Tim Gardner [Thu, 7 Feb 2013 19:35:35 +0000 (12:35 -0700)]
brcmsmac: fix u16 overflow warning
DOT11_MIN_BEACON_PERIOD and DOT11_MAX_BEACON_PERIOD are
superfluous. The only invalid beacon period is 0. Comparing
a 16 bit quantity to 0xffff also causes a compile warning:
It can, if invalid argument given, return a negative value. In that
case we would access arrays out-of-bounds and such. Check the value
and yell loudly if that happened as it would be a bug in the
implementation. (Instead of silently corrupting memory.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Nick Kossifidis <mickflemm@gmail.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 6 Feb 2013 18:54:17 +0000 (12:54 -0600)]
rtlwifi: rtl8192cu: Fix NULL dereference BUG when using new_id
When the new_id entry in /sysfs is used for a foreign USB device, rtlwifi
BUGS with a NULL pointer dereference because the per-driver configuration
data is not available. The probe function has been restructured as
suggested by Ben Hutchings <bhutchings@solarflare.com>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: fix problem connecting to AP without security
The bcm43236 device showed having an issue connection to an AP without
security when auth_type was set to automatic. For this particular device
a workaround is made by selecting open-system. This problem does not
occur when using wpa_supplicant as it will not use auth type automatic.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: add function to retrieve chip information
Added function to obtain chip information for chip specific
code.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac: add chip information to the bus interface
Extend the bus interface with chip identifier and revision. This
will be used when certain devices need special handling in the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Wed, 6 Feb 2013 17:40:44 +0000 (18:40 +0100)]
brcmfmac: Use single function for channel to chanspec.
Simplify code by using single function for converting channel to
chanspec. No need to set 40MHz flags, as they are not needed for
correct working in FW.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Wed, 6 Feb 2013 17:40:43 +0000 (18:40 +0100)]
brcmfmac: Cleanup function brcmf_notifiy_connect_status_ap.
Clean up function, removing some unnecessary code and
initialisation.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Wed, 6 Feb 2013 17:40:42 +0000 (18:40 +0100)]
brcmfmac: Update tracelogging for multiple netdevs.
When supporting multiple netdevs it is usefull to log idx in netdev
related functions. This will be used for features like P2P.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Wed, 6 Feb 2013 17:40:40 +0000 (18:40 +0100)]
brcmfmac: Add logging for FIL int set/get cmds.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Wed, 6 Feb 2013 17:40:38 +0000 (18:40 +0100)]
brcmfmac: Use struct brcmf_if in brcmf_configure_opensecurity.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Wed, 6 Feb 2013 17:40:37 +0000 (18:40 +0100)]
brcmfmac: Remove copy mac address from drvr at netdev up.
At netdev up the mac address from drvr is copied to netdev mac
address. This is incorrect and mac address was already set by
brcmf_net_attach by copying it from ifp.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54usb: corrected USB ID for T-Com Sinus 154 data II
Corrected USB ID for T-Com Sinus 154 data II. ISL3887-based. The
device was tested in managed mode with no security, WEP 128
bit and WPA-PSK (TKIP) with firmware 2.13.1.0.lm87.arm (md5sum: 7d676323ac60d6e1a3b6d61e8c528248). It works.
Signed-off-by: Tomasz Guszkowski <tsg@o2.pl> Cc: <stable@vger.kernel.org> Acked-By: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Info coming from Sweex Windows driver and wikidevi.com
0x177f,0x0163 Sweex LW163 RT3370 1x1, int. antenna
0x177f,0x0164 Sweex LW164 RT8070 1x1, Nano dongle
0x177f,0x0165 Sweex LW165 RT3370 1x1, ext. antenna
0x177f,0x0324 Sweex LW324 RT3072 2x2 with 32Mb NOR flash, autoinstall
Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: users@rt2x00.serialmonkey.com Cc: linux-wireless@vger.kernel.org Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Thu, 31 Jan 2013 08:16:46 +0000 (11:16 +0300)]
NFC: llcp: integer underflow in nfc_llcp_set_remote_gb()
If gb_len is less than 3 it would cause an integer underflow and
possibly memory corruption in nfc_llcp_parse_gb_tlv().
I removed the old test for gb_len == 0. I also removed the test for
->remote_gb == NULL. It's not possible for ->remote_gb to be NULL and
we have already dereferenced ->remote_gb_len so it's too late to test.
The old test return -ENODEV but my test returns -EINVAL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge tag 'nfc-next-3.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel says:
"This is the 2nd NFC pull request.
With this one we have a new NFC driver for Inside Secure microread and a few
pn533 fixes.
