Andrew Duggan [Mon, 8 Dec 2014 23:02:00 +0000 (15:02 -0800)]
HID: rmi: The address of query8 must be calculated based on which query registers are present
If a touchpad does not report relative data then query 6 will not be present and the address
of query 8 will be one less. This patches calculates the location of query 8 instead of
hardcoding the offset.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Andrew Duggan [Mon, 8 Dec 2014 23:01:59 +0000 (15:01 -0800)]
HID: rmi: Check for additional ACM registers appended to F11 data report
If a touchpad reports the F11 data40 register then this indicates that the touchpad reports
additional ACM (Accidental Contact Mitigation) data after the F11 data in the HID attention
report. These additional bytes shift the position of the F30 button data causing the driver
to incorrectly report button state when this functionality is present. This patch accounts
for the additional data in the report.
Gwendal Grignou [Fri, 12 Dec 2014 00:02:45 +0000 (16:02 -0800)]
HID: i2c-hid: prevent buffer overflow in early IRQ
Before ->start() is called, bufsize size is set to HID_MIN_BUFFER_SIZE,
64 bytes. While processing the IRQ, we were asking to receive up to
wMaxInputLength bytes, which can be bigger than 64 bytes.
Later, when ->start is run, a proper bufsize will be calculated.
Given wMaxInputLength is said to be unreliable in other part of the
code, set to receive only what we can even if it results in truncated
reports.
Peter Wu [Thu, 11 Dec 2014 12:51:20 +0000 (13:51 +0100)]
HID: logitech-hidpp: disable io in probe error path
Balance a hid_device_io_start() call with hid_device_io_stop() in the
error path. This avoids processing of HID reports when the probe fails
which possibly leads to invalid memory access in hid_device_probe() as
report_enum->report_id_hash might already be freed via
hid_close_report().
hid_set_drvdata() is called before wtp_allocate, be consistent and clear
drvdata too on the error path of wtp_allocate.
Signed-off-by: Peter Wu <peter@lekensteyn.nl> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Peter Wu [Thu, 11 Dec 2014 12:51:18 +0000 (13:51 +0100)]
HID: logitech-hidpp: check name retrieval return code
hidpp_devicenametype_get_device_name() may return a negative value on
protocol errors (for example, when the device is powered off).
Explicitly check this condition to avoid a long-running loop.
(0 cannot be returned as __name_length - index > 0, but check for it
anyway as it would otherwise result in an infinite loop.)
Signed-off-by: Peter Wu <peter@lekensteyn.nl> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Peter Wu [Thu, 11 Dec 2014 12:51:17 +0000 (13:51 +0100)]
HID: logitech-hidpp: do not return the name length
We do not make any use of the actual name length get through
hidpp_get_device_name(). Original patch by Benjamin Tissoires, this
patch also replaces a (now) unnecessary goto by return NULL.
Signed-off-by: Peter Wu <peter@lekensteyn.nl> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jason Gerecke [Thu, 11 Dec 2014 00:26:04 +0000 (16:26 -0800)]
HID: wacom: Report input events for each finger on generic devices
The existing generic touch code only reports events after reading an
entire HID report, which practically means that only data about the last
contact in a report will ever be provided to userspace. This patch uses
a trick from hid-multitouch.c to discover what type of field is at the
end of each contact; when such a field is encountered all the stored
contact data will be reported.
Signed-off-by: Jason Gerecke <killertofu@gmail.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jason Gerecke [Fri, 5 Dec 2014 21:37:32 +0000 (13:37 -0800)]
HID: wacom: Initialize MT slots for generic devices at post_parse_hid
If a HID descriptor places HID_DG_CONTACTID before HID_DG_X and HID_DG_Y then
the ABS_X and ABS_Y will not be automatically initialized by the call to
input_mt_init_slots. To ensure that this is not a problem, we relocate that
call to occur after HID parsing has been completed and we've initalized all the
multitouch axes.
Signed-off-by: Jason Gerecke <killertofu@gmail.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
So here, wacom_open is called, and then wacom_resume is called by the
PM system. However, wacom_open already took the lock when wacom_resume
tries to get it. Freeze.
A little bit of history shows that this already happened in the past
- commit f6cd378372bf ("Input: wacom - fix runtime PM related deadlock"),
and the solution was to call first the PM function before taking the lock.
The lock was introduced in commit commit e722409445fb ("Input: wacom -
implement suspend and autosuspend") when the autosuspend feature has
been added. Given that usbhid already takes care of this very same
locking between suspend/resume, I think we can simply kill the lock
in open/close.
The lock is now used also with LEDs, so we can not remove it completely.
Reported-by: Hans Spath <inbox-546@hans-spath.de> Tested-by: Hans Spath <inbox-546@hans-spath.de> CC: stable@vger.kernel.org # v3.17+ Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID: make hid_report_len as a static inline function in hid.h
In several hid drivers it is necessary to calculate the length of an
hid_report. This patch exports the existing static function hid_report_len of
hid-core.c as an inline function in hid.h
Signed-off-by: Mathieu Magnaudet <mathieu.magnaudet@enac.fr> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com> Reviewed-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jason Gerecke [Mon, 24 Nov 2014 23:32:12 +0000 (15:32 -0800)]
HID: wacom: Consult the application usage when determining field type
It is not necessarily sufficient to look only at the physical and logical
usages when determining if a field is for the pen or touch. Some fields
are not contained in a sub-collection and thus only have an application
usage. Not checking the application usage in such cases causes us to
ignore the field entirely, which may lead to incorrect behavior.
