Bruce Allan [Tue, 8 Dec 2009 07:28:20 +0000 (07:28 +0000)]
e1000e: only perform ESB2 MDIC workaround on certain configurations
A workaround added for all ESB2 devices (adds a delay for all MDIC accesses
which resolves an issue with the MDIC ready bit being set prematurely) is
applicable only to devices in which the MAC-PHY interconnect is not
operating in a certain mode with in-band MDIO. Check the control register
for the operating mode and enable the workaround accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 8 Dec 2009 07:28:01 +0000 (07:28 +0000)]
e1000e: replace incorrect use of GG82563_REG macro
The GG82563_REG() macro should not be used to determine the offset provided
to the e1000e_[read|write]_kmrn_reg() functions since the first argument to
the macro is already implied and gets masked off anyway in the functions.
The resultant register reads/writes with this patch are functionally the
same as before.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Tue, 8 Dec 2009 07:27:41 +0000 (07:27 +0000)]
e1000e: minor correction to name of bit in CTRL_EXT register
Bit 7 in the CTRL_REG register is actually the Software Definable Pin 3,
not the Software Definable Pin 7.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 8 Dec 2009 20:51:22 +0000 (12:51 -0800)]
sctp: fix compile error due to sysctl mismerge
I messed up the merge in d7fc02c7bae7b1cf69269992cf880a43a350cdaa, where
the conflict in question wasn't just about CTL_UNNUMBERED being removed,
but the 'strategy' field is too (sysctl handling is now done through the
/proc interface, with no duplicate protocols for reading the data).
Linus Torvalds [Tue, 8 Dec 2009 16:19:16 +0000 (08:19 -0800)]
Merge branch 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
cfq-iosched: Do not access cfqq after freeing it
block: include linux/err.h to use ERR_PTR
cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
blkio: Allow CFQ group IO scheduling even when CFQ is a module
blkio: Implement dynamic io controlling policy registration
blkio: Export some symbols from blkio as its user CFQ can be a module
block: Fix io_context leak after failure of clone with CLONE_IO
block: Fix io_context leak after clone with CLONE_IO
cfq-iosched: make nonrot check logic consistent
io controller: quick fix for blk-cgroup and modular CFQ
cfq-iosched: move IO controller declerations to a header file
cfq-iosched: fix compile problem with !CONFIG_CGROUP
blkio: Documentation
blkio: Wait on sync-noidle queue even if rq_noidle = 1
blkio: Implement group_isolation tunable
blkio: Determine async workload length based on total number of queues
blkio: Wait for cfq queue to get backlogged if group is empty
blkio: Propagate cgroup weight updation to cfq groups
blkio: Drop the reference to queue once the task changes cgroup
blkio: Provide some isolation between groups
...
Linus Torvalds [Tue, 8 Dec 2009 16:18:01 +0000 (08:18 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
Linus Torvalds [Tue, 8 Dec 2009 16:13:35 +0000 (08:13 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: parport_mfc3 - Not makes it a bool before the comparison.
m68k: don't export static inline functions
fbdev: atafb - add palette register check
m68k: Remove the BKL from sys_execve
m68k: Cleanup linker scripts using new linker script macros.
m68k: Make thread_info.h usable from assembly.
m68knommu: define arch_has_single_step() and friends
m68k: ptrace fixes
m68k: use generic code for ptrace requests
rtc: Add an RTC driver for the Ricoh RP5C01
rtc: Add an RTC driver for the Oki MSM6242
Linus Torvalds [Tue, 8 Dec 2009 16:12:16 +0000 (08:12 -0800)]
Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-stub: Documentation update
i2c-stub: Allow user to disable some commands
i2c-stub: Implement I2C block support
i2c: Refactor for_each callbacks
i2c-i801: Retry on lost arbitration
i2c: Remove big kernel lock from i2cdev_open
ics932s401: Clean up detect function
i2c: Simplify i2c_detect_address
i2c: Drop probe, ignore and force module parameters
i2c: Add missing __devinit markers to old i2c adapter drivers
i2c: Bus drivers don't have to support I2C_M_REV_DIR_ADDR
i2c: Prevent priority inversion on top of bus lock
i2c-voodoo3: Delete
i2c-powermac: Drop temporary name buffer
i2c-powermac: Include the i2c_adapter in struct pmac_i2c_bus
i2c-powermac: Log errors
i2c-powermac: Refactor i2c_powermac_smbus_xfer
i2c-powermac: Reject unsupported I2C transactions
i2c/chips: Move ds1682 to drivers/misc
Linus Torvalds [Tue, 8 Dec 2009 16:07:16 +0000 (08:07 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Add flag for devices capable of generating run-time wake-up events
PM / Runtime: Remove unnecessary braces in __pm_runtime_set_status()
PM / Runtime: Make documentation of runtime_idle() agree with the code
PM / Runtime: Ensure timer_expires is nonzero in pm_schedule_suspend()
PM / Runtime: Use deferred_resume flag in pm_request_resume
PM / Runtime: Export the PM runtime workqueue
PM / Runtime: Fix lockdep warning in __pm_runtime_set_status()
PM / Hibernate: Swap, use KERN_CONT
PM / Hibernate: Shift remaining code from swsusp.c to hibernate.c
PM / Hibernate: Move swap functions to kernel/power/swap.c.
