vxge: Fix starvation of receive ring controller when blasted by short packets.
- Fix starvation of receive ring controller when blasted by short packets. This was because the driver was posting 64 rxds initially while the ring controller
was expecting to read 256 replenished rxds. While the driver was coming up,
the internal rxd memory filled up the 64 buffers provided and the ring
controller was left waiting for the remaining 192 rxds to complete the write
back of completed rxds to the host and generation of an interrupt.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vxge: Fix a receive stall due to driver being out of synch with chip.
- Fix a receive stall due to driver being out of synch with chip. In a corner
case scenario the adapter's ring controller may return a RxD with transfer code
of 0xC, while the host ownership bit is still set to the adapter. The driver
needs to assume that this case where (host_ownership == 1 or adapter) and
(transfer_code == 0xC) is valid, that is, this RxD has been returned by the
receive ring controller but no frame data is associated with the rxd.
- Restore the transfer code field of each newly replenished RxD to 0x0.
- Code cleanup. Removed usage of magic numbers.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
For NX2031, msix is supported from fw version > 3.4.336.
This fw version check should take flash fw in consider instead of
running fw or fw from file. Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Validate all sections of unified romimage, before accessing them,
to avoid seg fault.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
o DEV_NEED_RESET state was not handled during fw intialization phase.
o nx_decr_dev_ref_cnt() can return error, if fail to grab pcie seamphore. Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel default tx csum function (ethtool_op_get_tx_csum) doesn't show
correct csum status. It takes various FLAGS (NETIF_F_ALL_CSUM) in account
to show tx csum status, which driver doesn't set while disabling tx csum.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Rothwell [Mon, 29 Mar 2010 08:00:44 +0000 (01:00 -0700)]
rps: fix net-sysfs build for !CONFIG_RPS
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Sun, 28 Mar 2010 00:15:29 +0000 (17:15 -0700)]
net: increase preallocated size of nlmsg to accomodate for IFLA_STATS64
When more data is stuffed into an nlmsg than initially projected, an
extra allocation needs to be done. Reserve enough for IFLA_STATS64 so
that this does not to needlessy happen.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Sat, 27 Mar 2010 23:35:50 +0000 (16:35 -0700)]
net: fix unaligned access in IFLA_STATS64
Tony Luck observes that the original IFLA_STATS64 submission causes
unaligned accesses. This is because nla_data() returns a pointer to a
memory region that is only aligned to 32 bits. Do some memcpying to
workaround this.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Wed, 24 Mar 2010 12:55:30 +0000 (12:55 +0000)]
e1000e: Use pr_<level> and netdev_<level>
As an alternative to a quite large patch previously submitted by Joe
Perches to make use of kernel logging API, this patch is much less
intrusive.
Convert e_<level> to netdev_<level>
Use #define pr_fmt
Convert a few printks to pr_<level>
Cc: Joe Perches <joe@perches.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 23 Mar 2010 22:58:20 +0000 (22:58 +0000)]
ixgbevf: convert to use netdev_for_each_mc_addr
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 23 Mar 2010 22:58:01 +0000 (22:58 +0000)]
ixgbe: convert to use netdev_for_each_mc_addr
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 24 Mar 2010 19:13:54 +0000 (19:13 +0000)]
rps: add CONFIG_RPS
RPS currently depends on SMP and SYSFS
Adding a CONFIG_RPS makes sense in case this requirement changes in the
future. This patch saves about 1500 bytes of kernel text in case SMP is
on but SYSFS is off.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Wed, 24 Mar 2010 21:21:08 +0000 (17:21 -0400)]
iwlwifi: fix build error for CONFIG_IWLAGN=n
drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_good_ack_health':
drivers/net/wireless/iwlwifi/iwl-rx.c:647: error: 'struct iwl_priv' has no member named '_agn'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frans Pop [Wed, 24 Mar 2010 07:57:31 +0000 (07:57 +0000)]
net/ps3_gelic: remove trailing space in messages
ps3_gelic_wireless.c: also remove a stray "p" after a newline.
