Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 23 Dec 2009 13:21:46 +0000 (13:21 +0000)]
igb: check both function bits in status register in wol exception
The ethtool code for enabling Wake on Lan was not correctly checking the
status register bits so as a result ports 0 and 2 were both being allowed
to set WOL to enabled even though it is only supported on the first port
for our adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 23 Dec 2009 13:21:27 +0000 (13:21 +0000)]
igb: correctly offset 82575 flow control watermarks by 16 bytes
The watermark values for the 82575 were not being set correctly. As a
result the high and low watermark values were set to the same value which
can lead to excess xon/xoff packets being generated.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 23 Dec 2009 13:21:07 +0000 (13:21 +0000)]
igb: do not force retry count to 1 on 82580 phy
This change resolves an issue seen in some configurations where the link
may drop to 100Mb/s even though the link itself supports 1000Mb/s. The
issue was root caused to the fact that we were only trying the link once.
Now instead we will try up to 5 attempts on a faulty cable before
downshifting to 100Mb/s.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 23 Dec 2009 13:20:47 +0000 (13:20 +0000)]
igb: do not force pcs link when in KX mode
We were forcing the PCS link up in error when we are in KX mode. We should
only be disabling autoneg, not forcing the link up.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Slattery [Wed, 23 Dec 2009 13:48:32 +0000 (13:48 +0000)]
sfc: QT2025C: Work around PHY firmware initialisation bug
The PHY's firmware very occasionally appears to lock up very early, but
with the heartbeat update still running. Rebooting the microcontroller
core seems to be sufficient to recover.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Slattery [Wed, 23 Dec 2009 13:48:04 +0000 (13:48 +0000)]
sfc: QT2025C: Switch into self-configure mode when not in loopback
The PHY boots in a mode which is not necessarily optimal. This change
switches it to self-configure mode (except when in loopback, which
won't work in that mode if an SFP+ module is not present) by rebooting
the PHY's microcontroller, and replicating the sequence of configuration
writes from the boot EEPROM with the appropriate changes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matthew Slattery [Wed, 23 Dec 2009 13:47:37 +0000 (13:47 +0000)]
sfc: QT2025C: Work around PHY bug
If we see the PHY remaining stuck in a link-down state due to PCS being
down while PMA/PMD is up, we briefly switch to PMA/PMD loopback and back,
which usually unsticks it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 23 Dec 2009 13:46:47 +0000 (13:46 +0000)]
sfc: Include XGXS in XMAC link status check except in XGMII loopback
The XGXS block may not get a link immediately in XGXS or XAUI loopback
modes, so we still need to check it. Split falcon_xaui_link_ok() into
falcon_xgxs_link_ok(), which checks only the Falcon XGXS block, and
falcon_xmac_link_ok(), which checks one or both sides of the link as
appropriate. Also rename falcon_check_xaui_link() to
falcon_xmac_link_ok_retry().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Hodgson [Wed, 23 Dec 2009 13:46:36 +0000 (13:46 +0000)]
sfc: Move PHY software state initialisation from init() into probe()
This prevents efx->link_advertising from being blatted during
a reset.
The phy_short_reach sysfs node is now destroyed later in the
port shutdown process, so check for STATE_RUNNING after
acquiring the rtnl_lock (just like in set_phy_flash_cfg).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ps3_gelic_wireless: Fix build failure due to missing WEXT_PRIV
The option to support the old style PSK interface in the PS3
GELIC wireless drivers requires CONFIG_WEXT_PRIV to be set
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: rework MLME for multiple authentications
inadvertedly broke WMM because it removed, along with
a bunch of other now useless initialisations, the line
initialising sdata->u.mgd.wmm_last_param_set to -1
which would make it adopt any WMM parameter set. If,
as is usually the case, the AP uses WMM parameter set
sequence number zero, we'd never update it until the
AP changes the sequence number.
Add the missing initialisation back to get the WMM
settings from the AP applied locally.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org [2.6.31+] Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 17 Dec 2009 12:55:48 +0000 (13:55 +0100)]
mac80211: fix peer HT capabilities
I noticed yesterday, because Jeff had noticed
a speed regression, cf. bug
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2138
that the SM PS settings for peers were wrong.
