Takashi Iwai [Thu, 10 May 2012 14:11:15 +0000 (16:11 +0200)]
ALSA: hda - Fix concurrent hash accesses
The amp and caps hashes aren't protected properly for concurrent
accesses. Protect them via a new mutex now.
But it can't be so simple as originally thought: since the update of a
hash table entry itself might trigger the power-up sequence which
again accesses the hash table, we can't cover the whole function
simply via mutex. Thus the update part has to be split from the mutex
and revalidated.
Takashi Iwai [Tue, 8 May 2012 08:34:08 +0000 (10:34 +0200)]
ALSA: hda - Add the support for Creative SoundCore3D
The controller is compatible with HD-audio 1.0a with some specific
restrictions.
- The BDLE entries can't be over 4k boundary
- No position-buffer and no MSI
Takashi Iwai [Wed, 9 May 2012 10:36:22 +0000 (12:36 +0200)]
ALSA: hda - More robustify the power-up/down sequence
Check the power_transition up/down state instead of boolean bit, so
that the power-up sequence can cancel the pending power-down work
properly. Also, by moving cancel_delayed_work_sync() before the
actual power-up sequence, make sure that the delayed power-down is
completed.
Takashi Iwai [Wed, 9 May 2012 08:31:08 +0000 (10:31 +0200)]
ALSA: hda - Remove pre_resume and post_suspend ops
Since the recent commit, the resume procedure is always performed at
the resume time. This makes the pre_resume hack for VREF mute LED on
some HP laptops superfluous. As this is the only user of pre_resume
(and there is no user of post_suspend) ops, let's kill them again.
Takashi Iwai [Tue, 8 May 2012 14:57:12 +0000 (16:57 +0200)]
ALSA: hda - Clear the power-saving states properly at reset
Some power-saving states have been left unchanged in
snd_hda_codec_reset(), and this is a potential danger because the
function may be called in various situations including the continuous
operation after that call.
Takashi Iwai [Tue, 8 May 2012 14:52:23 +0000 (16:52 +0200)]
ALSA: hda - Always resume the codec immediately
This is a fix for the problem in commit 785f857d1c, the pop noise
issue on some machines with ALC269. The problem was the uninitialized
state after the resume due to the delayed resume of the codec chips.
In that commit, we tried to fix by forcibly putting the codec to D3 at
suspend. But, this still also leaves the uninitialized state after
resume, and it _might_ be still problematic with some BIOS. Since the
commit turned out to regress another issues, we reverted it in the
end.
Now, in this fix, try to fix by turning on the codec immediately at
the resume path. We need to take care of the power-saving in this
case. When the device is woken up at the power-saved state, it should
go power-saving again after the resume.
The commit causes a problem with the wrong D3 state after suspend
because the call of hda_set_power_state() involves with the power-up
sequence, which changes the power_count, and this confuses the resume
sequence that checks the power_count as well.
Originally, this go-to-D3 sequence should be a simple task without the
power-up sequence. But, it'd need some proper sanity checks in the
case of power-saved state, so it's not too easy to write now in the
3.4-rc cycle.
In short, the safest option now is to revert this affecting commit.
Of course, we need to clean up and robustify the power-saving code
better for 3.5 kernel.
Reported-by: Konstantin Khlebnikov <khlebnikov@openvz.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 7 May 2012 16:09:48 +0000 (18:09 +0200)]
ALSA: hda/realtek - Call alc_auto_parse_customize_define() always after fixup
The call for alc_auto_parse_customize_define() must be done after the
fixup pre-probe initialization. Otherwise SKU_IGNORE fixup won't work
properly (e.g. HP RP5800 with ALC662 codec).
Andre Schramm [Mon, 7 May 2012 16:52:51 +0000 (18:52 +0200)]
ALSA: hdsp - Provide ioctl_compat
snd_hdsp uses its own ioctls to acquire config- and status information.
Expose the corresponding ioctl handler via ioctl_compat, so that 32bit applications can use it on 64bit kernels.