Signed-off-by: Frans Pop <elendil@planet.nl> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linuxppc-dev@ozlabs.org Signed-off-by: David S. Miller <davem@davemloft.net>
Frans Pop [Wed, 24 Mar 2010 07:57:29 +0000 (07:57 +0000)]
tipc: remove trailing space in messages
Signed-off-by: Frans Pop <elendil@planet.nl> Cc: Per Liden <per.liden@ericsson.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Juuso Oikarinen [Wed, 24 Mar 2010 08:11:14 +0000 (10:11 +0200)]
cfg80211: Improve connection quality maintenance docs in nl80211.h
In nl80211.h, be a little more elaborate in the docs for the definitions
NL80211_ATTR_CQM_RSSI_THOLD and NL80211_ATTR_CQM_RSSI_HYST.
Reported-by: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Tue, 23 Mar 2010 07:02:34 +0000 (09:02 +0200)]
mac80211: Add support for connection quality monitoring
Add support for the set_cqm_config op. This op function configures the
requested connection quality monitor rssi threshold and rssi hysteresis
values to the hardware if the hardware supports
IEEE80211_HW_SUPPORTS_CQM.
For unsupported hardware, currently -EOPNOTSUPP is returned, so the mac80211
is currently not doing connection quality monitoring on the host. This could be
added later, if needed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Tue, 23 Mar 2010 07:02:33 +0000 (09:02 +0200)]
cfg80211: Add connection quality monitoring support to nl80211
Add support for basic configuration of a connection quality monitoring to the
nl80211 interface, and basic support for notifying about triggered monitoring
events.
Via this interface a user-space connection manager may configure and receive
pre-warning events of deteriorating WLAN connection quality, and start
preparing for roaming in advance, before the connection is already lost.
An example usage of such a trigger is starting scanning for nearby AP's in
an attempt to find one with better connection quality, and associate to it
before the connection characteristics of the existing connection become too bad
or the association is even lost, leading in a prolonged delay in connectivity.
The interface currently supports only RSSI, but it could be later extended
to include other parameters, such as signal-to-noise ratio, if need for that
arises.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Fri, 26 Feb 2010 01:16:36 +0000 (17:16 -0800)]
libertas: add auto auth mode feature
Auto auth mode is enabled by default. If user doesn't specify the
auth mode, while association driver will first try with open mode
and then with shared key mode. If user specifies an auth mode,
auto auth is disabled and driver will not try association with
another auth mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 19 Mar 2010 05:14:53 +0000 (07:14 +0200)]
mac80211: Add support for connection monitor in hardware
This patch is based on a RFC patch by Kalle Valo.
The wl1271 has a feature which handles the connection monitor logic
in hardware, basically sending periodically nullfunc frames and reporting
to the host if AP is lost, after attempting to recover by sending
probe-requests to the AP.
Add support to mac80211 by adding a new flag IEEE80211_HW_CONNECTION_MONITOR
which prevents conn_mon_timer from triggering during idle periods, and
prevents sending probe-requests to the AP if beacon-loss is indicated by the
hardware.
Cc: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 19 Mar 2010 01:29:40 +0000 (18:29 -0700)]
drivers/net/wireless/ray_cs.c: Use iw_handler function prototypes
Change local functions that are cast to iw_handler to
the more standard use with "union iwreq_data *wrqu"
so the iw_handler array no longer needs the casts.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Thu, 18 Mar 2010 10:26:46 +0000 (12:26 +0200)]
wl1271: Changed platform_device to be dynamically allocated
Changed platform_device to be allocated dynamically from the
wl1271_alloc_hw function. Also cleaned up error handling in the
wl1271_alloc_hw function and module probe functions.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:45 +0000 (12:26 +0200)]
wl1271: Remove circular interlocking related to the inetaddr notifier chain
Removing the wl1271 from the inet addr notifier chain sometimes causes the
registered handler to be called - causing locking problems if the removing
function is called from within the mutex.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:40 +0000 (12:26 +0200)]
wl1271: Remove deprecated interface config function
It's no longer needed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:39 +0000 (12:26 +0200)]
wl1271: Fix MAC address handling
This patch fixes MAC address handling. To achieve this, firmware booting had
to be delayed from the previous op_start to op_add_interface, which is the point
when the driver gets to know the configured MAC address. As the wl1271 only
supports one virtual interface, this even seems quite logical.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:30 +0000 (12:26 +0200)]
wl1271: Add proper WLAN-BT co-ex configuration, and enable co-ex.
