PM / Sleep: Mark devices involved in wakeup signaling during suspend
The generic PM domains code in drivers/base/power/domain.c has
to avoid powering off domains that provide power to wakeup devices
during system suspend. Currently, however, this only works for
wakeup devices directly belonging to the given domain and not for
their children (or the children of their children and so on).
Thus, if there's a wakeup device whose parent belongs to a power
domain handled by the generic PM domains code, the domain will be
powered off during system suspend preventing the device from
signaling wakeup.
To address this problem introduce a device flag, power.wakeup_path,
that will be set during system suspend for all wakeup devices,
their parents, the parents of their parents and so on. This way,
all wakeup paths in the device hierarchy will be marked and the
generic PM domains code will only need to avoid powering off
domains containing devices whose power.wakeup_path is set.
PM / Domains: Split device PM domain data into base and need_restore
The struct pm_domain_data data type is defined in such a way that
adding new fields specific to the generic PM domains code will
require include/linux/pm.h to be modified. As a result, data types
used only by the generic PM domains code will be defined in two
headers, although they all should be defined in pm_domain.h and
pm.h will need to include more headers, which won't be very nice.
For this reason change the definition of struct pm_subsys_data
so that its domain_data member is a pointer, which will allow
struct pm_domain_data to be subclassed by various PM domains
implementations. Remove the need_restore member from
struct pm_domain_data and make the generic PM domains code
subclass it by adding the need_restore member to the new data type.
Merge commit e8b364b88cc4001b21c28c1ecf1e1e3ffbe162e6
(PM / Clocks: Do not acquire a mutex under a spinlock) fixing
a regression in drivers/base/power/clock_ops.c.
PM / Clocks: Do not acquire a mutex under a spinlock
Commit b7ab83e (PM: Use spinlock instead of mutex in clock
management functions) introduced a regression causing clocks_mutex
to be acquired under a spinlock. This happens because
pm_clk_suspend() and pm_clk_resume() call pm_clk_acquire() under
pcd->lock, but pm_clk_acquire() executes clk_get() which causes
clocks_mutex to be acquired. Similarly, __pm_clk_remove(),
executed under pcd->lock, calls clk_put(), which also causes
clocks_mutex to be acquired.
To fix those problems make pm_clk_add() call pm_clk_acquire(), so
that pm_clk_suspend() and pm_clk_resume() don't have to do that.
Change pm_clk_remove() and pm_clk_destroy() to separate
modifications of the pcd->clock_list list from the actual removal of
PM clock entry objects done by __pm_clk_remove().
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Magnus Damm [Sun, 25 Sep 2011 21:20:49 +0000 (23:20 +0200)]
ARM: mach-shmobile: sh7372 A3SM support
This patch adds sh7372 A3SM power domain support.
The sh7372 A3SM hardware power domain contains the
ARM Cortex-A8 CPU Core including L2 cache. This
sleep mode can be seen as a one step deeper sleep
mode from the already existing Core Standby mode.
To wake up from A3SM sleep only a few wakeup sources
are supported - so the regular INTC controller will
not be able to help us unfortunately.
The code in this patch will enter A3SM sleep via the
regular Suspend-to-RAM interface in the case of only
wakeups supported by A3SM are enabled. If unsupported
wakeups are enabled then Core Standby will be used
instead.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Merge branch 'spi/merge' of git://git.secretlab.ca/git/linux-2.6
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
spi: Fix WARN when removing spi-fsl-spi module
spi/imx: Fix spi-imx when the hardware SPI chipselects are used
Jeff Harris [Fri, 23 Sep 2011 15:49:36 +0000 (11:49 -0400)]
spi: Fix WARN when removing spi-fsl-spi module
If CPM mode is not used, the fsl_dummy_rx variable is never allocated. When
the cleanup attempts to free it, the reference count is zero and a WARN is
generated. The same CPM mode check used in the initialize is applied to the
free as well.
Tested on 2.6.33 with the previous spi_mpc8xxx driver. The renamed
spi-fsl-spi driver looks to have the same problem.
