Current ak4642 was not able to select pll.
This patch add support it.
It still expect PLL base input pin is MCKI.
see Table 5 "setting of PLL Mode" of datasheet
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 22 Mar 2010 16:37:01 +0000 (16:37 +0000)]
ASoC: Allow WM8903 mic detect disable and don't force bias on
Don't force enable the microphone bias on WM8903 when doing jack
detection, and don't force enable microphone bias. This allows
platforms to only enable microphone detection when a jack has been
inserted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Mon, 22 Mar 2010 15:30:30 +0000 (15:30 +0000)]
ASoC: Allow disabling of WM835x jack detection
If no report is specified then disable detection. Note that we don't
disable the slow clock, though the power consumption from it should
be negligable. That should be reference counted, ideally through DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Mon, 22 Mar 2010 13:36:13 +0000 (13:36 +0000)]
ASoC: Allow force enabled pins to be disabled
Some systems, such as those with mechanical jack detection, may wish
to force enable a pin (typically mic bias) only some of the time.
Support such systems by having disable_pin() also coveer force enabled
pins.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown [Mon, 22 Mar 2010 12:06:30 +0000 (12:06 +0000)]
ASoC: Add a notifier for jack status changes
Some systems provide both mechanical and electrical detection of jack
status changes. On such systems power savings can be achieved by only
enabling the electrical detection methods when physical insertion has
been detected.
Begin supporting such systems by providing a notifier for jack status
changes which can be used to trigger any reconfiguration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Peter Ujfalusi [Mon, 22 Mar 2010 15:46:37 +0000 (17:46 +0200)]
ASoC: TWL4030: PM fix for output amplifiers
Gain controls on outputs affect the power consumption
when the gain is set to non 0 value.
Outputs with amps have one register to configure the
routing and the gain:
PREDL_CTL (0x25):
bit 0: Voice enable
bit 1: Audio L1 enable
bit 2: Audio L2 enable
bit 3: Audio R2 enable
bit 4-5: Gain (0x0 - power down, 0x1 - 6dB, 0x2 - 0dB, 0x3 - -6dB)
bit 0 - 3: is handled in DAPM domain (DAPM_MIXER)
bit 4 - 5: has simple volume control
If there is no audio activity (BIAS_STANDBY), and
user changes the volume, than the output amplifier will
be enabled.
If the user changes the routing (but the codec remains in
BIAS_STANDBY), than the cached gain value also be written
to the register, which enables the amplifier.
The existing workaround for this is to have virtual
PGAs associated with the outputs, and whit DAPM PMD
the gain on the output will be forced to 0 (off) by
bypassing the regcache.
This failed to disable the amplifiers in several
scenario (as mentioned above).
Also if the codec is in BIAS_ON state, and user modifies
a volume control, which path is actually not enabled, than
that amplifier will be enabled as well, but it will
be not turned off, since there is no DAPM path, which
would make mute it.
To prevent amps being enabled, when they are not
needed, introduce the following workaround:
Track the state of each of this type of output.
In twl4030_write only allow actual write, when the
given output is enabled, otherwise only update
the reg_cache.
The PGA event handlers on power up will write the cached
value to the chip (restoring gain, routing selection).
On power down 0 is written to the register (disabling
the amp, and also just in case clearing the routing).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: remove duplicated #include
sh: Export uncached helper symbols.
sh: Fix up NUMA build for 29-bit.
serial: sh-sci: Fix build failure for non-sh architectures.
sh: Fix up uncached offset for legacy 29-bit mode.
sh: Support CPU affinity masks for INTC controllers.
Linus Torvalds [Fri, 19 Mar 2010 20:49:29 +0000 (13:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: fix compile errors in dma-mapping-common.h
alpha: remove trailing spaces in messages
alpha: use __ratelimit
Linus Torvalds [Fri, 19 Mar 2010 20:42:43 +0000 (13:42 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Remove IOMMU_VMERGE config option
powerpc: Fix swiotlb to respect the boot option
powerpc: Do not call prink when CONFIG_PRINTK is not defined
powerpc: Use correct ccr bit for syscall error status
powerpc/fsl-booke: Get coherent bit from PTE
powerpc/85xx: Make sure lwarx hint isn't set on ppc32
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty_port,usb-console: Fix usb serial console open/close regression
tty: cpm_uart: use resource_size()
tty_buffer: Fix distinct type warning
hvc_console: Fix race between hvc_close and hvc_remove
uartlite: Fix build on sparc.
