[S390] smsgiucv_app: deliver z/VM CP special messages (SMSG) as uevents
The smsgiucv_app driver registers a callback with the smsgiucv driver
to receive z/VM CP special messages (SMSG) starting with "APP".
When the callback is called for special messages, the driver creates
an uevent for the received message. The uevent consists of additional
environment data containing the message prefix ("APP"), message sender,
and message content.
udev rules can be used to trigger application specific actions through
matching the content or sender of the special message.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[S390] dasd: automatic recognition of read-only devices
In z/VM it is possible to attach a device as read-only. To prevent
unintentional write requests and subsequent I/O errors, we can detect
this configuration using the z/VM DIAG 210 interface and set the
respective linux block device to read-only as well.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ursula Braun [Mon, 8 Mar 2010 11:25:20 +0000 (12:25 +0100)]
[S390] remove unused qdio flags in zfcp and qeth
zfcp and qeth are setting flags for the qdio-layer, but these flags
are not used in qdio. Patch removes the flag definitions from qdio
and their settings in zfcp and qeth.
Cc: Jan Glauber <jang@linux.vnet.ibm.com> Cc: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio-console:
virtio: console: Use better variable names for fill_queue operation
virtio: console: Fix type of 'len' as unsigned int
Linus Torvalds [Sun, 7 Mar 2010 23:56:25 +0000 (15:56 -0800)]
Merge branch 'for-linus/i2c' of git://git.fluff.org/bjdooks/linux
* 'for-linus/i2c' of git://git.fluff.org/bjdooks/linux:
i2c: Add support for Xilinx XPS IIC Bus Interface
i2c: omap: Add support for 16-bit registers
i2c-pnx: fix setting start/stop condition
powerpc: doc/dts-bindings: update doc of FSL I2C bindings
i2c-mpc: add support for the MPC512x processors from Freescale
i2c-mpc: rename "setclock" initialization functions to "setup"
i2c-mpc: use __devinit[data] for initialization functions and data
i2c/imx: don't add probe function to the driver struct
i2c: Add support for Ux500/Nomadik I2C controller
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: Convert sh to use read/update_persistent_clock
sh: Move PMB debugfs entry initialization to later stage
sh: Fix up flush_cache_vmap() on SMP.
sh: fix up MMU reset with variable PMB mapping sizes.
sh: establish PMB mappings for NUMA nodes.
sh: check for existing mappings for bolted PMB entries.
sh: fixed virt/phys mapping helpers for PMB.
sh: make pmb iomapping configurable.
sh: reworked dynamic PMB mapping.
sh: Fix up cpumask_of_pcibus() for the NUMA build.
serial: sh-sci: Tidy up build warnings.
sh: Fix up ctrl_read/write stragglers in migor setup.
serial: sh-sci: Add DMA support.
dmaengine: shdma: extend .device_terminate_all() to record partial transfer
sh: merge sh7722 and sh7724 DMA register definitions
sh: activate runtime PM for dmaengine on sh7722 and sh7724
dmaengine: shdma: add runtime PM support.
dmaengine: shdma: separate DMA headers.
dmaengine: shdma: convert to platform device resources
dmaengine: shdma: fix DMA error handling.
...
Linus Torvalds [Sun, 7 Mar 2010 23:45:53 +0000 (15:45 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: use __ratelimit in unaligned.c
parisc: Convert to read/update_persistent_clock
parisc: Simplify param.h by including <asm-generic/param.h>
parisc: drop unnecessary cast in __ldcw_align() macro
parisc: add strict copy size checks (v2)
parisc: remove trailing space in messages
parisc: ditto sys_accept4
parisc: wire up sys_recvmmsg
Linus Torvalds [Sun, 7 Mar 2010 23:45:35 +0000 (15:45 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Provide generic subsystem-level callbacks
PM / Runtime: Document power.runtime_auto and related functions
Cory Maccarrone [Sun, 13 Dec 2009 01:54:02 +0000 (17:54 -0800)]
i2c: omap: Add support for 16-bit registers
The current i2c-omap driver is set up for 32-bit registers, which
corresponds to most OMAP devices. However, OMAP730/850 based
devices use a 16-bit register size.