Signed-off-by: Jeff Harris <jeff_harris@kentrox.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Merge branch 'perf-tools-for-linus' of git://github.com/acmel/linux
* 'perf-tools-for-linus' of git://github.com/acmel/linux:
perf tools: Add support for disabling -Werror via WERROR=0
perf top: Fix userspace sample addr map offset
perf symbols: Fix issue with binaries using 16-bytes buildids (v2)
perf tool: Fix endianness handling of u32 data in samples
perf sort: Fix symbol sort output by separating unresolved samples by type
perf symbols: Synthesize anonymous mmap events
perf record: Create events initially disabled and enable after init
perf symbols: Add some heuristics for choosing the best duplicate symbol
perf symbols: Preserve symbol scope when parsing /proc/kallsyms
perf symbols: /proc/kallsyms does not sort module symbols
perf symbols: Fix ppc64 SEGV in dso__load_sym with debuginfo files
perf probe: Fix regression of variable finder
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: fix DDIA enable on some rs690 systems
Revert "drm/radeon/kms: fix typo in r100_blit_copy"
Merge branch 'for-linus' of git://github.com/tiwai/sound
* 'for-linus' of git://github.com/tiwai/sound:
ALSA: usb-audio - clear chip->probing on error exit
ALSA: fm801: Gracefully handle failure of tuner auto-detect
ALSA: fm801: Fix double free in case of error in tuner detection
ASoC: Ensure we generate a driver name
ASoC: Remove bitrotted wm8962_resume()
ASoC: bf5xx-ad73311: Fix prototype for bf5xx_probe
Darren Hart [Thu, 8 Sep 2011 20:42:39 +0000 (13:42 -0700)]
perf tools: Add support for disabling -Werror via WERROR=0
GCC often introduces new warnings with lots of false positives -
breaking -Werror builds. WERROR=0 allows one to build perf without much
fuss - while still encouraging people to send patches to avoid the fuss
of having to type WERROR=0.
Bisecting back to commits that produce a (mostly harmless) warning on
some compilers is more difficult. With WERROR=0 one could bisect without
worrying about harmless warnings.
The 'perf top' tool came from the kernel where we had each DSO (vmlinux,
modules) loaded just once at a time.
But userspace may have DSOs loaded in multiple addresses (shared
libraries), requiring that we use the just resolved map instead of the
first one found.
Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/n/tip-ag53wz0yllpgers0n2w7hchp@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stephane Eranian [Fri, 22 Oct 2010 15:25:01 +0000 (17:25 +0200)]
perf symbols: Fix issue with binaries using 16-bytes buildids (v2)
Buildid can vary in size. According to the man page of ld, buildid can
be 160 bits (sha1) or 128 bits (md5, uuid). Perf assumes buildid size of
20 bytes (160 bits) regardless. When dealing with md5 buildids, it would
thus read more than needed and that would cause mismatches and samples
without symbols.
This patch fixes this by taking into account the actual buildid size as
encoded int he section header. The leftover bytes are also cleared.
This second version fixes a minor issue with the memset() base position.
Cc: David S. Miller <davem@davemloft.net> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert Richter <robert.richter@amd.com> Cc: Stephane Eranian <eranian@gmail.com> Link: http://lkml.kernel.org/r/4cc1af3c.8ee7d80a.5a28.ffff868e@mx.google.com Signed-off-by: Stephane Eranian <eranian@google.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
David Ahern [Tue, 6 Sep 2011 15:12:26 +0000 (09:12 -0600)]
perf tool: Fix endianness handling of u32 data in samples
Currently, analyzing PPC data files on x86 the cpu field is always 0 and
the tid and pid are backwards. For example, analyzing a PPC file on PPC
the pid/tid fields show:
rsyslogd 1210/1212
and analyzing the same PPC file using an x86 perf binary shows:
rsyslogd 1212/1210
The problem is that the swap_op method for samples is
perf_event__all64_swap which assumes all elements in the sample_data
struct are u64s. cpu, tid and pid are u32s and need to be handled
individually. Given that the swap is done before the sample is parsed,
the simplest solution is to undo the 64-bit swap of those elements when
the sample is parsed and do the proper swap.
The RAW data field is generic and perf cannot have programmatic knowledge
of how to treat that data. Instead a warning is given to the user.
Thanks to Anton Blanchard for providing a data file for a mult-CPU
PPC system so I could verify the fix for the CPU fields.
v3 -> v4:
- fixed use of WARN_ONCE
v2 -> v3:
- used WARN_ONCE for message regarding raw data
- removed struct wrapper around union
- fixed whitespace issues
v1 -> v2:
- added a union for undoing the byte-swap on u64 and redoing swap on
u32's to address compiler errors (see git commit 65014ab3)
Cc: Anton Blanchard <anton@samba.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1315321946-16993-1-git-send-email-dsahern@gmail.com Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Using perf stat to get the user/kernel/hypervisor breakdown contradicted
this.
The problem is we merge all unresolved samples into the one unknown
bucket. If add a comparison by sample type to sort__sym_cmp we get the
real picture:
This happens because we aren't consistent with our sorting. On
one hand we check to see if both symbols match and for two unresolved
samples sym is NULL so we match:
if (left->ms.sym == right->ms.sym)
return 0;
On the other hand we use sample IP for unresolved samples when
comparing against a symbol:
Acked-by: Eric B Munson <emunson@mgebm.net> Cc: Eric B Munson <emunson@mgebm.net> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Ian Munsie <imunsie@au1.ibm.com> Link: http://lkml.kernel.org/r/20110831115145.4f598ab2@kryten Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Anton Blanchard [Mon, 29 Aug 2011 23:15:06 +0000 (09:15 +1000)]
perf symbols: Synthesize anonymous mmap events
perf_event__synthesize_mmap_events does not create anonymous mmap events
even though the kernel does. As a result an already running application
with dynamically created code will not get profiled - all samples end up
in the unknown bucket.
