[media] s5p-fimc: fimc-lite: Propagate frame format on the subdev
When setting image format on subdev's sink pad there was no
propagation to the source pad. This resulted in wrong reported
format on the source pad and wrong device configuration when
used from subdev interace level only. Correct this by propagating
format from the sink to the source pad.
Michael Krufky [Sat, 29 Sep 2012 19:06:23 +0000 (16:06 -0300)]
[media] tda18271: make 'low-power standby mode after attach' multi-instance safe
Ensure that unnecessary features are powered down at the end of the
attach() function on attach of the tuner's first instance. If the
configuration requires the loop thru or xtout features, they will
remain enabled.
This must *only* be done after attaching the first instance of the tuner.
If there are multiple instances of the tuner, the bridge driver will need
to maintain power managament by itself.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Krufky [Sat, 29 Sep 2012 19:05:26 +0000 (16:05 -0300)]
[media] tda18271: enter low-power standby mode at the end of tda18271_attach()
Ensure that unnecessary features are powered down at the end of the
attach() function. If the configuration requires the loop thru or
xtout features, they will remain enabled.
Thanks to Antti Palosaari for noticing the additional power consumption.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 5 Sep 2012 15:28:06 +0000 (12:28 -0300)]
[media] ivtv: disable a bunch of ioctls that are invalid for the decoder VBI
The VBI capture for the decoder (/dev/vbi8) is special in that it captures
the VBI stream embedded in an MPEG stream that is being decoded.
A lot of the ioctls that would normally be valid have to be disabled since
they make no sense for such a device, and v4l2-compliance will complain
about that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Mon, 1 Oct 2012 09:23:53 +0000 (06:23 -0300)]
[media] ivtv: fix v4l2-compliance errors for the radio device
- fix error code when attempting to read from write-only streams.
- fix error code when attempting to write to read-only streams.
- don't start capturing when polling on a radio node.
- give the radio node its own file operations struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner input has a different standard mask than a S-Video or Composite input.
Changing the standard should change tvnorms as well for all device nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 5 Sep 2012 11:39:48 +0000 (08:39 -0300)]
[media] ivtv: DECODER_CMD v4l2-compliance fixes
VIDIOC_DECODER_CMD didn't return EPERM when calling PAUSE or RESUME if no
decoding is in progress.
VIDIOC_G_ENC_INDEX didn't set entries_cap or return 0 if no decoding was
in progress.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Wed, 5 Sep 2012 13:38:10 +0000 (10:38 -0300)]
[media] sliced vbi: subdevs shouldn't clear the full v4l2_sliced_vbi_format struct
Various subdevs cleared the full v4l2_sliced_vbi_format struct, when
only the service_set/lines fields should have been cleared.
Due to this the io_size field was wrongly cleared to 0, causing a
v4l2-compliance error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil [Fri, 14 Sep 2012 10:15:03 +0000 (07:15 -0300)]
[media] v4l2-ctrls: add a filter function to v4l2_ctrl_add_handler
With a filter function you can control more precisely which controls
are added. This is useful in particular for radio device nodes for
combined TV/Radio cards where you want to show just the radio-specific
controls and not controls like brightness.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] fc2580: use macro for 64 bit division and reminder
Fixes the following warnings on a 32 bit system with GCC 4.4.3 and kernel Ubuntu 2.6.32-43 32 bit:
WARNING: "__udivdi3" [fc2580.ko] undefined!
WARNING: "__umoddi3" [fc2580.ko] undefined!
Signed-off-by: Gianluca Gennari <gennarone@gmail.com> Reviewed-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Arnd Bergmann [Wed, 22 Aug 2012 17:57:01 +0000 (14:57 -0300)]
[media] media/radio/shark2: Fix build error caused by missing dependencies
Without this patch, building rand-0y2jSKT results in:
WARNING: drivers/usb/musb/musb_hdrc.o(.devinit.text+0x9b8): Section mismatch in reference from the function musb_init_controller() to the function .init.text:dma_controller_create()
The function __devinit musb_init_controller() references
a function __init dma_controller_create().
If dma_controller_create is only used by musb_init_controller then
annotate dma_controller_create with a matching annotation.
[media] s5p-fimc: Fix setup of initial links to FIMC entities
This patch fixes regression introduced in commit 4af813108b880e96a4b8b01e162f950a4aaa2475. Missing pointers
to the sensor subdevs are restored along with subdev callback
notifications to a corresponding FIMC instance driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[media] s5p-fimc: Don't allocate fimc-m2m video device dynamically
There is no need to to dynamically allocate struct video_device
for the M2M devices, so embed it instead in driver's private
data structure as it is done in case of fimc-capture and fimc-lite,
where it solves some bugs on cleanup paths.
