Mark Brown [Wed, 2 May 2012 09:38:51 +0000 (10:38 +0100)]
extcon: Add EXTCON_MECHANICAL cable type for physical presence
Some accessory detection mechanisms are able to detect that something is
physically present in the socket separately to identifying what is present
in the socket. This information can be useful to applications, for example
allowing them to indicate that a potentially broken accessory is present,
so provide a standard way to report it to userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
memory: emif: Add Kconfig dependency for TI EMIF controller
Make TI_EMIF depends on ARCH_OMAP2PLUS to avoid build breaks on other
architectures. In future if other TI non OMAP socs start using it, the
dependency can be extended.
Fix the section mismatch be renaming the struct platform_driver
variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: MyungJoo Ham <myungjoo.ham@samsung.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aneesh V [Fri, 27 Apr 2012 12:24:08 +0000 (17:54 +0530)]
memory: emif: add one-time settings
Add settings that are not dependent on frequency
or any other transient parameters. This includes
- power managment control init
- impedence calibration control
- frequency independent phy configuration registers
- initialization of temperature polling
Signed-off-by: Aneesh V <aneesh@ti.com> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc] Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aneesh V [Fri, 27 Apr 2012 12:24:07 +0000 (17:54 +0530)]
memory: emif: add interrupt and temperature handling
Add an ISR for EMIF that:
1. reports details of access errors
2. takes action on thermal events
Also clear all interrupts on shut-down. Pending IRQs
may casue problems during warm-reset.
Temperature handling:
EMIF can be configured to poll the temperature level
of an LPDDR2 device from the MR4 mode register in the
device. EMIF generates an interrupt whenever it identifies
a temperature level change between two consecutive pollings.
Some of the timing parameters need to be de-rated at high
temperatures. The interrupt handler takes care of doing
this and also takes care of going back to nominal settings
when temperature falls back to nominal levels.
Signed-off-by: Aneesh V <aneesh@ti.com> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc] Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aneesh V [Fri, 27 Apr 2012 12:24:06 +0000 (17:54 +0530)]
memory: emif: handle frequency and voltage change events
Change SDRAM timings and other settings as necessary
on voltage and frequency changes. We calculate these
register settings based on data from the device data
sheet and inputs such a frequency, voltage state(stable
or ramping), temperature level etc.
TODO: frequency and voltage change handling needs to
be integrated with clock framework and regulator
framework respectively. This is not done today
due to missing pieces in the kernel.
Signed-off-by: Aneesh V <aneesh@ti.com> Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc] Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Cromie [Fri, 27 Apr 2012 20:30:42 +0000 (14:30 -0600)]
dynamic_debug: init with early_initcall, not arch_initcall
1- Call dynamic_debug_init() from early_initcall, not arch_initcall.
2- Call dynamic_debug_init_debugfs() from fs_initcall, not module_init.
RFC: This works for me on a 64 bit desktop and a i586 SBC, but is
untested on other arches. I presume there is or was a reason
original code used arch_initcall, maybe the constraints have changed.
This makes facility available as soon as possible.
2nd change has a downside when dynamic_debug.verbose=1; all the
vpr_info()s called in the proc-fs code are activated, causing
voluminous output from dmesg. TBD: Im unsure of this explanation, but
the output is there. This could be fixed by changing those callsites
to v2pr_info(if verbose > 1).
1st change is still not early enough to enable pr_debugs in
kernel/params, so parsing of boot-args isnt logged. The reparse of
those args is however visible after params.dyndbg="+p" is processed.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- add section: Debug Messages at Module Initialization Time
- update flags indicators in example outputs to include '='
- make flags descriptions tabular
- add item on '_' flag-char
- add dyndbg, boot-args examples
- rewrap some paragraphs with long lines
In Kconfig.debug, note that compiling with -DDEBUG enables all
pr_debug()s in that code.
In kernel-parameters.txt, add dyndbg and module.dyndbg items,
and deprecate ddebug_query.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Cromie [Fri, 27 Apr 2012 20:30:40 +0000 (14:30 -0600)]
dynamic_debug: add modname arg to exec_query callchain
Pass module name into ddebug_exec_queries(), ddebug_exec_query(), and
ddebug_parse_query() as separate parameter. In ddebug_parse_query(),
the module name is added into the query struct before the query-string
is parsed. This allows the query-string to be shorter:
instead of:
$modname.dyndbg="module $modname +fp"
do this:
$modname.dyndbg="+fp"
Omitting "module $modname" from the query string is actually required
for $modname.dyndbg rules; the set-only-once check added in a previous
patch will throw an error if its added again. ddebug_query="..." has
no $modname associated with it, so the query string may include it.
This also fixes redundant "module $modname" otherwise needed to handle
multiple queries per string:
$modname.dyndbg="func foo +fp; func bar +fp"
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Cromie [Fri, 27 Apr 2012 20:30:39 +0000 (14:30 -0600)]
dynamic_debug: print ram usage by ddebug tables if verbose
Print ram usage of dynamic-debug tables and verbose section so user
knows cost of enabling CONFIG_DYNAMIC_DEBUG. This only counts the
size of the _ddebug tables for builtins and the __verbose section that
they refer to, not those used in loadable modules.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We dont want errors while parsing ddebug_query to unload ddebug
tables, so set success after tables are loaded, and return 0 after
query parsing is done.
Simplify error handling code since its no longer used for success,
and change goto label to out_err to clarify this.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Cromie [Fri, 27 Apr 2012 20:30:37 +0000 (14:30 -0600)]
dynamic_debug: combine parse_args callbacks together
Refactor ddebug_dyndbg_boot_param_cb and ddebug_dyndbg_module_param_cb
into a common helper function, and call it from both. The handling of
foo.dyndbg is unneeded by the latter, but harmless.