Signed-off-by: Jason Gerecke <killertofu@gmail.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ping Cheng [Fri, 21 Nov 2014 00:31:12 +0000 (16:31 -0800)]
HID: wacom: PAD is independent with pen/touch
PAD can be on pen interface (Intuos Pro and Cintiq series) or touch
interface (Bamboo PT and Intuos PT series) or its own interface
(Bamboo pen-only and Intuos Pen M/S). We need to mark it independently.
VTL panels do not switch to the multitouch mode until the input mode
feature is read by the host. This should normally be done by
usbhid, but it looks like an other bug prevents usbhid to properly
retrieve the feature state. As a workaround, we force the reading of
the feature in mt_set_input_mode for such devices.
Current driver uses a common buffer for reading reports either
synchronously in i2c_hid_get_raw_report() and asynchronously in
the interrupt handler.
There is race condition if an interrupt arrives immediately after
the report is received in i2c_hid_get_raw_report(); the common
buffer is modified by the interrupt handler with the new report
and then i2c_hid_get_raw_report() proceed using wrong data.
Fix it by using a separate buffers for synchronous reports.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
[Antonio Borneo: cleanup, rebase to v3.17, submit mainline] Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jason Gerecke [Wed, 19 Nov 2014 00:50:09 +0000 (16:50 -0800)]
HID: wacom: Add angular resolution data to some ABS axes
Provide the resolution of several angular axes (tilt, pen rotation, puck
rotation) to userspace. Because these values are natively degree-based, we
need to convert them to into units/radian as required by the input_absinfo
struct. To ensure wraparound behaves properly for the rotation axes, the
converted value was rounded up rather than rounded nearest.
Notably, the touchring axes (ABS_WHEEL and ABS_THROTTLE) are left without a
a declared resolution because the their low resolution cannot be accurately
represented (the worst-case rounding-induced error would be ~16 degrees).
Pre-scaling the values and range by at least 10x would reduce the error in
the resolution to acceptable levels, but the xf86-input-wacom driver is not
able to use pre-scaled values for these axes at this time.
Jason Gerecke [Wed, 19 Nov 2014 00:50:08 +0000 (16:50 -0800)]
HID: wacom: Report ABS_TILT_{X,Y} as signed values
Centers the ABS_TILT_{X,Y} axes so that a value of zero is reported when
the pen is vertical. Combined with resolution information in the next
patch, this makes it possible for userspace to calculate the pen angle
without needing hardware-specific knowledge. The xf86-input-wacom driver
was updated to support signed tilt values in late-2012 (2f2acec).
Report is received in "buffer"; fix the following i2c_hid_dbg()
to dump data from the correct pointer.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
[Antonio Borneo: cleanup and rebase to v3.17] Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds [Fri, 14 Nov 2014 00:19:14 +0000 (16:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix for an oops in HID core upon repeated subdriver insertion/removal
under certain circumstances, by Benjamin Tissoires
- quirk for another Elan Touchscreen device, by Adel Gadllah
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: cleanup .claimed field on disconnect
HID: usbhid: enable always-poll quirk for Elan Touchscreen 0103
Linus Torvalds [Thu, 13 Nov 2014 17:57:04 +0000 (09:57 -0800)]
Merge tag 'sound-3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Things get calming down, now we have only a few fix patches: a trivial
fix for memory leak in usb-audio, a patch for the new HD-audio PCI id,
a device-specific mute-LED fix, and a slightly big patch to cover the
missing COEF inits of various Realtek codecs"
* tag 'sound-3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add mute LED control for Lenovo Ideapad Z560
ALSA: hda/realtek - Change EAPD to verb control
ALSA: usb-audio: Fix memory leak in FTU quirk
ALSA: hda_intel: Add DeviceIDs for Sunrise Point-LP
Linus Torvalds [Thu, 13 Nov 2014 17:46:15 +0000 (09:46 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull SELinux fixlet from James Morris:
"WARN_ONCE() here will unnecessarily terrify users"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: convert WARN_ONCE() to printk() in selinux_nlmsg_perm()
Linus Torvalds [Thu, 13 Nov 2014 17:36:39 +0000 (09:36 -0800)]
Merge branch 'stable-3.18' of git://git.infradead.org/users/pcmoore/audit
Pull audit fixes from Paul Moore:
"After he sent the initial audit pull request for 3.18, Eric asked me
to take over the management of the audit tree, hence this pull request
to fix a couple of problems with audit.
As you can see below, the changes are minimal: adding some whitespace
to a string so userspace parses it correctly, and fixing a problem
with audit's usage of fsnotify that was causing audit watch rules to
be lost. Neither of these patches were very controversial on the
mailing lists and they fix real problems, getting them into 3.18 would
be a good thing"
* 'stable-3.18' of git://git.infradead.org/users/pcmoore/audit:
audit: keep inode pinned
audit: AUDIT_FEATURE_CHANGE message format missing delimiting space
Linus Torvalds [Thu, 13 Nov 2014 17:19:20 +0000 (09:19 -0800)]
Merge tag 'dm-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- stable fix for dm-thin that avoids normal IO racing with discard
- stable fix for a dm-cache related bug in dm-btree walking code that
results from using very large fast device (eg 4T) with a very small
cache blocksize (eg 32K) -- this is a very uncommon configuration
- a couple fixes for dm-raid (one for stable and the other addresses a
crash in 3.18-rc1 code)
- stable fix for dm-thinp that addresses a very rare dm-bufio bug
having to do with memory reclaimation (via shrinker) when using
dm-thinp ontop of loopback devices
- fix a leak in dm-stripe target constructor's error path
* tag 'dm-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm btree: fix a recursion depth bug in btree walking code
dm thin: grab a virtual cell before looking up the mapping
dm raid: fix inaccessible superblocks causing oops in configure_discard_support
dm raid: ensure superblock's size matches device's logical block size
dm bufio: change __GFP_IO to __GFP_FS in shrinker callbacks
dm stripe: fix potential for leak in stripe_ctr error path
Takashi Iwai [Wed, 12 Nov 2014 07:11:56 +0000 (08:11 +0100)]
ALSA: hda - Add mute LED control for Lenovo Ideapad Z560
Lenovo Ideapad Z560 has a mute LED that is controlled via EAPD pin
0x1b on CX20585 codec. (EAPD bit on corresponds to mute LED on.)