Signed-off-by: Andre Schramm <andre.schramm@iosono-sound.com> Reviewed-by: Adrian Knoth <adi@drcomp.erfurt.thur.de> Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Hills [Mon, 30 Apr 2012 18:39:22 +0000 (19:39 +0100)]
ALSA: echoaudio: Remove incorrect part of assertion
This assertion seems to imply that chip->dsp_code_to_load is a pointer.
It's actually an integer handle on the actual firmware, and 0 has no
special meaning.
The assertion prevents initialisation of a Darla20 card, but would also
affect other models. It seems it was introduced in commit dd7b254d.
ASoC: omap-pcm: Free dma buffers in case of error.
Signed-off-by: Oleg Matcovschi <oleg.matcovschi@ti.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@ti.com>
Mark Brown [Mon, 30 Apr 2012 19:11:55 +0000 (20:11 +0100)]
ASoC: wm8350: Don't use locally allocated codec struct
The core allocates the live copies, we shouldn't try to duplicate it and
were buggy trying to do so as we were using uninitialised data for the
control data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Eric Bénard [Sun, 29 Apr 2012 15:37:57 +0000 (17:37 +0200)]
ASoC: tlv312aic23: unbreak resume
* commit f9dfbf9 "ASoC: tlv320aic23: convert to soc-cache" leads to
a bug preventing resumeof the codec as regmap expects a 9 bits data
register but 0xFFFF is passed in tlv320aic23_set_bias_level and this
values gets cached preventing any write to the TLV320AIC23_PWR
register as the final value produced by regmap is (register << 9) | value
* this patch solves the problem by only working on the 9 bits the
register contains.
Signed-off-by: Eric Bénard <eric@eukrea.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org
Commit 980b0bc69 ("ASoC: blackfin: Use dai_fmt") converted the blackfin ASoC
machine drivers to use the dai_links dai_fmt field to setup their DAI format.
For the bf5xx-ssm2602 the commit removed the manual call to snd_soc_dai_set_fmt,
but missed to set the dai_links dai_fmt field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: updates for 3.4
Slightly larger than normal - the DAPM fix is a "this should always have
worked" type of thing which is very clear and should have no impact on
systems that don't need it. The WM8994 fix is driver specific but
pretty important for that driver.
Some old codecs like ALC880 seem to give a bogus pin capability value 0
occasionally. This breaks the new sanity check in snd_hda_set_pin_ctl().
Skip the sanity checks in such a case.
ALSA: hda - Add snd_hda_get_default_vref() helper function
Add a new helper function to guess the default VREF pin control bits
for mic in. This can be used to set the pin control value safely
matching with the actual pin capabilities.
For setting the pin-control values more safely to match with the
actual pin capability bits, a copule of new helper functions,
snd_hda_set_pin_ctl() and snd_hda_set_pin_ctl_cache(), are
introduced. These are simple replacement of the codec verb write with
AC_VERB_SET_PIN_WIDGET but do more sanity checks and filter out
superfluous pin-control bits if they don't fit with the corresponding
pin capabilities.
Some codecs are screwed up or ignore the command when such a wrong bit
is set. These helpers will avoid such secret errors.
ALSA: HDA: Add external mic quirk for Asus Zenbook UX31E
According to the reporter, external mic starts to work if the
laptop-dmic model is used. According to BIOS pin config, all
pins are consistent with the alc269vb_laptop_dmic fixup, except
for the external mic, which is not present.
Merge fixes for Thinkpad docking-station regressions for 3.3 kernels
back to 3.4. These were committed in that branch to make the stable
merging easier.
ALSA: hda/conexant - Set up the missing docking-station pins
ThinkPad 410,420,510,520 and X201 with cx50585 & co chips have the
docking-station ports, but BIOS doesn't initialize for these pins.
Thus, like the former X200, we need to set up the pins manually in the
driver.
