From: Finn Thain Date: Wed, 12 Nov 2014 05:11:55 +0000 (+1100) Subject: ncr5380: Remove duplicate comments X-Git-Tag: v3.19-rc1~176^2^2~85 X-Git-Url: https://openfabrics.org/gitweb/?a=commitdiff_plain;h=3f9e986e2f1df8fa69ffe213098c1ee98f1c9584;p=~emulex%2Finfiniband.git ncr5380: Remove duplicate comments The LIMIT_TRANSFERSIZE, PSEUDO_DMA, PARITY and UNSAFE options are all documented in the core drivers where they are used. The same goes for the chip databook reference. Remove the duplicate comments. Signed-off-by: Finn Thain Reviewed-by: Hannes Reinecke Signed-off-by: Christoph Hellwig --- diff --git a/drivers/scsi/dtc.c b/drivers/scsi/dtc.c index 975abbfe0bb..43be785778d 100644 --- a/drivers/scsi/dtc.c +++ b/drivers/scsi/dtc.c @@ -19,24 +19,9 @@ * +1 (303) 440-4894 * * DISTRIBUTION RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook -*/ + */ /* - * Options : - * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance - * increase compared to polled I/O. - * - * PARITY - enable parity checking. Not supported. - * - * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. - * You probably want this. - * * The card is detected and initialized in one of several ways : * 1. Autoprobe (default) - since the board is memory mapped, * a BIOS signature is scanned for to locate the registers. diff --git a/drivers/scsi/dtc.h b/drivers/scsi/dtc.h index b96252ac641..46ad3403bda 100644 --- a/drivers/scsi/dtc.h +++ b/drivers/scsi/dtc.h @@ -7,22 +7,6 @@ * +1 (303) 440-4894 * * DISTRIBUTION RELEASE 2. - * - * For more information, please consult - * - * - * - * and - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #ifndef DTC3280_H diff --git a/drivers/scsi/g_NCR5380.c b/drivers/scsi/g_NCR5380.c index eda978f29d9..151e1ad8fe9 100644 --- a/drivers/scsi/g_NCR5380.c +++ b/drivers/scsi/g_NCR5380.c @@ -20,18 +20,6 @@ * Thomas Sailer, sailer@ife.ee.ethz.ch * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ /* @@ -40,10 +28,6 @@ */ /* - * Options : - * - * PARITY - enable parity checking. Not supported. - * * The card is detected and initialized in one of several ways : * 1. With command line overrides - NCR5380=port,irq may be * used on the LILO command line to override the defaults. diff --git a/drivers/scsi/g_NCR5380.h b/drivers/scsi/g_NCR5380.h index 75e7e498326..e15b95c3786 100644 --- a/drivers/scsi/g_NCR5380.h +++ b/drivers/scsi/g_NCR5380.h @@ -11,18 +11,6 @@ * K.Lentin@cs.monash.edu.au * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #ifndef GENERIC_NCR5380_H diff --git a/drivers/scsi/mac_scsi.c b/drivers/scsi/mac_scsi.c index 3f125838a29..4dec06da3f3 100644 --- a/drivers/scsi/mac_scsi.c +++ b/drivers/scsi/mac_scsi.c @@ -11,18 +11,6 @@ * Copyright 1995, Russell King * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #include diff --git a/drivers/scsi/mac_scsi.h b/drivers/scsi/mac_scsi.h index c86ced5b56d..0b123fe9c24 100644 --- a/drivers/scsi/mac_scsi.h +++ b/drivers/scsi/mac_scsi.h @@ -8,18 +8,6 @@ * +1 (303) 440-4894 * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #ifndef MAC_NCR5380_H diff --git a/drivers/scsi/pas16.c b/drivers/scsi/pas16.c index 7621205e4aa..3e40479ebb4 100644 --- a/drivers/scsi/pas16.c +++ b/drivers/scsi/pas16.c @@ -22,40 +22,9 @@ * Media Vision * (510) 770-8600 * (800) 348-7116 - * - * and - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ /* - * Options : - * LIMIT_TRANSFERSIZE - if defined, limit the pseudo-dma transfers to 512 - * bytes at a