[media] s5p-fimc: Don't allocate fimc-lite video device structure dynamically
This fixes potential invalid pointer de-reference, when
media_entity_cleanup() is called after video_unregister_device,
and video device structure memory is already freed.
IBM reported a deadlock in select_parent(). This was found to be caused
by taking rename_lock when already locked when restarting the tree
traversal.
There are two cases when the traversal needs to be restarted:
1) concurrent d_move(); this can only happen when not already locked,
since taking rename_lock protects against concurrent d_move().
2) racing with final d_put() on child just at the moment of ascending
to parent; rename_lock doesn't protect against this rare race, so it
can happen when already locked.
Because of case 2, we need to be able to handle restarting the traversal
when rename_lock is already held. This patch fixes all three callers of
try_to_ascend().
IBM reported that the deadlock is gone with this patch.
[ I rewrote the patch to be smaller and just do the "goto again" if the
lock was already held, but credit goes to Miklos for the real work.
- Linus ]
Merge tag 'iommu-fixes-v3.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Two small patches:
* One patch to fix the function declarations for
!CONFIG_IOMMU_API. This is causing build errors
in linux-next and should be fixed for v3.6.
* Another patch to fix an IOMMU group related NULL pointer
dereference."
* tag 'iommu-fixes-v3.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix wrong assumption in iommu-group specific code
iommu: static inline iommu group stub functions
Pull NVMe driver fixes from Matthew Wilcox:
"Now that actual hardware has been released (don't have any yet
myself), people are starting to want some of these fixes merged."
Willy doesn't have hardware? Guys...
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Cancel outstanding IOs on queue deletion
NVMe: Free admin queue memory on initialisation failure
NVMe: Use ida for nvme device instance
NVMe: Fix whitespace damage in nvme_init
NVMe: handle allocation failure in nvme_map_user_pages()
NVMe: Fix uninitialized iod compiler warning
NVMe: Do not set IO queue depth beyond device max
NVMe: Set block queue max sectors
NVMe: use namespace id for nvme_get_features
NVMe: replace nvme_ns with nvme_dev for user admin
NVMe: Fix nvme module init when nvme_major is set
NVMe: Set request queue logical block size
Sasha Levin has been running trinity in a KVM tools guest, and was able
to trigger the BUG_ON() at arch/x86/mm/pat.c:279 (verifying the range of
the memory type). The call trace showed that it was mtdchar_mmap() that
created an invalid remap_pfn_range().
The problem is that mtdchar_mmap() does various really odd and subtle
things with the vma page offset etc, and uses the wrong types (and the
wrong overflow) detection for it.
For example, the page offset may well be 32-bit on a 32-bit
architecture, but after shifting it up by PAGE_SHIFT, we need to use a
potentially 64-bit resource_size_t to correctly hold the full value.
Also, we need to check that the vma length plus offset doesn't overflow
before we check that it is smaller than the length of the mtdmap region.
This fixes things up and tries to make the code a bit easier to read.
1) Netfilter xt_limit module can use uninitialized rules, from Jan
Engelhardt.
2) Wei Yongjun has found several more spots where error pointers were
treated as NULL/non-NULL and vice versa.
3) bnx2x was converted to pci_io{,un}map() but one remaining plain
iounmap() got missed. From Neil Horman.
4) Due to a fence-post type error in initialization of inetpeer entries
(which is where we store the ICMP rate limiting information), we can
erroneously drop ICMPs if the inetpeer was created right around when
jiffies wraps.
Fix from Nicolas Dichtel.
5) smsc75xx resume fix from Steve Glendinnig.
6) LAN87xx smsc chips need an explicit hardware init, from Marek Vasut.
7) qlcnic uses msleep() with locks held, fix from Narendra K.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netdev: octeon: fix return value check in octeon_mgmt_init_phy()
inetpeer: fix token initialization
qlcnic: Fix scheduling while atomic bug
bnx2: Clean up remaining iounmap
net: phy: smsc: Implement PHY config_init for LAN87xx
smsc75xx: fix resume after device reset
netdev: pasemi: fix return value check in pasemi_mac_phy_init()
team: fix return value check
l2tp: fix return value check
netfilter: xt_limit: have r->cost != 0 case work
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes; one for automount/lazy umount race, another a
classic "we don't protect the refcount transition to zero with the
lock that protects looking for object in hash" kind of crap in lockd."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
close the race in nlmsvc_free_block()
do_add_mount()/umount -l races
Merge branch 'for-linus-3.6-rc-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML fixes from Richard Weinberger.