The machine doesn't need other EAPD, so the fixup concentrates on
controlling EAPD 0x1b following the vmaster state (but inversely).
Linus Torvalds [Wed, 12 Nov 2014 23:29:28 +0000 (15:29 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Two fixes --- one of them not exactly a one liner, but things are
calming down on the KVM front at last"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix uninitialized op->type for some immediate values
KVM: s390: virtio_ccw: remove unused variable
Linus Torvalds [Wed, 12 Nov 2014 23:21:52 +0000 (15:21 -0800)]
Merge tag 'xtensa-20141109' of git://github.com/czankel/xtensa-linux
Pull Xtensa fixes from Chris Zankel:
- fix umount syscall
- fix ISS and xtfpga Kconfig dependencies so that more randconfigs are
buildable
- add seccomp, getrandom, and memfd_create syscalls
- add defconfigs for KC705 and SMP LX200
- implement pgprot_noncached
* tag 'xtensa-20141109' of git://github.com/czankel/xtensa-linux:
xtensa: xtfpga: add lx200 SMP DTS and defconfig
xtensa: xtfpga: add generic KC705 board config
xtensa: re-wire umount syscall to sys_oldumount
xtensa: xtfpga: only select ethoc when ethernet is available
xtensa: add seccomp, getrandom, and memfd_create syscalls
xtensa: ISS: add BLOCK dependency to BLK_DEV_SIMDISK
xtensa: implement pgprot_noncached
xtensa/uapi: Add definition of TIOC[SG]RS485
Pull crypto fixes from Herbert Xu:
- stack corruption fix for pseries hwrng driver
- add missing DMA unmap in caam crypto driver
- fix NUMA crash in qat crypto driver
- fix buggy mapping of zero-length associated data in qat crypto driver
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: pseries - port to new read API and fix stack corruption
crypto: caam - fix missing dma unmap on error path
crypto: qat - Enforce valid numa configuration
crypto: qat - Prevent dma mapping zero length assoc data
Linus Torvalds [Wed, 12 Nov 2014 22:02:29 +0000 (14:02 -0800)]
Merge tag 'trace-fixes-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Rabin Vincent found a way that tracing could cause an infinite loop in
the kernel. The splice logic wants a full page from the ring buffer
but the ring_buffer_wait() returns when there's any data in the ring
buffer. The splice code would then continue the loop waiting for a
full page. But if a full page never happens, the splice code will
never sleep and just continue to loop.
There's another case that Rabin fixed that could loop if there's no
memory and kmalloc() constantly returns NULL"
* tag 'trace-fixes-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do not risk busy looping in buffer splice
tracing: Do not busy wait in buffer splice
Linus Torvalds [Wed, 12 Nov 2014 21:18:20 +0000 (13:18 -0800)]
Merge tag 'hwmon-for-linus-v3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- fix PCI device ID in fam15h_power driver
- fix suspend/resume behavior in pwm-fan driver
- reduce logging noise created by ibmpowernv driver
* tag 'hwmon-for-linus-v3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (fam15h_power) Fix NB device ID for F16h M30h
hwmon: (pwm-fan) Fix suspend/resume behavior
hwmon: (ibmpowernv) Quieten when probing finds no device
Linus Torvalds [Wed, 12 Nov 2014 21:15:18 +0000 (13:15 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal driver fixes from Eduardo Valentin:
"This week we have few fixes:
- fix in IMX thermal driver to do the correct loading sequence with
CPUfreq
- fix in Exynos related to TMU_CONTROL offset in Exynos5260
- fix the unit conversion in int3403"
[ Still pulling from Eduardo as Rui Zhang is on a business trip and has
troubles with his machine ]
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
imx: thermal: imx_get_temp might be called before sensor clock is prepared
thermal: exynos: use correct offset for TMU_CONTROL register on Exynos5260
thermal: imx: correct driver load sequence for cpu cooling
Thermal/int3403: Fix thermal hysteresis unit conversion
selinux: convert WARN_ONCE() to printk() in selinux_nlmsg_perm()
Convert WARN_ONCE() to printk() in selinux_nlmsg_perm().
After conversion from audit_log() in commit e173fb26, WARN_ONCE() was
deemed too alarmist, so switch it to printk().
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: Changed to printk(WARNING) so we catch all of the different
invalid netlink messages. In Richard's defense, he brought this
point up earlier, but I didn't understand his point at the time.] Signed-off-by: Paul Moore <pmoore@redhat.com>
Linus Torvalds [Wed, 12 Nov 2014 21:13:24 +0000 (13:13 -0800)]
Merge tag 'mfd-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
- register offset fix for stmpe
- eradicate build warning when !PM in rtsx_pcr
- fix device ID collision when multiple boards are connected in
viperboard
- use correct Regmap handle - fixing unhanded IRQs in max77693
- unmask MUIC IRQs in max77693
- clear VBUS & CHG bits so board doesn't reboot instead of poweroff in
twl4030
* tag 'mfd-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: twl4030-power: Fix poweroff with PM configuration enabled
mfd: max77693: Fix always masked MUIC interrupts
mfd: max77693: Use proper regmap for handling MUIC interrupts
mfd: viperboard: Fix platform-device id collision
mfd: rtsx: Fix build warnings for !PM
mfd: stmpe: Fix STMPE24xx GPMR LSB
Linus Torvalds [Wed, 12 Nov 2014 20:37:45 +0000 (12:37 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon and i915 fixes.