This change modifies the driver to perform a runtime CPU type check
to determine the register sizes, and uses a bit shift of either 1
or 2 bits to compute the proper register sizes for all registers.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Luotao Fu [Mon, 1 Mar 2010 12:24:24 +0000 (13:24 +0100)]
i2c-pnx: fix setting start/stop condition
The start/stop condtions are set in different places repetedly in the i2c-pnx
driver. Beside in i2c_pnx_start and i2c_pnx_stop the start/stop bit are also
set during the transfer of a i2c message in the master_xmit/rcv calls. This is
wrong since we can't set the start/stop condition during the transaction of a
single message any way. As a matter of fact, the driver will sometimes set both
the start and the stop bits at one time. This can be easily reproduced by
sending a simple read request like e.g
struct i2c_msg msgs[] = {
{ addr, 0, 1, buf },
{ addr, I2C_M_RD, offset, buf }
};
While processing the first message the i2c_pnx_master_xmit will set both the
start_bit and the stop_bit, which will eventually confuse the slave.
Fixed by remove setting start/stop condition from the transmit routines.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
powerpc: doc/dts-bindings: update doc of FSL I2C bindings
This patch adds the MPC5121 to the list of supported devices,
enhances the doc of the "clock-frequency" property and removes
the obsolete "cell-index", "device_type" and "fsl-i2c" property.
Furthermore an example for the MPC5121 has been added.
Signed-off-by: Wolfgang Grandegger <wg@denx.de> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
i2c-mpc: add support for the MPC512x processors from Freescale
As I2C interrupts must be enabled for the MPC512x by the setup function
as well, "fsl,preserve-clocking" is handled in a slighly different way.
Also, the old settings are now reported calling dev_dbg(). For the
MPC512x the clock setup function of the MPC52xx can be re-used.
Furthermore, the Kconfig help has been updated and corrected.
Signed-off-by: Wolfgang Grandegger <wg@denx.de> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
i2c-mpc: rename "setclock" initialization functions to "setup"
To prepare support for the MPC512x processors from Freescale the
"setclock" initialization functions have been renamed to "setup"
because I2C interrupts must be enabled for the MPC512x by this
function as well.
Signed-off-by: Wolfgang Grandegger <wg@denx.de> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
i2c-mpc: use __devinit[data] for initialization functions and data
"__devinit[data]" has not yet been used for all initialization functions
and data. To avoid truncating lines, the struct "mpc_i2c_match_data" has
been renamed to "mpc_i2c_data", which is even the better name.
Signed-off-by: Wolfgang Grandegger <wg@denx.de> Tested-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
i2c/imx: don't add probe function to the driver struct
Having a pointer to the probe function is unnecessary when using
platform_driver_probe and yields a section mismatch warning after
removing the white list entry "*driver" for
{ .data$, .data.rel$ } -> { .init.* } mismatches in modpost.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Randy Dunlap [Fri, 5 Mar 2010 17:43:06 +0000 (09:43 -0800)]
mfd: Fix lpc_sch related depends/selects, fix build error
LPC_SCH is selected by GPI_SCH and I2C_ISCH, even when PCI is not
enabled, but LPC_SCH depends on PCI, so make GPI_SCH and I2C_ISCH
also depend on PCI.
Those 2 selects also need to select what LPC_SCH selects,
since kconfig does not follow selects.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Denis Turischev <denis@compulab.co.il> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Tue, 23 Feb 2010 11:08:06 +0000 (11:08 +0000)]
mfd: Use completion interrupt for WM831x AUXADC
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the status of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM831x interrupt infrastructure hooked
up.