* 'for-linus-3.6-rc-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Preinclude include/linux/kern_levels.h
um: Fix IPC on um
um: kill thread->forking
um: let signal_delivered() do SIGTRAP on singlestepping into handler
um: don't leak floating point state and segment registers on execve()
um: take cleaning singlestep to start_thread()
Merge tag 'dm-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull dm fixes from Alasdair G Kergon:
"A few fixes for problems discovered during the 3.6 cycle.
Of particular note, are fixes to the thin target's discard support,
which I hope is finally working correctly; and fixes for multipath
ioctls and device limits when there are no paths."
* tag 'dm-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm verity: fix overflow check
dm thin: fix discard support for data devices
dm thin: tidy discard support
dm: retain table limits when swapping to new table with no devices
dm table: clear add_random unless all devices have it set
dm: handle requests beyond end of device instead of using BUG_ON
dm mpath: only retry ioctl when no paths if queue_if_no_path set
dm thin: do not set discard_zeroes_data
Andrea Arcangeli [Fri, 28 Sep 2012 12:35:31 +0000 (14:35 +0200)]
thp: avoid VM_BUG_ON page_count(page) false positives in __collapse_huge_page_copy
Speculative cache pagecache lookups can elevate the refcount from
under us, so avoid the false positive. If the refcount is < 2 we'll be
notified by a VM_BUG_ON in put_page_testzero as there are two
put_page(src_page) in a row before returning from this function.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reviewed-by: Rik van Riel <riel@redhat.com> Reviewed-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Hugh Dickins <hughd@google.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Petr Holasek <pholasek@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
iommu/amd: Fix wrong assumption in iommu-group specific code
The new IOMMU groups code in the AMD IOMMU driver makes the
assumption that there is a pci_dev struct available for all
device-ids listed in the IVRS ACPI table. Unfortunatly this
assumption is not true and so this code causes a NULL
pointer dereference at boot on some systems.
Fix it by making sure the given pointer is never NULL when
passed to the group specific code. The real fix is larger
and will be queued for v3.7.
netdev: octeon: fix return value check in octeon_mgmt_init_phy()
In case of error, the function of_phy_connect() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"The three nouveau fixes quiten unneeded dmesg spam that people are
seeing and pondering,
The udl fix stops it from trying to driver monitors that are too big,
where we get a black screen.
And a vmware memory alloc problem."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nvc0/fifo: ignore bits in PFIFO_INTR that aren't set in PFIFO_INTR_EN
drm/udl: limit modes to the sku pixel limits.
vmwgfx: corruption in vmw_event_fence_action_create()
drm/nvc0/ltcg: mask off intr 0x10
drm/nouveau: silence a debug message triggered by newer userspace
Merge tag 'usb-3.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are two USB bugfixes for your 3.6-rc7 tree.
The OHCI fix has been reported a number of times and is a regression
from 3.5, and the patch that causes the regression was on the way to
the -stable trees before I was reminded (again) that this fix needed
to get to your tree soon.
The host controller bugfix was reported in older kernels as being
pretty easy to trigger, and has been tested by Red Hat and their
customers.
Both have been in the usb-next branch in the -next tree for a while
now, I just cherry-picked them out to get to you in time for the 3.6
release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: Fix race condition when removing host controllers
USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq
Nicolas Dichtel [Thu, 27 Sep 2012 04:11:00 +0000 (04:11 +0000)]
inetpeer: fix token initialization
When jiffies wraps around (for example, 5 minutes after the boot, see
INITIAL_JIFFIES) and peer has just been created, now - peer->rate_last can be
< XRLIM_BURST_FACTOR * timeout, so token is not set to the maximum value, thus
some icmp packets can be unexpectedly dropped.
Fix this case by initializing last_rate to 60 seconds in the past.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Narendra K [Tue, 25 Sep 2012 07:53:19 +0000 (07:53 +0000)]
qlcnic: Fix scheduling while atomic bug
In the device close path, 'qlcnic_fw_destroy_ctx' and
'qlcnic_poll_rsp' call msleep. But 'qlcnic_fw_destroy_ctx' and
'qlcnic_poll_rsp' are called with 'adapter->tx_clean_lock' spin lock
held resulting in scheduling while atomic bug causing the following
trace.