I probably should have sent these earlier, but nothing too urgent in
them:
- i915:
blackscreen and corruption fixes
- radeon:
oops, locking and stability"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: add missing crtc unlock when setting up the MC
drm/radeon: use gart for DMA IB tests
drm/radeon: make sure mode init is complete in bandwidth_update
drm/radeon: set correct CE ram size for CIK
drm/i915: safeguard against too high minimum brightness
drm/i915: vlv: fix gunit HW state corruption during S4 suspend
drm/i915: Disable caches for Global GTT.
Kailang Yang [Wed, 12 Nov 2014 09:38:08 +0000 (17:38 +0800)]
ALSA: hda/realtek - Change EAPD to verb control
This will fix no sound in Linux system after reboot from windows.
Change log:
- alc662_fill_coef() is replaced with alc_fill_eapd_coef_idx()
and move into alc_auto_init_amp().
- For ALC262, ALC267, ALC268, ALC269, ALC233, ALC255, ALC280, ALC282,
ALC283, ALC284, ALC285, ALC286, ALC288, ALC290, ALC292, ALC293, ALC294,
ALC668, ALC888VC, ALC888VD, ALC891, ALC892, ALC898 and ALC1150, add update
COEF control for EAPD setting.
- Remove alc269_fill_coef() for update EAPD control line.
ADDITIONAL NOTE:
Many Realtek cdoecs have a COEF bit to switch the master amp control
between COEF and EAPD. Windows drivers seem using COEF while we use
EAPD, which is more standard. As a result, some system suffer from
the silent output when booting after Windows. This patch sets the
COEF bits on the relevant codecs properly to switch to EAPD control.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=87771 Signed-off-by: Kailang Yang <kailang@realtek.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Miklos Szeredi [Tue, 4 Nov 2014 10:27:12 +0000 (11:27 +0100)]
audit: keep inode pinned
Audit rules disappear when an inode they watch is evicted from the cache.
This is likely not what we want.
The guilty commit is "fsnotify: allow marks to not pin inodes in core",
which didn't take into account that audit_tree adds watches with a zero
mask.
Adding any mask should fix this.
Fixes: 90b1e7a57880 ("fsnotify: allow marks to not pin inodes in core") Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Cc: stable@vger.kernel.org # 2.6.36+ Signed-off-by: Paul Moore <pmoore@redhat.com>
Kamil Debski [Mon, 3 Nov 2014 14:42:55 +0000 (15:42 +0100)]
hwmon: (pwm-fan) Fix suspend/resume behavior
The state of a PWM output is not clearly defined after resume. Some PWM
drivers do not restore the duty cycle upon resume, thus it is necessary to
manually restore the correct value.
Michael Ellerman [Fri, 31 Oct 2014 06:45:22 +0000 (17:45 +1100)]
hwmon: (ibmpowernv) Quieten when probing finds no device
Because we build kernels with drivers built in for many platforms, it's
normal for the ibmpowernv driver to be loaded on systems that don't have
the appropriate hardware.
Currently the driver spams the log with:
ibmpowernv ibmpowernv.0: Opal node 'sensors' not found
ibmpowernv: Platfrom driver probe failed
But there is no error, this machine is not a powernv and doesn't have
the hardware. So change the sensors message to dev_dbg(), and only print
an error about the probe failing if it's not ENODEV.
Also fix the spelling of "Platfrom" and print the actual error value.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Jamie Lentin [Sun, 9 Nov 2014 07:54:29 +0000 (07:54 +0000)]
HID: lenovo: Move USB KEY_FILE to 0x00f9 to prevent scancode clash
The bluetooth keyboard also generates 0x00fa when the middle button is
pressed. Move the made-up report out of the way so we don't trigger
KEY_FILE when middle button is pressed
Alan Wu [Tue, 4 Nov 2014 02:26:12 +0000 (18:26 -0800)]
HID: add support for MS Surface Pro 3 Type Cover
Surface Pro 3 Type Cover that works with Ubuntu (and possibly Arch) from this thread. Both trackpad and keyboard work after compiling my own kernel.
http://ubuntuforums.org/showthread.php?t=2231207&page=2&s=44910e0c56047e4f93dfd9fea58121ef
Also includes Jarrad Whitaker's message which sources
http://winaero.com/blog/how-to-install-linux-on-surface-pro-3/
which he says is sourced from a Russian site
Signed-off-by: Alan Wu <alan.c.wu@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Daniel Thompson [Tue, 11 Nov 2014 05:59:46 +0000 (16:29 +1030)]
param: fix crash on bad kernel arguments
Currently if the user passes an invalid value on the kernel command line
then the kernel will crash during argument parsing. On most systems this
is very hard to debug because the console hasn't been initialized yet.
This is a regression due to commit 51e158c12aca ("param: hand arguments
after -- straight to init") which, in response to the systemd debug
controversy, made it possible to explicitly pass arguments to init. To
achieve this parse_args() was extended from simply returning an error
code to returning a pointer. Regretably the new init args logic does not
perform a proper validity check on the pointer resulting in a crash.
This patch fixes the validity check. Should the check fail then no arguments
will be passed to init. This is reasonable and matches how the kernel treats
its own arguments (i.e. no error recovery).
