overlay size
try_fmt_vid_overlay should map incorrect sizes and fields to valid values.
It also expects that an initial overlay size is defined so g_fmt_vid_overlay
returns valid information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 6 Feb 2013 15:43:37 +0000 (12:43 -0300)]
[media] bttv: there may be multiple tvaudio/tda7432 devices
Probe for additional tvaudio devices, and allow tvaudio+tda7432 to
co-exist. My STB TV PCI FM bttv card has a tda7432, a tda9850 and a
tea6420 and with this patch it finally works again (probably for the
first time in many years).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 6 Feb 2013 15:40:28 +0000 (12:40 -0300)]
[media] bttv: convert to the control framework
Note that the private chroma agc control has been replaced with the standard
CHROMA_AGC control.
Also fixes a mute/automute problem where closing the file handle would force
mute on. That's not what you want since that would make the mute state out of
sync with the mute control. Instead check against the user count.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 6 Feb 2013 15:03:30 +0000 (12:03 -0300)]
[media] bttv: fix field handling inside TRY_FMT
- don't return -EINVAL for invalid field types, handle those as if it
was FIELD_ANY.
- the handling of FIELD_SEQ_BT/TB was wrong as well: if such field formats
aren't supported, then fall back to FIELD_ANY instead of returning an error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 6 Feb 2013 14:43:07 +0000 (11:43 -0300)]
[media] bttv: disable g/s_tuner and g/s_freq when no tuner present, fix return codes
If no tuner is present, then disable the tuner and frequency ioctls.
We can remove a number of checks from those ioctls testing for the presence
of a tuner.
Also remove some tuner type checks (now done by the core) and fix an
error return when the prio check fails.
Finally some 'unlikely' statements are removed since those only make sense
in tightly often executed loops, otherwise they just clutter up the code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Sun, 9 Sep 2012 12:03:29 +0000 (09:03 -0300)]
[media] bttv: fix querycap and radio v4l2-compliance issues
The querycap ioctl didn't support V4L2_CAP_DEVICE_CAPS and the radio device
implemented audio and video inputs and s_std, which are not part of the radio
API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 7 Feb 2013 12:26:14 +0000 (09:26 -0300)]
[media] tlg2300: update MAINTAINERS file
Remove two maintainers: telegent.com no longer exists, so those email
addresses are invalid as well.
Added myself as co-maintainer and change the status to 'Odd Fixes'.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Thu, 31 Jan 2013 09:27:37 +0000 (06:27 -0300)]
[media] tlg2300: fix frequency handling
The usual set of problems: the frequency isn't clamped to the frequency range,
no tuner index check and the frequency isn't initialized properly on module
load.
Hans Verkuil [Thu, 12 Jul 2012 15:33:41 +0000 (12:33 -0300)]
[media] tlg2300: fix tuner and frequency handling of the radio device
This driver now passes the tuner and frequency tests of v4l2-compliance.
It's the usual bugs: frequency wasn't clamped to the valid frequency range,
incorrect tuner capabilities and tuner fields not filled in, missing test
for invalid tuner index, no initial frequency and incorrect error handling.
Hans Verkuil [Thu, 7 Feb 2013 12:31:33 +0000 (09:31 -0300)]
[media] tlg2300: use correct device parent
Set the correct parent for v4l2_device_register and don't set the name
anymore (that's now deduced from the parent). Also remove an unnecessary
forward reference and fix two weird looking log messages.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] em28xx-dvb: Don't put device in suspend mode at feed stop
Putting em28xx in suspend mode when a feed stops is just plain
wrong. Every time a new PES filter is changed, the DVB demux
code will stop the current feed, and then start a new one.
If are there any code that switches off the frontend, via
some GPIO setting, this would make the DVB fail.
This condition was actually trigged with one device, during
DVB scan, as, during scan, it is common that userspace apps
to change the filter several times, in order to get all
tables.
Also, this is not needed at all, since the em28xx code already
hooks into ops.ts_bus_ctrl(). This warrants that em28xx can
check there if DVB frontend is in usage or not. The code there
already puts the device on suspend mode, if the DVB frontend
is not used (closed).
[media] cx231xx: Improve signal reception for PV SBTVD
Instead of using 3.3 MHz IF, use 4MHz. That's the standard
value for the demod, and, while it can be adjusted, 3.3 MHz
is out of the recommended range. So, let's stick with the
default.
With regards to the IF voltage level, instead of using
0.5 V(p-p) for IF, use 2V, giving a 12dB gain.
The rationale is that, on PixelView SBTVD Hybrid,
even 2V(p-p) would be in the nominal range for IF,
as the maximum range on this particular device is 3V.
A higher gain here should help to improve reception under
weak signals.
[media] mb86a20s: Always reset the frontend with set_frontend
Always init the frontend when set_frontend is called. The rationale
is: it was noticed that, on some devices, it fails to lock with a
different channel. It seems that some other registers need to be
restored to its initial state, when the channel changes.
As it is better to reset everything, even wasting a few more
miliseconds than to loose channel lock, let's change the logic
to always reset.
Use the AGC settings present on a newer device.
The initial settings were taken from one of the first devices with
mb86a20s, and there are several reports that this is not working
properly on some places.
So, instead of keeping using it, get the parameters taken from a
newer device. Tests are welcomed.
Tested also with cx231xx PixelView SBTVD Hybrid with no regressions
noticed so far.
[media] mb86a20s: provide CNR stats before FE_HAS_SYNC
State 9 means TS started to be output, and it should be
associated with FE_HAS_SYNC.
The mb86a20scan get CNR statistics at state 7, when frame sync
is obtained.
As CNR may help to adjust the antenna, provide it earlier.