The 2 callers differ only by pr_info and the return code they pass to
the helper for when an unknown param is handled. I could slightly
reduce dmesg clutter by putting the vpr_info in the common helper,
after the return on_err, but that loses __func__ context, is overly
silent on module_cb unknown param errors, and the clutter is only when
dynamic_debug.verbose=1 anyway.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ddebug_dyndbg_boot_params_cb() handling bare dyndbg params, we
dont need ddebug_query param anymore. Add a warning when processing
ddebug_query= param that it is deprecated, and to change it to dyndbg=
Add a deprecation notice for v3.8 to feature-removal-schedule.txt, and
add a suggested deprecation period of 3 releases to the header.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Cromie [Fri, 27 Apr 2012 20:30:35 +0000 (14:30 -0600)]
dynamic_debug: make dynamic-debug work for module initialization
This introduces a fake module param $module.dyndbg. Its based upon
Thomas Renninger's $module.ddebug boot-time debugging patch from
https://lkml.org/lkml/2010/9/15/397
The 'fake' module parameter is provided for all modules, whether or
not they need it. It is not explicitly added to each module, but is
implemented in callbacks invoked from parse_args.
For builtin modules, dynamic_debug_init() now directly calls
parse_args(..., &ddebug_dyndbg_boot_params_cb), to process the params
undeclared in the modules, just after the ddebug tables are processed.
While its slightly weird to reprocess the boot params, parse_args() is
already called repeatedly by do_initcall_levels(). More importantly,
the dyndbg queries (given in ddebug_query or dyndbg params) cannot be
activated until after the ddebug tables are ready, and reusing
parse_args is cleaner than doing an ad-hoc parse. This reparse would
break options like inc_verbosity, but they probably should be params,
like verbosity=3.
ddebug_dyndbg_boot_params_cb() handles both bare dyndbg (aka:
ddebug_query) and module-prefixed dyndbg params, and ignores all other
parameters. For example, the following will enable pr_debug()s in 4
builtin modules, in the order given:
For loadable modules, parse_args() in load_module() calls
ddebug_dyndbg_module_params_cb(). This handles bare dyndbg params as
passed from modprobe, and errors on other unknown params.
Note that modprobe reads /proc/cmdline, so "modprobe foo" grabs all
foo.params, strips the "foo.", and passes these to the kernel.
ddebug_dyndbg_module_params_cb() is again called for the unknown
params; it handles dyndbg, and errors on others. The "doing" arg
added previously contains the module name.
For non CONFIG_DYNAMIC_DEBUG builds, the stub function accepts
and ignores $module.dyndbg params, other unknowns get -ENOENT.
If no param value is given (as in pci.dyndbg example above), "+p" is
assumed, which enables all pr_debug callsites in the module.
The dyndbg fake parameter is not shown in /sys/module/*/parameters,
thus it does not use any resources. Changes to it are made via the
control file.
Also change pr_info in ddebug_exec_queries to vpr_info,
no need to see it all the time.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> CC: Thomas Renninger <trenn@suse.de> CC: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jim Cromie [Fri, 27 Apr 2012 20:30:34 +0000 (14:30 -0600)]
params: add 3rd arg to option handler callback signature
Add a 3rd arg, named "doing", to unknown-options callbacks invoked
from parse_args(). The arg is passed as:
"Booting kernel" from start_kernel(),
initcall_level_names[i] from do_initcall_level(),
mod->name from load_module(), via parse_args(), parse_one()
parse_args() already has the "name" parameter, which is renamed to
"doing" to better reflect current uses 1,2 above. parse_args() passes
it to an altered parse_one(), which now passes it down into the
unknown option handler callbacks.
The mod->name will be needed to handle dyndbg for loadable modules,
since params passed by modprobe are not qualified (they do not have a
"$modname." prefix), and by the time the unknown-param callback is
called, the module name is not otherwise available.
Minor tweaks:
Add param-name to parse_one's pr_debug(), current message doesnt
identify the param being handled, add it.
Add a pr_info to print current level and level_name of the initcall,
and number of registered initcalls at that level. This adds 7 lines
to dmesg output, like:
initlevel:6=device, 172 registered initcalls
Drop "parameters" from initcall_level_names[], its unhelpful in the
pr_info() added above. This array is passed into parse_args() by
do_initcall_level().
CC: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Acked-by: Jason Baron <jbaron@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extcon: Notify changed state for only one cable to notifee
This patch inform the state of only one cable instead of previous data
including the state of 32 cables to notifee which use
extcon_register_interest()
function to monitor whether the specific cable is attachd or detached.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
"Fix for an issue causing hibernation to hang on systems with highmem
(that practically means i386) due to broken memory management (bug
introduced in 3.2, so -stable material) and PM documentation update
making the freezer documentation follow the code again after some
recent updates."
* tag 'pm-for-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Freezer / Docs: Update documentation about freezing of tasks
PM / Hibernate: fix the number of pages used for hibernate/thaw buffering
autofs: make the autofsv5 packet file descriptor use a packetized pipe
The autofs packet size has had a very unfortunate size problem on x86:
because the alignment of 'u64' differs in 32-bit and 64-bit modes, and
because the packet data was not 8-byte aligned, the size of the autofsv5
packet structure differed between 32-bit and 64-bit modes despite
looking otherwise identical (300 vs 304 bytes respectively).
We first fixed that up by making the 64-bit compat mode know about this
problem in commit a32744d4abae ("autofs: work around unhappy compat
problem on x86-64"), and that made a 32-bit 'systemd' work happily on a
64-bit kernel because everything then worked the same way as on a 32-bit
kernel.
