Linus Torvalds [Sat, 4 Feb 2012 15:17:47 +0000 (07:17 -0800)]
Merge tag 'for-linus-3.3' of git://git.infradead.org/~dwmw2/mtd-3.3
- Fix a regression in 16-bit Atmel NAND flash which was introduced in 3.1
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
* tag 'for-linus-3.3-20120204' of git://git.infradead.org/~dwmw2/mtd-3.3:
Revert "mtd: atmel_nand: optimize read/write buffer functions"
mtd: fix MTD suspend
jffs2: do not initialize variable unnecessarily
mtd: gpmi-nand bugfix: reset the BCH module when it is not MX23
mtd: nand: fix typo in comment
Nicolas Ferre <nicolas.ferre@atmel.com> alco confirmed:
"After double checking with designers, I must admit that I misunderstood
the way of optimizing accesses to SMC. 16 bit nand is not so common
those days..."
Reported-by: Nikolaus Voss <n.voss@weinmann.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Cc: stable@kernel.org [3.1+]
Mel Gorman [Fri, 3 Feb 2012 23:37:18 +0000 (15:37 -0800)]
mm: compaction: check pfn_valid when entering a new MAX_ORDER_NR_PAGES block during isolation for migration
When isolating for migration, migration starts at the start of a zone
which is not necessarily pageblock aligned. Further, it stops isolating
when COMPACT_CLUSTER_MAX pages are isolated so migrate_pfn is generally
not aligned. This allows isolate_migratepages() to call pfn_to_page() on
an invalid PFN which can result in a crash. This was originally reported
against a 3.0-based kernel with the following trace in a crash dump.
The migrate_pfn is just below a memory hole and the free scanner is beyond
the hole. When isolate_migratepages started, it scans from migrate_pfn to
migrate_pfn+pageblock_nr_pages which is now in a memory hole. It checks
pfn_valid() on the first PFN but then scans into the hole where there are
not necessarily valid struct pages.
This patch ensures that isolate_migratepages calls pfn_valid when
necessary.
Reported-by: Herbert van den Bergh <herbert.van.den.bergh@oracle.com> Tested-by: Herbert van den Bergh <herbert.van.den.bergh@oracle.com> Signed-off-by: Mel Gorman <mgorman@suse.de> Acked-by: Michal Nazarewicz <mina86@mina86.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shaohua Li [Fri, 3 Feb 2012 23:37:17 +0000 (15:37 -0800)]
readahead: fix pipeline break caused by block plug
Herbert Poetzl reported a performance regression since 2.6.39. The test
is a simple dd read, but with big block size. The reason is:
T1: ra (A, A+128k), (A+128k, A+256k)
T2: lock_page for page A, submit the 256k
T3: hit page A+128K, ra (A+256k, A+384). the range isn't submitted
because of plug and there isn't any lock_page till we hit page A+256k
because all pages from A to A+256k is in memory
T4: hit page A+256k, ra (A+384, A+ 512). Because of plug, the range isn't
submitted again.
T5: lock_page A+256k, so (A+256k, A+512k) will be submitted. The task is
waitting for (A+256k, A+512k) finish.
There is no request to disk in T3 and T4, so readahead pipeline breaks.
We really don't need block plug for generic_file_aio_read() for buffered
I/O. The readahead already has plug and has fine grained control when I/O
should be submitted. Deleting plug for buffered I/O fixes the regression.
One side effect is plug makes the request size 256k, the size is 128k
without it. This is because default ra size is 128k and not a reason we
need plug here.
Vivek said:
: We submit some readahead IO to device request queue but because of nested
: plug, queue never gets unplugged. When read logic reaches a page which is
: not in page cache, it waits for page to be read from the disk
: (lock_page_killable()) and that time we flush the plug list.
:
: So effectively read ahead logic is kind of broken in parts because of
: nested plugging. Removing top level plug (generic_file_aio_read()) for
: buffered reads, will allow unplugging queue earlier for readahead.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Reported-by: Herbert Poetzl <herbert@13thfloor.at> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiang Liu [Fri, 3 Feb 2012 23:37:16 +0000 (15:37 -0800)]
kprobes: fix a memory leak in function pre_handler_kretprobe()
In function pre_handler_kretprobe(), the allocated kretprobe_instance
object will get leaked if the entry_handler callback returns non-zero.
This may cause all the preallocated kretprobe_instance objects exhausted.
This issue can be reproduced by changing
samples/kprobes/kretprobe_example.c to probe "mutex_unlock". And the fix
is straightforward: just put the allocated kretprobe_instance object back
onto the free_instances list.
[akpm@linux-foundation.org: use raw_spin_lock/unlock] Signed-off-by: Jiang Liu <jiang.liu@huawei.com> Acked-by: Jim Keniston <jkenisto@us.ibm.com> Acked-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carsten Otte [Fri, 3 Feb 2012 23:37:14 +0000 (15:37 -0800)]
mm/filemap_xip.c: fix race condition in xip_file_fault()
Fix a race condition that shows in conjunction with xip_file_fault() when
two threads of the same user process fault on the same memory page.
In this case, the race winner will install the page table entry and the
unlucky loser will cause an oops: xip_file_fault calls vm_insert_pfn (via
vm_insert_mixed) which drops out at this check:
retval = -EBUSY;
if (!pte_none(*pte))
goto out_unlock;
The resulting -EBUSY return value will trigger a BUG_ON() in
xip_file_fault.
This fix simply considers the fault as fixed in this case, because the
race winner has successfully installed the pte.
[akpm@linux-foundation.org: use conventional (and consistent) comment layout] Reported-by: David Sadler <dsadler@us.ibm.com> Signed-off-by: Carsten Otte <cotte@de.ibm.com> Reported-by: Louis Alex Eisner <leisner@cs.ucsd.edu> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fabio Baltieri [Fri, 3 Feb 2012 23:37:14 +0000 (15:37 -0800)]
avr32: select generic atomic64_t support
Enable use of the generic atomic64 implementation on AVR32 platforms.