A latter patch could eventually start outputing MER measures
earlier, but that would require a bigger change, and probably
won't be better than the current way, as the time between
changing from state 8 to 9 is generally lower than the time
to get the stats collected.
Frank Schaefer [Sun, 3 Mar 2013 18:37:43 +0000 (15:37 -0300)]
[media] em28xx: extract the device configuration dataset from eeproms with 16 bit address width
The new eeproms with 16 address width still have the the device config dataset
(the content of the old 8 bit eeproms) embedded.
Hauppauge also continues to include the tveeprom data structure inside this
dataset in their devices.
The start address of the dataset depends on the start address of the microcode
and a variable additional offset.
It should be mentioned that Camera devices seem to use a different dataset type,
which is not yet supported.
Tested with devices "Hauppauge HVR-930C". I've also checked the USB-log from the
"MSI Digivox ATSC" and it works the same way.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer [Sun, 3 Mar 2013 18:37:42 +0000 (15:37 -0300)]
[media] em28xx: do not store eeprom content permanently
We currently reserve an array of 256 bytes for the eeprom content in the device
struct. For eeproms with 16 bit address width it might even be necessary to
increase the buffer size further.
Having such a big chunk of memory reserved even if the device has no eeprom and
keeping it after it has already been processed seems to be a waste of memory.
Change the code to allocate + free the eeprom memory dynamically.
This also makes it possible to handle different dataset sizes depending on what
is stored/found in the eeprom.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer [Sun, 3 Mar 2013 18:37:41 +0000 (15:37 -0300)]
[media] em28xx: add helper function for reading data blocks from i2c clients
Add a helper function for reading data blocks from i2c devices with 8 or 16 bit
address width and 8 bit register width.
This allows us to reduce the size of new code added by the following patches.
Works only for devices with activated register auto incrementation.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer [Sun, 3 Mar 2013 18:37:40 +0000 (15:37 -0300)]
[media] em28xx: add basic support for eeproms with 16 bit address width
Newer devices (em2874, em2884, em28174, em25xx, em27[6,7,8]x) use eeproms with
16 bit instead of 8 bit address width.
The used eeprom type depends on the chip type, which makes sure eeproms can't
be damaged.
This patch adds basic support for 16 bit eeproms only, which includes
- reading the content
- calculating the eeprom hash
- displaying the content
The eeprom content uses a different format, for which support will be added with
subsequent patches.
Tested with the "Hauppauge HVR-930C" and the "Speedlink VAD Laplace webcam"
(with additional experimental patches).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer [Sun, 3 Mar 2013 18:37:38 +0000 (15:37 -0300)]
[media] em28xx: fix eeprom data endianess
The data is stored as little endian in the eeprom.
Hence the correct data types should be used and the data should be converted
to the machine endianess before using it.
The eeprom id (key) also isn't a 32 bit value but 4 separate bytes instead.
Frank Schaefer [Sun, 3 Mar 2013 18:37:37 +0000 (15:37 -0300)]
[media] em28xx: do not interpret eeprom content if eeprom key is invalid
If the eeprom key isn't valid, either a different (currently unknown) format
is used or the eeprom is corrupted.
In both cases it doesn't make sense to interpret the data.
Also print an error message.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer [Sun, 3 Mar 2013 18:37:36 +0000 (15:37 -0300)]
[media] em28xx-i2c: also print debug messages at debug level 1
The current code uses only a single debug level and all debug messages are
printed for i2c_debug >= 2 only. So debug level 1 is actually the same as
level 0, which is odd.
Users expect debugging messages to become enabled for anything else than
debug level 0.
Fix it and simplify the code a bit by printing the debug messages also at debug
level 1;
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer [Sun, 3 Mar 2013 18:37:35 +0000 (15:37 -0300)]
[media] em28xx-i2c: get rid of the dprintk2 macro
There is only a single place where the dprintk2 macro is used, so get rid of it.
[mchehab@redhat.com: fix checkpathc.pl complain:
ERROR: space prohibited before that close parenthesis ')'] Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer [Mon, 11 Feb 2013 17:07:55 +0000 (14:07 -0300)]
[media] em28xx: bump driver version to 0.2.0
The em28xx driver has changed much, especially since kernel 3.8.
So it's time to bump the driver version.
Changes since kernel 3.8:
- converted the driver to videobuf2
- converted the driver to the v4l2-ctrl framework
- added USB bulk transfer support
- use USB bulk transfers by default for webcams (allows streaming from multiple devices at the same time)
- added image quality bridge controls: contrast, brightness, saturation, blue balance, red balance, sharpness
- removed dependency from module ir-kbd-i2c
- cleaned up the frame data processing code
- removed some unused/obsolete code
- made remote controls of devices with external (i2c) receiver/decoder work again
- fixed audio over USB for device "Terratec Cinergy 250"
- several v4l2 compliance fixes and improvements (including fixes for ioctls enabling/disabling)
- lots of further bug fixes and code improvements
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer [Fri, 15 Feb 2013 17:38:32 +0000 (14:38 -0300)]
[media] em28xx: add image quality bridge controls
Add the image quality bridge controls contrast, brightness, saturation,
blue balance, red balance and sharpness.
These controls are enabled only if no subdevice provides them.
Tested with the following devices:
"Terratec Cinergy 200 USB"
"Hauppauge HVR-900"
"SilverCrest 1.3MPix webcam"
"Hauppauge WinTV USB2"
"Speedlink VAD Laplace webcam"
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer [Sun, 10 Feb 2013 19:05:11 +0000 (16:05 -0300)]
[media] em28xx: introduce #define for maximum supported scaling values (register 0x30-0x33)
The maximum supported scaling value for registers 0x30+0x31 (horizontal scaling)
and 0x32+0x33 (vertical scaling) is 0x3fff, which corresponds to 20% of the
input frame size.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>