From: Bruce Allan Date: Mon, 10 May 2010 15:02:32 +0000 (+0000) Subject: e1000e: Fix/cleanup PHY reset code for ICHx/PCHx X-Git-Tag: v2.6.35-rc1~473^2~132 X-Git-Url: https://openfabrics.org/gitweb/?a=commitdiff_plain;h=e98cac447cc1cc418dff1d610a5c79c4f2bdec7f;p=~emulex%2Finfiniband.git e1000e: Fix/cleanup PHY reset code for ICHx/PCHx i) Fixes a bug where e1000_sw_lcd_config_ich8lan() was calling e1000_lan_init_done_ich8lan() to poll the STATUS.LAN_INIT_DONE bit to make sure the MAC had completed the PHY configuration. However, e1000_lan_init_done_ich8lan() had already been called in one of the two places where PHY reset occurs for ICHx/PCHx parts, which caused the second call to busy-wait for 150 msec because the LAN_INIT_DONE bit had already been checked and cleared. ii) Cleanup the two separate PHY reset code paths, i.e. the full-chip reset in e1000_reset_hw_ich8lan() and the PHY-only reset in e1000_phy_hw_reset_ich8lan(). There was duplicate code in both paths to be performed post-reset that are now combined into one new function - e1000_post_phy_reset_ich8lan(). This cleanup also included moving the clearing of the PHY Reset Asserted bit in the STATUS register (now done for all ICH/PCH parts) and the check for the indication from h/w that basic configuration has completed back to where it previously was in e1000_get_cfg_done_ich8lan(). iii) Corrected a few comments Signed-off-by: Bruce Allan Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index 2b2cffc017b..10360fb596a 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -850,9 +850,6 @@ static s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw) if (!(data & sw_cfg_mask)) goto out; - /* Wait for basic configuration completes before proceeding */ - e1000_lan_init_done_ich8lan(hw); - /* * Make sure HW does not configure LCD from PHY * extended configuration before SW configuration @@ -1260,30 +1257,26 @@ static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw) } /** - * e1000_phy_hw_reset_ich8lan - Performs a PHY reset + * e1000_post_phy_reset_ich8lan - Perform steps required after a PHY reset * @hw: pointer to the HW structure - * - * Resets the PHY - * This is a function pointer entry point called by drivers - * or other shared routines. **/ -static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) +static s32 e1000_post_phy_reset_ich8lan(struct e1000_hw *hw) { s32 ret_val = 0; u16 reg; - ret_val = e1000e_phy_hw_reset_generic(hw); - if (ret_val) - return ret_val; - - /* Allow time for h/w to get to a quiescent state after reset */ - mdelay(10); + if (e1000_check_reset_block(hw)) + goto out; /* Perform any necessary post-reset workarounds */ - if (hw->mac.type == e1000_pchlan) { + switch (hw->mac.type) { + case e1000_pchlan: ret_val = e1000_hv_phy_workarounds_ich8lan(hw); if (ret_val) - return ret_val; + goto out; + break; + default: + break; } /* Dummy read to clear the phy wakeup bit after lcd reset */ @@ -1296,11 +1289,32 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) goto out; /* Configure the LCD with the OEM bits in NVM */ - if (hw->mac.type == e1000_pchlan) - ret_val = e1000_oem_bits_config_ich8lan(hw, true); + ret_val = e1000_oem_bits_config_ich8lan(hw, true); out: - return 0; + return ret_val; +} + +/** + * e1000_phy_hw_reset_ich8lan - Performs a PHY reset + * @hw: pointer to the HW structure + * + * Resets the PHY + * This is a function pointer entry point called by drivers + * or other shared routines. + **/ +static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) +{ + s32 ret_val = 0; + + ret_val = e1000e_phy_hw_reset_generic(hw); + if (ret_val) + goto out; + + ret_val = e1000_post_phy_reset_ich8lan(hw); + +out: + return ret_val; } /** @@ -2511,9 +2525,8 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) * on the last TLP read/write transaction when MAC is reset. */ ret_val = e1000e_disable_pcie_master(hw); - if (ret_val) { + if (ret_val) e_dbg("PCI-E Master disable polling has failed.