Instead of overwriting the SM PS settings with
the local bits, we need to keep the remote bits.
The bug was part of the original HT code from
over two years ago, but unfortunately nobody
noticed that it makes no sense -- we shouldn't
be overwriting the peer's setting with our own
but rather keep it intact when masking the peer
capabilities with our own.
While fixing that, I noticed that the masking of
capabilities is completely useless for most of
the bits, so also fix those other bits.
Finally, I also noticed that PSMP_SUPPORT no
longer exists in the final 802.11n version, so
also remove that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roel Kluin [Wed, 16 Dec 2009 16:01:38 +0000 (17:01 +0100)]
iwmc3200wifi: Fix test of unsigned in iwm_ntf_stop_resume_tx()
`queue' was unsigned so the test did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Reviewed-by: Pavel Roskin <proski@gnu.org> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl-tx.c: In function `iwl_hw_txq_ctx_free':
drivers/net/wireless/iwlwifi/iwl-tx.c:410: warning: suggest explicit braces to avoid ambiguous `else'
Cc: Zhu Yi <yi.zhu@intel.com> Cc: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Mon, 14 Dec 2009 11:04:56 +0000 (16:34 +0530)]
ath9k: Stop ANI when doing a reset
The MIB counters are disabled when doing a chip reset.
Since ANI depends on the MIB registers for its operation, relying
on the contents of said registers during HW reset results in sub-optimal
performance.
Cc: stable@kernel.org Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Mon, 14 Dec 2009 09:27:08 +0000 (14:57 +0530)]
ath9k: Fix TX queue draining
When TX DMA termination has failed, the HW has to be reset
completely. Doing a fast channel change in this case is insufficient.
Also, change the debug level of a couple of messages to FATAL.
Cc: stable@kernel.org Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Fix calculation of rt2800 iveiv entry offset.
Fix typo. The index should be multiplied by the entry size, not 'and'-ed.
Found via code-inspection.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Mon, 14 Dec 2009 22:12:11 +0000 (14:12 -0800)]
iwlwifi: initialize spinlock before use
Recent powersaving work resulted in power management ops being called
during EEPROM initialization. The lock used by these functions is not
initialized at this time. Ensure lock is initialized before it is used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Mon, 14 Dec 2009 22:12:10 +0000 (14:12 -0800)]
iwl3945: disable power save
we see from http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2125
that power saving does not work well on 3945. Since then power saving has
also been connected with association problems where an AP deathenticates a
3945 after it is unable to transmit data to it - this happens when 3945
enters power savings mode.
Disable power save support until issues are resolved.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> CC: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 14 Dec 2009 22:12:09 +0000 (14:12 -0800)]
iwlwifi: fix more eeprom endian bugs
I've also for a long time had a problem with the
temperature calculation code, which I had fixed
by byte-swapping the values, and now it turns out
that was the correct fix after all.
Also, any use of iwl_eeprom_query_addr() that is
for more than a u8 must be cast to little endian,
and some structs as well.
Fix all this. Again, no real impact on platforms
that already are little endian.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 14 Dec 2009 22:12:08 +0000 (14:12 -0800)]
iwlwifi: fix EEPROM/OTP reading endian annotations and a bug
The construct "le16_to_cpu((__force __le16)(r >> 16))" has
always bothered me when looking through the iwlwifi code,
it shouldn't be necessary to __force anything, and before
this code, "r" was obtained with an ioread32, which swaps
each of the two u16 values in it properly when swapping the
entire u32 value. I've had arguments about this code with
people before, but always conceded they were right because
removing it only made things not work at all on big endian
platforms.
However, analysing a failure of the OTP reading code, I now
finally figured out what is going on, and why my intuition
about that code being wrong was right all along.
It turns out that the 'priv->eeprom' u8 array really wants
to have the data in it in little endian. So the force code
above and all really converts *to* little endian, not from
it. Cf., for instance, the function iwl_eeprom_query16() --
it reads two u8 values and combines them into a u16, in a
little-endian way. And considering it more, it makes sense
to have the eeprom array as on the device, after all not
all values really are 16-bit values, the MAC address for
instance is not.