PM / freezer: Don't get over-anxious while waiting
Linus Torvalds [Tue, 8 Dec 2009 16:02:38 +0000 (08:02 -0800)]
Merge branch 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (84 commits)
KVM: VMX: Fix comparison of guest efer with stale host value
KVM: s390: Fix prefix register checking in arch/s390/kvm/sigp.c
KVM: Drop user return notifier when disabling virtualization on a cpu
KVM: VMX: Disable unrestricted guest when EPT disabled
KVM: x86 emulator: limit instructions to 15 bytes
KVM: s390: Make psw available on all exits, not just a subset
KVM: x86: Add KVM_GET/SET_VCPU_EVENTS
KVM: VMX: Report unexpected simultaneous exceptions as internal errors
KVM: Allow internal errors reported to userspace to carry extra data
KVM: Reorder IOCTLs in main kvm.h
KVM: x86: Polish exception injection via KVM_SET_GUEST_DEBUG
KVM: only clear irq_source_id if irqchip is present
KVM: x86: disallow KVM_{SET,GET}_LAPIC without allocated in-kernel lapic
KVM: x86: disallow multiple KVM_CREATE_IRQCHIP
KVM: VMX: Remove vmx->msr_offset_efer
KVM: MMU: update invlpg handler comment
KVM: VMX: move CR3/PDPTR update to vmx_set_cr3
KVM: remove duplicated task_switch check
KVM: powerpc: Fix BUILD_BUG_ON condition
KVM: VMX: Use shared msr infrastructure
...
Trivial conflicts due to new Kconfig options in arch/Kconfig and kernel/Makefile
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6:
sparc: Set UTS_MACHINE correctly.
sparc,leon: init_leon srmmu cleanup
sparc32: Remove early interrupt enable.
sparc, leon: Added Aeroflex Gaisler entry in manufacturer_info structure
sparc64: Faster early-boot framebuffer console.
Revert "sparc: Make atomic locks raw"
sparc: remove unused nfsd #includes
sparc: Fixup last users of irq_chip->typename
Added sparc_leon3_snooping_enabled() and converted extern inline to static inline
No auxio on LEON
apbuart: Use of_find_node_by_path to find root node.
sparc: Replace old style lock initializer
sparc: Make atomic locks raw
apbuart: Fix build and missing driver unregister.
apbuart: Kill dependency on deprecated Sparc-only PROM interfaces.
apbuart: Fix build warning.
sparc: Support for GRLIB APBUART serial port
watchdog: Remove BKL from rio watchdog driver
sparc: Remove BKL from apc
sparc,leon: Sparc-Leon SMP support
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
security/tomoyo: Remove now unnecessary handling of security_sysctl.
security/tomoyo: Add a special case to handle accesses through the internal proc mount.
sysctl: Drop & in front of every proc_handler.
sysctl: Remove CTL_NONE and CTL_UNNUMBERED
sysctl: kill dead ctl_handler definitions.
sysctl: Remove the last of the generic binary sysctl support
sysctl net: Remove unused binary sysctl code
sysctl security/tomoyo: Don't look at ctl_name
sysctl arm: Remove binary sysctl support
sysctl x86: Remove dead binary sysctl support
sysctl sh: Remove dead binary sysctl support
sysctl powerpc: Remove dead binary sysctl support
sysctl ia64: Remove dead binary sysctl support
sysctl s390: Remove dead sysctl binary support
sysctl frv: Remove dead binary sysctl support
sysctl mips/lasat: Remove dead binary sysctl support
sysctl drivers: Remove dead binary sysctl support
sysctl crypto: Remove dead binary sysctl support
sysctl security/keys: Remove dead binary sysctl support
sysctl kernel: Remove binary sysctl logic
...