But it turned out that 'automount' had actually known and worked around
this problem in user space, so fixing the kernel to do the proper 32-bit
compatibility handling actually *broke* 32-bit automount on a 64-bit
kernel, because it knew that the packet sizes were wrong and expected
those incorrect sizes.
As a result, we ended up reverting that compatibility mode fix, and
thus breaking systemd again, in commit fcbf94b9dedd.
With both automount and systemd doing a single read() system call, and
verifying that they get *exactly* the size they expect but using
different sizes, it seemed that fixing one of them inevitably seemed to
break the other. At one point, a patch I seriously considered applying
from Michael Tokarev did a "strcmp()" to see if it was automount that
was doing the operation. Ugly, ugly.
However, a prettier solution exists now thanks to the packetized pipe
mode. By marking the communication pipe as being packetized (by simply
setting the O_DIRECT flag), we can always just write the bigger packet
size, and if user-space does a smaller read, it will just get that
partial end result and the extra alignment padding will simply be thrown
away.
This makes both automount and systemd happy, since they now get the size
they asked for, and the kernel side of autofs simply no longer needs to
care - it could pad out the packet arbitrarily.
Of course, if there is some *other* user of autofs (please, please,
please tell me it ain't so - and we haven't heard of any) that tries to
read the packets with multiple writes, that other user will now be
broken - the whole point of the packetized mode is that one system call
gets exactly one packet, and you cannot read a packet in pieces.
Tested-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: David Miller <davem@davemloft.net> Cc: Ian Kent <raven@themaw.net> Cc: Thomas Meyer <thomas@m3y3r.de> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PM / Freezer / Docs: Update documentation about freezing of tasks
The file Documentation/power/freezing-of-tasks.txt was still referencing
the TIF_FREEZE flag, that was removed by the commit d88e4cb67197d007fb778d62fe17360e970d5bfa(freezer: remove now unused
TIF_FREEZE).
This patch removes all the references of TIF_FREEZE that were left
behind.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com> Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The actual internal pipe implementation is already really about
individual packets (called "pipe buffers"), and this simply exposes that
as a special packetized mode.
When we are in the packetized mode (marked by O_DIRECT as suggested by
Alan Cox), a write() on a pipe will not merge the new data with previous
writes, so each write will get a pipe buffer of its own. The pipe
buffer is then marked with the PIPE_BUF_FLAG_PACKET flag, which in turn
will tell the reader side to break the read at that boundary (and throw
away any partial packet contents that do not fit in the read buffer).
End result: as long as you do writes less than PIPE_BUF in size (so that
the pipe doesn't have to split them up), you can now treat the pipe as a
packet interface, where each read() system call will read one packet at
a time. You can just use a sufficiently big read buffer (PIPE_BUF is
sufficient, since bigger than that doesn't guarantee atomicity anyway),
and the return value of the read() will naturally give you the size of
the packet.
NOTE! We do not support zero-sized packets, and zero-sized reads and
writes to a pipe continue to be no-ops. Also note that big packets will
currently be split at write time, but that the size at which that
happens is not really specified (except that it's bigger than PIPE_BUF).
Currently that limit is the system page size, but we might want to
explicitly support bigger packets some day.
The main user for this is going to be the autofs packet interface,
allowing us to stop having to care so deeply about exact packet sizes
(which have had bugs with 32/64-bit compatibility modes). But user
space can create packetized pipes with "pipe2(fd, O_DIRECT)", which will
fail with an EINVAL on kernels that do not support this interface.
Tested-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: David Miller <davem@davemloft.net> Cc: Ian Kent <raven@themaw.net> Cc: Thomas Meyer <thomas@m3y3r.de> Cc: stable@kernel.org # needed for systemd/autofs interaction fix Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'staging-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are some tiny drivers/staging/ bugfixes. Some build fixes that
were recently reported, as well as one kfree bug that is hitting a
number of users."
* tag 'staging-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: ozwpan: Fix bug where kfree is called twice.
staging: octeon-ethernet: fix build errors by including interrupt.h
staging: zcache: fix Kconfig crypto dependency
staging: tidspbridge: remove usage of OMAP2_L4_IO_ADDRESS
Merge tag 'usb-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of small USB fixes for 3.4-rc5.
Nothing major, as before, some USB gadget fixes. There's a crash fix
for a number of ASUS laptops on resume that had been reported by a
number of different people. We think the fix might also pertain to
other machines, as this was a BIOS bug, and they seem to travel to
different models and manufacturers quite easily. Other than that,
some other reported problems fixed as well."
* tag 'usb-3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: udc-core: fix incompatibility with dummy-hcd
usb: gadget: udc-core: fix wrong call order
USB: cdc-wdm: fix race leading leading to memory corruption
USB: EHCI: fix crash during suspend on ASUS computers
usb gadget: uvc: uvc_request_data::length field must be signed
usb: gadget: dummy: do not call pullup() on udc_stop()
usb: musb: davinci.c: add missing unregister
usb: musb: drop __deprecated flag
USB: gadget: storage gadgets send wrong error code for unknown commands
usb: otg: gpio_vbus: Add otg transceiver events and notifiers
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This has our collection of bug fixes. I missed the last rc because I
thought our patches were making NFS crash during my xfs test runs.
Turns out it was an NFS client bug fixed by someone else while I tried
to bisect it.
All of these fixes are small, but some are fairly high impact. The
biggest are fixes for our mount -o remount handling, a deadlock due to
GFP_KERNEL allocations in readdir, and a RAID10 error handling bug.