Also reduce the timeout for completion of conversions to 5ms from
the previous 10ms, the lower timeout should be sufficient.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Tue, 23 Feb 2010 11:08:05 +0000 (11:08 +0000)]
mfd: Use completion interrupt for WM835x AUXADC
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the state of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM8350 interrupt infrastructure hooked
up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mike Turquette [Mon, 22 Feb 2010 17:16:30 +0000 (11:16 -0600)]
mfd: Introduce remove_script function for twl4030
New function twl4030_remove_script(u8 flags) takes a script type as
defined in twl.h and prevents any script already loaded in that position
from running. This is accomplished by programming SEQ_ADD_* to 0x3f,
the END_OF_SCRIPT value, where SEQ_ADD_* is determined by flags.
(Future) users of this function include OMAP board files for machines
facing a race condition between sleep and warm reset.
Signed-off-by: Mike Turquette <mturquette@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Wed, 17 Feb 2010 18:45:26 +0000 (18:45 +0000)]
gpiolib: Force wm831x GPIOs into GPIO mode when requested
This is the chip default but it's possible the bootloader or OTP
will have been configured to a different mode (eg, to provide
feedback during startup).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Wed, 17 Feb 2010 18:45:25 +0000 (18:45 +0000)]
mfd: Add WM831x revision B support
Revision B of the WM831x devices changes the sense of the tristate
bit for GPIO configuration, inverting it to become an enable instead.
Take account of this in the gpiolib driver.
A current sink regulation status bit has also been added in revision B,
add a flag indicating if it's present but don't use it yet.
This revision also adds an interrupt on key up for the ON pin event
which the existing code is able to take advantage of.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Magnus Damm [Wed, 17 Feb 2010 07:38:14 +0000 (16:38 +0900)]
tmio_mmc: Remove const from platform data V3
Remove const from the tmio-mmc platform data hclk V3.
This change makes it possible to remove the type cast
from the sh_mobile_sdhi driver which is using the clock
framework to get the clock rate.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Magnus Damm [Wed, 17 Feb 2010 07:38:04 +0000 (16:38 +0900)]
tmio_mmc: Use 100ms mmc_detect_change() delay
This patch changes the tmio_mmc driver to wait 100ms
before checking the card detect status. This type of
delay is quite common among mmc drivers, it seems that
most hardware platforms need to give the hardware some
time to settle before checking card availabilty.
Hotplug is half-broken without this patch on the sh7724
Ecovec board. Hot insertion seems ok but eject is never
detected without this patch.
Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Yusuke Goda [Wed, 17 Feb 2010 07:37:55 +0000 (16:37 +0900)]
tmio_mmc: Add MMC_CAP_MMC_HIGHSPEED support V2
Enable MMC_CAP_XX support in the tmio_mmc driver if
pdata->capabilities is set.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com> Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On SuperH platforms the SDHI controller does not produce any command IRQs after
a completed IO. This leads to card-detect interrupts staying disabled. Do not
disable card-detect interrupts on DATA IRQs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch disables TWL4030/5030 I2C1 adn I2C4(SR) internal pull-up, to
use only the external HW resistor >=470 Ohm for the assured
functionality in HS mode.
While testing the I2C in High Speed mode, it was discovered that
without a proper pull-up resistor, there is data corruption during
multi-byte transfer. RTC(time_set) test case was used for testing.
From the analysis done, it was concluded that ideally we need a
pull-up of 1.6k Ohm(recomended) or atleast 470 Ohm or greater for
assured performance in HS mode.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com> Signed-off-by: Allen Pais <allen.pais@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Denis Turischev [Fri, 19 Feb 2010 10:26:25 +0000 (11:26 +0100)]
mfd: Introduce lpc_sch for Intel SCH LPC bridge
Intel Poulsbo (SCH) chipset LPC bridge controller contains several
functions. Creating and MFD driver for the LPC bridge controller allows
simultaneous use of SMBus and GPIO interfaces on the SCH.