tty: Take a 256 byte padding into account when buffering below sub-page units
Revert "tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call"
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: numa: fix BUILD_BUG_ON for node_read_distance
driver-core: document ERR_PTR() return values
kobject: documentation: Update to refer to kset-example.c.
sysdev: the cpu probe/release attributes should be sysdev_class_attributes
kobject: documentation: Fix erroneous example in kobject doc.
driver-core: fix missing kernel-doc in firmware_class
Driver core: Early platform kernel-doc update
sysfs: fix sysfs lockdep warning in mlx4 code
sysfs: fix sysfs lockdep warning in infiniband code
sysfs: fix sysfs lockdep warning in ipmi code
sysfs: Initialised pci bus legacy_mem field before use
sysfs: use sysfs_bin_attr_init in firmware class driver
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (45 commits)
USB: gadget/multi: cdc_do_config: remove redundant check
usb: r8a66597-hcd: fix removed from an attached hub
USB: xhci: Make endpoint interval debugging clearer.
USB: Fix usb_fill_int_urb for SuperSpeed devices
USB: cp210x: Remove double usb_control_msg from cp210x_set_config
USB: Remove last bit of CONFIG_USB_BERRY_CHARGE
USB: gadget: add gadget controller number for s3c-hsotg driver
USB: ftdi_sio: Fix locking for change_speed() function
USB: g_mass_storage: fixed module name in Kconfig
USB: gadget: f_mass_storage::fsg_bind(): fix error handling
USB: g_mass_storage: fix section mismatch warnings
USB: gadget: fix Blackfin builds after gadget cleansing
USB: goku_udc: remove potential null dereference
USB: option.c: Add Pirelli VID/PID and indicate Pirelli's modem interface is 0xff
USB: serial: Fix module name typo for qcaux Kconfig entry.
usb: cdc-wdm: Fix deadlock between write and resume
usb: cdc-wdm: Fix order in disconnect and fix locking
usb: cdc-wdm:Fix loss of data due to autosuspend
usb: cdc-wdm: Fix submission of URB after suspension
usb: cdc-wdm: Fix race between disconnect and debug messages
...
ASoC: remove a card from the list, if instantiation failed
If instantiation of a card failed, we still have to remove it from the
card list on unregistration. This fixes an Oops on Migo-R, triggering,
when after a failed firmware load attempt the driver modules are removed
and re-inserted again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Daniel Mack [Fri, 19 Mar 2010 14:52:55 +0000 (14:52 +0000)]
ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
Reported-by: Sven Neumann <s.neumann@raumfeld.com> Reported-by: Michael Hirsch <m.hirsch@raumfeld.com> Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds [Fri, 19 Mar 2010 16:43:06 +0000 (09:43 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (205 commits)
ceph: update for write_inode API change
ceph: reset osd after relevant messages timed out
ceph: fix flush_dirty_caps race with caps migration
ceph: include migrating caps in issued set
ceph: fix osdmap decoding when pools include (removed) snaps
ceph: return EBADF if waiting for caps on closed file
ceph: set osd request message front length correctly
ceph: reset front len on return to msgpool; BUG on mismatched front iov
ceph: fix snaptrace decoding on cap migration between mds
ceph: use single osd op reply msg
ceph: reset bits on connection close
ceph: remove bogus mds forward warning
ceph: remove fragile __map_osds optimization
ceph: fix connection fault STANDBY check
ceph: invalidate_authorizer without con->mutex held
ceph: don't clobber write return value when using O_SYNC
ceph: fix client_request_forward decoding
ceph: drop messages on unregistered mds sessions; cleanup
ceph: fix comments, locking in destroy_inode
ceph: move dereference after NULL test
...
Fix trivial conflicts in Documentation/ioctl/ioctl-number.txt
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: trivial white space
[CIFS] checkpatch cleanup
cifs: add cifs_revalidate_file
cifs: add a CIFSSMBUnixQFileInfo function
cifs: add a CIFSSMBQFileInfo function
cifs: overhaul cifs_revalidate and rename to cifs_revalidate_dentry
Daniel Mack [Sun, 28 Feb 2010 02:42:38 +0000 (10:42 +0800)]
ASoC: pxa-pcm-lib: initialize DMA channel to -1
This fixes a warning ("pxa_free_dma: trying to free channel 0 which is
already freed") when a device was opened but the hw_params() call
failed.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sarah Sharp [Tue, 16 Mar 2010 19:59:24 +0000 (12:59 -0700)]
USB: xhci: Make endpoint interval debugging clearer.