Without this the kernel fails to build as the architecture does not
provide its version.
Postpone resetting page->mapping until the final remove_migration_ptes().
Otherwise the expression PageAnon(migration_entry_to_page(entry)) does not
work.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Hugh Dickins <hughd@google.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Fri, 3 Feb 2012 23:37:13 +0000 (15:37 -0800)]
xtensa: fix memscan()
Defining memscan() as memchr() is wrong, because the return values of
memscan() and memchr() are different when the character is not found. So
use the generic memscan() implementation to fix this.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Chris Zankel <chris@zankel.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 3 Feb 2012 20:41:31 +0000 (12:41 -0800)]
Merge tag 'kmemleak-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux
Trivial kmemleak bug-fixes:
- Early logging doesn't stop when kmemleak is off by default.
- Zero-size scanning areas should be ignored (currently it prints a
warning).
* tag 'kmemleak-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux:
kmemleak: Disable early logging when kmemleak is off by default
kmemleak: Only scan non-zero-size areas
Linus Torvalds [Fri, 3 Feb 2012 18:06:15 +0000 (10:06 -0800)]
Merge tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
sound fixes for 3.3-rc3
Most of commits are either regression fixes for varioud HD-audio
codecs or small ASoC fixes. Also a trivial build fix is included.
* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Disable dynamic-power control for VIA as default
ALSA: hda - Allow analog low-current mode when dynamic power-control is on
ALSA: hda - Fix the logic to detect VIA analog low-current mode
ALSA: hda - Check power-state before changing in patch_via.c
ALSA: HDA: Fix duplicated output to more than one codec
ALSA: hda - Fix calling cs_automic twice for Cirrus codecs.
ALSA: HDA: Remove quirk for Toshiba Qosmio G50
ALSA: HDA: Fix jack creation for codecs with front and rear Line In
ALSA: hda - Apply 0x0f-VREF fix to all ASUS laptops with ALC861/660
ASoC: neo1973_wm8753: remove references to the neo1973-gta01 machine
ALSA: Add #ifdef CONFIG_PCI guard for snd_pci_quirk_* functions
ASoC: wm_hubs: fix wrong bits for LINEOUT2 N/P mixer
ALSA: HDA: Remove quirk for Asus N53Jq
ASoC: wm_hubs: Enable line out VMID buffer for single ended line outputs
ASoC: wm5100: Mark register cache as dirty when regulators are disabled
ASoC: wm8962: Mark register cache as dirty when regulators are disabled
ASoC: wm8996: Mark register cache as dirty when regulators are disabled
ASoC: wm5100: Fix microphone configuration
ASoC: wm5100: Make sure we switch to button reporting mode
Will Deacon [Fri, 3 Feb 2012 10:08:05 +0000 (11:08 +0100)]
ARM: 7314/1: kuser: consistently use usr_ret for returning from helpers
__kuser_cmpxchg64 has a return path using bx lr to get back to the caller.
This is actually ok since the code in question is predicated on
CONFIG_CPU_32v6K, but for the sake of consistency using the usr_ret
macro is probably better.
Acked-by: Dave Martin <dave.martin@linaro.org> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Thu, 2 Feb 2012 23:47:33 +0000 (15:47 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: fix safety of rbd_put_client()
rbd: fix a memory leak in rbd_get_client()
ceph: create a new session lock to avoid lock inversion
ceph: fix length validation in parse_reply_info()
ceph: initialize client debugfs outside of monc->mutex
ceph: change "ceph.layout" xattr to be "ceph.file.layout"
Alex Elder [Sun, 29 Jan 2012 19:57:43 +0000 (13:57 -0600)]
rbd: fix safety of rbd_put_client()
The rbd_client structure uses a kref to arrange for cleaning up and
freeing an instance when its last reference is dropped. The cleanup
routine is rbd_client_release(), and one of the things it does is
delete the rbd_client from rbd_client_list. It acquires node_lock
to do so, but the way it is done is still not safe.
The problem is that when attempting to reuse an existing rbd_client,
the structure found might already be in the process of getting
destroyed and cleaned up.
Here's the scenario, with "CLIENT" representing an existing
rbd_client that's involved in the race:
Thread on CPU A | Thread on CPU B
--------------- | ---------------
rbd_put_client(CLIENT) | rbd_get_client()
kref_put() | (acquires node_lock)
kref->refcount becomes 0 | __rbd_client_find() returns CLIENT
calls rbd_client_release() | kref_get(&CLIENT->kref);
| (releases node_lock)
(acquires node_lock) |
deletes CLIENT from list | ...and starts using CLIENT...
(releases node_lock) |
and frees CLIENT | <-- but CLIENT gets freed here
Fix this by having rbd_put_client() acquire node_lock. The result
could still be improved, but at least it avoids this problem.
Signed-off-by: Alex Elder <elder@dreamhost.com> Signed-off-by: Sage Weil <sage@newdream.net>
This has been updated since I last sent it as the creation of the new
mm_access() function did almost exactly the same thing as parts of the
previous version of this patch did.
In order to use mm_access() even when /proc isn't enabled, we move it to
kernel/fork.c where other related process mm access functions already
are.
Signed-off-by: Chris Yeoh <yeohc@au1.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Elder [Fri, 13 Jan 2012 01:48:10 +0000 (17:48 -0800)]
ceph: create a new session lock to avoid lock inversion
Lockdep was reporting a possible circular lock dependency in
dentry_lease_is_valid(). That function needs to sample the
session's s_cap_gen and and s_cap_ttl fields coherently, but needs
to do so while holding a dentry lock. The s_cap_lock field was
being used to protect the two fields, but that can't be taken while
holding a lock on a dentry within the session.