This patch skips any entries with '[' in the name to avoid adding events
for special regions (eg the vsyscall page). All other executable mmaps
are assumed to be anonymous and an event is synthesized.
Acked-by: Pekka Enberg <penberg@kernel.org> Cc: Eric B Munson <emunson@mgebm.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Link: http://lkml.kernel.org/r/20110830091506.60b51fe8@kryten Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
David Ahern [Thu, 25 Aug 2011 16:17:55 +0000 (10:17 -0600)]
perf record: Create events initially disabled and enable after init
perf-record currently creates events enabled. When doing a system wide
collection (-a arg) this causes data collection for perf's
initialization activities -- eg., perf_event__synthesize_threads().
For some events (e.g., context switch S/W event or tracepoints like
syscalls) perf's initialization causes a lot of events to be captured
frequently generating "Check IO/CPU overload!" warnings on larger
systems (e.g., 2 socket, quad core, hyperthreading).
perf's initialization phase can be skipped by creating events
disabled and then enabling them once the initialization is done.
Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1314289075-14706-1-git-send-email-dsahern@gmail.com Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Anton Blanchard [Wed, 24 Aug 2011 06:40:17 +0000 (16:40 +1000)]
perf symbols: Add some heuristics for choosing the best duplicate symbol
Try and pick the best symbol based on a few heuristics:
- Prefer a non weak symbol over a weak one
- Prefer a global symbol over a non global one
- Prefer a symbol with less underscores (idea taken from kallsyms.c)
- If all else fails, choose the symbol with the longest name
Cc: Eric B Munson <emunson@mgebm.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20110824065243.161953371@samba.org Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Anton Blanchard [Wed, 24 Aug 2011 06:40:16 +0000 (16:40 +1000)]
perf symbols: Preserve symbol scope when parsing /proc/kallsyms
kallsyms__parse capitalises the symbol type, so every symbol is marked
global. Remove this and fix symbol_type__is_a to handle both local and
global symbols.
Cc: Eric B Munson <emunson@mgebm.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20110824065243.077125989@samba.org Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Some symbols end up with a negative length and others have a length
larger than they should. This results in confusing perf output.
We already have a function to fixup the end of zero length symbols so
use that instead.
Cc: Eric B Munson <emunson@mgebm.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/20110824065242.969681349@samba.org Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Masami Hiramatsu [Sat, 20 Aug 2011 05:39:23 +0000 (14:39 +0900)]
perf probe: Fix regression of variable finder
Fix to call convert_variable() if previous call does not fail.
To call convert_variable, it ensures "ret" is 0. However, since
"ret" has the return value of synthesize_perf_probe_arg() which
always returns positive value if it succeeded, perf probe doesn't
call convert_variable(). This will cause a SEGV when we add an
event with arguments.
This has to be fixed as it ensures "ret" is greater than 0
(or not negative).
This regression has been introduced by my previous patch, f182e3e1.
Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Pekka Enberg <penberg@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: yrl.pp-manager.tt@hitachi.com Link: http://lkml.kernel.org/r/20110820053922.3286.65805.stgit@fedora15 Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Thomas Pfaff [Thu, 22 Sep 2011 16:26:06 +0000 (18:26 +0200)]
ALSA: usb-audio - clear chip->probing on error exit
The Terratec Aureon 5.1 USB sound card support is broken since kernel
2.6.39.
2.6.39 introduced power management support for USB sound cards that added
a probing flag in struct snd_usb_audio.
During the probe of the card it gives following error message :
usb 7-2: new full speed USB device number 2 using uhci_hcd
cannot find UAC_HEADER
snd-usb-audio: probe of 7-2:1.3 failed with error -5
input: USB Audio as
/devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.3/input/input6
generic-usb 0003:0CCD:0028.0001: input: USB HID v1.00 Device [USB Audio]
on usb-0000:00:1d.1-2/input3
I can not comment about that "cannot find UAC_HEADER" error, but until
2.6.38 the card worked anyway.
With 2.6.39 chip->probing remains 1 on error exit, and any later ioctl
stops in snd_usb_autoresume with -ENODEV.
Alex Deucher [Thu, 22 Sep 2011 14:47:23 +0000 (10:47 -0400)]
drm/radeon/kms: fix DDIA enable on some rs690 systems
DVOOutputControl checks the value of of bios scratch reg 3
on some tables and assumes the encoder is already enabled
if the DFP2_ACTIVE bit is set. Clear that bit so the table
sets the DDIA enable bit properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge branch 'for-linus' of git://git.selinuxproject.org/~jmorris/linux-security
* 'for-linus' of git://git.selinuxproject.org/~jmorris/linux-security:
TPM: Zero buffer after copying to userspace
TPM: Call tpm_transmit with correct size
TPM: tpm_nsc: Fix a double free of pdev in cleanup_nsc
TPM: TCG_ATMEL should depend on HAS_IOPORT
Peter Huewe [Thu, 15 Sep 2011 17:37:43 +0000 (14:37 -0300)]
TPM: Call tpm_transmit with correct size
This patch changes the call of tpm_transmit by supplying the size of the
userspace buffer instead of TPM_BUFSIZE.