This was tested against both 3.3 and Linus' master as of this morning."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (26 commits)
Btrfs: reduce lock contention during extent insertion
Btrfs: avoid deadlocks from GFP_KERNEL allocations during btrfs_real_readdir
Btrfs: Fix space checking during fs resize
Btrfs: fix block_rsv and space_info lock ordering
Btrfs: Prevent root_list corruption
Btrfs: fix repair code for RAID10
Btrfs: do not start delalloc inodes during sync
Btrfs: fix that check_int_data mount option was ignored
Btrfs: don't count CRC or header errors twice while scrubbing
Btrfs: fix btrfs_ioctl_dev_info() crash on missing device
btrfs: don't return EINTR
Btrfs: double unlock bug in error handling
Btrfs: always store the mirror we read the eb from
fs/btrfs/volumes.c: add missing free_fs_devices
btrfs: fix early abort in 'remount'
Btrfs: fix max chunk size check in chunk allocator
Btrfs: add missing read locks in backref.c
Btrfs: don't call free_extent_buffer twice in iterate_irefs
Btrfs: Make free_ipath() deal gracefully with NULL pointers
Btrfs: avoid possible use-after-free in clear_extent_bit()
...
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Nothing controversial, just another batch of fixes:
- Samsung/exynos fixes for more merge window fallout: build errors
and warnings mostly, but also some clock/device setup issues on
exynos4/5
- PXA bug and warning fixes related to gpio and pinmux
- IRQ domain conversion bugfixes for U300 and MSM
- A regulator setup fix for U300"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PXA2xx: MFP: fix potential direction bug
ARM: PXA2xx: MFP: fix bug with MFP_LPM_KEEP_OUTPUT
arm/sa1100: fix sa1100-rtc memory resource
ARM: pxa: fix gpio wakeup setting
ARM: SAMSUNG: add missing MMC_CAP2_BROKEN_VOLTAGE capability
ARM: EXYNOS: Fix compilation error when CONFIG_OF is not defined
ARM: EXYNOS: Fix resource on dev-dwmci.c
ARM: S3C24XX: Fix build warning for S3C2410_PM
ARM: mini2440_defconfig: Fix build error
ARM: msm: Fix gic irqdomain support
ARM: EXYNOS: Fix incorrect initialization of GIC
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
ARM: u300: bump all IRQ numbers by one
ARM: ux300: Fix unimplementable regulation constraints
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"As soon as I sent the non-urgent stack, two important fixes come in:
- i915: fixes SNB GPU hangs in a number of 3D apps
- radeon: initial fix for VGA on LLano system, 3 or 4 of us have
spent time debugging this, and Jerome finally figured out the magic
bit the BIOS/fglrx set that we didn't. This at least should get
things working, there may be future reliability fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Set the Stencil Cache eviction policy to non-LRA mode.
drm/radeon/kms: need to set up ss on DP bridges as well
While that commit was technically the right thing to do, and made the
x86-64 compat mode work identically to native 32-bit mode (and thus
fixing the problem with a 32-bit systemd install on a 64-bit kernel), it
turns out that the automount binaries had workarounds for this compat
problem.
Now, the workarounds are disgusting: doing an "uname()" to find out the
architecture of the kernel, and then comparing it for the 64-bit cases
and fixing up the size of the read() in automount for those. And they
were confused: it's not actually a generic 64-bit issue at all, it's
very much tied to just x86-64, which has different alignment for an
'u64' in 64-bit mode than in 32-bit mode.
But the end result is that fixing the compat layer actually breaks the
case of a 32-bit automount on a x86-64 kernel.
There are various approaches to fix this (including just doing a
"strcmp()" on current->comm and comparing it to "automount"), but I
think that I will do the one that teaches pipes about a special "packet
mode", which will allow user space to not have to care too deeply about
the padding at the end of the autofs packet.
That change will make the compat workaround unnecessary, so let's revert
it first, and get automount working again in compat mode. The
packetized pipes will then fix autofs for systemd.
Reported-and-requested-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Ian Kent <raven@themaw.net> Cc: stable@kernel.org # for 3.3 Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drm/i915: Set the Stencil Cache eviction policy to non-LRA mode.
Clearing bit 5 of CACHE_MODE_0 is necessary to prevent GPU hangs in
OpenGL programs such as Google MapsGL, Google Earth, and gzdoom when
using separate stencil buffers. Without it, the GPU tries to use the
LRA eviction policy, which isn't supported. This was supposed to be off
by default, but seems to be on for many machines.
This cannot be done in gen6_init_clock_gating with most of the other
workaround bits; the render ring needs to exist. Otherwise, the
register write gets dropped on the floor (one printk will show it
changed, but a second printk immediately following shows the value
reverts to the old one).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47535 Cc: stable@vger.kernel.org Cc: Rob Castle <futuredub@gmail.com> Cc: Eric Appleman <erappleman@gmail.com> Cc: aaron667@gmx.net Cc: Keith Packard <keithp@keithp.com> Signed-off-by: Kenneth Graunke <kenneth@whitecape.org> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.samba.org/sfrench/cifs-2.6:
Use correct conversion specifiers in cifs_show_options
CIFS: Show backupuid/gid in /proc/mounts
cifs: fix offset handling in cifs_iovec_write
Merge tag 'stable/for-linus-3.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Some of these had been in existence since the 2.6.27 days, some since
3.0 - and some due to new features added in v3.4.
The one that is most interesting is David's one - in the low-level
assembler code we had be checking events needlessly. With his patch
now we do it when the appropriate flag is set - with the added benefit
that we can process events faster. Stefano's is fixing a mistake
where the Linux IRQ numbers were ACK-ed instead of the Xen IRQ,
resulting in missing interrupts. The other ones are bootup related
that can show up on various hardware."
- In the low-level assembler code we would jump to check events even if
none were present. This incorrect behavior had been there since
2.6.27 days!
- When using the fast-path for ACK-ing interrupts we were using the
Linux IRQ numbers instead of the Xen ones (and they can differ) and
missing interrupts in process.