The odd part is that the same PCI SSID is used for X200 and T400, thus
we need to prepare individual fixup tables for cx5051 and others.
ALSA: workaround: change the timing of alsa_sound_last_init()
Current alsa_sound_last_init() was called as __initcall().
So, on current ALSA, only devices that had been properly
registered at this point were shown.
So, it will show "No soundcards found" if driver requests
probe deferment. it's often misleading.
This patch delays the timing of alsa_sound_last_init()
as workaround.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
While refactoring the mute-LED handling for HP laptops, I messed up
the polarity check in a wrong way. The red (or the mute-LED if any)
should appear in the muted state, corresponding to GPIO on.
Reported-by: Mikko Vinni <mmvinni@yahoo.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Paul Mundt [Wed, 18 Apr 2012 02:13:04 +0000 (19:13 -0700)]
ASoC: fsi: update for dmaengine prep_slave_sg fallout.
Leading up to the ->device_prep_slave_sg change in 185ecb5f4fd43911c35956d4cc7d94a1da30417f 'dmaengine: add context
parameter to prep_slave_sg and prep_dma_cyclic' a generic wrapper was
added in place to guard against the API change, though the fsi driver
wasn't updated in the process (presumably its dmaengine support hadn't
been merged yet at the time). This trivially switches over to the new
wrapper and gets it building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: core: Fix card RTD count for deferred probe.
Currently we increment the number of RTD's per card during the DAI link
bind. This can cause an incorrect RTD count when we cannot find a component
and defer the probe (and hence perform the DAI link bind for the card again).
Fix the count so that it is cleared before every card registration
and bind attempt.
Signed-off-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If cs42l73_get_mclkx_coeff() returns < 0 (which it can) in
sound/soc/codecs/cs42l73.c::cs42l73_set_mclk(), then we'll be using
the (negative) return value as array index on the very next line of
code - that's bad.
Catch the negative return value and propagate it to the caller (which
checks for it) and things are a bit more sane :-)
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
In sound/pci/hda/patch_realtek.c::alc_auto_fill_dac_nids(), in the
'for (;;)' loop, if the 'badness' value returned from
fill_and_eval_dacs() is negative, then we'll return from the function
without freeing the memory we allocated for 'best_cfg', thus leaking.
Fix the leak by kfree()'ing the memory when badness is negative.
While I was there I also noticed some trailing whitespace in the
function that I removed (along with all other trailing whitespace in
the file) - it didn't seem worth-while to do that as two patches, so I
hope it's OK that I just did it all as one patch.
Mark Brown [Thu, 12 Apr 2012 16:29:36 +0000 (17:29 +0100)]
ASoC: dapm: Ensure power gets managed for line widgets
Line widgets had not been included in either the power up or power down
sequences so if a widget had an event associated with it that event would
never be run. Fix this minimally by adding them to the sequences, we
should probably be doing away with the specific widget types as they all
have the same priority anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org
ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
A user reported that setting model=imac24 used to allow sound to work on their
Mac Pro 5,1 machine. Commit 5671087ffa "Move ALC885 macpro and imac24 models
to auto-parser" removed this model option. All Mac machines are now explicitly
handled with a quirk and the auto-parser. This adds a quirk for the device
found on the Mac Pro 5,1 machines.
This (partially) fixes https://bugzilla.redhat.com/show_bug.cgi?id=808559
[sorted the new entry in the ID number order by tiwai]
ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
Add GPIO1 setup explicitly for Acer Aspire 493x & co.
This could be set by alc_auto_init_amp(), but it's safer to set it
more explicitly in the fixup table.
ALSA: hda/realtek - Add a few ALC882 model strings back
Since there are still many Acer models that might not be covered by
the current fixup table, let's add back a few typical model names so
that user can test the fixup without recompiling.