Microread is an HCI based NFC IP and the driver we're pushing supports tags
R/W, and NFC p2p. It's supported over the i2c and MEI busses."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Fixed-up drivers/net/wireless/iwlwifi/mvm/mac80211.c to change change
IEEE80211_HW_NEED_DTIM_PERIOD to IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC
as requested by Johannes Berg. -- JWL
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luciano Coelho [Thu, 7 Feb 2013 09:35:33 +0000 (11:35 +0200)]
wlcore: fix wrong remote rates when starting STA role
In wl18xx, we use a new ACX command in order to set the remote
supported rates, once we know it (ie. after association). The wl12xx
firmware doesn't support changing the rates after the STA is started,
so we need to use all supported rates.
Commit 530abe19 (wlcore: add ACX_PEER_CAP command) broke that by using
wlvif->rate_set when starting the STA role.
wl18xx: add new phy configuration parameters for telec support
Add back-off settings to the wl18xx_mac_and_phy_params. We had an
empty space where the new parameters are added, so this change doesn't
affect backwards-compatibility with older firmwares.
Update WL18XX_CONF_VERSION accordingly.
Signed-off-by: Victor Goldenshtein <victorg@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Wed, 30 Jan 2013 08:53:14 +0000 (10:53 +0200)]
wlcore: don't hide real error code when booting fails
There's no need to hide the actual error that was reported when
booting fails. For instance, on I/O error, we were returing
-EINVALID, which doesn't make sense at all.
Luciano Coelho [Fri, 25 Jan 2013 10:05:34 +0000 (12:05 +0200)]
wlcore: move wl12xx_platform_data up and make it truly optional
The platform data is used not only by wlcore-based drivers, but also
by wl1251. Move it up in the directory hierarchy to reflect this.
Additionally, make it truly optional. At the moment, disabling
platform data while wl1251_sdio or wlcore_sdio are enabled doesn't
work, but it will be necessary when device tree support is
implemented.
Signed-off-by: Luciano Coelho <coelho@ti.com> Reviewed-by: Felipe Balbi <balbi@ti.com>
Luciano Coelho [Wed, 23 Jan 2013 14:40:37 +0000 (16:40 +0200)]
wlcore: use PLATFORM_DEVID_AUTO for plat dev creation to avoid conflicts
The platform devices can be created by both wlcore_sdio and
wlcore_spi. Theoretically, if both are connected to the same board,
there will be a conflict.
Reported-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Fri, 25 Jan 2013 09:57:48 +0000 (11:57 +0200)]
wlcore: remove if_ops from platform_data
We can't pass pointers from the platform data to the modules, because
with DT it cannot be done. Those pointers are not set by the board
files anyway. It's the bus modules that set them, so they can be
safely removed from the platform data without changing any board
files.
Create a new structure that the bus modules pass to wlcore. This
structure contains the if_ops pointers and a pointer to the actual
platform data.
Signed-off-by: Luciano Coelho <coelho@ti.com> Reviewed-by: Felipe Balbi <balbi@ti.com>
Luciano Coelho [Wed, 12 Dec 2012 08:14:22 +0000 (10:14 +0200)]
wlcore: use single-role version when verifying the PLT firmware
The PLT firmware used by wl12xx for calibration always has the same
version number as the single-role firmware.
Currntly the driver rejects the PLT firmware since anything that is
not single-role uses the multi-role version. Fix this by using the
single-role version for everything except multi-role.
Marco Porsch [Wed, 30 Jan 2013 17:14:08 +0000 (18:14 +0100)]
mac80211: mesh power save basics
Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods
Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.
Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.
Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.
Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).
Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.
Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.
Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 29 Jan 2013 10:35:29 +0000 (11:35 +0100)]
mac80211: send deauth if connection was lost during suspend
If the driver determined the connection was lost or that
it couldn't securely maintain the connection when coming
out of WoWLAN, send a deauth frame to the AP to also let
it know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 29 Jan 2013 10:41:38 +0000 (11:41 +0100)]
mac80211: allow transmitting deauth with tainted key
When we had a connection for WoWLAN and after resume it
needed to be disconnected, the previous commit enabled
sending a deauth frame to the AP. This frame would not
go through on MFP-enabled networks as the key for it is
marked tainted before the frame is transmitted.