Larry Finger [Sun, 6 Dec 2009 01:25:22 +0000 (19:25 -0600)]
rtl8187: Fix wrong rfkill switch mask for some models
There are different bits used to convey the setting of the rfkill
switch to the driver. The current driver only supports one of these
possibilities. These changes were derived from the latest version
of the vendor driver.
This patch fixes the regression noted in kernel Bugzilla #14743.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-and-tested-by: Antti Kaijanmäki <antti@kaijanmaki.net> Tested-by: Hin-Tak Leung <hintak.leung@gmail.com> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 5 Dec 2009 17:08:05 +0000 (18:08 +0100)]
ath9k: fix tx status reporting
This patch fixes a bug in ath9k's tx status check, which
caused mac80211 to consider regularly transmitted unicast frames
as un-acked.
When checking the ts_status field for errors, it needs to be masked
with ATH9K_TXERR_FILT, because this field also contains other fields
like ATH9K_TX_ACKED.
Without this patch, AP mode is pretty much unusable, as hostapd
checks the ACK status for the frames that it injects.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: Fix bug in computing crc over dynamic IEs in beacon
On a 32-bit machine, BIT() macro does not give the required
bit value if the bit is mroe than 31. In ieee802_11_parse_elems_crc(),
BIT() is suppossed to get the bit value more than 31 (42 (id of ERP_INFO_IE),
37 (CHANNEL_SWITCH_IE), (42), 32 (POWER_CONSTRAINT_IE), 45 (HT_CAP_IE),
61 (HT_INFO_IE)). As we do not get the required bit value for the above
IEs, crc over these IEs are never calculated, so any dynamic change in these
IEs after the association is not really handled on 32-bit platforms.
This patch fixes this issue.
Cc: stable@kernel.org Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrew Morton [Fri, 4 Dec 2009 04:45:07 +0000 (20:45 -0800)]
net/rfkill/core.c: work around gcc-4.0.2 silliness
net/rfkill/core.c: In function 'rfkill_type_show':
net/rfkill/core.c:610: warning: control may reach end of non-void function 'rfkill_get_type_str' being inlined
A gcc bug, but simple enough to squish.
Cc: John W. Linville <linville@tuxdriver.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: don't complain about oversized beacons in FINALIZE_JOIN
The FINALIZE_JOIN firmware command only looks at the first couple of
fields in the beacon, and therefore it's not necessary to complain if
the beacon is longer than 128 bytes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: don't overwrite mwl8k_vif::bssid until after disassociation
When disassociating, mac80211 zeroes vif->bss_info.bssid before
calling our ->bss_info_changed(), but we need the BSSID to remove the
hardware station database entry for our AP, so we can't clear our
local copy of the BSSID until after we've done that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time between loading the helper image and starting to upload the
main firmware image should be at least 5 ms or so. We were doing an
msleep(1) before, and 1 ms appears to not be enough in almost all
cases, but building with HZ=100 has always masked this so far. Bumping
the msleep argument to 5 fixes firmware loading e.g. when HZ=1000.
Some firmware images need more than 200ms to initialize. Bump the
ready code timeout to 500ms to accommodate for this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: allow more time for transmit rings to drain
Before issuing any firmware commands, we wait for the transmit rings
to drain, to prevent control versus data path synchronization issues.
In some cases, this can end up taking longer than the current hardcoded
limit of 5 seconds, for example if the transmit rings are filled with
packets for a host that has dropped off the air and we end up
retransmitting every pending packet at the lowest rate a couple of
times.