In most cases, the s_cap_gen and s_cap_ttl fields only get operated
on separately. But in three cases they need to be updated together.
Implement a new lock to protect the spots updating both fields
atomically is required.
Signed-off-by: Alex Elder <elder@dreamhost.com> Reviewed-by: Sage Weil <sage@newdream.net>
Xi Wang [Sun, 15 Jan 2012 03:20:59 +0000 (22:20 -0500)]
ceph: fix length validation in parse_reply_info()
"len" is read from network and thus needs validation. Otherwise, given
a bogus "len" value, p+len could be an out-of-bounds pointer, which is
used in further parsing.
Signed-off-by: Xi Wang <xi.wang@gmail.com> Signed-off-by: Sage Weil <sage@newdream.net>
Sage Weil [Sat, 14 Jan 2012 06:22:03 +0000 (22:22 -0800)]
ceph: initialize client debugfs outside of monc->mutex
Initializing debufs under monc->mutex introduces a lock dependency for
sb->s_type->i_mutex_key, which (combined with several other dependencies)
leads to an annoying lockdep warning. There's no particular reason to do
the debugfs setup under this lock, so move it out.
It used to be the case that our first monmap could come from the OSD; that
is no longer the case with recent servers, so we will reliably set up the
client entry during the initial authentication.
We don't have to worry about racing with debugfs teardown by
ceph_debugfs_client_cleanup() because ceph_destroy_client() calls
ceph_msgr_flush() first, which will wait for the message dispatch work
to complete (and the debugfs init to complete).
Fixes: #1940 Signed-off-by: Sage Weil <sage@newdream.net>
Alex Elder [Thu, 12 Jan 2012 01:41:01 +0000 (17:41 -0800)]
ceph: change "ceph.layout" xattr to be "ceph.file.layout"
The virtual extended attribute named "ceph.layout" is meaningful
only for regular files. Change its name to be "ceph.file.layout" to
more directly reflect that in the ceph xattr namespace. Preserve
the old "ceph.layout" name for the time being (until we decide it's
safe to get rid of it entirely).
Add a missing initializer for "readonly" in the terminating entry.
Signed-off-by: Alex Elder <elder@dreamhost.com> Reviewed-by: Sage Weil <sage@newdream.net>
Linus Torvalds [Thu, 2 Feb 2012 19:19:03 +0000 (11:19 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/blit: fix blit copy for very large buffers
drm/radeon/kms: fix TRAVIS panel setup
drm/radeon: fix use after free in ATRM bios reading code.
drm/radeon/kms: Fix device tree linkage of DP i2c buses too
drm/radeon: Set DESKTOP_HEIGHT register to the framebuffer (not mode) height.
drm/radeon/kms: disable output polling when suspended
drm/nv50/pm: signedness bug in nv50_pm_clocks_pre()
drm/nouveau/gem: fix fence_sync race / oops
drm/nouveau: fix typo on mxmdcb option
drm/nouveau/mxm: pretend to succeed, even if we can't shadow the MXM-SIS
drm/nouveau/disp: check that panel power gpio is enabled at init time
Linus Torvalds [Thu, 2 Feb 2012 19:11:13 +0000 (11:11 -0800)]
Merge branches 'core-urgent-for-linus', 'perf-urgent-for-linus', 'sched-urgent-for-linus' and 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
bugs, x86: Fix printk levels for panic, softlockups and stack dumps
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf top: Fix number of samples displayed
perf tools: Fix strlen() bug in perf_event__synthesize_event_type()
perf tools: Fix broken build by defining _GNU_SOURCE in Makefile
x86/dumpstack: Remove unneeded check in dump_trace()
perf: Fix broken interrupt rate throttling
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/rt: Fix task stack corruption under __ARCH_WANT_INTERRUPTS_ON_CTXSW
sched: Fix ancient race in do_exit()
sched/nohz: Fix nohz cpu idle load balancing state with cpu hotplug
sched/s390: Fix compile error in sched/core.c
sched: Fix rq->nr_uninterruptible update race
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/reboot: Remove VersaLogic Menlow reboot quirk
x86/reboot: Skip DMI checks if reboot set by user
x86: Properly parenthesize cmpxchg() macro arguments
Catalin Marinas [Wed, 25 Jan 2012 10:54:22 +0000 (11:54 +0100)]
ARM: 7302/1: Add TLB flushing for both entries in a PMD
Linux uses two PMD entries for a PTE with the classic page table format,
covering 2MB range. However, the __pte_free_tlb() function only adds a
single TLB flush corresponding to 1MB range covering 'addr'. On
Cortex-A15, level 1 entries can be cached by the TLB independently of
the level 2 entries and without additional flushing a PMD entry would be
left pointing at the wrong PTE. The patch limits the TLB flushing range
to two 4KB pages around the 1MB boundary within PMD.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Wed, 25 Jan 2012 18:36:28 +0000 (19:36 +0100)]
ARM: 7303/1: perf: add empty NODE event definitions for Cortex-A5 and Cortex-A15
Commit 89d6c0b5 ("perf, arch: Add generic NODE cache events") added
empty NODE event definitions for the ARM PMU implementations. This was
merged along with Cortex-A5 and Cortex-A15 PMU support, so they missed
out on the original patch.
This patch adds the empty definitions to Cortex-A5 and Cortex-A15.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Mon, 30 Jan 2012 19:23:29 +0000 (20:23 +0100)]
ARM: 7308/1: vfp: flush thread hwstate before copying ptrace registers
If we are context switched whilst copying into a thread's
vfp_hard_struct then the partial copy may be corrupted by the VFP
context switching code (see "ARM: vfp: flush thread hwstate before
restoring context from sigframe").