This got assigned CVE-2011-1161.
[The first hunk didn't make sense given one could expect
way less data than TPM_BUFSIZE, so added tpm_transmit boundary
check over bufsiz instead
The last parameter of tpm_transmit() reflects the amount
of data expected from the device, and not the buffer size
being supplied to it. It isn't ideal to parse it directly,
so we just set it to the maximum the input buffer can handle
and let the userspace API to do such job.]
drivers/char/tpm/tpm_atmel.h: In function ‘atmel_get_base_addr’:
drivers/char/tpm/tpm_atmel.h:129: error: implicit declaration of function ‘ioport_map’
drivers/char/tpm/tpm_atmel.h:129: warning: return makes pointer from integer without a cast
The code in tpm_atmel.h supports PPC64 (using the device tree and ioremap())
and "anything else" (using ioport_map()). However, ioportmap() is only
available on platforms that set HAS_IOPORT.
Although PC64 seems to have HAS_IOPORT, a "depends on HAS_IOPORT" should work,
but I think it's better to expose the special PPC64 handling explicit using
"depends on PPC64 || HAS_IOPORT".
zorro: Defer device_register() until all devices have been identified
As the Amiga Zorro II address space is limited to 8.5 MiB and Zorro
devices can contain only one BAR, several Amiga Zorro II expansion
boards (mainly graphics cards) contain multiple Zorro devices: a small
one for the control registers and one (or more) for the graphics memory.
The conversion of cirrusfb to the new driver framework introduced a
regression: the driver contains a zorro_driver for the first Zorro
device, and uses the (old) zorro_find_device() call to find the second
Zorro device.
However, as the Zorro core calls device_register() as soon as a Zorro
device is identified, it may not have identified the second Zorro device
belonging to the same physical Zorro expansion card. Hence cirrusfb
could no longer find the second part of the Picasso II graphics card,
causing a NULL pointer dereference.
Defer the registration of Zorro devices with the driver framework until
all Zorro devices have been identified to fix this.
Note that the alternative solution (modifying cirrusfb to register a
zorro_driver for all Zorro devices belonging to a graphics card, instead
of only for the first one, and adding a synchronization mechanism to
defer initialization until all have been found), is not an option, as on
some cards one device may be optional (e.g. the second bank of 2 MiB of
graphics memory on the Picasso IV in Zorro II mode).
Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] kvm: extension capability for new address space layout
[S390] kvm: fix address mode switching
Ben Hutchings [Thu, 22 Sep 2011 13:39:52 +0000 (14:39 +0100)]
ALSA: fm801: Gracefully handle failure of tuner auto-detect
Commit 9676001559fce06e37c7dc230ab275f605556176
("ALSA: fm801: add error handling if auto-detect fails") seems to
break systems that were previously working without a tuner.
As a bonus, this should fix init and cleanup for the case where the
tuner is explicitly disabled.
Reported-and-tested-by: Hor Jiun Shyong <jiunshyong@gmail.com>
References: http://bugs.debian.org/641946 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: stable@kernel.org [v3.0+] Signed-off-by: Takashi Iwai <tiwai@suse.de>
Once we have successfully called snd_device_new(), the cleanup
function fm801_free() will automatically be called by snd_card_free()
and we must *not* also call fm801_free() directly.
Reported-by: Hor Jiun Shyong <jiunshyong@gmail.com>
References: http://bugs.debian.org/641946 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: stable@kernel.org [v3.0+] Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lasse Collin [Wed, 21 Sep 2011 14:30:50 +0000 (17:30 +0300)]
XZ: Fix incorrect XZ_BUF_ERROR
xz_dec_run() could incorrectly return XZ_BUF_ERROR if all of the
following was true:
- The caller knows how many bytes of output to expect and only provides
that much output space.
- When the last output bytes are decoded, the caller-provided input
buffer ends right before the LZMA2 end of payload marker. So LZMA2
won't provide more output anymore, but it won't know it yet and thus
won't return XZ_STREAM_END yet.
- A BCJ filter is in use and it hasn't left any unfiltered bytes in the
temp buffer. This can happen with any BCJ filter, but in practice
it's more likely with filters other than the x86 BCJ.
This fixes <https://bugzilla.redhat.com/show_bug.cgi?id=735408> where
Squashfs thinks that a valid file system is corrupt.
This also fixes a similar bug in single-call mode where the uncompressed
size of a block using BCJ + LZMA2 was 0 bytes and caller provided no
output space. Many empty .xz files don't contain any blocks and thus
don't trigger this bug.
This also tweaks a closely related detail: xz_dec_bcj_run() could call
xz_dec_lzma2_run() to decode into temp buffer when it was known to be
useless. This was harmless although it wasted a minuscule number of CPU
cycles.