This patch changes mwl8k_tx_wait_empty() to only bail out on timeout
expiry if there was no change in the number of packets pending in the
transmit rings during the waiting period. If at least one transmit
ring entry was reclaimed while we were waiting, we are apparently still
making progress, and we'll allow waiting for another timeout period.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: allow more time for firmware commands to complete
Some firmware commands can under some circumstances take more than 2
seconds to complete. This patch bumps the timeout up to 10 seconds,
and prints a message whenever a command takes more than 2 seconds.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: properly report rate on received 40MHz packets
On 8366, bit 6 in the rx descriptor rate field indicates whether the
packet was received on a 20MHz or 40MHz channel, and is not part of
the MCS index. Handle this properly, which then prevents hitting the
WARN_ON and being dropped in ieee80211_rx().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k: fix addr4 zeroing and payload overwrite on DMA header creation
When inserting a DMA header into a packet for transmission,
mwl8k_add_dma_header() would blindly zero the addr4 field, which
is not a good idea if the packet being transmitted is actually a
4-address packet.
Also, if the transmitted packet was a 4-address with QoS packet,
the memmove() to do the needed header reshuffling would inadvertently
overwrite the first two bytes of the packet payload with the QoS field.
This fixes both of these issues.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packets exchanged between the mwl8k driver and the firmware always
have a 4-address header without QoS field. For QoS packets, the QoS
field is passed to/from the firmware via the tx/rx descriptors.
We were handling this correctly on transmit, but not on receive -- if
a QoS packet was received, we would leave garbage in the QoS field in
the packet passed up to the stack, which is Bad(tm).
Also, if the packet received on the air was a 4-address without QoS
packet, we would forget to skb_pull the 2-byte DMA length prefix off.
This patch adds an argument to the ->rxd_process() receive descriptor
operation to retrieve the QoS field from the receive descriptor, and
extends mwl8k_remove_dma_header() to insert this field back into the
packet if the packet received is a QoS packet. It also fixes
mwl8k_remove_dma_header() to strip off the length prefix in all cases.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
There exist 12 802.11b/g rates, but mwl8k supports two additional
(non-standard) rates, and includes those rates in rate bitmasks and
in its internal rate table that hardware rate indices index.
Commit "mwl8k: report rate and other information for received frames"
added one of the nonstandard rates to the mwl8k_rates table to make
the OFDM rates in the table line up with the rate indices that are
reported in the receive descriptor (so that we can just simply copy
the receive descriptor rate index into ieee80211_rx_status::rate_idx)
and bumped MWL8K_IEEE_LEGACY_DATA_RATES from 12 to 13, but this
screwed up the UPDATE_STADB command struct layout, as it also uses
that define, for its legacy_rates array.
To avoid having to convert rate indices and legacy rate bitmaps (e.g.
ieee80211_bss_conf::basic_rates) between the 12-rate mac80211 format
and the 14-rate mwl8k format, we'll report all 14 rates in our wiphy's
band, but filter out the nonstandard ones e.g. in the case of the
UPDATE_STADB command which only accepts 12 rates.
In the commands that accept 14 rates (SET_AID, SET_RATE), replace the
use of the MWL8K_RATE_INDEX_MAX_ARRAY define in the command struct by
the constant 14, to make it clearer that these commands accept 14 rates.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MCS bitmaps in the SET_RATE command structure were of the wrong
size, due to use of the wrong define for the array length. Just
hardcode the lengths as 16, and do the same for the MCS bitmaps in
other command structures.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Mon, 30 Nov 2009 11:20:53 +0000 (16:50 +0530)]
mac80211: Fix dynamic power save for scanning.
Not only ps_sdata but also IEEE80211_CONF_PS is to be considered
before restoring PS in scan_ps_disable(). For instance, when ps_sdata
is set but CONF_PS is not set just because the dynamic timer is still
running, a sw scan leads to setting of CONF_PS in scan_ps_disable
instead of restarting the dynamic PS timer.
Also for the above case, a null data frame is to be sent after
returning to operating channel which was not happening with the
current implementation. This patch fixes this too.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sun, 29 Nov 2009 11:19:06 +0000 (12:19 +0100)]
mac80211: recalculate idle later in MLME
hwsim testing has revealed that when the MLME
recalculates the idle state of the device, it
sometimes does so before sending the final
deauthentication or disassociation frame. This
patch changes the place where the idle state
is recalculated, but of course driver transmit
is typically asynchronous while configuration
is expected to be synchronous, so it doesn't
fix all possible cases yet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: fix warning from ieee80211_stop_tx_ba_cb_irqsafe argument change
CC [M] drivers/net/wireless/iwlwifi/iwl-tx.o
drivers/net/wireless/iwlwifi/iwl-tx.c: In function ‘iwl_tx_agg_stop’:
drivers/net/wireless/iwlwifi/iwl-tx.c:1356: warning: passing argument 1 of ‘ieee80211_stop_tx_ba_cb_irqsafe’ from incompatible pointer type
include/net/mac80211.h:2128: note: expected ‘struct ieee80211_vif *’ but argument is of type ‘struct ieee80211_hw *’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sergei Shtylyov notes "You call min() on uncomparables [in
mwdma_clip_to_pio()], i.e. mwdma_to_pio[] contains XFER_PIO_* and
adev->pio_mode - XFER_PIO_0 yields you a mode number. Thus the second
argument will always "win" as a minimal one"
Bartlomiej Zolnierkiewicz adds "There are more issues with the patch related
to mwdma_clip_to_pio(). The function can return values between 0 and
4 which obviously won't work well for the new code below for values
>2 (i.e. resulting in out-of-bounds array access for the common-case
of dev->pio_mode == XFER_PIO_4)."