This patch updates the ptrace VFP set code so that the thread state is
flushed before the copy, therefore disabling VFP and preventing
corruption from occurring.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In a preemptible kernel, vfp_set() can be preempted, causing the
hardware VFP context to be switched while the thread vfp state is
being read and modified. This leads to a race condition which can
cause the thread vfp state to become corrupted if lazy VFP context
save occurs due to preemption in between the time thread->vfpstate
is read and the time the modified state is written back.
This may occur if preemption occurs during the execution of a
ptrace() call which modifies the VFP register state of a thread.
Such instances should be very rare in most realistic scenarios --
none has been reported, so far as I am aware. Only uniprocessor
systems should be affected, since VFP context save is not currently
lazy in SMP kernels.
The problem was introduced by my earlier patch migrating to use
regsets to implement ptrace.
This patch does a vfp_sync_hwstate() before reading
thread->vfpstate, to make sure that the thread's VFP state is not
live in the hardware registers while the registers are modified.
Thanks to Will Deacon for spotting this.
Cc: stable <stable@vger.kernel.org> Signed-off-by: Dave Martin <dave.martin@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Will Deacon [Mon, 30 Jan 2012 19:21:42 +0000 (20:21 +0100)]
ARM: 7306/1: vfp: flush thread hwstate before restoring context from sigframe
Following execution of a signal handler, we currently restore the VFP
context from the ucontext in the signal frame. This involves copying
from the user stack into the current thread's vfp_hard_struct and then
flushing the new data out to the hardware registers.
This is problematic when using a preemptible kernel because we could be
context switched whilst updating the vfp_hard_struct. If the current
thread has made use of VFP since the last context switch, the VFP
notifier will copy from the hardware registers into the vfp_hard_struct,
overwriting any data that had been partially copied by the signal code.
Disabling preemption across copy_from_user calls is a terrible idea, so
instead we move the VFP thread flush *before* we update the
vfp_hard_struct. Since the flushing is performed lazily, this has the
effect of disabling VFP and clearing the CPU's VFP state pointer,
therefore preventing the thread from being updated with stale data on
the next context switch.
Cc: stable <stable@vger.kernel.org> Tested-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Joachim Eastwood reports:
| "ARM: 7304/1: ioremap: fix boundary check when reusing static mapping"
| Commit: 3c424f359898aff48c3d5bed608ac706f8a528c3 in Linus master
|
| Breaks booting on my custom AT91RM9200 board.
| There isn't any error messages or anything that indicates what goes
| wrong it just stops after; Uncompressing Linux... done, booting the
| kernel.
|
| Reverting it makes my board boot again.
Clearly, an area for pfn 0x200, 16K can't ever satisfy a request for pfn
0xfffff. This happens because the changed if statement becomes:
if (0x00200 > 0xfffff ||
0xfffff000 + 0x400 + 0x1000-1 > 0x00200000 + 0x4000-1)
and therefore:
if (0x00200 > 0xfffff ||
0x000003ff > 0x00203fff)
The if condition fails, and so we _believe_ that the SRAM mapping fits
our request. Clearly that's totally bogus.
Moreover, the original premise of the 'fix' patch was wrong:
| The condition checking boundaries of the requested and existing
| mappings didn't take in-page offset into consideration though,
| which lead to obscure and hard to debug problems when requested
| mapping crossed end of the static one.
as the code immediately above this loop does:
size = PAGE_ALIGN(offset + size);
so 'size' already contains the requested offset into the page.
Ilija Hadzic [Thu, 2 Feb 2012 15:26:24 +0000 (10:26 -0500)]
drm/radeon/kms/blit: fix blit copy for very large buffers
Evergreen and NI blit copy was broken if the buffer maps to a rectangle
whose one dimension is 16384 (max dimension allowed by these chips).
In the mainline kernel, the problem is exposed only when buffers are
very large (1G), but it's still a problem. The problem could be exposed
for smaller buffers if anyone modifies the algorithm for rectangle
construction in r600_blit_create_rect() (the reason why someone would
modify that algorithm is to tune the performance of buffer moves).
The root cause was in i2f() function which only operated on range between
0 and 16383. Fix this by extending the range of i2f() function to 0 to
32767.
While at it improve the function so that the range can be easily
extended in the future (if it becomes necessary), cleanup lines
over 80 characters, and replace in-line comments with one strategic
comment that explains the crux of the function.
Credits to michel@daenzer.net for pointing out the root cause of
the bug.
v2: Fix I2F_MAX_INPUT constant definition goof and warn only once
if input argument is out of range. Edit the comment a little
bit to avoid some linguistic confusion and make it look better
in general.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Michel Dänzer <michel@daenzer.net> Signed-off-by: Dave Airlie <airlied@redhat.com>
Takashi Iwai [Wed, 1 Feb 2012 09:33:23 +0000 (10:33 +0100)]
ALSA: hda - Allow analog low-current mode when dynamic power-control is on
VIA codecs have several different power-saving features, and one of
them is the analog low-current mode. But it turned out that the ALC
mode causes pop-noises at each on/off time on some machines. As a
quick workaround, disable the ALC when another power-saving feature,
the dynamic pin power-control, is turned off, too, since the dynamic
power-control is already exposed as a mixer enum element so that user
can turn it on/off freely.
Takashi Iwai [Tue, 24 Jan 2012 11:25:50 +0000 (12:25 +0100)]
ALSA: hda - Check power-state before changing in patch_via.c
Instead of always writing AC_VERB_SET_POWER_STATE, check the current
power-state and don't write again if the value is already set.
This may reduce the click noise upon the dynamic power-state change
(e.g. in analog-input mixer).
