dmaengine/amba-pl08x: max_bytes_per_lli is TRANSFER_SIZE * src_width (not MIN(width))

max_bytes_per_lli = bd.srcbus.buswidth * PL080_CONTROL_TRANSFER_SIZE_MASK;
This is confirmed by ARM support guys.

Below is summary of mail exchange with them:

[Viresh] What is the total data to be transferred in case source and destination
bus widths are different. Suppose, source bus width is 2 bytes and destination
is 4 bytes. Now in order to transfer 80 bytes, what should be value of
TransferSize field in control reg: 40? or 20?.

[David from ARM] The value that is programmed into the TransferSize field should
be the number of <SourceWidth> transfers needed to achieve the required data
transfer.

So, to transfer 80 bytes, with a Source Width of 2, the TransferSize field =
should be programmed with:

        Total transfer size
        ------------------- = 40
          <source width>

[Viresh] Will this change if source is 4 bytes and dest is 2?

[David] Yes - the calculation then becomes:

        Total transfer size
        ------------------- =20
          <source width>

Also, max_bytes_per_lli must be calculated after fixing src and dest widths not
before that. So move this code to the correct place.

This patch also removes max_bytes_per_lli from earlier print message, as till
that point max_bytes_per_lli is unknown.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

diff --git a/drivers/dma/amba-pl08x.c b/drivers/dma/amba-pl08x.c
index be9a1c718f9a8992c2d26c738c8e407389454ed8..e5930d512b00deb0bdb6adf66199e83a65121131 100644 (file)
--- a/drivers/dma/amba-pl08x.c
+++ b/drivers/dma/amba-pl08x.c
@@ -604,23 +604,17 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
        bd.srcbus.buswidth = bd.srcbus.maxwidth;
        bd.dstbus.buswidth = bd.dstbus.maxwidth;
 
-       /*
-        * Bytes transferred == tsize * MIN(buswidths), not max(buswidths)
-        */
-       max_bytes_per_lli = min(bd.srcbus.buswidth, bd.dstbus.buswidth) *
-               PL080_CONTROL_TRANSFER_SIZE_MASK;
-
        /* We need to count this down to zero */
        bd.remainder = txd->len;
 
        pl08x_choose_master_bus(&bd, &mbus, &sbus, cctl);
 
-       dev_vdbg(&pl08x->adev->dev, "src=0x%08x%s/%u dst=0x%08x%s/%u len=%zu llimax=%zu\n",
+       dev_vdbg(&pl08x->adev->dev, "src=0x%08x%s/%u dst=0x%08x%s/%u len=%zu\n",
                 bd.srcbus.addr, cctl & PL080_CONTROL_SRC_INCR ? "+" : "",
                 bd.srcbus.buswidth,
                 bd.dstbus.addr, cctl & PL080_CONTROL_DST_INCR ? "+" : "",
                 bd.dstbus.buswidth,
-                bd.remainder, max_bytes_per_lli);
+                bd.remainder);
        dev_vdbg(&pl08x->adev->dev, "mbus=%s sbus=%s\n",
                 mbus == &bd.srcbus ? "src" : "dst",
                 sbus == &bd.srcbus ? "src" : "dst");
@@ -660,6 +654,10 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
                        sbus->buswidth = 1;
                }
 
+               /* Bytes transferred = tsize * src width, not MIN(buswidths) */
+               max_bytes_per_lli = bd.srcbus.buswidth *
+                       PL080_CONTROL_TRANSFER_SIZE_MASK;
+
                /*
                 * Make largest possible LLIs until less than one bus
                 * width left