Now, what this really means is that all the annotations are
completely wrong. The eeprom reading code should fill the
priv->eeprom array as a __le16 array, with __le16 values.
This also means that iwl_read_otp_word() should really have
a __le16 pointer as the data argument, since it should be
filling that in a format suitable for priv->eeprom.
Propagating these changes throughout, iwl_find_otp_image()
is found to be, now obviously visible, defective -- it uses
the data returned by iwl_read_otp_word() directly as if it
was CPU endianness. Fixing that, which is this hunk of the
patch:
is the only real change of this patch. Everything else is
just fixing the sparse annotations.
Also, the bug only shows up on big endian platforms with a
1000 series card. 5000 and previous series do not use OTP,
and 6000 series has shadow RAM support which means we don't
ever use the defective code on any cards but 1000.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Disable powersaving for rt61pci and rt2800pci.
We've had many reports of rt61pci failures with powersaving enabled.
Therefore, as a stop-gap measure, disable powersaving of the rt61pci
until we have found a proper solution.
Also disable powersaving on rt2800pci as it most probably will show
the same problem.
Cc: stable@kernel.org Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Sun, 13 Dec 2009 16:07:45 +0000 (17:07 +0100)]
drivers/net/wireless: Correct code taking the size of a pointer
sizeof(iv16) and sizeof(iv32) are the sizes of pointers. Change them to
the size of the copied data.
Furthermore, iveiv_entry is a local structure that has just been
initialized and is not visible outside this function. Thus, there would
seem to be no point to copy data into it. The order of the arguments is
thus changed to copy the data into the parameters, which are provided as
pointers, suggesting in this case that they should be used to return values.
A simplified version of the semantic patch that finds the first problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
First, we copy/paste the padding stuff from ath9k_tx to ath_tx_cabq since it
needs to same kind of padding, but for internally generated beacons.
Next, software padding done on TX needs to be removed before calling
ieee80211_tx_status. The code was already there in ath_tx_complete but it
was wrong. Fix it by using ath9k_cmn_padpos. This later code has been
tested by sending packets to a monitor interface and reading packets from the
same interface.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 10 Dec 2009 22:37:23 +0000 (14:37 -0800)]
iwlwifi: fix syslog message for event log dump size
When trigger event log dumping from debugfs, the entire event log
should be dumped and the size should match the number of events being
dump.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Thu, 10 Dec 2009 22:37:22 +0000 (14:37 -0800)]
iwlwifi: power up all devices for EEPROM read
Recent commits "iwlwifi: remove power-wasting calls to apm_ops.init()" and
"iwlagn: power up device before initializing EEPROM" had the goal of
reducing device power consumption from the time the module is loaded until
the interface is brought up and the device's power saving mechanisms kick
in. The idea is that once the module is loaded there is no need for the
device to consume power until the interface is brought up.
With the current solution the device is only powered up during EEPROM read,
and then so also only if the EEPROM type is OTP. We have found that on
certain platforms even non-OTP devices require power to be up during EEPROM
read. On these platforms the driver never loads and the system log contains
the following:
iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080403D8
We thus now power up all devices during EEPROM read.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Thu, 10 Dec 2009 22:37:21 +0000 (14:37 -0800)]
iwlwifi: allocated rx page accounting cleanup
In iwlwifi, priv->alloc_rxb_page is used to keep track of the Rx
pages allocated by the driver. This cleans up the page free routines
by introducing __iwl_free_pages/iwl_free_pages so that the accounting
is more accurate and less error prone. This also fixes two instances where
the counter was not updated.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sandeep Gopalpet [Wed, 16 Dec 2009 01:15:07 +0000 (01:15 +0000)]
gianfar: Fix stats support
This patch updates the per rx/tx queue stats.
To update the per rx queue stats a new structure has been
introduced rx_q_stats.
The per tx queue stats are updated via the netdev_queue
structure itself.