Allow a tainted key to be used for deauth frames. Worst
case, we'll use a wrong key because the PTK was rekeyed
while suspended, but more likely the PTK is still fine
and the taint flag really only applies to the GTK(s).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 29 Jan 2013 23:40:20 +0000 (00:40 +0100)]
cfg80211: simplify mesh BSS comparison
Instead of first checking if a BSS is an MBSS
and then doing the comparisons, inline it all
into the BSS comparison function. This avoids
doing the IE searches twice and is also a lot
less code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 1 Feb 2013 18:20:03 +0000 (19:20 +0100)]
cfg80211: fix BSS list hidden SSID lookup
When trying to find a hidden SSID, the lookup function
is done wrong; the code is trying to combine the two
lookups into one, and as a consequence doesn't always
find the entry at all. To understand this, consider a
case where multiple BSS entries with the same channel
and BSSID exist but have different SSID length. Then
comparing against the probe response SSID length is
bound to cause problems since the hidden one might be
either zeroed out or zero-length.
To fix this we need to do two lookups for the two ways
to hide SSIDs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211: expand per-station byte counters to 64bit
In per-station statistics, present 32bit counters are too small
for practical purposes - with gigabit speeds, it get overlapped
every few seconds.
Expand counters in the struct station_info to be 64-bit.
Driver can still fill only 32-bit and indicate in @filled
only bits like STATION_INFO_[TR]X_BYTES; in case driver provides
full 64-bit counter, it should also set in @filled
bit STATION_INFO_[TR]RX_BYTES64
Netlink sends both 32-bit and 64-bit counters, if present, to not
break userspace.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[change to also have 32-bit counters if driver advertises 64-bit] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With multi-channel, there's a corner case where a driver
doesn't receive a beacon soon enough to be able to sync
its timers with the AP. In this case, the only recovery
(after trying again) is to disconnect from the AP. Allow
calling ieee80211_connection_loss() for such cases. To
make that possible, modify the work function to not rely
on the IEEE80211_HW_CONNECTION_MONITOR flag but use new
state kept in the interface instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 29 Jan 2013 12:09:34 +0000 (13:09 +0100)]
mac80211: send deauth when connection is lost
If the driver determines the connection is lost,
send a deauth frame to the AP anyway just in case
it still considers the connection alive. The frame
might not go through, but at least we've tried.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Larry Finger [Fri, 1 Feb 2013 16:40:27 +0000 (10:40 -0600)]
rtlwifi: rtl8723ae: Fix W=1 compile warnings
Whe this driver is built with "make W=1", the following warnings are output:
drivers/net/wireless/rtlwifi/rtl8723ae/fw.c:515:5: warning: variable ‘own’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/hal_btc.c:1436:5: warning: variable ‘bt_retry_cnt’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/hw.c:706:6: warning: variable ‘reg_ratr’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/hw.c:2033:41: warning: variable ‘cur_rfstate’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:620:23: warning: variable ‘radiob_arraylen’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:619:7: warning: variable ‘radiob_array_table’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:617:7: warning: variable ‘rtstatus’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1534:6: warning: variable ‘bbvalue’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1716:6: warning: variable ‘reg_ecc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1715:61: warning: variable ‘reg_ec4’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/phy.c:1715:34: warning: variable ‘reg_eac’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:247:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 1 Feb 2013 16:40:23 +0000 (10:40 -0600)]
rtlwifi: Fix warnings in usb.c
Building this driver with "make W=1" results in the following 2 warnings:
drivers/net/wireless/rtlwifi/usb.c:829:21: warning: variable ‘urb_list’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/usb.c:828:23: warning: variable ‘skb_list’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: users@rt2x00.serialmonkey.com Cc: linux-wireless@vger.kernel.org Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sven Eckelmann [Thu, 31 Jan 2013 09:26:44 +0000 (10:26 +0100)]
ath9k: Select RELAY for ATH9K_DEBUGFS
The spectral scan support activated through ATH9K_DEBUGFS depends on RELAY for
the kernel->userspace communication. Not activating RELAY causes build
failures.
The RELAY is added as select instead of depend to do it similar like
the only other user of RELAY: BLK_DEV_IO_TRACE
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Thu, 31 Jan 2013 03:56:01 +0000 (19:56 -0800)]
mwifiex: do not reconfigure tx buffer size in firmware while associating
It's observed that reconfiguration of tx buffer size before
association can cause data path failure in firmware after
associated. Although this is only found with PCIe cards, but
potentially it could happen with any other interfaces as well.
The tx buffer reconfiguration is not really useful in firmware.
Let's remove it for all interfaces.
Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k hardware reports whenever an frame was part
of an A-MPDU. MAC80211 already provides the necessary
API to pass this additional information along to
whomever needs it.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices were taken from Ralink Linux drivers:
- RT5370
0x043e, 0x7a32
0x043e, 0x7a42
0x0471, 0x2126
0x0471, 0x2180
0x0471, 0x2181
0x0471, 0x2182
Identify these ones:
0x04da, 0x23f6 in CONFIG_RT2800USB_RT53XX is a Panasonic device
0x07d1, 0x3c17 in RT2800USB_UNKNOWN is a RT3070
0x0586, 0x341a in RT2800USB_UNKNOWN is a RT3070
Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: users@rt2x00.serialmonkey.com Cc: linux-wireless@vger.kernel.org Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on "iwlwifi: report A-MPDU status".
(12bf6f45d1703858)
Since the firmware will give us an A-MPDU bit and
only a single PHY information packet for all the
subframes in an A-MPDU, we can easily report the
minimal A-MPDU information for radiotap.
Cc: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andre Guedes [Fri, 1 Feb 2013 14:21:30 +0000 (11:21 -0300)]
Bluetooth: Refactor mgmt_pending_foreach
This patch does a trivial refactor in mgmt_pending_foreach function.
It replaces list_for_each_safe by list_for_each_entry_safe, simplifying
the function.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Andre Guedes [Tue, 29 Jan 2013 22:59:56 +0000 (19:59 -0300)]
Bluetooth: Reduce critical section in sco_conn_ready
This patch reduces the critical section protected by sco_conn_lock in
sco_conn_ready function. The lock is acquired only when it is really
needed.
This patch fixes the following lockdep warning which is generated
when the host terminates a SCO connection.
Today, this warning is a false positive. There is no way those
two threads reported by lockdep are running at the same time since
hdev->workqueue (where rx_work is queued) is single-thread. However,
if somehow this behavior is changed in future, we will have a
potential deadlock.
======================================================
[ INFO: possible circular locking dependency detected ]
3.8.0-rc1+ #7 Not tainted
-------------------------------------------------------
kworker/u:1H/1018 is trying to acquire lock:
(&(&conn->lock)->rlock){+.+...}, at: [<ffffffffa0033ba6>] sco_chan_del+0x66/0x190 [bluetooth]
but task is already holding lock:
(slock-AF_BLUETOOTH-BTPROTO_SCO){+.+...}, at: [<ffffffffa0033d5a>] sco_conn_del+0x8a/0xe0 [bluetooth]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Johan Hedberg [Sun, 27 Jan 2013 14:32:00 +0000 (08:32 -0600)]
Bluetooth: Fix link security setting when powering on
If a controller is powered on while the HCI_AUTO_OFF flag is set the
link security setting (HCI_LINK_SECURITY) might not be in sync with the
actual state of the controller (HCI_AUTH). This patch fixes the issue by
checking for inequality between the intended and actual settings and
sends a HCI_Write_Auth_Enable command if necessary.
Johan Hedberg [Sat, 26 Jan 2013 22:31:33 +0000 (00:31 +0200)]
Bluetooth: Refactor UUID-16 list generation into its own function
We will need to create three separate UUID lists in the EIR data (for
16, 32 and 128 bit UUIDs) so the code is easier to follow if each list
is generated in their own function.
Johan Hedberg [Sat, 26 Jan 2013 22:31:32 +0000 (00:31 +0200)]
Bluetooth: Remove useless eir_len variable from EIR creation
The amount of data encoded so far in the create_eir() function can be
calculated simply through the difference between the data and ptr
pointer variables. The eir_len variable then becomes essentially
useless.
Johan Hedberg [Sat, 26 Jan 2013 22:31:31 +0000 (00:31 +0200)]
Bluetooth: Simplify UUID16 list generation for EIR
There's no need to use two separate loops to generate a UUID list for
the EIR data. This patch merges the two loops previously used for the
16-bit UUID list generation into a single loop, thus simplifying the
code a great deal.
Johan Hedberg [Sat, 26 Jan 2013 22:31:29 +0000 (00:31 +0200)]
Bluetooth: Keep track of UUID type upon addition
The primary purpose of the UUIDs is to enable generation of EIR and AD
data. In these data formats the UUIDs are split into separate fields
based on whether they're 16, 32 or 128 bit UUIDs. To make the generation
of these data fields simpler this patch adds a type member to the
bt_uuid struct and assigns a value to it as soon as the UUID is added to
the kernel. This way the type doesn't need to be calculated each time
the UUID list is later iterated.
Johan Hedberg [Sat, 26 Jan 2013 22:31:27 +0000 (00:31 +0200)]
Bluetooth: Store UUIDs in the same order that they were added
We should be encoding UUIDs to the EIR data in the same order that they
were added to the kernel, i.e. each UUID should be added to the end of
the UUIDs list. This patch fixes the issue by using list_add_tail
instead of list_add for storing the UUIDs.