* git://github.com/davem330/net: (27 commits)
xfrm: Perform a replay check after return from async codepaths
fib:fix BUG_ON in fib_nl_newrule when add new fib rule
ixgbe: fix possible null buffer error
tg3: fix VLAN tagging regression
net: pxa168: Fix build errors by including interrupt.h
netconsole: switch init_netconsole() to late_initcall
gianfar: Fix overflow check and return value for gfar_get_cls_all()
ppp_generic: fix multilink fragment MTU calculation (again)
GRETH: avoid overwrite IP-stack's IP-frags checksum
GRETH: RX/TX bytes were never increased
ipv6: fix a possible double free
b43: Fix beacon problem in ad-hoc mode
Bluetooth: add support for 2011 mac mini
Bluetooth: Add MacBookAir4,1 support
Bluetooth: Fixed BT ST Channel reg order
r8169: do not enable the TBI for anything but the original 8169.
r8169: remove erroneous processing of always set bit.
r8169: fix WOL setting for 8105 and 8111evl
r8169: add MODULE_FIRMWARE for the firmware of 8111evl
r8169: fix the reset setting for 8111evl
...
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block:
floppy: use del_timer_sync() in init cleanup
blk-cgroup: be able to remove the record of unplugged device
block: Don't check QUEUE_FLAG_SAME_COMP in __blk_complete_request
mm: Add comment explaining task state setting in bdi_forker_thread()
mm: Cleanup clearing of BDI_pending bit in bdi_forker_thread()
block: simplify force plug flush code a little bit
block: change force plug flush call order
block: Fix queue_flag update when rq_affinity goes from 2 to 1
block: separate priority boosting from REQ_META
block: remove READ_META and WRITE_META
xen-blkback: fixed indentation and comments
xen-blkback: Don't disconnect backend until state switched to XenbusStateClosed.
init: carefully handle loglevel option on kernel cmdline.
When a malformed loglevel value (for example "${abc}") is passed on the
kernel cmdline, the loglevel itself is being set to 0.
That then suppresses all following messages, including all the errors
and crashes caused by other malformed cmdline options. This could make
debugging process quite tricky.
This patch leaves the previous value of loglevel if the new value is
incorrect and reports an error code in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@sysgo.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Tue, 20 Sep 2011 22:19:41 +0000 (15:19 -0700)]
teach /proc/$pid/numa_maps about transparent hugepages
This is modeled after the smaps code.
It detects transparent hugepages and then does a single gather_stats()
for the page as a whole. This has two benifits:
1. It is more efficient since it does many pages in a single shot.
2. It does not have to break down the huge page.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Tue, 20 Sep 2011 22:19:39 +0000 (15:19 -0700)]
break out numa_maps gather_pte_stats() checks
gather_pte_stats() does a number of checks on a target page
to see whether it should even be considered for statistics.
This breaks that code out in to a separate function so that
we can use it in the transparent hugepage case in the next
patch.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Acked-by: Hugh Dickins <hughd@google.com> Reviewed-by: Christoph Lameter <cl@gentwo.org> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Hansen [Tue, 20 Sep 2011 22:19:38 +0000 (15:19 -0700)]
make /proc/$pid/numa_maps gather_stats() take variable page size
We need to teach the numa_maps code about transparent huge pages. The
first step is to teach gather_stats() that the pte it is dealing with
might represent more than one page.
Note that will we use this in a moment for transparent huge pages since
they have use a single pmd_t which _acts_ as a "surrogate" for a bunch
of smaller pte_t's.
I'm a _bit_ unhappy that this interface counts in hugetlbfs page sizes
for hugetlbfs pages and PAGE_SIZE for normal pages. That means that to
figure out how many _bytes_ "dirty=1" means, you must first know the
hugetlbfs page size. That's easier said than done especially if you
don't have visibility in to the mount.
But, that's probably a discussion for another day especially since it
would change behavior to fix it. But, just in case anyone wonders why
this patch only passes a '1' in the hugetlb case...
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xfrm: Perform a replay check after return from async codepaths
When asyncronous crypto algorithms are used, there might be many
packets that passed the xfrm replay check, but the replay advance
function is not called yet for these packets. So the replay check
function would accept a replay of all of these packets. Also the
system might crash if there are more packets in async processing
than the size of the anti replay window, because the replay advance
function would try to update the replay window beyond the bounds.