At the point of this error-handling code, both regions and the dma have
been allocated, so free it as done in previous and subsequent
error-handling code.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Julia Lawall [Mon, 9 Apr 2012 08:16:32 +0000 (10:16 +0200)]
sound: sound/oss/msnd_pinnacle.c: add vfrees
At the point of this error-handling code, HAVE_DSPCODEH may be undefined,
so free INITCODE and PERMCODE as done elsewhere. A jump and label are
introduced to avoid code duplication.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: fixes for 3.4
A bunch of driver-specific fixes and one generic fix for the new support
for platform DAPM contexts - we were picking the wrong default for the
idle_bias_off setting which was meaning we weren't actually achieving
any useful runtime PM on platform devices.
Michael Karcher [Fri, 6 Apr 2012 13:34:18 +0000 (15:34 +0200)]
ALSA: hda - Remove CD control from model=benq for CX20549
The ID used for detection of the BenQ R55E actually identifies the
Quanta TW3 ODM design, which is also used for the Gigabyte W551 laptop
series. Schematics on the internet clearly indicate that the "Port C"
(analog input connected to record source #4 and mixer input #4) is
unconnected.
Playing an audio CD through analog playback (using cdplay from cdtools)
produces no sound, even with the mixer input labelled "CD" enabled, and
the volume control in the CD drive set to maximum. This indicates the
connection is really not present.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Michael Karcher [Fri, 6 Apr 2012 13:34:17 +0000 (15:34 +0200)]
ALSA: hda - fix record volume controls of CX20459 ("Venice")
The "input converter" widget of the CX20459 has only one input amplifier,
expose that one as "Capture Volume/Capture Switch". The actual record
source selection is already exposed through the separately installed
input mux.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stephen Warren [Fri, 6 Apr 2012 05:11:16 +0000 (23:11 -0600)]
ASoC: tegra: fix i2s compilation when !CONFIG_DEBUG_FS
Commit d4a2eca "ASoC: Tegra I2S: Remove dependency on pdev->id" changed
the prototype of tegra_i2s_debug_add, but didn't update the dummy inline
used when !CONFIG_DEBUG_FS. Fix that.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: <stable@vger.kernel.org> # 3.3
Stephen Warren [Thu, 5 Apr 2012 18:28:01 +0000 (12:28 -0600)]
ASoC: set idle_bias_off=1 for all platform DAPM contexts
The ASoC core currently defaults to using STANDBY rather than OFF for
idle ASoC platform devices, which causes a permanent pm_runtime_get() on
them. This keeps the device active unnecessarily. This can be especially
problematic when the ASoC platform device and DAI device are the same
device.
The distinction between OFF and STANDBY is likely not relevant for ASoC
platform drivers, since they aren't analog devices. So, solve this issue
by hard-coding idle_bias_off = 1 for all ASoC platform devices. If this
turns out to be a problem, this value could be sourced from the
snd_soc_platform_driver, similarly to soc_probe_codec().
Note: Prior to this change, this caused a large (10) runtime_active count
for the Tegra I2S controller even when not in use, and a leak in that
value as streams were started and stopped. This change probably hides a
bug.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALSA: hda - Fix internal mic for Lenovo Ideapad U300s
The internal mic input is phase inverted on one channel.
To avoid people in userspace summing the channels together
and get zero result, use a separate mixer control for the
inverted channel.
BugLink: https://bugs.launchpad.net/bugs/903853 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the ssi port numbers in sysfs to fix this problem.
Reported-by: Joan Carles <joancarles@fqingenieria.es> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ak4642 out_tlv is +12.0dB to -115.0 dB, and it supports mute.
But current settings didn't care +1 step for mute.