Linus Torvalds [Thu, 2 Feb 2012 02:30:15 +0000 (18:30 -0800)]
Merge tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
firewire fixes post v3.3-rc1
Add workarounds table entries for hardware bugs in
- FireWire part of Sound Blaster Audigy cards,
- Ricoh PCIe 1394 controllers.
Without these, several protocols, e.g. AV/C, do not work on the
Audigy, and the Ricoh PCIe controllers wouldn't work at all.
This does not concern the older Ricoh PCI controllers.
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: disable MSI on Ricoh controllers
firewire: ohci: add reset packet quirk for SB Audigy
Randy Dunlap [Thu, 2 Feb 2012 02:15:49 +0000 (18:15 -0800)]
docbook: fix fatal errors in device-drivers docbook and add DMA Management section
Fix 2 fatal errors in the device-drivers docbook.
Also add some missing files from drivers/base/; since several
of these are DMA-related, add a section for DMA Management.
docproc: drivers/base/sys.c: No such file or directory
docproc: drivers/tty/serial/8250.c: No such file or directory
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 2 Feb 2012 00:00:38 +0000 (16:00 -0800)]
Merge branch 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
lib: Fix 32-bit sparc udiv_qrnnd() definition in mpilib's longlong.h
lib: Fix multiple definitions of clz_tab
lib/digsig: checks for NULL return value
lib/mpi: added missing NULL check
lib/mpi: added comment on divide by 0 case
lib/mpi: check for possible zero length
lib/digsig: pkcs_1_v1_5_decode_emsa cleanup
lib/digsig: additional sanity checks against badly formated key payload
lib/mpi: removed unused functions
lib/mpi: checks for zero divisor length
lib/mpi: return error code on dividing by zero
lib/mpi: replaced MPI_NULL with normal NULL
lib/mpi: added missing NULL check
David Miller [Wed, 1 Feb 2012 22:17:55 +0000 (00:17 +0200)]
lib: Fix 32-bit sparc udiv_qrnnd() definition in mpilib's longlong.h
This copy of longlong.h is extremely dated and results in compile
errors on sparc32 when MPILIB is enabled, copy over the more uptodate
implementation from arch/sparc/math/sfp-util_32.h
Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: James Morris <jmorris@namei.org>
Linus Torvalds [Wed, 1 Feb 2012 23:18:39 +0000 (15:18 -0800)]
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
InfiniBand/RDMA fixes for 3.3:
- Fix a crash due to a regression (uninitialized refcnt) introduced in
3.2 with XRC support.
- Close race in how ucma reports events when connect fails.
- Process vendor-specific MADs in mlx4 so that eg FDR-10 data rate works.
- Fix regression in qib caused by over-aggressive PCIe tuning.
- Other small fixes for hardware drivers (ipath, nes, qib).
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Copyright update
IB/mlx4: pass SMP vendor-specific attribute MADs to firmware
RDMA/nes: Fix fast memory registration opcode
RDMA/nes: Fix fast memory registration length
RDMA/ucma: Discard all events for new connections until accepted
IB/qib: Roll back PCIe tuning change
IB/qib: Use GFP_ATOMIC when locks are held
RDMA/nes: Add missing rcu_read_unlock() in nes_addr_resolve_neigh()
RDMA/nes: Fix for sending MPA reject frame
IB/ipath: Calling PTR_ERR() on right variable in create_file()
RDMA/core: Fix kernel panic by always initializing qp->usecnt
Oleg Nesterov [Tue, 31 Jan 2012 16:15:11 +0000 (17:15 +0100)]
proc: make sure mem_open() doesn't pin the target's memory
Once /proc/pid/mem is opened, the memory can't be released until
mem_release() even if its owner exits.
Change mem_open() to do atomic_inc(mm_count) + mmput(), this only
pins mm_struct. Change mem_rw() to do atomic_inc_not_zero(mm_count)
before access_remote_vm(), this verifies that this mm is still alive.
I am not sure what should mem_rw() return if atomic_inc_not_zero()
fails. With this patch it returns zero to match the "mm == NULL" case,
may be it should return -EINVAL like it did before e268337d.
Perhaps it makes sense to add the additional fatal_signal_pending()
check into the main loop, to ensure we do not hold this memory if
the target task was oom-killed.
This patch fixes merge conflict resolution breakage introduced by merge d3712b9dfcf4 ("Merge tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream").
The commit changed 'mtd_can_have_bb()' function and made it always
return zero, which is incorrect. Instead, we need it to return whether
the underlying flash device can have bad eraseblocks or not. UBI needs
this information because it affects how it handles the underlying flash.
E.g., if the underlying flash is NOR, it cannot have bad blocks and any
write or erase error is fatal, and all we can do is to switch to R/O
mode. We do not need to reserve a pool of good eraseblocks for bad
eraseblocks handling, and so on.
This patch also removes 'mtd_can_have_bb()' invocations from Logfs to
ensure correct Logfs behavior.
I've tested that with this patch UBI works on top of NOR and NAND
flashes emulated by mtdram and nandsim correspondingly.
This patch is based on patch from Linus Torvalds.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Acked-by: Jörn Engel <joern@logfs.org> Acked-by: Prasad Joshi <prasadjoshi.linux@gmail.com> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michel Dänzer [Wed, 1 Feb 2012 11:09:55 +0000 (12:09 +0100)]
drm/radeon: Set DESKTOP_HEIGHT register to the framebuffer (not mode) height.
The value of this register is transferred to the V_COUNTER register at the
beginning of vertical blank. V_COUNTER is the reference for VLINE waits and
goes from VIEWPORT_Y_START to VIEWPORT_Y_START+VIEWPORT_HEIGHT during scanout,
so if VIEWPORT_Y_START is not 0, V_COUNTER actually went backwards at the
beginning of vertical blank, and VLINE waits excluding the whole scanout area
could never finish (possibly only if VIEWPORT_Y_START is larger than the length
of vertical blank in scanlines). Setting DESKTOP_HEIGHT to the framebuffer
height should prevent this for any kind of VLINE wait.