Bartlomiej Zolnierkiewicz also notes the patch is incomplete, failing to
update MWDMA mode masks.
Many features of h3100/h3600 (LCD, PCMCIA, Flash write, etc.)
depend on correct functioning of GPIO expander handled by htc-egpio
driver, so force its building in Kconfig.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dmitry Artamonow [Fri, 27 Nov 2009 11:13:01 +0000 (12:13 +0100)]
ARM: 5823/1: SA1100: h3100/h3600: add support for gpio-keys
Add support for "Power" and "Action" (joystick center) buttons -
the only buttons on iPaq h3100/h3600 connected to GPIOs
(other buttons are controlled by microcontroller)
Also remove setting PWER for wakeup on Power button press -
gpio-keys driver will handle it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct boilerplates after files split. Also shorten them a bit - use
standart GPL wording (as per http://lkml.org/lkml/2007/5/1/220) and
drop changelog, which only entry about h3800 support and abstracted
EGPIOs is just confusing now, as both of these features are gone.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dmitry Artamonow [Fri, 27 Nov 2009 11:10:55 +0000 (12:10 +0100)]
ARM: 5820/1: SA1100: h3100/h3600: split h3600.c
Split common h3600.c into three separate files: h3100.c, h3600.c and
h3xxx.c (the latter contains common code for h3100/h3600)
Copyright boilerplates and #includes are copied intact and will be
cleaned up later.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dmitry Artamonow [Fri, 27 Nov 2009 11:07:47 +0000 (12:07 +0100)]
ARM: 5818/1: SA1100: h3100/h3600: drop old GPIO definitions
As all existing code was converted to gpiolib, drop no more
used pre-gpiolib (bit-shifted) GPIO definintions.
Supply new gpiolib-friendly definitions for GPIOs which
don't have them yet.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dmitry Artamonow [Fri, 27 Nov 2009 11:07:11 +0000 (12:07 +0100)]
ARM: 5817/1: SA1100: h3100/h3600: configure all unused gpios as inputs
After conversion to gpiolib there's still some GPIOs left, that get
configured in *_mach_init() as outputs (using direct operations
on GPCR/GPDR registers), but otherwise unused. These GPIOs are mainly
sound related and should be configured by corresponding driver once
it is written.
Drop this initialisation and configure all GPIOs as input.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dmitry Artamonow [Fri, 27 Nov 2009 11:02:28 +0000 (12:02 +0100)]
ARM: 5814/1: SA1100: h3100/h3600: convert all users of assign_h3600_egpio to gpiolib
Use of gpio_request/gpio_free in some callbacks may look ugly, but
corresponding drivers (sa1100_serial and sa1100_fb) don't provide (yet)
init/exit hooks and registering these gpios in *_mach_init is also
not possible, because htc-gpio driver starts a bit later...
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dmitry Artamonow [Fri, 27 Nov 2009 10:58:35 +0000 (11:58 +0100)]
ARM: 5812/1: SA1100: h3100/h3600: separate machine-specific LCD helpers
h3100 and h3600 have different sets of LCD-controlling gpios,
which mapped to the same "abstracted" EGPIO.
As we plan to get rid of those abstracted egpios completely, we
need to separate these helper functions.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jean Delvare [Sun, 6 Dec 2009 16:06:29 +0000 (17:06 +0100)]
i2c-stub: Allow user to disable some commands
Add a module parameter to override the functionality bitfield. This
lets the user disable some commands. This can be used to force a chip
driver to take different code paths.
