From: H Hartley Sweeten <hsweeten@visionengravers.com>
Date: Mon, 17 Feb 2014 21:27:57 +0000 (-0700)
Subject: staging: comedi: pcl818: tidy up pcl818_check()
X-Git-Tag: v3.15-rc1~139^2~932
X-Git-Url: https://openfabrics.org/gitweb/?a=commitdiff_plain;h=243e7146c8ed16cbda71126168fe73acab7c62d2;p=~emulex%2Finfiniband.git

staging: comedi: pcl818: tidy up pcl818_check()

This function probes a number of the boards registers during the
(*attach) to verify that it is actually a PCL-818 compatible board.
For aesthetics, move the function closer to the (*attach).

Refactor the function to return an errno if fails. Change the errno
from -EIO to -ENODEV and remove the unnecessary comedi_error() noise.

Make sure the CONTROL register is reset to a known state after the
check. The 0x18 value actually defines an invalid interrupt selection
and sets an undefined bit.

Add a couple comments to clarify the magic values.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---

diff --git a/drivers/staging/comedi/drivers/pcl818.c b/drivers/staging/comedi/drivers/pcl818.c
index 65101970f99..56a5de712e8 100644
--- a/drivers/staging/comedi/drivers/pcl818.c
+++ b/drivers/staging/comedi/drivers/pcl818.c
@@ -1082,25 +1082,6 @@ end:
 	return 0;
 }
 
-static int pcl818_check(unsigned long iobase)
-{
-	outb(0x00, iobase + PCL818_MUX);
-	udelay(1);
-	if (inb(iobase + PCL818_MUX) != 0x00)
-		return 1;	/* there isn't card */
-	outb(0x55, iobase + PCL818_MUX);
-	udelay(1);
-	if (inb(iobase + PCL818_MUX) != 0x55)
-		return 1;	/* there isn't card */
-	outb(0x00, iobase + PCL818_MUX);
-	udelay(1);
-	outb(0x18, iobase + PCL818_CONTROL);
-	udelay(1);
-	if (inb(iobase + PCL818_CONTROL) != 0x18)
-		return 1;	/* there isn't card */
-	return 0;		/*  ok, card exist */
-}
-
 static void pcl818_reset(struct comedi_device *dev)
 {
 	const struct pcl818_board *board = comedi_board(dev);
@@ -1187,6 +1168,30 @@ static void pcl818_set_ai_range_table(struct comedi_device *dev,
 	}
 }
 
+static int pcl818_check(struct comedi_device *dev)
+{
+	/* the MUX register should return the same value written */
+	outb(0x00, dev->iobase + PCL818_MUX);
+	if (inb(dev->iobase + PCL818_MUX) != 0x00)
+		return -ENODEV;
+	outb(0x55, dev->iobase + PCL818_MUX);
+	if (inb(dev->iobase + PCL818_MUX) != 0x55)
+		return -ENODEV;
+
+	/* reset the MUX register to a known state */
+	outb(0x00, dev->iobase + PCL818_MUX);
+
+	/* the CONTROL register should return the same value written */
+	outb(0x18, dev->iobase + PCL818_CONTROL);
+	if (inb(dev->iobase + PCL818_CONTROL) != 0x18)
+		return -ENODEV;
+
+	/* reset the CONTROL register to a known state */
+	outb(0x00, dev->iobase + PCL818_CONTROL);
+
+	return 0;
+}
+
 static int pcl818_attach(struct comedi_device *dev, struct comedi_devconfig *it)
 {
 	const struct pcl818_board *board = comedi_board(dev);
@@ -1208,10 +1213,9 @@ static int pcl818_attach(struct comedi_device *dev, struct comedi_devconfig *it)
 	if (ret)
 		return ret;
 
-	if (pcl818_check(dev->iobase)) {
-		comedi_error(dev, "I can't detect board. FAIL!\n");
-		return -EIO;
-	}
+	ret = pcl818_check(dev);
+	if (ret)
+		return ret;
 
 	/* we can use IRQ 2-7 for async command support */
 	if (it->options[1] >= 2 && it->options[1] <= 7) {