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org> Cc: stable@vger.kernel.org Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rabin Vincent [Thu, 6 Nov 2014 21:26:07 +0000 (22:26 +0100)]
tracing: Do not risk busy looping in buffer splice
If the read loop in trace_buffers_splice_read() keeps failing due to
memory allocation failures without reading even a single page then this
function will keep busy looping.
Remove the risk for that by exiting the function if memory allocation
failures are seen.
The problem is this: tracing_buffers_splice_read() calls
ring_buffer_wait() to wait for data in the ring buffers. The buffers
are not empty so ring_buffer_wait() returns immediately. But
tracing_buffers_splice_read() calls ring_buffer_read_page() with full=1,
meaning it only wants to read a full page. When the full page is not
available, tracing_buffers_splice_read() tries to wait again with
ring_buffer_wait(), which again returns immediately, and so on.
Fix this by adding a "full" argument to ring_buffer_wait() which will
make ring_buffer_wait() wait until the writer has left the reader's
page, i.e. until full-page reads will succeed.
Joe Thornber [Mon, 10 Nov 2014 15:03:24 +0000 (15:03 +0000)]
dm btree: fix a recursion depth bug in btree walking code
The walk code was using a 'ro_spine' to hold it's locked btree nodes.
But this data structure is designed for the rolling lock scheme, and
as such automatically unlocks blocks that are two steps up the call
chain. This is not suitable for the simple recursive walk algorithm,
which retraces its steps.
This code is only used by the persistent array code, which in turn is
only used by dm-cache. In order to trigger it you need to have a
mapping tree that is more than 2 levels deep; which equates to 8-16
million cache blocks. For instance a 4T ssd with a very small block
size of 32k only just triggers this bug.
The fix just places the locked blocks on the stack, and stops using
the ro_spine altogether.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org
Tony Lindgren [Sun, 2 Nov 2014 18:07:56 +0000 (10:07 -0800)]
mfd: twl4030-power: Fix poweroff with PM configuration enabled
Commit e7cd1d1eb16f ("mfd: twl4030-power: Add generic reset
configuration") enabled configuring the PM features for twl4030.
This caused poweroff command to fail on devices that have the
BCI charger on twl4030 wired, or have power wired for VBUS.
Instead of powering off, the device reboots. This is because
voltage is detected on charger or VBUS with the default bits
enabled for the power transition registers.
To fix the issue, let's just clear VBUS and CHG bits as we want
poweroff command to keep the system powered off.
Fixes: e7cd1d1eb16f ("mfd: twl4030-power: Add generic reset configuration") Cc: stable@vger.kernel.org # v3.16+ Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
All interrupts coming from MUIC were ignored because interrupt source
register was masked.
The Maxim 77693 has a "interrupt source" - a separate register and interrupts
which give information about PMIC block triggering the individual
interrupt (charger, topsys, MUIC, flash LED).
By default bootloader could initialize this register to "mask all"
value. In such case (observed on Trats2 board) MUIC interrupts won't be
generated regardless of their mask status. Regmap irq chip was unmasking
individual MUIC interrupts but the source was masked
Before introducing regmap irq chip this interrupt source was unmasked,
read and acked. Reading and acking is not necessary but unmasking is.
Fixes: 342d669c1ee4 ("mfd: max77693: Handle IRQs using regmap") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
mfd: max77693: Use proper regmap for handling MUIC interrupts
Interrupts coming from Maxim77693 MUIC block (MicroUSB Interface
Controller) were not handled at all because wrong regmap was used for
MUIC's regmap_irq_chip.
The MUIC component of Maxim 77693 uses different I2C address thus second
regmap is created and used by max77693 extcon driver. The registers for
MUIC interrupts are also in that block and should be handled by that
second regmap.
However the regmap irq chip for MUIC was configured with default regmap
which could not read MUIC registers.
Fixes: 342d669c1ee4 ("mfd: max77693: Handle IRQs using regmap") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Johan Hovold [Fri, 26 Sep 2014 10:55:28 +0000 (12:55 +0200)]
mfd: viperboard: Fix platform-device id collision
Allow more than one viperboard to be connected by registering with
PLATFORM_DEVID_AUTO instead of PLATFORM_DEVID_NONE.