Note that we update only the tx_packtes, tx_bytes, rx_packets,
rx_bytes and rx_dropped stats on a per queue basis.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sandeep Gopalpet [Wed, 16 Dec 2009 01:14:58 +0000 (01:14 +0000)]
gianfar: Fix a filer bug
We need to enable filer whenever we need to use multiple RX
queues. Also, need to program RIR0 register with the required
distribution we require, if using RX filer hashing support for
packet distribution to multiple queues.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Sat, 19 Dec 2009 04:35:34 +0000 (20:35 -0800)]
bnx2: fixing a timout error due not refreshing TX timers correctly
When running the following script on an active bnx2 interface:
while(true); do ifconfig ethX mtu 9000; ifconfig ethX mtu 1500; done
A timeout error appears and dumps the following stack:
NETDEV WATCHDOG: eth4 (bnx2): transmit queue 0 timed out
------------[ cut here ]------------
Badness at net/sched/sch_generic.c:261
<snip>
This patch just fixes the way that ->trans_start is refreshed.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
can/at91: don't check platform_get_irq's return value against zero
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use (int)irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Sat, 19 Dec 2009 04:29:04 +0000 (20:29 -0800)]
bnx2: reset_task is crashing the kernel. Fixing it.
If bnx2 schedules a reset via the reset_task, e.g., due to a TX
timeout, it's possible for the NIC to be disabled with packets
pending for transmit. In this case, napi_disable will loop forever,
eventually crashing the kernel. This patch moves the disable of
the device to after the napi_disable call.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Hongyang [Sat, 19 Dec 2009 04:25:13 +0000 (20:25 -0800)]
ipv6: fix an oops when force unload ipv6 module
When I do an ipv6 module force unload,I got the following oops:
#rmmod -f ipv6
------------[ cut here ]------------
kernel BUG at mm/slub.c:2969!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:11.0/0000:02:03.0/net/eth2/ifindex
Modules linked in: ipv6(-) dm_multipath uinput ppdev tpm_tis tpm tpm_bios pcspkr pcnet32 mii parport_pc i2c_piix4 parport i2c_core floppy mptspi mptscsih mptbase scsi_transport_spi
It's because in ip6_frags_ns_sysctl_register,
"table" only alloced when "net" is not equals
to "init_net".So when we free "table" in
ip6_frags_ns_sysctl_unregister,we should check
this first.
This patch fix the problem.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
TI DaVinci EMAC: Fix MDIO bus frequency configuration
There was a typo in "if condition" checking for validity of MDIO
bus frequency passed as part of platform data. Bitwise AND was
being used instead of a Logical AND.
Tested on: DM6467 EVM
Signed-off-by: Nageswari Srinivasan <nageswari@ti.com> Acked-by: Anant Gole <anantgole@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Oksanen [Sat, 19 Dec 2009 04:18:21 +0000 (20:18 -0800)]
e100: Fix broken cbs accounting due to missing memset.
Alan Stern noticed that e100 caused slab corruption.
commit 98468efddb101f8a29af974101c17ba513b07be1 changed
the allocation of cbs to use dma pools that don't return zeroed memory,
especially the cb->status field used to track which cb to clean, causing
(the visible) double freeing of skbs and a wrong free cbs count.
Now the cbs are explicitly zeroed at allocation time.
Reported-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Roger Oksanen <roger.oksanen@cs.helsinki.fi> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruce Allan [Sat, 19 Dec 2009 04:14:59 +0000 (20:14 -0800)]
e1000e: LED settings in EEPROM ignored on 82571 and 82572
Do not override the customizable LED configuration set in the EEPROM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Netxen driver is doing this bogus thing to create a control file.
This fails if device doesn't exist, and overall is a bad way to do
the module parameter. Rather than fix borked code, just rewrite.
Just using a writeable module parameter of 0/1 is the correct way
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
RemoteBusy flag need to be unset before l2cap_ertm_send(), otherwise
l2cap_ertm_send() will return without sending packets because it checks
that flag before start sending.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ixgbe: allow tx of pre-formatted vlan tagged packets
When the 82598 is fed 802.1q packets, it chokes with
an error of the form:
ixgbe: eth0: ixgbe_tx_csum: partial checksum but proto=81!
As the logic there was not smart enough to look into
the vlan header to pick out the encapsulated protocol.