This patch adds it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org
Mark Brown [Wed, 4 Apr 2012 11:06:24 +0000 (12:06 +0100)]
MAINTAINERS: Don't list everyone working on Wolfson drivers
Rather than listing every single person who works on the drivers include
the mailing list where they can all be found. Leave myself as a human
contact.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jarkko Nikula [Tue, 3 Apr 2012 06:45:43 +0000 (09:45 +0300)]
MAINTAINERS: Add missing ASoC OMAP co-maintainer
Peter Ujfalusi has been co-maintaining sound/soc/omap/ for years but
was missing from this MAINTAINERS entry.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Martin Jansa [Mon, 2 Apr 2012 08:24:08 +0000 (10:24 +0200)]
ASoC: pxa: pxa2xx-i2s: add io.h for IOMEM macro
* fixes
sound/soc/pxa/pxa2xx-i2s.c:86:2: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
sound/soc/pxa/pxa2xx-i2s.c:86:2: error: initializer element is not constant
after 23019a733bb83c8499f192fb428b7e6e81c95a34 removed IOMEM
definition from arch/arm/mach-pxa/include/mach/hardware.h
Signed-off-by: Martin Jansa <Martin.Jansa@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds [Sat, 31 Mar 2012 22:11:39 +0000 (15:11 -0700)]
Merge branch 's3-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio-console
Pull virtio S3 support patches from Amit Shah:
"Turns out S3 is not different from S4 for virtio devices: the device
is assumed to be reset, so the host and guest state are to be assumed
to be out of sync upon resume. We handle the S4 case with exactly the
same scenario, so just point the suspend/resume routines to the
freeze/restore ones.
Once that is done, we also use the PM API's macro to initialise the
sleep functions.
A couple of cleanups are included: there's no need for special thaw
processing in the balloon driver, so that's addressed in patches 1 and
2.
Testing: both S3 and S4 support have been tested using these patches
using a similar method used earlier during S4 patch development: a
guest is started with virtio-blk as the only disk, a virtio network
card, a virtio-serial port and a virtio balloon device. Ping from
guest to host, dd /dev/zero to a file on the disk, and IO from the
host on the virtio-serial port, all at once, while exercising S4 and
S3 (separately) were tested. They all continue to work fine after
resume. virtio balloon values too were tested by inflating and
deflating the balloon."
Pulling from Amit, since Rusty is off getting married (and presumably
shaving people).
* 's3-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio-console:
virtio-pci: switch to PM ops macro to initialise PM functions
virtio-pci: S3 support
virtio-pci: drop restore_common()
virtio: drop thaw PM operation
virtio: balloon: Allow stats update after restore from S4
Linus Torvalds [Sat, 31 Mar 2012 20:42:57 +0000 (13:42 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull second try at vfs part d#2 from Al Viro:
"Miklos' first series (with do_lookup() rewrite split into edible
chunks) + assorted bits and pieces.
The 'untangling of do_lookup()' series is is a splitup of what used to
be a monolithic patch from Miklos, so this series is basically "how do
I convince myself that his patch is correct (or find a hole in it)".
No holes found and I like the resulting cleanup, so in it went..."
Changes from try 1: Fix a boot problem with selinux, and commit messages
prettied up a bit.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (24 commits)
vfs: fix out-of-date dentry_unhash() comment
vfs: split __lookup_hash
untangling do_lookup() - take __lookup_hash()-calling case out of line.
untangling do_lookup() - switch to calling __lookup_hash()
untangling do_lookup() - merge d_alloc_and_lookup() callers
untangling do_lookup() - merge failure exits in !dentry case
untangling do_lookup() - massage !dentry case towards __lookup_hash()
untangling do_lookup() - get rid of need_reval in !dentry case
untangling do_lookup() - eliminate a loop.
untangling do_lookup() - expand the area under ->i_mutex
untangling do_lookup() - isolate !dentry stuff from the rest of it.
vfs: move MAY_EXEC check from __lookup_hash()
vfs: don't revalidate just looked up dentry
vfs: fix d_need_lookup/d_revalidate order in do_lookup
ext3: move headers to fs/ext3/
migrate ext2_fs.h guts to fs/ext2/ext2.h
new helper: ext2_image_size()
get rid of pointless includes of ext2_fs.h
ext2: No longer export ext2_fs.h to user space
mtdchar: kill persistently held vfsmount
...