- Fix bootup crashes when ACPI hotplug CPUs were present and they would
expand past the set number of CPUs we were allocated.
- Deal with broken BIOSes when uploading C-states to the hypervisor.
- Disable the cpuid check for MWAIT_LEAF if the ACPI PAD driver is
loaded. If the ACPI PAD driver is used it will crash, so lets not
export the functionality so the ACPI PAD driver won't load.
* tag 'stable/for-linus-3.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: correctly check for pending events when restoring irq flags
xen/acpi: Workaround broken BIOSes exporting non-existing C-states.
xen/smp: Fix crash when booting with ACPI hotplug CPUs.
xen: use the pirq number to check the pirq_eoi_map
xen/enlighten: Disable MWAIT_LEAF so that acpi-pad won't be loaded.
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull misc SPI device driver bug fixes from Grant Likely.
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/spi-bfin5xx: Fix flush of last bit after each spi transfer
spi/spi-bfin5xx: fix reversed if condition in interrupt mode
spi/spi_bfin_sport: drop bits_per_word from client data
spi/bfin_spi: drop bits_per_word from client data
spi/spi-bfin-sport: move word length setup to transfer handler
spi/bfin5xx: rename config macro name for bfin5xx spi controller driver
spi/pl022: Allow request for higher frequency than maximum possible
spi/bcm63xx: set master driver mode_bits.
spi/bcm63xx: don't use the stopping state
spi/bcm63xx: convert to the pump message infrastructure
spi/spi-ep93xx.c: use dma_transfer_direction instead of dma_data_direction
spi: fix spi.h kernel-doc warning
spi/pl022: Fix calculate_effective_freq()
spi/pl022: Fix range checking for bits per word
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"For your Friday pull request stack, nothing astounding or shattering
this week some exynos, some intel, some radeon fixes. One intel fix
for a regression somwehere back in 2.6.35 land."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: use frac fb div on APUs
drm/radeon: add a missing entry to encoder_names
drm/i915: handle input/output sdvo timings separately in mode_set
drm/i915: fix integer overflow in i915_gem_do_execbuffer()
drm/i915: fix integer overflow in i915_gem_execbuffer2()
drm/exynos: added missed vm area region mapping type.
drm/exynos: fixed exynos_drm_gem_map_pages bug.
drm/exynos: fixed duplicatd memory allocation bug.
drm/i915: fixup load-detect on enabled, but not active pipe
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Use x2apic physical mode based on FADT setting
x86/mrst: Quiet sparse noise about plain integer as NULL pointer
x86, intel_cacheinfo: Fix error return code in amd_set_l3_disable_slot()
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix perf_event_for_each() to use sibling
perf symbols: Read plt symbols from proper symtab_type binary
tracing: Fix stacktrace of latency tracers (irqsoff and friends)
perf tools: Add 'G' and 'H' modifiers to event parsing
tracing: Fix regression with tracing_on
perf tools: Drop CROSS_COMPILE from flex and bison calls
perf report: Fix crash showing warning related to kernel maps
tracing: Fix build breakage without CONFIG_PERF_EVENTS (again)
Merge branch 'for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull build fixes for less mainstream architectures from Paul Gortmaker:
"These are fixes for frv(1), blackfin(2), powerpc(1) and xtensa(4).
Fortunately the touches are nearly all specific to files just used by
the arch in question. The two touches to shared/common files
[kernel/irq/debug.h and drivers/pci/Makefile] are trivial to assess as
no risk to anyone.
Half of them relate to xtensa directly. It was only when I fixed the
last xtensa issue that I realized that the arch has been broken for a
significant time, and isn't a specific v3.4 regression. So if you
wanted, we could leave xtensa lying bleeding in the street for a
couple more weeks and queue those for 3.5. But given they are no risk
to anyone outside of xtensa, I figured to just leave them in.
If you are OK with taking the xtensa fixes, then please pull to get:
- one last implicit include uncovered by system.h that is in a file
specific to just one powerpc defconfig. (I'd sync'd with BenH).
- fix an oversight in the PCI makefile where shared code wasn't being
compiled for ARCH=frv
- fix a missing include for GPIO in blackfin framebuffer.
- audit and tag endif in blackfin ezkit board file, in order to find
and fix the misplaced endif masking a block of code.
- fix irq/debug.h choice of temporary macro names to be more internal
so they don't conflict with names used by xtensa.
- fix a reference to an undeclared local var in xtensa's signal.c
- fix an implicit bug.h usage in xtensa's asm/io.h uncovered by my
removing bug.h from kernel.h
- fix xtensa to properly indicate it is using asm-generic/hardirq.h
in order to resolve the link error - undefined ack_bad_irq
The xtensa still fails final link as my latest binutils does something
evil when ld forward-relocates unlikely() blocks, but in theory people
who have older/valid toolchains could now use the thing."
* 'for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
xtensa: fix build fail on undefined ack_bad_irq
blackfin: fix ifdef fustercluck in mach-bf538/boards/ezkit.c
blackfin: fix compile error in bfin-lq035q1-fb.c
pci: frv architecture needs generic setup-bus infrastructure
irq: hide debug macros so they don't collide with others.
xtensa: fix build error in xtensa/include/asm/io.h
xtensa: fix build failure in xtensa/kernel/signal.c
powerpc: fix system.h fallout in sysdev/scom.c [chroma_defconfig]
Merge branch 'docs-3.4' of git://git.samba.org/jlayton/linux
Pull security key doc update from Jeff Layton:
"Ordinarily, I send my patches through others' trees, but David
suggested I just send this one to you directly since it's just a
Documentation/ update"
* 'docs-3.4' of git://git.samba.org/jlayton/linux:
keys: update the documentation with info about "logon" keys
David Vrabel [Thu, 26 Apr 2012 18:44:06 +0000 (19:44 +0100)]
xen: correctly check for pending events when restoring irq flags
In xen_restore_fl_direct(), xen_force_evtchn_callback() was being
called even if no events were pending. This resulted in (depending on
workload) about a 100 times as many xen_version hypercalls as
necessary.