There are times when we'd like to send these packets
out without having to configure a vlan on the interface.
Here we check for the vlan tag and allow the packet to
go out with the correct hardware checksum.
Signed-off-by: Gurucharan Shetty <gshetty@riverbed.com> Signed-off-by: Arthur Jones <ajones@riverbed.com> Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe: Fix 82598 premature copper PHY link indicatation
Modified patch with Dave's comments to replace mdelay with proper msleep.
Fix 82598 copper link issue, where the phy prematurely indicates link
before it is ready to process packets. The new function looks for phy
link and indicates that, when it is available. If phy is not ready
within few seconds of MAC indicating link, the function will return
failure which translates to link down indication.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the restart_queue and non_eop_desc counters from being
double-counted. They are cumulative in each ring, so we don't want to
add them to the cumulative result in the adapter's master counter.
Otherwise, the stats will be inaccurate
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 15 Dec 2009 05:47:03 +0000 (05:47 +0000)]
packet: dont call sleeping functions while holding rcu_read_lock()
commit 654d1f8a019dfa06d (packet: less dev_put() calls)
introduced a problem, calling potentially sleeping functions from a
rcu_read_lock() protected section.
Fix this by releasing lock before the sock_wmalloc()/memcpy_fromiovec() calls.
After skb allocation and copy from user space, we redo device
lookup and appropriate tests.
Reported-and-tested-by: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is likely caused by the change in the 'estab' parameter
passed to tcp_parse_options() when invoked by the functions
in net/ipv4/tcp_minisocks.c
But even if that is fixed, the ->conn_request() changes made in
this patch series is fundamentally wrong. They try to use the
listening socket's 'dst' to probe the route settings. The
listening socket doesn't even have a route, and you can't
get the right route (the child request one) until much later
after we setup all of the state, and it must be done by hand.
This stuff really isn't ready, so the best thing to do is a
full revert. This reverts the following commits:
Simon Horman [Tue, 15 Dec 2009 16:01:25 +0000 (17:01 +0100)]
ipvs: zero usvc and udest
Make sure that any otherwise uninitialised fields of usvc are zero.
This has been obvserved to cause a problem whereby the port of
fwmark services may end up as a non-zero value which causes
scheduling of a destination server to fail for persisitent services.
As observed by Deon van der Merwe <dvdm@truteq.co.za>.
This fix suggested by Julian Anastasov <ja@ssi.bg>.
For good measure also zero udest.
Cc: Deon van der Merwe <dvdm@truteq.co.za> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Cc: stable@kernel.org Signed-off-by: Patrick McHardy <kaber@trash.net>
Patrick McHardy [Tue, 15 Dec 2009 15:59:59 +0000 (16:59 +0100)]
netfilter: fix crashes in bridge netfilter caused by fragment jumps
When fragments from bridge netfilter are passed to IPv4 or IPv6 conntrack
and a reassembly queue with the same fragment key already exists from
reassembling a similar packet received on a different device (f.i. with
multicasted fragments), the reassembled packet might continue on a different
codepath than where the head fragment originated. This can cause crashes
in bridge netfilter when a fragment received on a non-bridge device (and
thus with skb->nf_bridge == NULL) continues through the bridge netfilter
code.
Add a new reassembly identifier for packets originating from bridge
netfilter and use it to put those packets in insolated queues.
Patrick McHardy [Tue, 15 Dec 2009 15:59:18 +0000 (16:59 +0100)]
ipv6: reassembly: use seperate reassembly queues for conntrack and local delivery
Currently the same reassembly queue might be used for packets reassembled
by conntrack in different positions in the stack (PREROUTING/LOCAL_OUT),
as well as local delivery. This can cause "packet jumps" when the fragment
completing a reassembled packet is queued from a different position in the
stack than the previous ones.
Add a "user" identifier to the reassembly queue key to seperate the queues
of each caller, similar to what we do for IPv4.
Since power management is done by PCI subsystem as well as driver,
don't toggle the bit that disables PCI register writes.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 14 Dec 2009 01:53:41 +0000 (01:53 +0000)]
x25: Update maintainer.
On Monday 14 December 2009, andrew hendry wrote:
> Thanks, I didn't know X.25 was actively maintained. I get bounces.