This pach adds a second replay check after resuming from the async
processing to fix these issues.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
fib:fix BUG_ON in fib_nl_newrule when add new fib rule
add new fib rule can cause BUG_ON happen
the reproduce shell is
ip rule add pref 38
ip rule add pref 38
ip rule add to 192.168.3.0/24 goto 38
ip rule del pref 38
ip rule add to 192.168.3.0/24 goto 38
ip rule add pref 38
then the BUG_ON will happen
del BUG_ON and use (ctarget == NULL) identify whether this rule is unresolved
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Brown [Tue, 20 Sep 2011 10:41:54 +0000 (11:41 +0100)]
ASoC: Ensure we generate a driver name
Commit 873bd4c (ASoC: Don't set invalid name string to snd_card->driver
field) broke generation of a driver name for all ASoC cards relying on the
automatic generation of one. Fix this by using the old default with spaces
replaced by underscores.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Takashi Iwai <tiwai@suse.de>
It seems that at least one PPC machine would occasionally give a (valid) 0 as
the return value from dma_map, this caused the ixgbe code to not work
correctly. A fix is pending in the PPC tree to not return 0 from dma map, but
we can also fix the driver to make sure we don't mess up in other arches as
well.
This patch is applicable to all current stable kernels.
Reported-by: Neil Horman <nhorman@redhat.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Alexander Duyck <alexander.h.duyck@intel.com> CC: stable@kernel.org Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
broke VLAN tagging on outbound packets.
It ifdef'ed BCM_KERNEL_SUPPORTS_8021Q, but this
is not set anywhere. So vlan never gets set, and
all packets are sent with vlan=0.
v2: We can just remove the test. vlan_tx_tag_present
is valid regardless of whether the 802.1q module
is built.
Tested on BCM5721 rev 11.
Signed-off-by: Kasper Pedersen <kernel@kasperkp.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'fixes' of git://git.linaro.org/people/arnd/arm-soc
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc:
mach-integrator: fix VGA base regression
arm/dt: Tegra: Update SDHCI nodes to match bindings
ARM: EXYNOS4: fix incorrect pad configuration for keypad row lines
ARM: SAMSUNG: fix to prevent declaring duplicated
ARM: SAMSUNG: fix watchdog reset issue with clk_get()
ARM: S3C64XX: Remove un-used code backlight code on SMDK6410
ARM: EXYNOS4: restart clocksource while system resumes
ARM: EXYNOS4: Fix routing timer interrupt to offline CPU
ARM: EXYNOS4: Fix return type of local_timer_setup()
ARM: EXYNOS4: Fix wrong pll type for vpll
ARM: Dove: fix second SPI initialization call
After commit c5f5c4db3938 ("staging: zcache: fix crash on high memory
swap") cleancache crashes on the first successful get. This was caused
by a remaining virt_to_page() call in zcache_pampd_get_data_and_free()
that only gets run in the cleancache path.
The patch converts the virt_to_page() to struct page casting like was
done for other instances in c5f5c4db3938.
Makes the Integrator/AP freeze completely. I appears that
this is due to the VGA base address being assigned at PCI
init time, while this base is needed earlier than that.
Moving the initialization of the base address to the
.map_io function solves this problem.
Cc: Rob Herring <rob.herring@calxeda.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
drivers/net/pxa168_eth.c: In function 'pxa168_eth_collect_events':
drivers/net/pxa168_eth.c:866: error: 'IRQ_NONE' undeclared (first use in this function)
drivers/net/pxa168_eth.c:866: error: (Each undeclared identifier is reported only once
drivers/net/pxa168_eth.c:866: error: for each function it appears in.)
drivers/net/pxa168_eth.c: At top level:
drivers/net/pxa168_eth.c:913: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'pxa168_eth_int_handler'
drivers/net/pxa168_eth.c: In function 'pxa168_eth_open':
drivers/net/pxa168_eth.c:1133: error: implicit declaration of function 'request_irq'
drivers/net/pxa168_eth.c:1133: error: 'pxa168_eth_int_handler' undeclared (first use in this function)
drivers/net/pxa168_eth.c:1134: error: 'IRQF_DISABLED' undeclared (first use in this function)
drivers/net/pxa168_eth.c:1160: error: implicit declaration of function 'free_irq'
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lin Ming [Tue, 20 Sep 2011 19:45:07 +0000 (15:45 -0400)]
netconsole: switch init_netconsole() to late_initcall
Commit 88491d8(drivers/net: Kconfig & Makefile cleanup) causes a
regression that netconsole does not work if netconsole and network
device driver are build into kernel, because netconsole is linked
before network device driver.
Andrew Morton suggested to fix this with initcall ordering.
Fixes it by switching init_netconsole() to late_initcall.
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 6 Sep 2011 12:44:25 +0000 (12:44 +0000)]
gianfar: Fix overflow check and return value for gfar_get_cls_all()
This function may currently fill one entry beyond the end of the
array it is given. It also doesn't return an error code in case
it does detect overflow.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Henry Wong [Sun, 18 Sep 2011 13:41:49 +0000 (13:41 +0000)]
ppp_generic: fix multilink fragment MTU calculation (again)
When using MLPPP, the maximum size of a fragment is incorrectly
calculated with an offset of -2.