Add configuration values for the varous WLAN-BT co-ex configuration parameters,
and finally enable WLAN-BT co-ex. Based on preliminary measurements, it
appears the co-ex feature is not increasing WLAN power consumption, if BT
is not activated.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:29 +0000 (12:26 +0200)]
wl1271: Fix SG configuration message structures
The bluetooth coexistence (SG) configuration messages have changed and
were completely wrong. For instance, intending to enable the SG, it was
instead disabled.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 18 Mar 2010 10:26:26 +0000 (12:26 +0200)]
wl1271: Fix configuration of the TX opportunity value
The per-queue TX opportunity value is configured by the mac80211 in units
of 32us. The firmware however wants it in us, so add the conversion.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:24 +0000 (14:25 +0530)]
ath9k_hw: fix hardware deinit
Without this you will get a panic if the device initialization
fails. Also, free ath_hw instance properly. ath9k_hw_deinit()
shouldn't do it.
Cc: stable@kernel.org Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:23 +0000 (14:25 +0530)]
ath9k_hw: add HTC init hardware call for special resets for AR9271
AR9271 needs a full reset only upon the first reset, add
a call for the driver to enable these special resets. We
can optimize this out later without an export.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:22 +0000 (14:25 +0530)]
ath9k_hw: always set the core clock for AR9271
When initializing the PLL on AR9271 we always need
to set the core clock to 117MHz. While at it remove
the baud rate settings for the serial device on the
AR9271, the default settings work well unless you
want to customize it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:21 +0000 (14:25 +0530)]
ath9k_hw: use the skip count for PA calibration on AR9271
Periodic power amplifier offset calibration is skipped on ath9k
algorithmically, this is required on AR9271.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:20 +0000 (14:25 +0530)]
ath9k_hw: restrict valid nf readings for AR9271 to -114
Noisefloor values read on AR9271 are unreliable if they
are less than -114, set those statically to -116.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:19 +0000 (14:25 +0530)]
ath9k_hw: fix noisefloor history buffer usage on AR9271
Noisefloor calibration involves querying hardware for samples
and storing this information on a history buffer in hardware for
actual noisefloor calibration processing in hardware. The history
buffer supports collecting information for all Atheros hardware,
one history buffer slot for each chain on each channel used for
MIMO operation. For current hardware this means one history
buffer slot for each chain on both the control (or primary) channel
and the extension (or secondary) channel. We know which noisefloor
registers to poke for collecting noisefloor data through the
chainmask.
For AR9285 and AR9271 devices, both 1x1, the chaimmask is defined as
0x9 = 0b0001001. The first four bits represent each chain out of
a maximum of 4 chains [0-3] on the primary channel. The last four
bits represent each chain on the extension channel. A chainmask
of 0x9 therefore indicates chain 1 is active on both the primary
and the extension channel.
AR9271 only requires collecting and storing noisefloor history buffer
data for the first chain on both the control and extension channel
(nfarray[0] and nfarray[3]) so fix the code and avoid which reads
and writes to the history buffer for the other chains.
Since the noisefloor varies depending on the number of chains your
device supports also initialize the noisefloor history buffer with
reasonable values seen on 1x1 devices such as AR9285.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:18 +0000 (14:25 +0530)]
ath9k_hw: Fix full sleep setup for AR9271
After telling the AR9271 to go into full sleep we do not need
to clear the RTC reset signal.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:17 +0000 (14:25 +0530)]
ath9k_hw: fix TX descriptor setup for AR9271
The TX descriptors setup for AR971 requires the same
setup as AR9285, so use that.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:16 +0000 (14:25 +0530)]
ath9k_hw: skip chip tests for AR9271
The chip test is not required for AR9271 on the host driver
code as the firmware will do the test internally on its own.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:15 +0000 (14:25 +0530)]
ath9k_hw: add GPIO setup code for AR9271
Assign the proper number of GPIO pins for AR9271.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Wed, 17 Mar 2010 08:55:14 +0000 (14:25 +0530)]
ath9k_hw: update initialization values for AR9271
Update the register initialization values for AR9271.