The subdevices are currently registered with PLATFORM_DEVID_NONE, which
will cause a name collision on the platform bus when a second viperboard
is plugged in:
viperboard 1-2.4:1.0: version 0.00 found at bus 001 address 004
------------[ cut here ]------------
WARNING: CPU: 0 PID: 181 at /home/johan/work/omicron/src/linux/fs/sysfs/dir.c:31 sysfs_warn_dup+0x74/0x84()
sysfs: cannot create duplicate filename '/bus/platform/devices/viperboard-gpio'
Modules linked in: i2c_viperboard viperboard netconsole [last unloaded: viperboard]
CPU: 0 PID: 181 Comm: bash Tainted: G W 3.17.0-rc6 #1
[<c0016bf4>] (unwind_backtrace) from [<c0013860>] (show_stack+0x20/0x24)
[<c0013860>] (show_stack) from [<c04305f8>] (dump_stack+0x24/0x28)
[<c04305f8>] (dump_stack) from [<c0040fb4>] (warn_slowpath_common+0x80/0x98)
[<c0040fb4>] (warn_slowpath_common) from [<c004100c>] (warn_slowpath_fmt+0x40/0x48)
[<c004100c>] (warn_slowpath_fmt) from [<c016f1bc>] (sysfs_warn_dup+0x74/0x84)
[<c016f1bc>] (sysfs_warn_dup) from [<c016f548>] (sysfs_do_create_link_sd.isra.2+0xcc/0xd0)
[<c016f548>] (sysfs_do_create_link_sd.isra.2) from [<c016f588>] (sysfs_create_link+0x3c/0x48)
[<c016f588>] (sysfs_create_link) from [<c02867ec>] (bus_add_device+0x12c/0x1e0)
[<c02867ec>] (bus_add_device) from [<c0284820>] (device_add+0x410/0x584)
[<c0284820>] (device_add) from [<c0289440>] (platform_device_add+0xd8/0x26c)
[<c0289440>] (platform_device_add) from [<c02a5ae4>] (mfd_add_device+0x240/0x344)
[<c02a5ae4>] (mfd_add_device) from [<c02a5ce0>] (mfd_add_devices+0xb8/0x110)
[<c02a5ce0>] (mfd_add_devices) from [<bf00d1c8>] (vprbrd_probe+0x160/0x1b0 [viperboard])
[<bf00d1c8>] (vprbrd_probe [viperboard]) from [<c030c000>] (usb_probe_interface+0x1bc/0x2a8)
[<c030c000>] (usb_probe_interface) from [<c028768c>] (driver_probe_device+0x14c/0x3ac)
[<c028768c>] (driver_probe_device) from [<c02879e4>] (__driver_attach+0xa4/0xa8)
[<c02879e4>] (__driver_attach) from [<c0285698>] (bus_for_each_dev+0x70/0xa4)
[<c0285698>] (bus_for_each_dev) from [<c0287030>] (driver_attach+0x2c/0x30)
[<c0287030>] (driver_attach) from [<c030a288>] (usb_store_new_id+0x170/0x1ac)
[<c030a288>] (usb_store_new_id) from [<c030a2f8>] (new_id_store+0x34/0x3c)
[<c030a2f8>] (new_id_store) from [<c02853ec>] (drv_attr_store+0x30/0x3c)
[<c02853ec>] (drv_attr_store) from [<c016eaa8>] (sysfs_kf_write+0x5c/0x60)
[<c016eaa8>] (sysfs_kf_write) from [<c016dc68>] (kernfs_fop_write+0xd4/0x194)
[<c016dc68>] (kernfs_fop_write) from [<c010fe40>] (vfs_write+0xb4/0x1c0)
[<c010fe40>] (vfs_write) from [<c01104a8>] (SyS_write+0x4c/0xa0)
[<c01104a8>] (SyS_write) from [<c000f900>] (ret_fast_syscall+0x0/0x48)
---[ end trace 98e8603c22d65817 ]---
viperboard 1-2.4:1.0: Failed to add mfd devices to core.
viperboard: probe of 1-2.4:1.0 failed with error -17
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Linus Walleij [Sat, 4 Oct 2014 14:02:27 +0000 (16:02 +0200)]
mfd: stmpe: Fix STMPE24xx GPMR LSB
The least significat byte of the GPIO value read register
on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct
against datasheet and tested on the STMPE2401 hardware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
Dave Airlie [Mon, 10 Nov 2014 00:05:37 +0000 (10:05 +1000)]
Merge tag 'drm-intel-fixes-2014-11-07' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Black screen, screen corruption, hardware state corruption fixes.
* tag 'drm-intel-fixes-2014-11-07' of git://anongit.freedesktop.org/drm-intel:
drm/i915: safeguard against too high minimum brightness
drm/i915: vlv: fix gunit HW state corruption during S4 suspend
drm/i915: Disable caches for Global GTT.
Linus Torvalds [Sun, 9 Nov 2014 22:49:56 +0000 (14:49 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: update defconfig for 3.18
arm64: compat: Enable bpf syscall
arm64: psci: fix cpu_suspend to check idle state type for index
Linus Torvalds [Sun, 9 Nov 2014 22:46:36 +0000 (14:46 -0800)]
Merge tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Linus Torvalds [Sun, 9 Nov 2014 22:30:24 +0000 (14:30 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"It's a one liner for an error cleanup path that leads to crashes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup
Linus Torvalds [Sun, 9 Nov 2014 22:11:58 +0000 (14:11 -0800)]
Merge tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 tiny fixes for 3.18-rc4.
One fixes up a long-stading race condition in the driver core for
removing directories in /sys/devices/virtual/ and the other 2 fix up
the wording of a new Kconfig option that was added in 3.18-rc1"
* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
sysfs: driver core: Fix glue dir race condition by gdp_mutex
Linus Torvalds [Sun, 9 Nov 2014 22:11:07 +0000 (14:11 -0800)]
Merge tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported"
* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging:iio:ade7758: Remove "raw" from channel name
staging:iio:ade7758: Fix check if channels are enabled in prenable
staging:iio:ade7758: Fix NULL pointer deref when enabling buffer
iio: as3935: allocate correct iio_device size
io: accel: kxcjk-1013: Fix iio_event_spec direction
iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Linus Torvalds [Sun, 9 Nov 2014 22:07:30 +0000 (14:07 -0800)]
Merge tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues"
* tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix pty master poll() after slave closes v2
serial: of-serial: fix uninitialized kmalloc variable
tty/vt: don't set font mappings on vc not supporting this
tty: serial: 8250_mtk: Fix quot calculation
tty: Prevent "read/write wait queue active!" log flooding
tty: Fix high cpu load if tty is unreleaseable
serial: Fix divide-by-zero fault in uart_get_divisor()
Linus Torvalds [Sun, 9 Nov 2014 22:05:53 +0000 (14:05 -0800)]
Merge tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
Heiner Kallweit [Sat, 8 Nov 2014 19:35:54 +0000 (20:35 +0100)]
imx: thermal: imx_get_temp might be called before sensor clock is prepared
imx_get_temp might be called before the sensor clock is prepared
thus resulting in a timeout of the first attempt to read temp:
thermal thermal_zone0: failed to read out thermal zone 0
Happened to me on a Utilite Standard with IMX6 Dual SoC.