This patch reverses the changes in the patch found here:
http://marc.info/?l=linux-netdev&m=123541324010539&w=2
The value of hdrlen includes the size of both the 2-byte PPP protocol
field and the 2- or 4-byte multilink header (2+4=6 for long sequence
numbers, 2+2=4 for short sequence numbers). Section 2 of RFC1661 says
that the MRU that is negotiated (i.e., the MTU of the sending system)
includes only the PPP payload but not the protocol field, thus the
correct MTU should be the link's MTU minus the multilink header (mtu -
(hdrlen-2)).
The incorrect calculation causes Linux to fragment packets to a size two
bytes smaller than the allowed MTU. While not technically illegal, this
behaviour confounds MRU-tuning to avoid PPP-layer fragmentation.
Signed-off-by: Henry Wong <henry@stuffedcow.net> Signed-off-by: David S. Miller <davem@davemloft.net>
The GRETH GBIT core does not do checksum offloading for IP
segmentation. This patch adds a check in the xmit function to
determine if the stack has calculated the checksum for us.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roy Li [Tue, 20 Sep 2011 19:10:16 +0000 (15:10 -0400)]
ipv6: fix a possible double free
When calling snmp6_alloc_dev fails, the snmp6 relevant memory
are freed by snmp6_alloc_dev. Calling in6_dev_finish_destroy
will free these memory twice.
Double free will lead that undefined behavior occurs.
Signed-off-by: Roy Li <rongqing.li@windriver.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix broken sec=ntlmv2/i sec option (try #2)
Fix the conflict between rwpidforward and rw mount options
CIFS: Fix ERR_PTR dereference in cifs_get_root
cifs: fix possible memory corruption in CIFSFindNext
[S390] kvm: extension capability for new address space layout
598841ca9919d008b520114d8a4378c4ce4e40a1 ([S390] use gmap address
spaces for kvm guest images) changed kvm on s390 to use a separate
address space for kvm guests. We can now put KVM guests anywhere
in the user address mode with a size up to 8PB - as long as the
memory is 1MB-aligned. This change was done without KVM extension
capability bit.
The change was added after 3.0, but we still have a chance to add
a feature bit before 3.1 (keeping the releases in a sane state).
We use number 71 to avoid collisions with other pending kvm patches
as requested by Alexander Graf.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Avi Kivity <avi@redhat.com> Cc: Alexander Graf <agraf@suse.de> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
598841ca9919d008b520114d8a4378c4ce4e40a1 ([S390] use gmap address
spaces for kvm guest images) changed kvm to use a separate address
space for kvm guests. This address space was switched in __vcpu_run
In some cases (preemption, page fault) there is the possibility that
this address space switch is lost.
The typical symptom was a huge amount of validity intercepts or
random guest addressing exceptions.
Fix this by doing the switch in sie_loop and sie_exit and saving the
address space in the gmap structure itself. Also use the preempt
notifier.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Avi Kivity <avi@redhat.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
John Crispin [Wed, 24 Aug 2011 08:31:39 +0000 (10:31 +0200)]
watchdog: lantiq: fix watchdogs timeout handling
The enable function was using the global timeout variable for local operations.
This resulted in the value of the global variable being corrupted, thus
breaking the code.
Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Thomas Langer <thomas.langer@lantiq.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: linux-watchdog@vger.kernel.org Cc: linux-mips@linux-mips.org
On platforms with no iCRU support don't print two, (possibly conflicting),
"NMI occurred" messages when the firmware is unable to source the NMI.
Please note that one of the enhancements to the v1.3.0 hpwdt driver is to panic and allow
KDUMP to succeed even on NMIs that are unknown to the platform firmware.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com> Reviewed-by: Thomas Mingarelli <thomas.mingarelli@hp.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
watchdog: WatchDog Timer Driver Core - use passed watchdog_device
Use the passed watchdog_device instead of the static global variable when
testing and setting the status in watchdog_ping, watchdog_start, and
watchdog_stop. Note that the callers of these functions are actually
passing the static global variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Steve French [Mon, 29 Aug 2011 18:54:12 +0000 (18:54 +0000)]
Fix the conflict between rwpidforward and rw mount options
Both these options are started with "rw" - that's why the first one
isn't switched on even if it is specified. Fix this by adding a length
check for "rw" option check.
Cc: <stable@kernel.org> Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Layton [Tue, 23 Aug 2011 11:21:28 +0000 (07:21 -0400)]
cifs: fix possible memory corruption in CIFSFindNext
The name_len variable in CIFSFindNext is a signed int that gets set to
the resume_name_len in the cifs_search_info. The resume_name_len however
is unsigned and for some infolevels is populated directly from a 32 bit
value sent by the server.
If the server sends a very large value for this, then that value could
look negative when converted to a signed int. That would make that
value pass the PATH_MAX check later in CIFSFindNext. The name_len would
then be used as a length value for a memcpy. It would then be treated
as unsigned again, and the memcpy scribbles over a ton of memory.
Fix this by making the name_len an unsigned value in CIFSFindNext.