Jean Delvare [Sun, 6 Dec 2009 16:06:27 +0000 (17:06 +0100)]
i2c: Refactor for_each callbacks
Functions i2c_do_add_adapter() and __attach_adapter() do essentially
the same thing, differing only in how the parameters are passed. Same
for i2c_do_add_adapter() and __detach_adapter(). Introduce wrappers to
normalize the parameters, so that we do not have to duplicate the
code.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <dbrownell@users.sourceforge.net>
Jean Delvare [Sun, 6 Dec 2009 16:06:27 +0000 (17:06 +0100)]
i2c-i801: Retry on lost arbitration
The Intel 82801 is sometimes used on systems with a BMC connected. The
BMC can access the SMBus, resulting in lost arbitration for the 82801.
We should let i2c-core retry transactions for us in this case.
Vincent Sanders [Sun, 6 Dec 2009 16:06:26 +0000 (17:06 +0100)]
i2c: Remove big kernel lock from i2cdev_open
The BKL is held over a kmalloc so cannot protect anything beyond that.
The two calls before the kmalloc have their own locking.
Improve device open function by removing the now unnecessary ret variable
Signed-off-by: Vincent Sanders <vince@simtec.co.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 6 Dec 2009 16:06:24 +0000 (17:06 +0100)]
i2c: Drop probe, ignore and force module parameters
The legacy probe and force module parameters are obsolete now, the
same can be achieved using the new_device sysfs interface, which is
both more flexible and cheaper (it is implemented by i2c-core rather
than replicated in every driver module.)
The legacy ignore module parameters can be dropped as well. Ignoring
can be done by instantiating a "dummy" device at the problematic
address.
This is the first step of a huge cleanup to i2c-core's i2c_detect
function, i2c.h's I2C_CLIENT_INSMOD* macros, and all drivers that made
use of them.
Jean Delvare [Sun, 6 Dec 2009 16:06:22 +0000 (17:06 +0100)]
i2c: Bus drivers don't have to support I2C_M_REV_DIR_ADDR
I2C bus drivers don't have to support I2C_M_REV_DIR_ADDR. It is a
deviation from the I2C specification, which only makes sense to
implement when really needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Ben Dooks <ben-linux@fluff.org>
Mika Kuoppala [Sun, 6 Dec 2009 16:06:22 +0000 (17:06 +0100)]
i2c: Prevent priority inversion on top of bus lock
Low priority thread holding the i2c bus mutex could block higher
priority threads to access the bus resulting in unacceptable
latencies. Change the mutex type to rt_mutex preventing priority
inversion.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@nokia.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 6 Dec 2009 16:06:18 +0000 (17:06 +0100)]
i2c-powermac: Log errors
Log errors when they happen, otherwise we have no idea what went
wrong.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Michel Daenzer <michel@daenzer.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org>
Jean Delvare [Sun, 6 Dec 2009 16:06:17 +0000 (17:06 +0100)]
i2c-powermac: Refactor i2c_powermac_smbus_xfer
I wanted to add some error logging to the i2c-powermac driver, but
found that it was very difficult due to the way the
i2c_powermac_smbus_xfer function is organized. Refactor the code in
this function so that each low-level function is only called once.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Michel Daenzer <michel@daenzer.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org>
Jean Delvare [Sun, 6 Dec 2009 16:06:17 +0000 (17:06 +0100)]
i2c-powermac: Reject unsupported I2C transactions
The i2c-powermac driver doesn't support arbitrary multi-message I2C
transactions, only SMBus ones. Make it clear by returning an error if
a multi-message I2C transaction is attempted. This is better than only
processing the first message, because most callers won't recover from
the short transaction. Anyone wishing to issue multi-message
transactions should use the SMBus API instead of the raw I2C API.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Tested-by: Michel Daenzer <michel@daenzer.net> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org>
Wolfram Sang [Sun, 6 Dec 2009 16:06:16 +0000 (17:06 +0100)]
i2c/chips: Move ds1682 to drivers/misc
As i2c/chips is deprecated, move ds1682 to a more apropriate location.
Build tested.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jean Delvare <khali@linux-fr.org>
PM: Add flag for devices capable of generating run-time wake-up events
Apparently, there are devices that can wake up the system from sleep
states and yet are incapable of generating wake-up events at run
time. Thus, introduce a flag indicating if given device is capable
of generating run-time wake-up events.