I observed that the commit 012dc19a45b2b9cc2ebd14aaa401cf782c2abba4
from John Fastabend addresses a similar issue in ixgbevf driver.
Adopting the same approach used in the commit, this patch uses mdelay
to address the issue.
Neil Horman [Wed, 26 Sep 2012 07:22:02 +0000 (07:22 +0000)]
bnx2: Clean up remaining iounmap
commit c0357e975afdbbedab5c662d19bef865f02adc17 modified bnx2 to switch from
using ioremap/iounmap to pci_iomap/pci_iounmap. They missed a spot in the error
path of bnx2_init_one though. This patch just cleans that up.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Michael Chan <mcan@broadcom.com> CC: "David S. Miller" <davem@davemloft.net> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull one more arm-soc bugfix from Olof Johansson:
"Here's a bugfix for orion5x. Without this, PCI doesn't initialize
properly because of too small coherent pool to cover the allocations
needed.
A similar fix has already been done on kirkwood."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion5x: Fix too small coherent pool.
Merge tag 'gpio-fixes-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"A late GPIO fix: Roland Stigge found a problem in the LPC32xx driver
where a callback ignores one of its arguments. It needs to go into
stable too so sending this upstream immediately."
* tag 'gpio-fixes-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio-lpc32xx: Fix value handling of gpio_direction_output()
Merge tag 'md-3.6-fixes' of git://neil.brown.name/md
Pull two md bugfixes from NeilBrown:
"One (missing spinlock init) was only introduced recently. The other
has been present as long as raid10 has been supported, so is tagged
for -stable."
* tag 'md-3.6-fixes' of git://neil.brown.name/md:
md/raid10: fix "enough" function for detecting if array is failed.
md/raid5: add missing spin_lock_init.
Pull EDAC fixes from Mauro Carvalho Chehab:
"Three edac fixes at the memory enumeration logic:
- i3200_edac: Fixes a regression at the memory rank size, when the
memorias are dual-rank;
- i5000_edac: Fix a longstanding bug when calculating the memory
size: before Kernel 3.6, the memory size were right only
with one specific configuration;
- sb_edac: Fixes a bug since the initial release of the driver:
with 16GB DIMMs, there's an overflow at the memory size,
causing the number of pages per dimm (an unsigned value)
to have the highest bit equal to 1, effectively mangling
the memory size.
The third bug can potentially affect the error decoding logic as well."
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
sb_edac: Avoid overflow errors at memory size calculation
i5000: Fix the memory size calculation with 2R memories
i3200_edac: Fix memory rank size
Marek Vasut [Tue, 25 Sep 2012 10:17:42 +0000 (10:17 +0000)]
net: phy: smsc: Implement PHY config_init for LAN87xx
The LAN8710/LAN8720 chips do have broken the "FlexPWR" smart power-saving
capability. Enabling it leads to the PHY not being able to detect Link when
cold-started without cable connected. Thus, make sure this is disabled.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Christian Hohnstaedt <chohnstaedt@innominate.com> Cc: David S. Miller <davem@davemloft.net> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: David S. Miller <davem@davemloft.net>
[media] media: mx2_camera: use managed functions to clean up code
Use managed functions to clean up the error handling code and function
mx2_camera_remove(). Along with the change, a few variables get removed
from struct mx2_camera_dev.
[media] media: mx2_camera: remove dead code in mx2_camera_add_device
This is a piece of code becoming dead since commit 2c9ba37 ([media]
V4L: mx2_camera: remove unsupported i.MX27 DMA mode, make EMMA
mandatory). It should have been removed together with the commit.
Remove it now.
The userspace part of UML uses the asm-offsets.h generator mechanism to
create definitions for UM_KERN_<LEVEL> that match the in-kernel
KERN_<LEVEL> constant definitions.
As of commit 04d2c8c83d0e3ac5f78aeede51babb3236200112 ("printk: convert
the format for KERN_<LEVEL> to a 2 byte pattern"), KERN_<LEVEL> is no
longer expanded to the literal '"<LEVEL>"', but to '"\001" "LEVEL"', i.e.
it contains two parts.
