Arlin Davis [Wed, 16 May 2012 18:28:09 +0000 (11:28 -0700)]
Add configuration files for new Proxy RDMA/SCIF Provider
This proxy RDMA provider is a interbus service within a platform
to enable offloading of RDMA writes from a small core (MIC) to
large core resource. Data sourced on a MIC that is
destined for remote nodes on the fabric will be transfered
to large core via SCIF and than to remote node.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Wed, 25 Apr 2012 20:07:10 +0000 (13:07 -0700)]
config/build: remove post/postun hacking used to modify dat.conf
Return to the tried and true method of managing configuration
files via %config directive and remove ugly sed editing methods.
The dat.conf includes both v1 and v2 device entries to insure
backward compatibility. Add doc/dat.conf
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Fri, 20 Apr 2012 00:15:22 +0000 (17:15 -0700)]
commom: add cm, link, and diag event counters in IB extended builds
Add additional event monitoring capabilities during runtime to help
isolate issues during scaling in lieu of logging/printing warning
messages. Counters have been added to provider CM services and counters
have been added and mapped to sysfs ib_cm, device port and device
diag counters. ibdev_path is used for device sysfs counters.
uDAPL CM events are tracked on a per IA instance via internal
provider counters. The ib_cm, link, and diag events are tracked on a
per platform basis via sysfs. For these running counters a start
and stop function is provided for sampling and mapping to DAPL
64 bit counters. All counters, along with new start and stop functions,
are provided via dat_ib_extensions.h. New IB extension version is 2.0.7
New DCNT_IA_xx counters include 40 cm, 9 link, and 9 diag types.
To enable new counters (default build is disabled):
./configure --enable-counters
New bitmappings have been added to DAPL_DBG_TYPE environment
variable to automatically start/stop counters and log
errors if counters are enabled. The following will control
CM, LINK, and DIAG respectively:
Arlin Davis [Tue, 17 Apr 2012 22:24:22 +0000 (15:24 -0700)]
scm: use ioctl SIOCIFCONF to get complete list of configured netdev interfaces
replace usage of getaddrinfo since is doesnt actually return bound addresses
and can return the loopback address in some configurations. Some
systems may not have eth0 configured so you cannot assume eth0 as a non-loopback
default netdev.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Fri, 17 Feb 2012 18:28:48 +0000 (10:28 -0800)]
ucm: UD send failures at scale, ucm_send ERR: get_smsg(hd=149,tl=150)
Full sendq should retry polling completions instead of failing.
When sendq is full and all requests are pending the get send message
code should retry polling for completions and not return error on first
empty CQ attempt. Give HCA a chance to complete some batched requests.
Also, clean up the send message error logging.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Mon, 30 Jan 2012 18:19:29 +0000 (10:19 -0800)]
cma, scm, ucm: allow EP (QP) creation without EVD (CQ)
Provide ability to create a EP/QP with no EVD/CQ on either the
request or receive queue. The current implementation allows on
receive queue but not request queue. Not all ofa devices support
a null CQ so if necessary create a dummy CQ at the time of
QP creation. Also, if no CQ is specified set appropriate QP
max wr/sge attributes to zero.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Wed, 25 Jan 2012 19:50:21 +0000 (11:50 -0800)]
common: ep_create should allow max_request_iov attribute setting of zero
When creating an EP without a request EVD (cq) the max_request_iov
and max_request_sge will be 0. Allow this combination when checking
attribute settings for ARG6.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Thu, 12 Jan 2012 17:54:59 +0000 (09:54 -0800)]
common: extended CR event processing missing rejects on errors
When processing an inbound CR event callback a non-user reject should be
sent to client in the case of a non-listening SP, allocation error,
or EVD overrun. Changes made to dapls_evd_post_cr_event_ext callback.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Thu, 12 Jan 2012 17:39:46 +0000 (09:39 -0800)]
ucm: incorrectly sends user reject during CR callback errors
Add reason checking on provider rejects and set appropriate op type
in reject message. Reject can be called from cr callback during
failures. User reject will be IB_CM_REJ_REASON_CONSUMER_REJ.
Add warning message on active side.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Mon, 9 Jan 2012 23:03:21 +0000 (15:03 -0800)]
scm: incorrectly sends user reject during CR callback errors
Add reason checking on provider rejects and set appropriate op type
in reject message. Reject can be called from cr callback during
failures. User reject will be IB_CM_REJ_REASON_CONSUMER_REJ.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Thu, 8 Dec 2011 00:39:55 +0000 (16:39 -0800)]
cma,scm,ucm: extra reference on EP, with RSP, causes dat_ep_free() to hang
Need to add check for RSP or PSP provider type service points during
passive side accepts before taking CR reference on the EP. In these
cases, the EP is already linked to inbound CR.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Wed, 2 Nov 2011 17:29:34 +0000 (10:29 -0700)]
common: increase default IB ack timer from 16 to 20
For larger, more congested fabrics, a larger ACK timer is needed.
Consumers can still change default with environment variable
DAPL_ACK_TIMER if they need to increase or decrease.
This applies to SCM and UCM providers only. The CMA provider, which
uses rdma_cm, has no way to control ack timer with current API.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Mon, 24 Oct 2011 20:59:55 +0000 (13:59 -0700)]
scm: when hostname has loopback addr assigned, default to eth0 instead of failing
There are some cases where the eth0 device is configured with an IP address
but the getaddrinfo() will only return loopback address because the
hostname is configured in the /etc/hosts file with 127.0.0.1. In this case,
the provider will now retry address on eth0 before failing the open.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Mon, 24 Oct 2011 20:40:45 +0000 (13:40 -0700)]
common: query calls return incorrect IA handle to consumer
The IA handle from the consumer perspective is an IA vector and
not the provider IA address handle. Need to convert IA handle
to IA vector for consumer calls.
Modify dats_ia_get_handle call to convert both ways depending
on handle type provided so a dapl provider can convert to vector
on query calls. This fix is backward compatible with older libdat2
libraries. Function is already exported and syntax is unchanged.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Mon, 29 Aug 2011 02:10:37 +0000 (19:10 -0700)]
scm,ucm: fix compatibility issues and set minimum protocol support
allow latest version to work with previous versions to allow
compatibility back to OFED 1.5, dapl-2.0.23. If rdma_atomic_in
is not exchanged default back to original settings set by
consumer.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Fri, 19 Aug 2011 19:40:24 +0000 (12:40 -0700)]
build: add selective enable/disable-xxx build switch for each provider
The following switches have been added to configure:
--disable-cma (disables the rdma_cm dapl provider build)
--disable-scm (disables the socket cm provider build)
--disable-ucm (disables the IB UD cm provider build)
all providers are enabled by default.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
Arlin Davis [Mon, 8 Aug 2011 05:59:27 +0000 (22:59 -0700)]
build: add IB collective and FCA provider to dapl build package as an option
New collective support and the FCA provider will only be built with
configure option of "--enable-coll-type=fca". Dependencies include
fca devel package, fca library, and mverbs library. This will not
be included in default builds.
Signed-off-by: Arlin Davis <arlin.r.davis@intel.com>
projects / ~ardavis / dapl.git / log