CC: stable@vger.kernel.org Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Seth Forshee [Wed, 1 Feb 2012 01:06:25 +0000 (19:06 -0600)]
drm/radeon/kms: disable output polling when suspended
Polling the outputs when the device is suspended can result in erroneous
status updates. Disable output polling during suspend to prevent this
from happening.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Dmitry Kasatkin [Thu, 26 Jan 2012 17:13:26 +0000 (19:13 +0200)]
lib/digsig: pkcs_1_v1_5_decode_emsa cleanup
Removed useless 'is_valid' variable in pkcs_1_v1_5_decode_emsa(),
which was inhereted from original code. Client now uses return value
to check for an error.
Dmitry Kasatkin [Thu, 26 Jan 2012 17:13:23 +0000 (19:13 +0200)]
lib/mpi: removed unused functions
do_encode_md() and mpi_get_keyid() are not parts of mpi library.
They were used early versions of gnupg and in digsig project,
but they are not used neither here nor there anymore.
Dave Airlie [Wed, 1 Feb 2012 09:36:24 +0000 (09:36 +0000)]
Merge branch 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nv50/pm: signedness bug in nv50_pm_clocks_pre()
drm/nouveau/gem: fix fence_sync race / oops
drm/nouveau: fix typo on mxmdcb option
drm/nouveau/mxm: pretend to succeed, even if we can't shadow the MXM-SIS
drm/nouveau/disp: check that panel power gpio is enabled at init time
Dylan Reid [Tue, 31 Jan 2012 21:04:41 +0000 (13:04 -0800)]
ALSA: hda - Fix calling cs_automic twice for Cirrus codecs.
If cs_automic is called twice (like it is during init) while the mic
is present, it will over-write the last_input with the new one,
causing it to switch back to the automic input when the mic is
unplugged. This leaves the driver in a state (cur_input, last_input,
and automix_idx the same) where the internal mic can not be selected
until it is rebooted without the mic attached.
Check that the mic hasn't already been switched to before setting
last_input.
Dan Carpenter [Wed, 4 Jan 2012 07:20:47 +0000 (10:20 +0300)]
drm/nv50/pm: signedness bug in nv50_pm_clocks_pre()
calc_mclk() returns zero on success and negative on failure but clk is
a u32.
v2: Martin Peres:
- clk should be an int, not a u32
Signed-off-by: Martin Peres <martin.peres@labri.fr> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 10 Jan 2012 00:18:28 +0000 (10:18 +1000)]
drm/nouveau/gem: fix fence_sync race / oops
Due to a race it was possible for a fence to be destroyed while another
thread was trying to synchronise with it. If this happened in the fallback
non-semaphore path, it lead to the following oops due to fence->channel
being NULL.
Ben Skeggs [Wed, 1 Feb 2012 05:08:59 +0000 (15:08 +1000)]
drm/nouveau/mxm: pretend to succeed, even if we can't shadow the MXM-SIS
There's at least one known case where our shadowing code is buggy, and we
fail init. Until we can be confident we're doing all this correctly, lets
succeed and risk crazy bios tables rather than failing for perfectly valid
configs too.
Linus Torvalds [Tue, 31 Jan 2012 17:23:59 +0000 (09:23 -0800)]
Merge tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream
There are few important bug fixes for LogFS
* tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream:
Logfs: Allow NULL block_isbad() methods
logfs: Grow inode in delete path
logfs: Free areas before calling generic_shutdown_super()
logfs: remove useless BUG_ON
MAINTAINERS: Add Prasad Joshi in LogFS maintiners
logfs: Propagate page parameter to __logfs_write_inode
logfs: set superblock shutdown flag after generic sb shutdown
logfs: take write mutex lock during fsync and sync
logfs: Prevent memory corruption
logfs: update page reference count for pined pages
Fix up conflict in fs/logfs/dev_mtd.c due to semantic change in what
"mtd->block_isbad" means in commit f2933e86ad93: "Logfs: Allow NULL
block_isbad() methods" clashing with the abstraction changes in the
commits 7086c19d0742: "mtd: introduce mtd_block_isbad interface" and d58b27ed58a3: "logfs: do not use 'mtd->block_isbad' directly".
This resolution takes the semantics from commit f2933e86ad93, and just
makes mtd_block_isbad() return zero (false) if the 'block_isbad'
function is NULL. But that also means that now "mtd_can_have_bb()"
always returns 0.
Now, "mtd_block_markbad()" will obviously return an error if the
low-level driver doesn't support bad blocks, so this is somewhat
non-symmetric, but it actually makes sense if a NULL "block_isbad"
function is considered to mean "I assume that all my blocks are always
good".
The user reports that model=auto works better than current handling
on a 3.2 based kernel (with jack detection patches backported).
Since model=auto is what we prefer these days anyway, the quirk
should be removed.
Alsa-info for the relevant machine:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/923316/+attachment/2702812/+files/alsa-info.txt.Pbfno2x7bp
BugLink: https://bugs.launchpad.net/bugs/923316 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA: HDA: Fix jack creation for codecs with front and rear Line In
If a codec has both a front and a rear Line In, two controls both
named "Line Jack" will be created, which causes parsing to fail.
While a long term solution might be to name the jacks differently,
this extra check is consistent with what is already being done in many
auto-parsers, and will also protect against other cases when two
inputs have the same label.
BugLink: https://bugs.launchpad.net/bugs/923409 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
selects GENERIC_CPU_DEVICES for Microblaze which register cpu.
My patch was done in the same time that's why cpu was registered twice which
caused this warning log:
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:481 sysfs_add_one+0xb0/0xdc()
sysfs: cannot create duplicate filename '/devices/system/cpu/cpu0'
Modules linked in:
...