time. Since interrupts are disabled by default during - * these transfers, we might need this to give reasonable interrupt - * service time if the transfer size gets too large. - * - * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance - * increase compared to polled I/O. - * - * PARITY - enable parity checking. Not supported. - * - * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. This - * parameter comes from the NCR5380 code. It is NOT unsafe with - * the PAS16 and you should use it. If you don't you will have - * a problem with dropped characters during high speed - * communications during SCSI transfers. If you really don't - * want to use UNSAFE you can try defining LIMIT_TRANSFERSIZE or - * twiddle with the transfer size in the high level code. - * * The card is detected and initialized in one of several ways : * 1. Autoprobe (default) - There are many different models of * the Pro Audio Spectrum/Studio 16, and I only have one of diff --git a/drivers/scsi/pas16.h b/drivers/scsi/pas16.h index 772c4e0eee4..489acb5bf29 100644 --- a/drivers/scsi/pas16.h +++ b/drivers/scsi/pas16.h @@ -18,18 +18,6 @@ * Media Vision * (510) 770-8600 * (800) 348-7116 - * - * and - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ diff --git a/drivers/scsi/sun3_scsi.c b/drivers/scsi/sun3_scsi.c index a5e58a7373b..26b95dcb5e4 100644 --- a/drivers/scsi/sun3_scsi.c +++ b/drivers/scsi/sun3_scsi.c @@ -22,27 +22,6 @@ * Copyright 1995, Russell King * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 - */ - - -/* - * This is from mac_scsi.h, but hey, maybe this is useful for Sun3 too! :) - * - * Options : - * - * PARITY - enable parity checking. Not supported. */ #include diff --git a/drivers/scsi/sun3_scsi.h b/drivers/scsi/sun3_scsi.h index b3163a5f11c..cb9d2a48840 100644 --- a/drivers/scsi/sun3_scsi.h +++ b/drivers/scsi/sun3_scsi.h @@ -15,18 +15,6 @@ * +1 (303) 440-4894 * * ALPHA RELEASE 1. - * - * For more information, please consult - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #ifndef SUN3_SCSI_H diff --git a/drivers/scsi/t128.c b/drivers/scsi/t128.c index 4253fe97c21..6220dee8b69 100644 --- a/drivers/scsi/t128.c +++ b/drivers/scsi/t128.c @@ -23,32 +23,9 @@ * 5415 Randall Place * Fremont, CA 94538 * 1+ (415) 770-1400, FAX 1+ (415) 770-9910 - * - * and - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ /* - * Options : - * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance - * increase compared to polled I/O. - * - * PARITY - enable parity checking. Not supported. - * - * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. You - * only really want to use this if you're having a problem with - * dropped characters during high speed communications, and even - * then, you're going to be better off twiddling with transfersize. - * * The card is detected and initialized in one of several ways : * 1. Autoprobe (default) - since the board is memory mapped, * a BIOS signature is scanned for to locate the registers. diff --git a/drivers/scsi/t128.h b/drivers/scsi/t128.h index 82959ed89a1..9f06c185106 100644 --- a/drivers/scsi/t128.h +++ b/drivers/scsi/t128.h @@ -20,18 +20,6 @@ * 5415 Randall Place * Fremont, CA 94538 * 1+ (415) 770-1400, FAX 1+ (415) 770-9910 - * - * and - * - * NCR 5380 Family - * SCSI Protocol Controller - * Databook - * - * NCR Microelectronics - * 1635 Aeroplaza Drive - * Colorado Springs, CO 80916 - * 1+ (719) 578-3400 - * 1+ (800) 334-5454 */ #ifndef T128_H