The xHCI hardware can only handle polling intervals that are a power of
two. When we add a new endpoint during a bandwidth allocation, and the
polling interval is rounded down to a power of two, print the original
polling interval in the endpoint descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Wilcox [Tue, 16 Mar 2010 19:55:44 +0000 (12:55 -0700)]
USB: Fix usb_fill_int_urb for SuperSpeed devices
USB 3 and Wireless USB specify a logarithmic encoding of the endpoint
interval that matches the USB 2 specification. usb_fill_int_urb() didn't
know that and was filling in the interval as if it was USB 1.1. Fix
usb_fill_int_urb() for SuperSpeed devices, but leave the wireless case
alone, because David Vrabel wants to keep the old encoding.
Update the struct urb kernel doc to note that SuperSpeed URBs must have
urb->interval specified in microframes.
Add a missing break statement in the usb_submit_urb() interrupt URB
checking, since wireless USB and SuperSpeed USB encode urb->interval
differently. This allows xHCI roothubs to actually register with khubd.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Brunner [Wed, 10 Mar 2010 22:26:37 +0000 (23:26 +0100)]
USB: cp210x: Remove double usb_control_msg from cp210x_set_config
This patch removes a double usb_control_msg that sets the cp210x
configuration registers a second time when calling cp210x_set_config.
For data sizes >2 the second write gets corrupted.
The patch has been created against 2.6.34-rc1, but all cp210x driver
revisions are affected.
Signed-off-by: Michael Brunner <mibru@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Contrary to the comment in fsg_add, fsg_bind calls fsg_unbind on errors,
which decreases refcount and frees the fsg_dev structure, causing trouble
when fsg_add does the same.
Fix it by simply leaving up cleanup to fsg_add().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit (0e530b45783f75) that moved usb_ep_autoconfig from the
__devinit section to the __init section missed the mass storage device.
Its fsg_bind() function uses the usb_ep_autoconfig() function from non
__init context leading to:
WARNING: drivers/usb/gadget/g_mass_storage.o(.text): Section mismatch in
reference from the function _fsg_bind()
to the function .init.text:_usb_ep_autoconfig()
So move fsg_bind() into __init as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Tue, 9 Mar 2010 05:35:22 +0000 (00:35 -0500)]
USB: gadget: fix Blackfin builds after gadget cleansing
The recent change to clean out dead gadget drivers (90f7976880bbbf99)
missed the call to gadget_is_musbhsfc() behind CONFIG_BLACKFIN. This
causes Blackfin gadget builds to fail since the function no longer
exists anywhere.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Fri, 12 Mar 2010 08:27:23 +0000 (10:27 +0200)]
USB: musb: fix warnings in Blackfin regs
The recent commit "usb: musb: Add context save and restore support" added
some stubs for the Blackfin code so things would compile, but it also
added a bunch of warnings due to missing return statements.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Fri, 12 Mar 2010 08:27:21 +0000 (10:27 +0200)]
usb: musb: abstract out ULPI_BUSCONTROL register reads/writes
The USB PHY on current Blackfin processors is a UTMI+ level 2 PHY.
However, it has no ULPI support - so there are no registers at all.
That means accesses to ULPI_BUSCONTROL have to be abstracted away
like other MUSB registers.
This fixes building for Blackfin parts again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Lindgren [Fri, 12 Mar 2010 08:35:20 +0000 (10:35 +0200)]
usb: musb: Fix compile error for omaps for musb_hdrc
CONFIG_ARCH_OMAP34XX is now CONFIG_ARCH_OMAP3.
But since drivers/usb/musb/omap2430.c use CONFIG_PM for these
registers and functions, do the same for the header.
Otherwise we get the following for most omap3 defconfigs:
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'while'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'while'
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andiry Xu [Fri, 12 Mar 2010 09:10:04 +0000 (17:10 +0800)]
USB: xHCI: re-initialize cmd_completion
When a signal interrupts a Configure Endpoint command, the cmd_completion used
in xhci_configure_endpoint() is not re-initialized and the
wait_for_completion_interruptible_timeout() will return failure. Initialize
cmd_completion in xhci_configure_endpoint().