Cc: <stable@kernel.org> Reported-by: Darren Lavender <dcl@hppine99.gbr.hp.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Merge branch 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip
* 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86, iommu: Mark DMAR IRQ as non-threaded
genirq: Make irq_shutdown() symmetric vs. irq_startup again
Merge branch 'for-linus' of git://github.com/chrismason/linux
* 'for-linus' of git://github.com/chrismason/linux:
Btrfs: only clear the need lookup flag after the dentry is setup
BTRFS: Fix lseek return value for error
Btrfs: don't change inode flag of the dest clone file
Btrfs: don't make a file partly checksummed through file clone
Btrfs: fix pages truncation in btrfs_ioctl_clone()
btrfs: fix d_off in the first dirent
USB: xHCI: prevent infinite loop when processing MSE event
When a xHC host is unable to handle isochronous transfer in the
interval, it reports a Missed Service Error event and skips some tds.
Currently xhci driver handles MSE event in the following ways:
1. When encounter a MSE event, set ep->skip flag, update event ring
dequeue pointer and return.
2. When encounter the next event on this ep, the driver will run the
do-while loop, fetch td from ep's td_list to find the td
corresponding to this event. All tds missed are marked as short
transfer(-EXDEV).
The do-while loop will end in two ways:
1. If the td pointed by the event trb is found;
2. If the ep ring's td_list is empty.
However, if a buggy HW reports some unpredicted event (for example, an
overrun event following a MSE event while the ep ring is actually not
empty), the driver will never find the td, and it will loop until the
td_list is empty.
Unfortunately, the spinlock is dropped when give back a urb in the
do-while loop. During the spinlock released period, the class driver
may still submit urbs and add tds to the td_list. This may cause
disaster, since the td_list will never be empty and the loop never ends,
and the system hangs.
To fix this, count the number of TDs on the ep ring before skipping TDs,
and quit the loop when skipped that number of tds. This guarantees the
do-while loop will end after certain number of cycles, and driver will
not be trapped in an infinite loop.
USB: xhci: Set change bit when warm reset change is set.
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther
Point xHCI host controller will report a link state change with the
state set to "SS.Inactive". This causes the xHCI host controller to
issue a warm port reset, which doesn't finish before the USB core times
out while waiting for it to complete.
When the warm port reset does complete, and the xHC gives back a port
status change event, the xHCI driver kicks khubd. However, it fails to
set the bit indicating there is a change event for that port because the
logic in xhci-hub.c doesn't check for the warm port reset bit.
After that, the warm port status change bit is never cleared by the USB
core, and the xHC stops reporting port status change bits. (The xHCI
spec says it shouldn't report more port events until all change bits are
cleared.) This means any port changes when a new device is connected
will never be reported, and the port will seem "dead" until the xHCI
driver is unloaded and reloaded, or the computer is rebooted. Fix this
by making the xHCI driver set the port change bit when a warm port reset
change bit is set.
A better solution would be to make the USB core handle warm port reset
in differently, merging the current code with the standard port reset
code that does an incremental backoff on the timeout, and tries to
complete the port reset two more times before giving up. That more
complicated fix will be merged next window, and this fix will be
backported to stable.
This should be backported to kernels as old as 3.0, since that was the
first kernel with commit a11496ebf375 ("xHCI: warm reset support").
Randy Dunlap [Mon, 19 Sep 2011 23:05:10 +0000 (16:05 -0700)]
staging: fix comedi build when ISA_DMA_API is enabled but COMEDI_PCI is not enabled
Fix build when CONFIG_ISA_DMA_API is enabled but
CONFIG_COMEDI_PCI[_DRIVERS] is not enabled.
Fixes these build errors:
drivers/staging/comedi/drivers/ni_labpc.c: In function 'labpc_ai_cmd':
drivers/staging/comedi/drivers/ni_labpc.c:1351: error: implicit declaration of function 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c: At top level:
drivers/staging/comedi/drivers/ni_labpc.c:1802: error: conflicting types for 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c:1351: note: previous implicit declaration of 'labpc_suggest_transfer_size' was here
Make taskstats round statistics down to nearest 1k bytes/events
Even with just the interface limited to admin, there really is little to
reason to give byte-per-byte counts for taskstats. So round it down to
something less intrusive.
Ok, this isn't optimal, since it means that 'iotop' needs admin
capabilities, and we may have to work on this some more. But at the
same time it is very much not acceptable to let anybody just read
anybody elses IO statistics quite at this level.
Use of the GENL_ADMIN_PERM suggested by Johannes Berg as an alternative
to checking the capabilities by hand.
In ad-hoc mode, driver b43 does not issue beacons.
Signed-off-by: Manual Munz <freifunk@somakoma.de> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2)
drm/radeon/kms: fix typo in r100_blit_copy
drm/radeon: Unreference GEM object outside of spinlock in page flip error path.
drm/radeon: Don't read from CP ring write pointer registers.
drm/ttm: request zeroed system memory pages for new TT buffer objects