> Is the the maintainers out of date?
From looking at the posts on the x.25 mailing list and the changes
that went into the kernel during the last three years in that area,
I think it is safe to say that you are now the maintainer ;-).
The last mail on this topic from Henner Eisen was around 2001.
mac80211: Add define for TX headroom reserved by mac80211 itself.
Add a definition of the amount of TX headroom reserved by mac80211 itself
for its own purposes. Also add BUILD_BUG_ON to validate the value.
This define can then be used by drivers to request additional TX headroom
in the most efficient manner.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800lib incorrectly detected whether RT2800USB was enabled because
it didn't account for a modularized RT2800USB driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Xiaotian Feng [Mon, 14 Dec 2009 15:38:21 +0000 (16:38 +0100)]
ipvs: fix synchronization on connection close
commit 9d3a0de makes slaves expire as they would do on the master
with much shorter timeouts. But it introduces another problem:
When we close a connection, on master server the connection became
CLOSE_WAIT/TIME_WAIT, it was synced to slaves, but if master is
finished within it's timeouts (CLOSE), it will not be synced to
slaves. Then slaves will be kept on CLOSE_WAIT/TIME_WAIT until
timeout reaches. Thus we should also sync with CLOSE.
Cc: Wensong Zhang <wensong@linux-vs.org> Cc: Simon Horman <horms@verge.net.au> Cc: Julian Anastasov <ja@ssi.bg> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Xiaotian Feng <dfeng@redhat.com> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: Patrick McHardy <kaber@trash.net>
Joe Perches [Mon, 14 Dec 2009 04:06:07 +0000 (20:06 -0800)]
drivers/net/bonding/: : use pr_fmt
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove DRV_NAME from pr_<level>s
Consolidate long format strings
Remove some extra tab indents
Remove some unnecessary ()s from pr_<level>s arguments
Align pr_<level> arguments
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/can/mcp251x.c:1074: undefined reference to `dma_free_coherent'
drivers/net/can/mcp251x.c:976: undefined reference to `dma_alloc_coherent'
drivers/net/can/mcp251x.c:1050: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Sun, 13 Dec 2009 05:47:04 +0000 (05:47 +0000)]
drivers/net/usb: Correct code taking the size of a pointer
sizeof(dev->dev_addr) is the size of a pointer. A few lines above, the
size of this field is obtained using netdev->addr_len for a call to memcpy,
so do the same here.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Sun, 13 Dec 2009 01:41:29 +0000 (01:41 +0000)]
drivers/net/sfc: Correct code taking the size of a pointer
The function efx_iterate_state contains the code
memcpy(&payload->msg, payload_msg, sizeof(payload_msg));
This is the only use of payload_msg. The type of payload_msg is
changed from a pointer to an array, so that the result of sizeof really is
the length of the string.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Sat, 12 Dec 2009 04:13:21 +0000 (04:13 +0000)]
can: Fix data length code handling in rx path
A valid CAN dataframe can have a data length code (DLC) of 0 .. 8 data bytes.
When reading the CAN controllers register the 4-bit value may contain values
from 0 .. 15 which may exceed the reserved space in the socket buffer!
The ISO 11898-1 Chapter 8.4.2.3 (DLC field) says that register values > 8
should be reduced to 8 without any error reporting or frame drop.
This patch introduces a new helper macro to cast a given 4-bit data length
code (dlc) to __u8 and ensure the DLC value to be max. 8 bytes.
The different handlings in the rx path of the CAN netdevice drivers are fixed.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
I received some bug reports about userspace programs having problems
because after RTM_NEWLINK was received they could not immediate access
files under /proc/sys/net/ because they had not been registered yet.
The original problem was trivially fixed by moving the userspace
notification from rtnetlink_event() to the end of
register_netdevice().
When testing that change I discovered I was still getting RTM_NEWLINK
events before I could access proc and I was also getting RTM_NEWLINK
events after I was seeing RTM_DELLINK. Things practically guaranteed
to confuse userspace.