Signed-off-by: Denis Turischev <denis@compulab.co.il> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Haojian Zhuang [Mon, 8 Feb 2010 10:02:00 +0000 (05:02 -0500)]
mfd: Use genirq in 88pm860x
Use genirq to simplify IRQ handling in 88pm860x. Remove the interface of
mask/free IRQs on 88pm860x. All these work is taken by genirq. Update the
touchscreen driver of 88pm860x since IRQ handling is changed.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Joonyoung Shim [Sun, 7 Feb 2010 01:16:14 +0000 (10:16 +0900)]
mfd: Fix WM8994 error handling
This patch fixes wrong goto statement for error handling on probe.
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Haojian Zhuang [Fri, 5 Feb 2010 15:07:54 +0000 (16:07 +0100)]
mfd: Update irq handler in max8925
Update thread irq handler. Simply the interface of using thread irq.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Fri, 29 Jan 2010 18:20:29 +0000 (18:20 +0000)]
mfd: Add initial WM8994 support
The WM8994 is a highly integrated ultra low power audio hub CODEC.
Since it includes on-board regulators and GPIOs it is represented
as a multi-function device, though the overwhelming majority of
the functionality is provided by the ASoC CODEC driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Randy Dunlap [Thu, 21 Jan 2010 03:55:34 +0000 (19:55 -0800)]
mfd: htc-i2cpld depends on GPIOLIB
htc-i2cpld should depend on GPIOLIB, otherwise there are many
build errors:
drivers/mfd/htc-i2cpld.c:50: error: field 'chip_out' has incomplete type
drivers/mfd/htc-i2cpld.c:54: error: field 'chip_in' has incomplete type
drivers/mfd/htc-i2cpld.c:243: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:243: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:278: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:278: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:282: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:282: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:315: error: dereferencing pointer to incomplete type
drivers/mfd/htc-i2cpld.c:322: warning: type defaults to 'int' in declaration of '__mptr'
drivers/mfd/htc-i2cpld.c:322: warning: initialization from incompatible pointer type
drivers/mfd/htc-i2cpld.c:467+: error: dereferencing pointer to incomplete type [19X]
drivers/mfd/htc-i2cpld.c:490: error: implicit declaration of function 'gpiochip_add'
drivers/mfd/htc-i2cpld.c:504: error: implicit declaration of function 'gpiochip_remove'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christoph Egger [Fri, 15 Jan 2010 14:33:46 +0000 (15:33 +0100)]
mfd: Remove leftover from discontinued TWL4030 battery patch
The TWL4030_BCI_BATTERY config option originates from a patch to the
omap git tree. However inclusion in linux was seemingly rejected and
the functionality nears inclusion under a different name so this
removes the bits of the old version that made it into the mainline
kernel again.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Linus Walleij [Sun, 17 Jan 2010 19:57:43 +0000 (20:57 +0100)]
mfd: Fix debugfs code in AB3100 OTP driver
This fixes the aged and unreachable debugfs code in the AB3100
OTP driver so that it's (A) reachable and (B) works. Bug detected
in parallell by Christoph Egger using VAMOS and Robert P. J. Day
by his kernel scanning script.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Cc: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Cc: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Linus Walleij [Tue, 19 Jan 2010 10:41:52 +0000 (11:41 +0100)]
mfd: Use AB3100 MFD core IRQ for interrupt randomness
This reintroduces the entropy sampling of the AB3100 IRQ as the
IRQF_SAMPLE_RANDOM is going out according to the feature removal
schedule. I'm trying to do this the right way then, so CC:ing some
random people for a quick review. We add entropy for interrupt
events in the AB3100 which are truly random in nature, like
external cables being connected, voltages on batteries dropping
below certain ranges, ADC triggers or overheating.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Cc: Robin Getz <rgetz@blackfin.uclinux.org> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cory Maccarrone [Tue, 19 Jan 2010 10:22:45 +0000 (11:22 +0100)]
mfd: Add HTCPLD driver
This change introduces a driver for the HTC PLD chip found
on some smartphones, such as the HTC Wizard and HTC Herald.