Linus Torvalds [Tue, 31 Jan 2012 01:08:40 +0000 (17:08 -0800)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (w83627ehf) Disable setting DC mode for pwm2, pwm3 on NCT6776F
hwmon: (sht15) fix bad error code
MAINTAINERS: Drop maintainer for MAX1668 hwmon driver
MAINTAINERS: Add hwmon entries for Wolfson
hwmon: (f71805f) Fix clamping of temperature limits
Linus Torvalds [Tue, 31 Jan 2012 01:06:26 +0000 (17:06 -0800)]
Merge branch 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Here are some fixes to the pin control system that has accumulated since
-rc1. Mainly Tony Lindgren fixed the module load/unload logic and the
rest are minor fixes and documentation.
* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: add checks for empty function names
pinctrl: fix pinmux_hog_maps when ctrl_dev_name is not set
pinctrl: fix some pinmux typos
pinctrl: free debugfs entries when unloading a pinmux driver
pinctrl: unbreak error messages
Documentation/pinctrl: fix a few syntax errors in code examples
pinctrl: fix pinconf_pins_show iteration
Stephane Eranian [Mon, 30 Jan 2012 10:50:37 +0000 (11:50 +0100)]
perf top: Fix number of samples displayed
In recent versions of perf top, pressing the 'e' key to change the
number of displayed samples had no effect.
The number of samples was still dictated by the size of the terminal
(stdio mode). That was quite annoying because typically only the first
dozen samples really matter.
This patch fixes this.
Cc: David Ahern <dsahern@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20120130105037.GA5160@quad Signed-off-by: Stephane Eranian <eranian@google.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stephane Eranian [Fri, 20 Jan 2012 09:49:12 +0000 (10:49 +0100)]
perf tools: Fix strlen() bug in perf_event__synthesize_event_type()
The event_type record has a max length for the event name.
It's called MAX_EVENT_NAME.
The name may be truncated to fit the max length. But the header.size still
reflects the original name length. If that length is > MAX_EVENT_NAME, then the
header.size field is bogus. Fix this by using the length of the name after the
potential truncation.
Cc: David Ahern <dsahern@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20120120094912.GA4882@quad Signed-off-by: Stephane Eranian <eranian@google.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
David Daney [Tue, 17 Jan 2012 21:41:01 +0000 (13:41 -0800)]
perf tools: Fix broken build by defining _GNU_SOURCE in Makefile
When building on my Debian/mips system, util/util.c fails to build
because commit 1aed2671738785e8f5aea663a6fda91aa7ef59b5 (perf kvm: Do
guest-only counting by default) indirectly includes stdio.h before the
feature selection in util.h is done. This prevents _GNU_SOURCE in
util.h from enabling the declaration of getline(), from now second
inclusion of stdio.h, and the build is broken.
There is another breakage in util/evsel.c caused by include ordering,
but I didn't fully track down the commit that caused it.
The root cause of all this is an inconsistent definition of _GNU_SOURCE,
so I move the definition into the Makefile so that it is passed to all
invocations of the compiler and used uniformly for all system header
files. All other #define and #undef of _GNU_SOURCE are removed as they
cause conflicts with the definition passed to the compiler.
All the features.h definitions (_LARGEFILE64_SOURCE _FILE_OFFSET_BITS=64
and _GNU_SOURCE) are needed by the python glue code too, so they are
moved to BASIC_CFLAGS, and the misleading comments about BASIC_CFLAGS
are removed.
This gives me a clean build on x86_64 (fc12) and mips (Debian).
Cc: David Daney <david.daney@cavium.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Joerg Roedel <joerg.roedel@amd.com> Cc: Namhyung Kim <namhyung.kim@lge.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1326836461-11952-1-git-send-email-ddaney.cavm@gmail.com Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jack Morgenstein [Thu, 26 Jan 2012 14:41:33 +0000 (16:41 +0200)]
IB/mlx4: pass SMP vendor-specific attribute MADs to firmware
In the current code, vendor-specific MADs (e.g with the FDR-10
attribute) are silently dropped by the driver, resulting in timeouts
at the sending side and inability to query/configure the relevant
feature. However, the ConnectX firmware is able to handle such MADs.
For unsupported attributes, the firmware returns a GET_RESPONSE MAD
containing an error status.
For example, for a FDR-10 node with LID 11:
# ibstat mlx4_0 1
CA: 'mlx4_0'
Port 1:
State: Active
Physical state: LinkUp
Rate: 40 (FDR10)
Base lid: 11
LMC: 0
SM lid: 24
Capability mask: 0x02514868
Port GUID: 0x0002c903002e65d1
Link layer: InfiniBand
Extended Port Query (EPI) vendor mad timeouts before the patch:
# smpquery MEPI 11 -d
ibwarn: [4196] smp_query_via: attr 0xff90 mod 0x0 route Lid 11
ibwarn: [4196] _do_madrpc: retry 1 (timeout 1000 ms)
ibwarn: [4196] _do_madrpc: retry 2 (timeout 1000 ms)
ibwarn: [4196] _do_madrpc: timeout after 3 retries, 3000 ms
ibwarn: [4196] mad_rpc: _do_madrpc failed; dport (Lid 11)
smpquery: iberror: [pid 4196] main: failed: operation EPI: ext port info query failed
EPI query works OK with the patch:
# smpquery MEPI 11 -d
ibwarn: [6548] smp_query_via: attr 0xff90 mod 0x0 route Lid 11
ibwarn: [6548] mad_rpc: data offs 64 sz 64
mad data
0000 0000 0000 0001 0000 0001 0000 0001
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
# Ext Port info: Lid 11 port 0
StateChangeEnable:...............0x00
LinkSpeedSupported:..............0x01
LinkSpeedEnabled:................0x01
LinkSpeedActive:.................0x01
Signed-off-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Acked-by: Ira Weiny <weiny2@llnl.gov> Cc: <stable@vger.kernel.org> Signed-off-by: Roland Dreier <roland@purestorage.com>
Linus Torvalds [Mon, 30 Jan 2012 23:17:21 +0000 (15:17 -0800)]
Merge tag 'tty-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Here are some tty/serial patches for 3.3-rc1
Big thing here is the movement of the 8250 serial drivers to their own
directory, now that the patch churn has calmed down.