Linus Torvalds [Sat, 31 Mar 2012 20:35:31 +0000 (13:35 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar.
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix incorrect usage of for_each_cpu_mask() in select_fallback_rq()
sched: Fix __schedule_bug() output when called from an interrupt
sched/arch: Introduce the finish_arch_post_lock_switch() scheduler callback
So, those who wish to specify raw events can now use the following
event format:
-e cpu/cmask=1,event=2,umask=3
Most people will not want to specify any events (let alone raw
events), they'll just use whatever default event the tools use.
But for more obscure PMU events that have no cross-architecture
generic events the above syntax is more usable and a bit more
structured than specifying hex numbers."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
perf tools: Remove auto-generated bison/flex files
perf annotate: Fix off by one symbol hist size allocation and hit accounting
perf tools: Add missing ref-cycles event back to event parser
perf annotate: addr2line wants addresses in same format as objdump
perf probe: Finder fails to resolve function name to address
tracing: Fix ent_size in trace output
perf symbols: Handle NULL dso in dso__name_len
perf symbols: Do not include libgen.h
perf tools: Fix bug in raw sample parsing
perf tools: Fix display of first level of callchains
perf tools: Switch module.h into export.h
perf: Move mmap page data_head offset assertion out of header
perf: Fix mmap_page capabilities and docs
perf diff: Fix to work with new hists design
perf tools: Fix modifier to be applied on correct events
perf tools: Fix various casting issues for 32 bits
perf tools: Simplify event_read_id exit path
tracing: Fix ftrace stack trace entries
tracing: Move the tracing_on/off() declarations into CONFIG_TRACING
perf report: Add a simple GTK2-based 'perf report' browser
...
Linus Torvalds [Sat, 31 Mar 2012 20:32:30 +0000 (13:32 -0700)]
Merge tag 'parisc-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull PARISC misc updates from James Bottomley:
"This is a couple of minor updates (fixing lws futex locking and
removing some obsolete cpu_*_map calls)."
* tag 'parisc-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] remove references to cpu_*_map.
[PARISC] futex: Use same lock set as lws calls
Linus Torvalds [Sat, 31 Mar 2012 20:31:23 +0000 (13:31 -0700)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
Al Viro [Fri, 30 Mar 2012 18:18:50 +0000 (14:18 -0400)]
untangling do_lookup() - get rid of need_reval in !dentry case
Everything arriving into if (!dentry) will have need_reval = 1.
Indeed, the only way to get there with need_reval reset to 0 would
be via
if (unlikely(d_need_lookup(dentry)))
goto unlazy;
if (unlikely(dentry->d_flags & DCACHE_OP_REVALIDATE)) {
status = d_revalidate(dentry, nd);
if (unlikely(status <= 0)) {
if (status != -ECHILD)
need_reval = 0;
goto unlazy;
...
unlazy:
/* no assignments to dentry */
if (dentry && unlikely(d_need_lookup(dentry))) {
dput(dentry);
dentry = NULL;
}
and if d_need_lookup() had already been false the first time around, it
will remain false on the second call as well.
Al Viro [Fri, 30 Mar 2012 18:13:15 +0000 (14:13 -0400)]
untangling do_lookup() - eliminate a loop.
d_lookup() *will* fail after successful d_invalidate(), if we are
holding i_mutex all along. IOW, we don't need to jump back to
l: - we know what path will be taken there and can do that (i.e.
d_alloc_and_lookup()) directly.
Al Viro [Fri, 30 Mar 2012 18:04:16 +0000 (14:04 -0400)]
untangling do_lookup() - isolate !dentry stuff from the rest of it.
Duplicate the revalidation-related parts into if (!dentry) branch.
Next step will be to pull them under i_mutex.
This and the next 8 commits are more or less a splitup of patch
by Miklos; folks, when you are working with something that convoluted,
carve your patches up into easily reviewed steps, especially when
a lot of codepaths involved are rarely hit...
projects / ~shefty / rdma-dev.git / log