Sonic Zhang [Mon, 8 Mar 2010 16:26:01 +0000 (11:26 -0500)]
USB: musb: fix build error introduced by isoc change
The recent commit "usb: musb: Fix for isochronous IN transfer" (f82a689fa)
seems to have been against an older kernel version. It uses the old style
naming of variables. Unfortunately, this breaks building for most MUSB
users out there since "bDesiredMode" has been renamed to "desired_mode".
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Acked-by: Anand Gadiyar <gadiyar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clemens Ladisch [Mon, 1 Mar 2010 16:18:56 +0000 (17:18 +0100)]
USB: EHCI: adjust ehci_iso_stream for changes in ehci_qh
The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either
an ehci_qh or an ehci_iso_stream structure, and uses the contents of the
hw_info1 field to distinguish the two cases.
After ehci_qh was split into hw and sw parts, ehci_iso_stream must also
be adjusted so that it again looks like an ehci_qh structure.
This fixes a NULL pointer access in ehci_endpoint_disable() when it
tries to access qh->hw->hw_info1.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com> Cc: stable <stable@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clemens Ladisch [Mon, 1 Mar 2010 08:12:50 +0000 (09:12 +0100)]
USB: EHCI: fix ITD list order
When isochronous URBs are shorter than one frame and when more than one
ITD in a frame has been completed before the interrupt can be handled,
scan_periodic() completes the URBs in the order in which they are found
in the descriptor list. Therefore, the descriptor list must contain the
ITDs in the correct order, i.e., a new ITD must be linked in after any
previous ITDs of the same endpoint.
This should fix garbled capture data in the USB audio drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Sat, 27 Feb 2010 15:24:49 +0000 (16:24 +0100)]
USB: serial: use port endpoint size to determine if ep is available
It is possible to have a multi-port device with a port lacking an in or
out bulk endpoint. Only checking for num_bulk_in or num_bulk_out is thus not
sufficient to determine whether a specific port has an in or out bulk
endpoint.
This fixes potential null pointer dereferences in the generic open and
write routines, as well as access to uninitialised fifo in write_room
and chars_in_buffer.
Also let write fail with ENODEV (instead of 0) on missing out endpoint
(also on zero-length writes).
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sat, 6 Mar 2010 20:04:03 +0000 (15:04 -0500)]
USB: fix usbfs regression
This patch (as1352) fixes a bug in the way isochronous input data is
returned to userspace for usbfs transfers. The entire buffer must be
copied, not just the first actual_length bytes, because the individual
packets will be discontiguous if any of them are short.
Reported-by: Markus Rechberger <mrechberger@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jason Wessel [Tue, 9 Mar 2010 03:50:11 +0000 (21:50 -0600)]
tty_port,usb-console: Fix usb serial console open/close regression
Commit e1108a63e10d344284011cccc06328b2cd3e5da3 ("usb_serial: Use the
shutdown() operation") breaks the ability to use a usb console
starting in 2.6.33. This was observed when using
console=ttyUSB0,115200 as a boot argument with an FTDI device. The
error is:
The handling of the ASYNCB_INITIALIZED changed in 2.6.32 such that in
tty_port_shutdown() it always clears the flag if it is set. The fix
is to add a variable to the tty_port struct to indicate when the tty
port is a console.
CC: Alan Cox <alan@linux.intel.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Oliver Neukum <oliver@neukum.org> CC: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fang Wenqi [Tue, 9 Mar 2010 10:54:28 +0000 (18:54 +0800)]
tty_buffer: Fix distinct type warning
CC drivers/char/tty_buffer.o
drivers/char/tty_buffer.c: In function ‘tty_insert_flip_string_fixed_flag’:
drivers/char/tty_buffer.c:251: warning: comparison of distinct pointer types lacks a cast
drivers/char/tty_buffer.c: In function ‘tty_insert_flip_string_flags’:
drivers/char/tty_buffer.c:288: warning: comparison of distinct pointer types lacks a cast
Fix it by replacing min() with min_t() in tty_insert_flip_string_flags and
tty_insert_flip_string_fixed_flag().