\n"); - } e_dbg("Masking off all interrupts\n"); ew32(IMC, 0xffffffff); @@ -2552,14 +2565,8 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) ctrl = er32(CTRL); if (!e1000_check_reset_block(hw)) { - /* Clear PHY Reset Asserted bit */ - if (hw->mac.type >= e1000_pchlan) { - u32 status = er32(STATUS); - ew32(STATUS, status & ~E1000_STATUS_PHYRA); - } - /* - * PHY HW reset requires MAC CORE reset at the same + * Full-chip reset requires MAC and PHY reset at the same * time to make sure the interface between MAC and the * external PHY is reset. */ @@ -2573,39 +2580,16 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) if (!ret_val) e1000_release_swflag_ich8lan(hw); - /* Perform any necessary post-reset workarounds */ - if (hw->mac.type == e1000_pchlan) - ret_val = e1000_hv_phy_workarounds_ich8lan(hw); - - if (ctrl & E1000_CTRL_PHY_RST) + if (ctrl & E1000_CTRL_PHY_RST) { ret_val = hw->phy.ops.get_cfg_done(hw); + if (ret_val) + goto out; - if (hw->mac.type >= e1000_ich10lan) { - e1000_lan_init_done_ich8lan(hw); - } else { - ret_val = e1000e_get_auto_rd_done(hw); - if (ret_val) { - /* - * When auto config read does not complete, do not - * return with an error. This can happen in situations - * where there is no eeprom and prevents getting link. - */ - e_dbg("Auto Read Done did not complete\n"); - } - } - /* Dummy read to clear the phy wakeup bit after lcd reset */ - if (hw->mac.type == e1000_pchlan) - e1e_rphy(hw, BM_WUC, ®); - - ret_val = e1000_sw_lcd_config_ich8lan(hw); - if (ret_val) - goto out; - - if (hw->mac.type == e1000_pchlan) { - ret_val = e1000_oem_bits_config_ich8lan(hw, true); + ret_val = e1000_post_phy_reset_ich8lan(hw); if (ret_val) goto out; } + /* * For PCH, this write will make sure that any noise * will be detected as a CRC error and be dropped rather than show up @@ -3291,33 +3275,50 @@ static s32 e1000_led_off_pchlan(struct e1000_hw *hw) } /** - * e1000_get_cfg_done_ich8lan - Read config done bit + * e1000_get_cfg_done_ich8lan - Read config done bit after Full or PHY reset * @hw: pointer to the HW structure * - * Read the management control register for the config done bit for - * completion status. NOTE: silicon which is EEPROM-less will fail trying - * to read the config done bit, so an error is *ONLY* logged and returns - * 0. If we were to return with error, EEPROM-less silicon - * would not be able to be reset or change link. + * Read appropriate register for the config done bit for completion status + * and configure the PHY through s/w for EEPROM-less parts. + * + * NOTE: some silicon which is EEPROM-less will fail trying to read the + * config done bit, so only an error is logged and continues. If we were + * to return with error, EEPROM-less silicon would not be able to be reset + * or change link. **/ static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw) { + s32 ret_val = 0; u32 bank = 0; + u32 status; - if (hw->mac.type >= e1000_pchlan) { - u32 status = er32(STATUS); + e1000e_get_cfg_done(hw); - if (status & E1000_STATUS_PHYRA) - ew32(STATUS, status & ~E1000_STATUS_PHYRA); - else - e_dbg("PHY Reset Asserted not set - needs delay\n"); + /* Wait for indication from h/w that it has completed basic config */ + if (hw->mac.type >= e1000_ich10lan) { + e1000_lan_init_done_ich8lan(hw); + } else { + ret_val = e1000e_get_auto_rd_done(hw); + if (ret_val) { + /* + * When auto config read does not complete, do not + * return with an error. This can happen in situations + * where there is no eeprom and prevents getting link. + */ + e_dbg("Auto Read Done did not complete\n"); + ret_val = 0; + } } - e1000e_get_cfg_done(hw); + /* Clear PHY Reset Asserted bit */ + status = er32(STATUS); + if (status & E1000_STATUS_PHYRA) + ew32(STATUS, status & ~E1000_STATUS_PHYRA); + else + e_dbg("PHY Reset Asserted not set - needs delay\n"); /* If EEPROM is not marked present, init the IGP 3 PHY manually */ - if ((hw->mac.type != e1000_ich10lan) && - (hw->mac.type != e1000_pchlan)) { + if (hw->mac.type <= e1000_ich9lan) { if (((er32(EECD) & E1000_EECD_PRES) == 0) && (hw->phy.type == e1000_phy_igp_3)) { e1000e_phy_init_script_igp3(hw); @@ -3326,11 +3327,11 @@ static s32 e1000_get_cfg_done_ich8lan(struct e1000_hw *hw) if (e1000_valid_nvm_bank_detect_ich8lan(hw, &bank)) { /* Maybe we should do a basic PHY config */ e_dbg("EEPROM not present\n"); - return -E1000_ERR_CONFIG; + ret_val = -E1000_ERR_CONFIG; } } - return 0; + return ret_val; } /**