However, the combo of DEFINE_STR() in
arch/x86/um/shared/sysdep/kernel-offsets.h and sed-y in Kbuild doesn't
support string literals consisting of multiple parts. Hence for all
UM_KERN_<LEVEL> definitions, only the SOH character is retained in the actual
definition, while the remainder ends up in the comment. E.g. in
include/generated/asm-offsets.h we get
#define UM_KERN_INFO "\001" /* "6" KERN_INFO */
instead of
#define UM_KERN_INFO "\001" "6" /* KERN_INFO */
This causes spurious '^A' output in some kernel messages:
Calibrating delay loop... 4640.76 BogoMIPS (lpj=23203840)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 256
^AChecking that host ptys support output SIGIO...Yes
^AChecking that host ptys support SIGIO on close...No, enabling workaround
^AUsing 2.6 host AIO
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource itimer
To fix this:
- Move the mapping from UM_KERN_<LEVEL> to KERN_<LEVEL> from
arch/um/include/shared/common-offsets.h to
arch/um/include/shared/user.h, which is preincluded for all userspace
parts,
- Preinclude include/linux/kern_levels.h for all userspace parts, to
obtain the in-kernel KERN_<LEVEL> constant definitions. This doesn't
violate the kernel/userspace separation, as include/linux/kern_levels.h
is self-contained and doesn't expose any other kernel internals.
- Remove the now unused STR() and DEFINE_STR() macros.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Richard Weinberger <richard@nod.at>
Refactor firmware download function. It also should fix one bug
coming from usb_control_msg() message buffers. Taking buffers from
the stack for usb_control_msg() is not allowed as it does not work
on all architectures. Allocate buffers using kmalloc().
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is 4 x RTL2832U + 4 x FC0012 in one PCIe board.
Of course there is a PCIe USB host controller too.
Big thanks for Darryl Bond reporting and testing that!
Reported-by: Darryl Bond <darryl.bond@gmail.com> Tested-by: Darryl Bond <darryl.bond@gmail.com> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Oliver Schinagl [Thu, 20 Sep 2012 17:57:17 +0000 (14:57 -0300)]
[media] Support for Asus MyCinema U3100Mini Plus
This is initial support for the Asus MyCinema U3100Mini Plus. The driver
in its current form gets detected and loads properly.
Scanning using dvbscan works without problems, Locking onto a channel
using tzap also works fine. Only playback using tzap -r + mplayer was
tested and was fully functional.
It uses the af9035 USB Bridge chip, with an af9033 demodulator. The tuner
used is the FCI FC2580.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Mon, 17 Sep 2012 18:49:54 +0000 (15:49 -0300)]
[media] rtl28xxu: do not return error for unimplemented fe callback
Use of frontend callback is highly hardware design dependent
and whole callback could be optional in many cases. Returning
error by default when callback is not implemented is stupid.
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Tue, 11 Sep 2012 01:04:43 +0000 (22:04 -0300)]
[media] dvb_usb_v2: call streaming_ctrl() before kill urbs
Logically it is better ask hardware to stop streaming before
killing urbs carrying stream. Earlier it was just opposite.
Now code runs:
* submit urbs
* start streaming
** streaming ongoing **
* stop streaming
* kill urbs
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit c1d7e01d (ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION)
forgot UML and broke IPC on it.
Also UML has to select ARCH_WANT_IPC_PARSE_VERSION usin Kconfig.
Reported-and-tested-by: <Toralf Förster toralf.foerster@gmx.de> Signed-off-by: Richard Weinberger <richard@nod.at>
netdev: pasemi: fix return value check in pasemi_mac_phy_init()
In case of error, the function of_phy_connect() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
[media] omap3isp: Fix error return code in probe function
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
[laurent.pinchart@ideasonboard.com Replaced EBUSY with ENODEV] Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In case of error, the function genlmsg_put() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function genlmsg_put() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Stern [Wed, 26 Sep 2012 17:09:53 +0000 (13:09 -0400)]
USB: Fix race condition when removing host controllers
This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.
The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered. The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated. As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.
The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times. It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Don Zickus <dzickus@redhat.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6fffb77c (USB: ohci-at91: fix PIO handling in relation with number of
ports) started setting unused pins to EINVAL. But this exposed a bug in the
ohci_hcd_at91_overcurrent_irq function where the gpio was used without being
checked to see if it is valid.
This patches fixed the issue by adding the gpio valid check.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com> Cc: stable <stable@vger.kernel.org> # [3.4+] whereever 6fffb77c went Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Thu, 20 Sep 2012 13:28:25 +0000 (09:28 -0400)]
um: kill thread->forking
we only use that to tell copy_thread() done by syscall from that
done by kernel_thread(). However, it's easier to do simply by
checking PF_KTHREAD in thread flags.
Merge sys_clone() guts for 32bit and 64bit, while we are at it...