This is based on our last review from our systems team.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ming Lei [Mon, 1 Mar 2010 15:13:29 +0000 (23:13 +0800)]
ath9k: decrease size of ath9k.ko
From e74b075cdb143d45be9b371ee8a8e2dcfc15ab34 Mon Sep 17 00:00:00 2001
From: Ming Lei <tom.leiming@gmail.com>
Date: Sat, 27 Feb 2010 23:50:54 +0800
Subject: [PATCH] ath9k: decrease size of ath9k.ko
The patch defines the fields of 'valid_single_stream' and 'valid' in
struct ath_rate_table as char type, so decrease the size of ath9k.ko
about 2KB.
old ath9k.ko
[tom@tom-lei ath9k]$ size ath9k.ko
text data bss dec hex filename
69344 3080 168 72592 11b90 ath9k.ko
new ath9k.ko
[tom@tom-lei ath9k]$ size ath9k.ko
text data bss dec hex filename
67304 3080 168 70552 11398 ath9k.ko
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sathya Perla [Mon, 22 Mar 2010 20:41:34 +0000 (20:41 +0000)]
be2net: fix unmap_single/page() called incorrectly in Tx compl processing
The first wrb seen by tx compl processing does not have a dma handle in it.
Currently, pci_unmap_single() is attempted on this wrb and pci_unmap_page() on the
rest. So, pci_unmap_page() gets incorrectly called on the dma hdl of skb->data (that
was mapped using map_single()). This patch fixes this issue.
Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Mon, 22 Mar 2010 03:21:39 +0000 (03:21 +0000)]
ipoib: remove addrlen check for mc addresses
Finally this bit can be removed. Currently, after the bonding driver is
changed/fixed (32a806c194ea112cfab00f558482dd97bee5e44e net-next-2.6),
that's not possible for an addr with different length than dev->addr_len
to be present in list. Removing this check as in new mc_list there will be
no addrlen in the record.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amerigo Wang [Sun, 21 Mar 2010 23:59:23 +0000 (23:59 +0000)]
netconsole: do not depend on experimental
Nowadays, most distributions enable netconsole by default,
including RHEL, Fedora, Debian, Arch, Opensuse. And
we don't have any bug reports about it. So I think there
is no need to mark it as experimental any more.
Cc: David S. Miller <davem@davemloft.net> Signed-off-by: WANG Cong <amwang@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 22 Mar 2010 14:08:06 +0000 (14:08 +0000)]
igb: add support for Intel I350 Gigabit Network Connection
This patch adds support for the the I350 Gigabit network connection which
is the follow-on part to the 82580.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> CC: James Hearn <james.r.hearn@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 22 Mar 2010 14:07:46 +0000 (14:07 +0000)]
igb: cleanup usage of virtualization registers
The igb driver was incorrectly attempting to write to registers that do not
exist on 82580 hardware. This wasn't causing any issues that I can tell,
but it is not recommended behavior either so I have changed this so we are
determining which registers to write to based on mac type.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 22 Mar 2010 14:07:26 +0000 (14:07 +0000)]
igb: Do not overwrite mdicnfg register when accessing 82580 phy
This change removes the extra configuration we were doing on the mdicnfg
register which should be set by EEPROM and which we should not need to
write again afterwards. This code was a holdover from some earlier
development work that was being done on a board with an incomplete EEPROM
and is no longer needed now that the production EEPROMs are in place.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Blaschka [Mon, 22 Mar 2010 16:59:48 +0000 (09:59 -0700)]
qeth: l3 fix build error in ipv6 addr list handling
Adapt qeth l3 to:
commit c2e21293c054817c42eb5fa9c613d2ad51954136
(ipv6: convert addrconf list to hlist)
converted lst_next member of inet6_ifaddr struct to a hlist.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>