Other than that, only minor stuff (omap patches were reverted as they
were found to be wrong), and another broken driver removed from the
system.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* tag 'tty-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: Kill off Moorestown code
Revert "tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode"
Revert "tty: serial: OMAP: transmit FIFO threshold interrupts don't wake the chip"
serial: Fix wakeup init logic to speed up startup
docbook: don't use serial_core.h in device-drivers book
serial: amba-pl011: lock console writes against interrupts
amba-pl011: do not disable RTS during shutdown
tty: serial: OMAP: transmit FIFO threshold interrupts don't wake the chip
tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode
omap-serial: make serial_omap_restore_context depend on CONFIG_PM_RUNTIME
omap-serial :Make the suspend/resume functions depend on CONFIG_PM_SLEEP.
TTY: fix UV serial console regression
jsm: Fixed EEH recovery error
Updated TTY MAINTAINERS info
serial: group all the 8250 related code together
is unable to access attached FireWire devices when MSI is enabled but
works if MSI is disabled.
http://www.mail-archive.com/alsa-user@lists.sourceforge.net/msg28251.html
Hence add the "disable MSI" quirks flag for this device, or in fact for
safety and simplicity for all current (R5U230, R5U231, R5U240) and
future Ricoh PCIe 1394 controllers.
Reported-by: Stefan Thomas <kontrapunktstefan@googlemail.com> Cc: 2.6.36+ <stable@vger.kernel.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Linus Torvalds [Mon, 30 Jan 2012 19:38:28 +0000 (11:38 -0800)]
Merge tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Here are a bunch of USB patches for 3.3-rc1.
Nothing major, largest thing here is the removal of some drivers that
did not work at all. Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (52 commits)
uwb & wusb: fix kconfig error
USB: Realtek cr: fix autopm scheduling while atomic
USB: ftdi_sio: Add more identifiers
xHCI: Cleanup isoc transfer ring when TD length mismatch found
usb: musb: omap2430: minor cleanups.
qcaux: add more Pantech UML190 and UML290 ports
Revert "drivers: usb: Fix dependency for USB_HWA_HCD"
usb: mv-otg - Fix build if CONFIG_USB is not set
USB: cdc-wdm: Avoid hanging on interface with no USB_CDC_DMM_TYPE
usb: add support for STA2X11 host driver
drivers: usb: Fix dependency for USB_HWA_HCD
kernel-doc: fix new warning in usb.h
USB: OHCI: fix new compiler warnings
usb: serial: kobil_sct: fix compile warning:
drivers/usb/host/ehci-fsl.c: add missing iounmap
USB: cdc-wdm: better allocate a buffer that is at least as big as we tell the USB core
USB: cdc-wdm: call wake_up_all to allow driver to shutdown on device removal
USB: cdc-wdm: use two mutexes to allow simultaneous read and write
USB: cdc-wdm: updating desc->length must be protected by spin_lock
USB: usbsevseg: fix max length
...
1) Setting link attributes can modify the size of the attributes that
would be reported on a subsequent getlink netlink operation,
therefore min_ifinfo_dump_size needs to be adjusted. From Stefan
Gula.
2) Resegmentation of TSO frames while trimming can violate invariants
expected by callers, namely that the number of segments can only stay
the same or decrease, never increase. If MSS changes, however, we
can trim data but then end up with more segments. Fix this by only
segmenting to the MSS already recorded in the SKB. That's the
simplest fix for now and if we want to get more fancy in the future
that's a more involved change.
This probably explains some retransmit counter inaccuracies.
From Neal Cardwell.
3) Fix too-many-wakeups in POLL with AF_UNIX sockets, from Eric Dumazet.
4) Fix CAIF crashes wrt. namespace handling. From Eric Dumazet and
Eric W. Biederman.
5) TCP port selection fixes from Flavio Leitner.
6) More socket memory cgroup build fixes in certain randonfig
situations. From Glauber Costa.
7) Fix TCP memory sysctl regression reported by Ingo Molnar, also from
Glauber Costa.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
af_unix: fix EPOLLET regression for stream sockets
tcp: fix tcp_trim_head() to adjust segment count with skb MSS
net/tcp: Fix tcp memory limits initialization when !CONFIG_SYSCTL
net caif: Register properly as a pernet subsystem.
netns: Fail conspicously if someone uses net_generic at an inappropriate time.
net: explicitly add jump_label.h header to sock.h
net: RTNETLINK adjusting values of min_ifinfo_dump_size
ipv6: Fix ip_gre lockless xmits.
xen-netfront: correct MAX_TX_TARGET calculation.
netns: fix net_alloc_generic()
tcp: bind() optimize port allocation
tcp: bind() fix autoselection to share ports
l2tp: l2tp_ip - fix possible oops on packet receive
iwlwifi: fix PCI-E transport "inta" race
mac80211: set bss_conf.idle when vif is connected
mac80211: update oper_channel on ibss join
Linus Torvalds [Mon, 30 Jan 2012 18:16:25 +0000 (10:16 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
This fixes an integration issue with the regulator device tree bindings
which shook out in -rc. The bindings were overly enthusiatic when
deciding to set a voltage on a regulator and would try to set zero volts
on an unconfigured regulator which isn't supported.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Set apply_uV only when min and max voltages are defined