Lilach Edelstein [Wed, 16 Jan 2013 09:34:49 +0000 (11:34 +0200)]
iwlwifi: move register access lock into transport
Move the reg_lock that protects HW register access
into the transport implementation. Locking is no
longer exposed, but handled internally in grab and
release NIC access. This simplifies the users.
Lilach Edelstein [Sun, 13 Jan 2013 11:31:10 +0000 (13:31 +0200)]
iwlwifi: add iwl_set_bits_mask to transport API
Express iwl_set_bit() and iwl_clear_bit() through iwl_set_bits_mask()
and add the latter to the transport's API in order to allow different
implementation for different transport types in the future.
As the rate scaling algorithm will attempt to enable
aggregation over and over again, the message will
flood the log if there is, for example, Bluetooth
streaming music. Make it a debug messages instead of
printing it all the time.
mac80211: improve latency and throughput while software scanning
Patch vastly improve latency while scanning. Slight throughput
improvements were observed as well. Is intended for improve performance
of voice and video applications, when scan is periodically requested by
user space (i.e. default NetworkManager behaviour).
Patch remove latency requirement based on PM_QOS_NETWORK_LATENCY,
this value is 2000 seconds by default (i.e. approximately 0.5 hour !?!).
Also remove listen interval requirement, which based on beaconing and
depending on BSS parameters. It can make we stay off-channel for a
second or more.
Instead try to offer the best latency that we could, i.e. be off-channel
no longer than PASSIVE channel scan time: 125 ms. That mean we will
scan two ACTIVE channels and go back to on-channel, and one PASSIVE
channel, and go back to on-channel.
Patch also decrease PASSIVE channel scan time to about 110 ms.
As drawback patch increase overall scan time. On my tests, when scanning
both 2GHz and 5GHz bands, scanning time increase from 5 seconds up to 10
seconds. Since that increase happen only when we are associated, I think
it can be acceptable. If eventually better scan time is needed for
situations when we lose signal and quickly need to decide to which AP
roam, additional scan flag or parameter can be introduced.
I tested patch by doing:
while true; do iw dev wlan0 scan; sleep 3; done > /dev/null
and
ping -i0.2 -c 1000 HOST
on remote and local machine, results are as below:
* Ping from local periodically scanning machine to AP:
Unpatched: rtt min/avg/max/mdev = 0.928/24.946/182.135/36.873 ms
Patched: rtt min/avg/max/mdev = 0.928/19.678/150.845/33.130 ms
* Ping from remote machine to periodically scanning machine:
Unpatched: rtt min/avg/max/mdev = 1.637/120.683/709.139/164.337 ms
Patched: rtt min/avg/max/mdev = 1.807/26.893/201.435/40.284 ms
Throughput measured by scp show following results.
Johannes Berg [Tue, 29 Jan 2013 14:02:27 +0000 (15:02 +0100)]
mac80211: start auth/assoc timeout on frame status
When sending authentication/association frames they
might take a bit of time to go out because we may
have to synchronise with the AP, in particular in
the case where it's really a P2P GO. In this case
the 200ms fixed timeout could potentially be too
short if the beacon interval is relatively large.
For drivers that report TX status we can do better.
Instead of starting the timeout directly, start it
only when the frame status arrives. Since then the
frame was out on the air, we can wait shorter (the
typical response time is supposed to be 30ms, wait
100ms.) Also, if the frame failed to be transmitted
try again right away instead of waiting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 29 Jan 2013 21:37:48 +0000 (22:37 +0100)]
cfg80211: remove free_priv BSS API
Now that mac80211 no longer uses this API, remove
it completely. If anyone needs it again, we can
revert this patch of course, but mac80211 was the
only user right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: inform the driver about update of dtim_period
Currently, when the driver requires the DTIM period,
mac80211 will wait to hear a beacon before association.
This behavior is suboptimal since some drivers may be
able to deal with knowing the DTIM period after the
association, if they get it at all.
To address this, notify the drivers with bss_info_changed
with the new BSS_CHANGED_DTIM_PERIOD flag when the DTIM
becomes known. This might be when changing to associated,
or later when the entire association was done with only
probe response information.
Rename the hardware flag for the current behaviour to
IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC to more accurately
reflect its behaviour. IEEE80211_HW_NEED_DTIM_PERIOD is
no longer accurate as all drivers get the DTIM period
now, just not before association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 22 Jan 2013 11:34:29 +0000 (12:34 +0100)]
cfg80211/mac80211: support reporting wakeup reason
When waking up from WoWLAN, it is useful to know
what triggered the wakeup. Support reporting the
wakeup reason(s) in cfg80211 (and a pass-through
in mac80211) to allow userspace to know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>