After a little more investigation these extra notifications proved to
be from the new notifiers NETDEV_POST_INIT and NETDEV_UNREGISTER_BATCH
hitting the default case in rtnetlink_event, and triggering
unnecessary RTM_NEWLINK messages.
rtnetlink_event now explicitly handles NETDEV_UNREGISTER_BATCH and
NETDEV_POST_INIT to avoid sending the incorrect userspace
notifications.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 14 Dec 2009 03:32:39 +0000 (19:32 -0800)]
udp: udp_lib_get_port() fix
Now we can have a large udp hash table, udp_lib_get_port() loop
should be converted to a do {} while (cond) form,
or we dont enter it at all if hash table size is exactly 65536.
Reported-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Sat, 12 Dec 2009 06:58:14 +0000 (22:58 -0800)]
igbvf: avoid reset storms due to mailbox issues
From: Alexander Duyck <alexander.h.duyck@intel.com>
This change makes it so that reset/interrupt storms can be avoided when
there are mailbox issues. The new behavior is to only allow the device to
trigger mailbox related resets only once every 10 seconds.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Sat, 12 Dec 2009 06:57:34 +0000 (22:57 -0800)]
igb: fix handling of mailbox collisions between PF/VF
This patch changes the handling of collisions between the use of the
PF/VF sides of the mailbox.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Sat, 12 Dec 2009 05:43:00 +0000 (21:43 -0800)]
usb: remove rare pm primitive for conversion to new API
This patch removes a rare use of the USB power management API which
won't be supported after the conversion to the new generic runtime power
management framework. Functionality is not altered.
Signed-off-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 11 Dec 2009 23:59:23 +0000 (15:59 -0800)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[ACPI/CPUFREQ] Introduce bios_limit per cpu cpufreq sysfs interface
[CPUFREQ] make internal cpufreq_add_dev_* static
[CPUFREQ] use an enum for speedstep processor identification
[CPUFREQ] Document units for transition latency
[CPUFREQ] Use global sysfs cpufreq structure for conservative governor tunings
[CPUFREQ] Documentation: ABI: /sys/devices/system/cpu/cpu#/cpufreq/
[CPUFREQ] powernow-k6: set transition latency value so ondemand governor can be used
[CPUFREQ] cpumask: don't put a cpumask on the stack in x86...cpufreq/powernow-k8.c
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (58 commits)
tty: split the lock up a bit further
tty: Move the leader test in disassociate
tty: Push the bkl down a bit in the hangup code
tty: Push the lock down further into the ldisc code
tty: push the BKL down into the handlers a bit
tty: moxa: split open lock
tty: moxa: Kill the use of lock_kernel
tty: moxa: Fix modem op locking
tty: moxa: Kill off the throttle method
tty: moxa: Locking clean up
tty: moxa: rework the locking a bit
tty: moxa: Use more tty_port ops
tty: isicom: fix deadlock on shutdown
tty: mxser: Use the new locking rules to fix setserial properly
tty: mxser: use the tty_port_open method
tty: isicom: sort out the board init logic
tty: isicom: switch to the new tty_port_open helper
tty: tty_port: Add a kref object to the tty port
tty: istallion: tty port open/close methods
tty: stallion: Convert to the tty_port_open/close methods
...
Linus Torvalds [Fri, 11 Dec 2009 23:31:13 +0000 (15:31 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: (21 commits)
ext3: PTR_ERR return of wrong pointer in setup_new_group_blocks()
ext3: Fix data / filesystem corruption when write fails to copy data
ext4: Support for 64-bit quota format
ext3: Support for vfsv1 quota format
quota: Implement quota format with 64-bit space and inode limits
quota: Move definition of QFMT_OCFS2 to linux/quota.h
ext2: fix comment in ext2_find_entry about return values
ext3: Unify log messages in ext3
ext2: clear uptodate flag on super block I/O error
ext2: Unify log messages in ext2
ext3: make "norecovery" an alias for "noload"
ext3: Don't update the superblock in ext3_statfs()
ext3: journal all modifications in ext3_xattr_set_handle
ext2: Explicitly assign values to on-disk enum of filetypes
quota: Fix WARN_ON in lookup_one_len
const: struct quota_format_ops
ubifs: remove manual O_SYNC handling
afs: remove manual O_SYNC handling
kill wait_on_page_writeback_range
vfs: Implement proper O_SYNC semantics
...