Fix this by correcting the sense of the conditional jump.
This seems to give a significant performance benefit for some
workloads.
There is some subtle tricksy "..since the check here is trying to
check both pending and masked in a single cmpw, but I think this is
correct. It will call check_events now only when the combined
mask+pending word is 0x0001 (aka unmasked, pending)." (Ian)
CC: stable@kernel.org Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Chris Mason [Fri, 27 Apr 2012 18:31:29 +0000 (14:31 -0400)]
Btrfs: reduce lock contention during extent insertion
We're spending huge amounts of time on lock contention during
end_io processing because we unconditionally assume we are overwriting
an existing extent in the file for each IO.
This checks to see if we are outside i_size, and if so, it uses a
less expensive readonly search of the btree to look for existing
extents.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Scott Jiang [Mon, 23 Apr 2012 22:18:11 +0000 (18:18 -0400)]
spi/spi_bfin_sport: drop bits_per_word from client data
Since the member was dropped from the common Blackfin header, we need
to stop using it in the SPORT driver too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Scott Jiang [Mon, 23 Apr 2012 22:18:10 +0000 (18:18 -0400)]
spi/bfin_spi: drop bits_per_word from client data
No other SPI controller has this field, and SPI clients should be setting
this up in their own drivers. So drop it from the Blackfin controller to
keep people from using it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi/pl022: Allow request for higher frequency than maximum possible
Currently, if we request for frequency greater than maximum possible, spi driver
returns error.
For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...
It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...
For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.
Stefan Behrens [Fri, 27 Apr 2012 16:41:46 +0000 (12:41 -0400)]
Btrfs: fix block_rsv and space_info lock ordering
may_commit_transaction() calls
spin_lock(&space_info->lock);
spin_lock(&delayed_rsv->lock);
and update_global_block_rsv() calls
spin_lock(&block_rsv->lock);
spin_lock(&sinfo->lock);
Lockdep complains about this at run time.
Everywhere except in update_global_block_rsv(), the space_info lock is
the outer lock, therefore the locking order in update_global_block_rsv()
is changed.
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Jan Schmidt [Fri, 27 Apr 2012 16:41:45 +0000 (12:41 -0400)]
Btrfs: fix repair code for RAID10
btrfs_map_block sets mirror_num, so that the repair code knows eventually
which device gave us the read error. For RAID10, mirror_num must be 1 or 2.
Before this fix mirror_num was incorrectly related to our stripe index.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Tue, 24 Apr 2012 00:35:03 +0000 (20:35 -0400)]
Btrfs: do not start delalloc inodes during sync
btrfs_start_delalloc_inodes will just walk the list of delalloc inodes and
start writing them out, but it doesn't splice the list or anything so as
long as somebody is doing work on the box you could end up in this section
_forever_. So just remove it, it's not needed anyway since sync will start
writeback on all inodes anyway, all we need to do is wait for ordered
extents and then we can commit the transaction. In my horrible torture test
sync goes from taking 4 minutes to about 1.5 minutes. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
We do not need to use a flag to indicate if the master driver is stopping
it is sufficient to perform spi master unregistering in the platform
driver's remove function.
Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi/bcm63xx: convert to the pump message infrastructure
This patch converts the bcm63xx SPI driver to use the SPI infrastructure
pump message queue. Since we were previously sleeping in the SPI
driver's transfer() function (which is not allowed) this is now fixed as well.
To complete that conversion a certain number of changes have been made:
- the transfer len is split into multiple hardware transfers in case its
size is bigger than the hardware FIFO size
- the FIFO refill is no longer done in the interrupt context, which was a
bad idea leading to quick interrupt handler re-entrancy
warning: mixing different enum types
int enum dma_data_direction versus
int enum dma_transfer_direction
This is produced because the 'dir' passed in ep93xx_spi_dma_prepare
is an enum dma_data_direction and is being used to set the
dma_slave_config 'direction' which is now an enum dma_transfer_direction.
Fix this by converting spi-ep93xx to use the new enum type in all
places.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Mika Westerberg <mika.westerberg@iki.fi> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Olof Johansson [Fri, 27 Apr 2012 16:40:06 +0000 (09:40 -0700)]
Merge branch 'v3.4-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.4-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: add missing MMC_CAP2_BROKEN_VOLTAGE capability
ARM: EXYNOS: Fix compilation error when CONFIG_OF is not defined
ARM: EXYNOS: Fix resource on dev-dwmci.c
ARM: S3C24XX: Fix build warning for S3C2410_PM
ARM: mini2440_defconfig: Fix build error
ARM: EXYNOS: Fix incorrect initialization of GIC
ARM: EXYNOS: use 'exynos4-sdhci' as device name for sdhci controllers
Merge tag 'fixes-for-v3.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.4-rc cycle
A few more fixes for v3.4-rc cycle.
It includes a couple of fixes to the ordering of the methods in udc-core.c.
Without these two patches, we will have issues when either unregistering a
gadget driver (triggered with dummy_hcd only) or issuing a device-initiated
disconnect through sysfs.
There's also a fix on dummy_hcd to not call ->pullup() from udc_stop() because
udc-core.c already handles that.
A fix to MUSB as promised, to kill the compile warnings regarding deprecated
interfaces. We are essentially dropping the __deprecated flag because it
doesn't look like we will ever be able to live without it when we consider the
amount of silicon issues we find on different MUSB instantiations.