Reason is that in imx_thermal_probe thermal_zone_device_register
is called before the sensor clock is prepared.
thermal_zone_device_register however calls
thermal_zone_device_update which eventually calls imx_get_temp.
Fix this by preparing the clock before calling
thermal_zone_device_register.
Andreas Färber [Thu, 6 Nov 2014 17:22:10 +0000 (18:22 +0100)]
ARM: dts: zynq: Enable PL clocks for Parallella
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x Signed-off-by: Andreas Färber <afaerber@suse.de> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 8 Nov 2014 17:32:29 +0000 (09:32 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bugfixes from Wolfram Sang:
"One bigger cleanup (FSF address removal) and two bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
Pull media fixes from Mauro Carvalho Chehab:
"For:
- some regression fixes at the Remote Controller core and imon driver
- a build fix for certain randconfigs with ir-hix5hd2
- don't feed power to satellite system at ds3000 driver init
It also contains some fixes for drivers added for Kernel 3.18:
- some fixes at the new ISDB-S driver, and the corresponding bits to
fix some descriptors for this Japanese TV standard at the DVB core
- two warning cleanups for sp2 driver if PM is disabled
- change the default mode for the new vivid driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] sp2: sp2_init() can be static
[media] dvb:tc90522: fix always-false expression
[media] dvb-core: set default properties of ISDB-S
[media] dvb:tc90522: fix stats report
[media] vivid: default to single planar device instances
[media] imon: fix other RC type protocol support
[media] ir-hix5hd2 fix build warning
[media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
[media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
[media] rc-core: fix protocol_change regression in ir_raw_event_register
Linus Torvalds [Sat, 8 Nov 2014 02:08:02 +0000 (18:08 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This weeks' round of MIPS bug fixes for 3.18:
- wire up the bpf syscall
- fix TLB dump output for R3000 class TLBs
- fix strnlen_user return value if no NUL character was found.
- fix build with binutils 2.24.51+. While there is no binutils 2.25
release yet, toolchains derived from binutils 2.24.51+ are already
in common use.
- the Octeon GPIO code forgot to offline GPIO IRQs.
- fix build error for XLP.
- fix possible BUG assertion with EVA for CMA"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix build with binutils 2.24.51+
MIPS: R3000: Fix debug output for Virtual page number
MIPS: Fix strnlen_user() return value in case of overlong strings.
MIPS: CMA: Do not reserve memory if not required
MIPS: Wire up bpf syscall.
MIPS/Xlp: Remove the dead function destroy_irq() to fix build error
MIPS: Octeon: Make Octeon GPIO IRQ chip CPU hotplug-aware
Linus Torvalds [Fri, 7 Nov 2014 22:08:13 +0000 (14:08 -0800)]
Merge tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This update fixes a warning in the new pagecache_isize_extended() and
updates some related comments, another fix for zero-range
misbehaviour, and an unforntuately large set of fixes for regressions
in the bulkstat code.
The bulkstat fixes are large but necessary. I wouldn't normally push
such a rework for a -rcX update, but right now xfsdump can silently
create incomplete dumps on 3.17 and it's possible that even xfsrestore
won't notice that the dumps were incomplete. Hence we need to get
this update into 3.17-stable kernels ASAP.
In more detail, the refactoring work I committed in 3.17 has exposed a
major hole in our QA coverage. With both xfsdump (the major user of
bulkstat) and xfsrestore silently ignoring missing files in the
dump/restore process, incomplete dumps were going unnoticed if they
were being triggered. Many of the dump/restore filesets were so small
that they didn't evenhave a chance of triggering the loop iteration
bugs we introduced in 3.17, so we didn't exercise the code
sufficiently, either.
We have already taken steps to improve QA coverage in xfstests to
avoid this happening again, and I've done a lot of manual verification
of dump/restore on very large data sets (tens of millions of inodes)
of the past week to verify this patch set results in bulkstat behaving
the same way as it does on 3.16.
Unfortunately, the fixes are not exactly simple - in tracking down the
problem historic API warts were discovered (e.g xfsdump has been
working around a 20 year old bug in the bulkstat API for the past 10
years) and so that complicated the process of diagnosing and fixing
the problems. i.e. we had to fix bugs in the code as well as
discover and re-introduce the userspace visible API bugs that we
unwittingly "fixed" in 3.17 that xfsdump relied on to work correctly.
Summary:
- incorrect warnings about i_mutex locking in pagecache_isize_extended()
and updates comments to match expected locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17"
* tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
xfs: rework zero range to prevent invalid i_size updates
mm: Remove false WARN_ON from pagecache_isize_extended()
xfs: Check error during inode btree iteration in xfs_bulkstat()
xfs: bulkstat doesn't release AGI buffer on error
Linus Torvalds [Fri, 7 Nov 2014 19:55:47 +0000 (11:55 -0800)]
Merge tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"More changes than I'd like here, most of them for a single bug
repeated in a bunch of drivers with data not being initialized
correctly, plus a fix to lower the severity of a warning introduced in
the last merge window which can legitimately go off so we don't want
to alarm users excessively"
* tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mpa01: zero-initialize regulator match table array
regulator: max8660: zero-initialize regulator match table array
regulator: max77802: zero-initialize regulator match table
regulator: max77686: zero-initialize regulator match table
regulator: max1586: zero-initialize regulator match table array
regulator: max77693: Fix use of uninitialized regulator config
regulator: of: Lower the severity of the error with no container
Linus Torvalds [Fri, 7 Nov 2014 19:54:44 +0000 (11:54 -0800)]
Merge tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi bugfixes from Mark Brown:
"A couple of small driver fixes for v3.18, both quite problematic if
you hit a use case that's affected"
* tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: toggle clocks on suspend if not disabled by runtime PM
spi: fsl-dspi: Fix CTAR selection
Johannes Berg [Thu, 30 Oct 2014 09:00:35 +0000 (10:00 +0100)]
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
The ENABLE_DEV_COREDUMP option is misleading as it implies that
it gets the framework enabled, this isn't true it just allows it
to get enabled if a driver needs it.