Linus Torvalds [Fri, 11 Dec 2009 23:30:29 +0000 (15:30 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: Fix error return for fallocate() on XFS
xfs: cleanup dmapi macros in the umount path
xfs: remove incorrect sparse annotation for xfs_iget_cache_miss
xfs: kill the STATIC_INLINE macro
xfs: uninline xfs_get_extsz_hint
xfs: rename xfs_attr_fetch to xfs_attr_get_int
xfs: simplify xfs_buf_get / xfs_buf_read interfaces
xfs: remove IO_ISAIO
xfs: Wrapped journal record corruption on read at recovery
xfs: cleanup data end I/O handlers
xfs: use WRITE_SYNC_PLUG for synchronous writeout
xfs: reset the i_iolock lock class in the reclaim path
xfs: I/O completion handlers must use NOFS allocations
xfs: fix mmap_sem/iolock inversion in xfs_free_eofblocks
xfs: simplify inode teardown
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (235 commits)
Staging: IIO: add selection of IIO_SW_RING to LIS3L02DQ as needed
Staging: IIO: Add tsl2560-2 support to tsl2563 driver.
Staging: IIO: Remove tsl2561 driver. Support merged with tsl2563.
Staging: wlags49_h2: fix up signal levels
+ drivers-staging-wlags49_h2-remove-cvs-metadata.patch added to -mm tree
Staging: samsung-laptop: add TODO file
Staging: samsung-laptop: remove old kernel code
Staging: add Samsung Laptop driver
staging: batman-adv meshing protocol
Staging: rtl8192u: depends on USB
Staging: rtl8192u: remove dead code
Staging: rtl8192u: remove bad whitespaces
Staging: rtl8192u: make it compile
Staging: Added Realtek rtl8192u driver to staging
Staging: dream: add gpio and pmem support
Staging: dream: add TODO file
Staging: android: delete android drivers
Staging: et131x: clean up the avail fields in the rx registers
Staging: et131x: Clean up number fields
Staging: et131x: kill RX_DMA_MAX_PKT_TIME
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (27 commits)
Driver core: fix race in dev_driver_string
Driver Core: Early platform driver buffer
sysfs: sysfs_setattr remove unnecessary permission check.
sysfs: Factor out sysfs_rename from sysfs_rename_dir and sysfs_move_dir
sysfs: Propagate renames to the vfs on demand
sysfs: Gut sysfs_addrm_start and sysfs_addrm_finish
sysfs: In sysfs_chmod_file lazily propagate the mode change.
sysfs: Implement sysfs_getattr & sysfs_permission
sysfs: Nicely indent sysfs_symlink_inode_operations
sysfs: Update s_iattr on link and unlink.
sysfs: Fix locking and factor out sysfs_sd_setattr
sysfs: Simplify iattr time assignments
sysfs: Simplify sysfs_chmod_file semantics
sysfs: Use dentry_ops instead of directly playing with the dcache
sysfs: Rename sysfs_d_iput to sysfs_dentry_iput
sysfs: Update sysfs_setxattr so it updates secdata under the sysfs_mutex
debugfs: fix create mutex racy fops and private data
Driver core: Don't remove kobjects in device_shutdown.
firmware_class: make request_firmware_nowait more useful
Driver-Core: devtmpfs - set root directory mode to 0755
...
Linus Torvalds [Fri, 11 Dec 2009 23:22:27 +0000 (15:22 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: ohci: handle receive packets with a data length of zero
Linus Torvalds [Fri, 11 Dec 2009 23:19:56 +0000 (15:19 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb: Always process the whole breakpoint list on activate or deactivate
kgdb: continue and warn on signal passing from gdb
kgdb,x86: do not set kgdb_single_step on x86
kgdb: allow for cpu switch when single stepping
kgdb,i386: Fix corner case access to ss with NMI watch dog exception
kgdb: Replace strstr() by strchr() for single-character needles
kgdbts: Read buffer overflow
kgdb: Read buffer overflow
kgdb,x86: remove redundant test