Amit Shah [Fri, 12 Mar 2010 06:23:15 +0000 (11:53 +0530)]
hvc_console: Fix race between hvc_close and hvc_remove
Alan pointed out a race in the code where hvc_remove is invoked. The
recent virtio_console work is the first user of hvc_remove().
Alan describes it thus:
The hvc_console assumes that a close and remove call can't occur at the
same time.
In addition tty_hangup(tty) is problematic as tty_hangup is asynchronous
itself....
So this can happen
hvc_close hvc_remove
hung up ? - no
lock
tty = hp->tty
unlock
lock
hp->tty = NULL
unlock
notify del
kref_put the hvc struct
close completes
tty is destroyed
tty_hangup dead tty
tty->ops will be NULL
NULL->...
This patch adds some tty krefs and also converts to using tty_vhangup().
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Amit Shah <amit.shah@redhat.com> CC: Alan Cox <alan@lxorguk.ukuu.org.uk> CC: linuxppc-dev@ozlabs.org CC: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Miller [Wed, 3 Mar 2010 10:50:26 +0000 (02:50 -0800)]
uartlite: Fix build on sparc.
We can get this driver enabled via MFD_TIMBERDALE which only
requires GPIO to be on.
But the of_address_to_resource() function is only present on
powerpc and microblaze, so we have to conditionalize the
CONFIG_OF probing bits on that.
Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mel Gorman [Tue, 2 Mar 2010 22:24:19 +0000 (22:24 +0000)]
tty: Take a 256 byte padding into account when buffering below sub-page units
The TTY layer takes some care to ensure that only sub-page allocations
are made with interrupts disabled. It does this by setting a goal of
"TTY_BUFFER_PAGE" to allocate. Unfortunately, while TTY_BUFFER_PAGE takes the
size of tty_buffer into account, it fails to account that tty_buffer_find()
rounds the buffer size out to the next 256 byte boundary before adding on
the size of the tty_buffer.
This patch adjusts the TTY_BUFFER_PAGE calculation to take into account the
size of the tty_buffer and the padding. Once applied, tty_buffer_alloc()
should not require high-order allocations.
Ari writes as the reason this should be reverted:
The problems with this patch include:
1. There's at least one subtlety I overlooked - switching
between X servers (i.e. from one X VT to another) still requires
the cooperation of both X servers. I was assuming that KMS
eliminated this.
2. It hasn't been tested at all (no X server patch exists which
uses the new mode).
As he was the original author of the patch, I'll revert it.
Cc: Ari Entlich <atrigent@ccs.neu.edu> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stephen Rothwell [Mon, 15 Mar 2010 23:33:32 +0000 (10:33 +1100)]
sysdev: the cpu probe/release attributes should be sysdev_class_attributes
This fixes these warnings:
drivers/base/cpu.c:264: warning: initialization from incompatible pointer type
drivers/base/cpu.c:265: warning: initialization from incompatible pointer type
This fixes a sysfs lockdep warning in the ipmi code.
Thanks to Eric Biederman and Yinghai Lu for the original versions of the
patch, unfortunatly they did not submit them in a form they could be
applied in.
Cc: Yinghai Lu <yinghai@kernel.org> Cc: Eric Biederman <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mel Gorman [Wed, 10 Mar 2010 22:48:34 +0000 (22:48 +0000)]
sysfs: Initialised pci bus legacy_mem field before use
PPC64 is failing to boot the latest mmotm due to an uninitialised pointer in
pci_create_legacy_files(). The surprise is that machines boot at all and it
would appear to affect current mainline as well. This patch fixes the problem.
Mark Brown [Tue, 16 Mar 2010 16:11:14 +0000 (16:11 +0000)]
ASoC: Hook up microphone jack detection on 1133-EV1 board
Note that since all the microphones share a bias there is a single
jack exported for all three, even though there are two physical
connectors plus the soldered down silicon mic. Note also that the SiMic
is always present by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Barry Song [Fri, 19 Mar 2010 03:18:40 +0000 (11:18 +0800)]
ASoC: change bf5xx-ad1938 machine driver to bf5xx-ad193x machine driver
Signed-off-by: Barry Song <21cnbao@gmail.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Barry Song [Fri, 19 Mar 2010 06:48:33 +0000 (14:48 +0800)]
ASoC: rename ad1938 to ad193x and add support for ad1936/7/8/9
Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Yi Li <yi.li@analog.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>