A couple of other fixes are also available, one adding the missing transceiver
events to gpio_vbus and another adding a missing unregister call to MUSB's
davinci glue layer.
Alan Stern [Thu, 26 Apr 2012 15:31:57 +0000 (11:31 -0400)]
usb: gadget: udc-core: fix incompatibility with dummy-hcd
This patch (as1548) fixes a recently-introduced incompatibility
between the UDC core and the dummy-hcd driver. Commit 8ae8090c82eb407267001f75b3d256b3bd4ae691 (usb: gadget: udc-core: fix
asymmetric calls in remove_driver) moved the usb_gadget_udc_stop()
call in usb_gadget_remove_driver() below the usb_gadget_disconnect()
call.
As a result, usb_gadget_disconnect() gets called at a time when the
gadget driver believes it has been unbound but dummy-hcd believes
it has not. A nasty error ensues when dummy-hcd calls the gadget
driver's disconnect method a second time.
To fix the problem, this patch moves the gadget driver's unbind
notification after the usb_gadget_disconnect() call. Now nothing
happens between the two unbind notifications, so nothing goes wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi [Fri, 27 Apr 2012 08:02:15 +0000 (11:02 +0300)]
usb: gadget: udc-core: fix wrong call order
commit 6d258a4 (usb: gadget: udc-core: stop UDC on device-initiated
disconnect) introduced another case of asymmetric calls when issuing
a device-initiated disconnect. Fix it.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Felipe Balbi <balbi@ti.com>
Dave Airlie [Fri, 27 Apr 2012 07:21:28 +0000 (08:21 +0100)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
From Daniel Vetter
- VGA load-detect fix. This bug seems to be as old as the load-detect code
(2.6.30), but needs stupid userspace (upowerd trying to detect
connectors on dpms-off outputs) to actually kill the machine. And
obviously a machine without VGA-hotplug, otherwise we don't do load
detect.
- 2 interger overflow fixes for unpriviledged ioctls from Xi Wang.
- Fix SDVO regression for low-res (pixelclock < 100MHz) digital outputs,
introduce in 2.6.36.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: handle input/output sdvo timings separately in mode_set
drm/i915: fix integer overflow in i915_gem_do_execbuffer()
drm/i915: fix integer overflow in i915_gem_execbuffer2()
drm/i915: fixup load-detect on enabled, but not active pipe
Igor Grinberg [Thu, 12 Apr 2012 12:43:29 +0000 (15:43 +0300)]
ARM: PXA2xx: MFP: fix potential direction bug
Pins configured as input and have MFP_LPM_DRIVE_* flag set, can have a
wrong output value for some period of time (spike) during the suspend
sequence.
This can happen because the direction of the pins (GPDR) is set by
software and the output level is set by hardware (PGSR) at a later
stage.
Fix the above potential bug by setting the output levels first.
Also save the actual levels of the pins before the suspend and restore
them after the resume, but before the direction settings take place, so
the same bug as described above will not happen in the resume sequence.
Reported-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Igor Grinberg [Thu, 12 Apr 2012 12:43:28 +0000 (15:43 +0300)]
ARM: PXA2xx: MFP: fix bug with MFP_LPM_KEEP_OUTPUT
Pins that have MFP_LPM_KEEP_OUTPUT set and are configured for output
must retain the output state in low power mode.
Currently, the pin direction configuration is overrided with values
in gpdr_lpm[] array and do not obey the MFP_LPM_KEEP_OUTPUT setting.
Fix the above bug and add some documentation to clarify the
MFP_LPM_KEEP_OUTPUT setting purpose.
Reported-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Paul Parsons <lost.distance@yahoo.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
DEFINE_RES_MEM() takes the size of resource as a second argument,
not the end address. Passing end address leads to following error
in runtime during device registration:
sa1100-rtc: failed to claim resource 0
Robert Jarzmik [Sun, 22 Apr 2012 11:37:24 +0000 (13:37 +0200)]
ARM: pxa: fix gpio wakeup setting
In 3.3, gpio wakeup setting was broken. The call
enable_irq_wake() didn't set up the PXA gpio registers
(PWER, ...) anymore.
Fix it at least for pxa27x. The driver doesn't seem to be
used in pxa25x (weird ...), and the fix doesn't extend to
pxa3xx and pxa95x (which don't have a gpio_set_wake()
available).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
We did a similar check for the P-states but did not do it for
the C-states. What we want to do is ignore cases where the DSDT
has definition for sixteen CPUs, but the machine only has eight
CPUs and we get:
xen-acpi-processor: (CX): Hypervisor error (-22) for ACPI CPU14
Reported-by: Tobias Geiger <tobias.geiger@vido.info> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
xen/smp: Fix crash when booting with ACPI hotplug CPUs.
When we boot on a machine that can hotplug CPUs and we
are using 'dom0_max_vcpus=X' on the Xen hypervisor line
to clip the amount of CPUs available to the initial domain,
we get this:
(XEN) Command line: com1=115200,8n1 dom0_mem=8G noreboot dom0_max_vcpus=8 sync_console mce_verbosity=verbose console=com1,vga loglvl=all guest_loglvl=all
.. snip..
DMI: Intel Corporation S2600CP/S2600CP, BIOS SE5C600.86B.99.99.x032.072520111118 07/25/2011
.. snip.
SMP: Allowing 64 CPUs, 32 hotplug CPUs
installing Xen timer for CPU 7
cpu 7 spinlock event irq 361
NMI watchdog: disabled (cpu7): hardware events not enabled
Brought up 8 CPUs
.. snip..