It works through the I2C bus and acts as a GPIO extender.
Specifically:
* it can have several sub-devices, each with its own I2C
address
* Each sub-device provides 8 output and 8 input pins
* The chip attaches to one GPIO to signal when any of the
input GPIOs change -- at which point all chips must be
scanned for changes
This driver implements the GPIOs throught the kernel's
GPIO and IRQ framework. This allows any GPIO-servicing
drivers to operate on htcpld pins, such as the gpio-keys
and gpio-leds drivers.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Haojian Zhuang [Mon, 11 Jan 2010 12:10:08 +0000 (13:10 +0100)]
regulator: Add max8925 support
MAX8925 contains 3 Buck and 20 LDO regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Haojian Zhuang [Fri, 8 Jan 2010 11:01:24 +0000 (06:01 -0500)]
mfd: Support 88pm8606 in 860x driver
88PM8606 and 88PM8607 are two discrete chips used for power management.
Hardware designer can use them together or only one of them according to
requirement.
There's some logic tightly linked between these two chips. For example, USB
charger driver needs to access both chips by I2C interface.
Now share one driver to these two devices. Only one I2C client is identified
in platform init data. If another chip is also used, user should mark it in
companion_addr field of platform init data. Then driver could create another
I2C client for the companion chip.
All I2C operations are accessed by 860x-i2c driver. In order to support both
I2C client address, the read/write API is changed in below.
Linus Walleij [Fri, 8 Jan 2010 09:44:16 +0000 (10:44 +0100)]
mfd: Convert AB3100 driver to threaded IRQ
This converts the AB3100 core MFD driver to use a threaded
interrupt handler instead of the explicit top/bottom-half
construction with a workqueue. This saves some code and make it
more similar to other modern MFD drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Wed, 6 Jan 2010 19:24:25 +0000 (19:24 +0000)]
mfd: Update WM8350 drivers for changed interrupt numbers
The headphone detect and charger are using the IRQ numbers so need
to take account of irq_base with the genirq conversion. I obviously
picked the wrong system for initial testing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Tue, 5 Jan 2010 20:40:47 +0000 (20:40 +0000)]
mfd: Don't allow WM8350 to be built modular
The genirq implementation does not allow modules to implement irq_chips
so the conversion of WM8350 to genirq means we can no longer allow the
driver to be built as a module.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Tue, 5 Jan 2010 13:59:09 +0000 (13:59 +0000)]
mfd: Convert WM8350 to genirq
This gives us use of the diagnostic facilities genirq provides and
will allow implementation of interrupt support for the WM8350 GPIOs.
Stub functions are provided to ease the transition of the individual
drivers, probably after additional work to pass the IRQ numbers via
the struct devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Tue, 5 Jan 2010 13:59:08 +0000 (13:59 +0000)]
rtc: Suppress duplicate enable/disable of WM8350 update interrupt
Unlike the wm8350-custom code genirq nests enable and disable calls
so we can't just unconditionally mask or unmask the interrupt,
we need to remember the state we set and only mask or unmask when
there is a real change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Cc: rtc-linux@googlegroups.com Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Julia Lawall [Tue, 22 Dec 2009 20:31:43 +0000 (21:31 +0100)]
mfd: Correct use after free for t7l66xb
The structure t7l66xb should not be freed before the subsequent references
to its fields in the arguments to clk_put. Furthermore, this structure is
allocated near the beginning of the function, and a goto to the label
err_noirq appears after a successful allocation, so it would seem that the
kfree should be moved down below this label.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Ian Molton <ian@mnementh.co.uk> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The requested memory region is smaller than the actual ioremap().
Use resource_size() to get the correct size.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>