Rename it to ALLOW_DEV_COREDUMP to better capture its semantics.
Aristeu Rozanski [Thu, 16 Oct 2014 15:49:49 +0000 (11:49 -0400)]
tiny: reverse logic for DISABLE_DEV_COREDUMP
It's desirable for allnconfig and tinyconfig targets to result in the
least amount of code possible. DISABLE_DEV_COREDUMP exists as a way to
switch off DEV_COREDUMP regardless if any drivers select
WANT_DEV_COREDUMP.
This patch renames the option to ENABLE_DEV_COREDUMP and setting it to
'n' (as in allnconfig or tinyconfig) will effectively disable device
coredump.
thermal: exynos: use correct offset for TMU_CONTROL register on Exynos5260
In exynos5260_tmu_registers tmu_ctrl entry is erroneously
assigned twice. The second assignment (to EXYNOS_TMU_REG_CONTROL1
define which represents 0x24 value) overrides the first one
(to EXYNOS_TMU_REG_CONTROL define which represents 0x20 value)
which results in the wrong (according to the Exynos5260 SoC
documentation that I have) offset being used for TMU_CONTROL
register. Fix it by removing the wrong assignment and then
remove no longer used EXYNOS_TMU_REG_CONTROL1 define.
Bai Ping [Tue, 14 Oct 2014 05:12:07 +0000 (13:12 +0800)]
thermal: imx: correct driver load sequence for cpu cooling
thermal driver should be regisetered after cpufreq driver has
been registered and probed. Doing so is to make sure that thermal
driver can get the max cpu cooling states correctly when calling
get_property.
Signed-off-by: Bai Ping <b51503@freescale.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Mark Knibbs [Tue, 4 Nov 2014 13:00:15 +0000 (13:00 +0000)]
USB: Update default usb-storage delay_use value in kernel-parameters.txt
Back in 2010 the default usb-storage delay_use time was reduced from 5 to 1
second (commit a4a47bc03fe520e95e0c4212bf97c86545fb14f9), but
kernel-parameters.txt wasn't updated to reflect that.
Signed-off-by: Mark Knibbs <markk@clara.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yijing Wang [Fri, 7 Nov 2014 04:05:49 +0000 (12:05 +0800)]
sysfs: driver core: Fix glue dir race condition by gdp_mutex
There is a race condition when removing glue directory.
It can be reproduced in following test:
path 1: Add first child device
device_add()
get_device_parent()
/*find parent from glue_dirs.list*/
list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry)
if (k->parent == parent_kobj) {
kobj = kobject_get(k);
break;
}
....
class_dir_create_and_add()
path2: Remove last child device under glue dir
device_del()
cleanup_device_parent()
cleanup_glue_dir()
kobject_put(glue_dir);
If path2 has been called cleanup_glue_dir(), but not
call kobject_put(glue_dir), the glue dir is still
in parent's kset list. Meanwhile, path1 find the glue
dir from the glue_dirs.list. Path2 may release glue dir
before path1 call kobject_get(). So kernel will report
the warning and bug_on.
This is a "classic" problem we have of a kref in a list
that can be found while the last instance could be removed
at the same time.
This patch reuse gdp_mutex to fix this race condition.
The following calltrace is captured in kernel 3.4, but
the latest kernel still has this bug.
Ping Cheng [Fri, 7 Nov 2014 01:30:51 +0000 (17:30 -0800)]
HID: wacom - make sure touch_input is valid before using it
touch_input is stored in wacom_shared for pen data to report touch
switch status. It is possible, although we didn't see it happen on
Linux yet, that pen data is procesed before touch interface is
fully probed.
As a by-product of this patch, it fixes the FreeBSD issue reported
by Denis Akiyakov http://www.spinics.net/lists/linux-input/msg33971.html
Manuel Lauss [Fri, 7 Nov 2014 13:13:54 +0000 (14:13 +0100)]
MIPS: Fix build with binutils 2.24.51+
Starting with version 2.24.51.20140728 MIPS binutils complain loudly
about mixing soft-float and hard-float object files, leading to this
build failure since GCC is invoked with "-msoft-float" on MIPS:
To fix this, we detect if GAS is new enough to support "-msoft-float" command
option, and if it does, we can let GCC pass it to GAS; but then we also need
to sprinkle the files which make use of floating point registers with the
necessary ".set hardfloat" directives.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Cc: Linux-MIPS <linux-mips@linux-mips.org> Cc: Matthew Fortune <Matthew.Fortune@imgtec.com> Cc: Markos Chandras <Markos.Chandras@imgtec.com> Cc: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8355/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dave Airlie [Fri, 7 Nov 2014 00:46:00 +0000 (10:46 +1000)]
Merge branch 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
- fix missing crtc unlock in MC setup
- set optimal CE ram config
- use gart rather than vram for DMA IB tests to avoid coherency issues with HDP
- fix a crasher with laptop mode and TDP scripts
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add missing crtc unlock when setting up the MC
drm/radeon: use gart for DMA IB tests
drm/radeon: make sure mode init is complete in bandwidth_update
drm/radeon: set correct CE ram size for CIK
projects / ~emulex / infiniband.git / log