[acpi processor finds the CPUs are not initialized and starts calling
arch_register_cpu, which creates /sys/devices/system/cpu/cpu8/online]
CPU 8 got hotplugged
CPU 9 got hotplugged
CPU 10 got hotplugged
.. snip..
initcall 1_acpi_battery_init_async+0x0/0x1b returned 0 after 406 usecs
calling erst_init+0x0/0x2bb @ 1
[and the scheduler sticks newly started tasks on the new CPUs, but
said CPUs cannot be initialized b/c the hypervisor has limited the
amount of vCPUS to 8 - as per the dom0_max_vcpus=8 flag.
The spinlock tries to kick the other CPU, but the structure for that
is not initialized and we crash.]
BUG: unable to handle kernel paging request at fffffffffffffed8
IP: [<ffffffff81035289>] xen_spin_lock+0x29/0x60
PGD 180d067 PUD 180e067 PMD 0
Oops: 0002 [#1] SMP
CPU 7
Modules linked in:
sh: Fix up tracepoint build fallout from static key introduction.
With the introduction of static keys, anything using tracepoints blows up
in the following manner:
include/trace/events/oom.h:8:13: error: initializer element is not constant
include/trace/events/oom.h:8:13: error: (near initialization for '__tracepoint_oom_score_adj_update')
include/trace/events/oom.h:8:13: error: initializer element is not constant
include/trace/events/oom.h:8:13: error: (near initialization for '__tracepoint_oom_score_adj_update.key')
This is a result of the STATIC_KEY_INIT_xxx defs wrapping ATOMIC_INIT()
which on sh includes an atomic_t typecast. Given that we don't really
need the typecast for anything anymore, the simplest solution is simply
to kill off the cast.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Oliver Neukum [Thu, 26 Apr 2012 19:59:10 +0000 (21:59 +0200)]
USB: cdc-wdm: fix race leading leading to memory corruption
This patch fixes a race whereby a pointer to a buffer
would be overwritten while the buffer was in use leading
to a double free and a memory leak. This causes crashes.
This bug was introduced in 2.6.34
Merge branch 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile fixes from Chris Metcalf:
"One change fixes a platform-independent bug about environment var
handling in the boot command line. The other is a trivial
tile-specific bug fix to avoid a link-time warning."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: fix a couple of functions that should be __init
init: fix bug where environment vars can't be passed via boot args
Merge tag 'ib-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"A few fixes for regressions introduced in 3.4-rc1:
- fix memory leak in mlx4
- fix two problems with new MAD response generation code"
* tag 'ib-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix memory leaks in ib_link_query_port()
IB/mad: Don't send response for failed MADs
IB/mad: Set 'D' bit in response for unhandled MADs
converted over to using the asm-generic parts, but it also
added the sentinel
#define ack_bad_irq ack_bad_irq
which tells asm-generic to _not_ use the common ack_bad_irq.
Since e520c41 deleted the duplicated code from the arch specific
file, we _do_ want the asm-generic one in scope. So delete
the trigger define above which hides it. In doing so we'll
realize that we've got to delete the almost-duplicate prototype
as well to avoid "static declaration ... follows non-static".
Cc: Christoph Hellwig <hch@lst.de> Cc: Chris Zankel <chris@zankel.net> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull [GIT PULL] slave-dmaengine fixes from Vinod Koul.
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine/amba-pl08x : reset phychan_hold on terminate all
dma: pl330: fix a couple of compilation warnings
dma/ste_dma40: fix erroneous comparison
dma/ste_dma40: explicitly include regulator consumer header
dma40: Improve the logic of stopping logical chan
dmaengine: at_hdmac: remove clear-on-read in atc_dostart()
dma: mxs-dma: enable channel in device_issue_pending call
dmaengine: imx-dma: dont complete descriptor for cyclic dma
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A workaround for an ASUS laptop and a few ASoC changes; most of the
commits are tagged for stable, too."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Improve sequencing of AIF channel enables
ALSA: HDA: Add external mic quirk for Asus Zenbook UX31E
ASoC: fsi: update for dmaengine prep_slave_sg fallout.
ASoC: core: Fix card RTD count for deferred probe.
ASoC: cs42l73: don't use negative array index
ASoC: dapm: Ensure power gets managed for line widgets
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner.
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Fix the spurious broadcast timer ticks after resume
tick: Ensure that the broadcast device is initialized
tick: Fix oneshot broadcast setup really
Merge fixes from Andrew Morton:
"13 fixes. The acerhdf patches aren't (really) fixes. But they've
been stuck in my tree for up to two years, sent to Matthew multiple
times and the developers are unhappy."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (13 patches)
mm: fix NULL ptr dereference in move_pages
mm: fix NULL ptr dereference in migrate_pages
revert "proc: clear_refs: do not clear reserved pages"
drivers/rtc/rtc-ds1307.c: fix BUG shown with lock debugging enabled
arch/arm/mach-ux500/mbox-db5500.c: world-writable sysfs fifo file
hugetlbfs: lockdep annotate root inode properly
acerhdf: lowered default temp fanon/fanoff values
acerhdf: add support for new hardware
acerhdf: add support for Aspire 1410 BIOS v1.3314
fs/buffer.c: remove BUG() in possible but rare condition
mm: fix up the vmscan stat in vmstat
epoll: clear the tfile_check_list on -ELOOP
mm/hugetlb: fix warning in alloc_huge_page/dequeue_huge_page_vma
xen: use the pirq number to check the pirq_eoi_map
In pirq_check_eoi_map use the pirq number rather than the Linux irq
number to check whether an eoi is needed in the pirq_eoi_map.
The reason is that the irq number is not always identical to the
pirq number so if we wrongly use the irq number to check the
pirq_eoi_map we are going to check for the wrong pirq to EOI.
As a consequence some interrupts might not be EOI'ed by the
guest correctly.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Tested-by: Tobias Geiger <tobias.geiger@vido.info>
[v1: Added some extra wording to git commit] Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>