* - Other minor stuff
*
* v1.4 Feb 10, 2000 - Updated with more changes required after Dave's
- * network cleanup in 2.3.43pre7 (Tigran & myself)
- * - Minor stuff.
+ * network cleanup in 2.3.43pre7 (Tigran & myself)
+ * - Minor stuff.
*
- * v1.5 March 22, 2000 - Fixed another timer bug that would hang the driver
- * if no cable/link were present.
+ * v1.5 March 22, 2000 - Fixed another timer bug that would hang the
+ * driver if no cable/link were present.
* - Cosmetic changes.
* - TODO: Port completely to new PCI/DMA API
- * Auto-Neg fallback.
- *
- * v1.6 April 04, 2000 - Fixed driver support for kernel-parameters. Haven't
- * tested it though, as the kernel support is currently
- * broken (2.3.99p4p3).
- * - Updated tlan.txt accordingly.
- * - Adjusted minimum/maximum frame length.
- * - There is now a TLAN website up at
- * http://hp.sourceforge.net/
- *
- * v1.7 April 07, 2000 - Started to implement custom ioctls. Driver now
- * reports PHY information when used with Donald
- * Beckers userspace MII diagnostics utility.
- *
- * v1.8 April 23, 2000 - Fixed support for forced speed/duplex settings.
- * - Added link information to Auto-Neg and forced
- * modes. When NIC operates with auto-neg the driver
- * will report Link speed & duplex modes as well as
- * link partner abilities. When forced link is used,
- * the driver will report status of the established
- * link.
- * Please read tlan.txt for additional information.
- * - Removed call to check_region(), and used
- * return value of request_region() instead.
+ * Auto-Neg fallback.
+ *
+ * v1.6 April 04, 2000 - Fixed driver support for kernel-parameters.
+ * Haven't tested it though, as the kernel support
+ * is currently broken (2.3.99p4p3).
+ * - Updated tlan.txt accordingly.
+ * - Adjusted minimum/maximum frame length.
+ * - There is now a TLAN website up at
+ * http://hp.sourceforge.net/
+ *
+ * v1.7 April 07, 2000 - Started to implement custom ioctls. Driver now
+ * reports PHY information when used with Donald
+ * Beckers userspace MII diagnostics utility.
+ *
+ * v1.8 April 23, 2000 - Fixed support for forced speed/duplex settings.
+ * - Added link information to Auto-Neg and forced
+ * modes. When NIC operates with auto-neg the driver
+ * will report Link speed & duplex modes as well as
+ * link partner abilities. When forced link is used,
+ * the driver will report status of the established
+ * link.
+ * Please read tlan.txt for additional information.
+ * - Removed call to check_region(), and used
+ * return value of request_region() instead.
*
* v1.8a May 28, 2000 - Minor updates.
*
* v1.9 July 25, 2000 - Fixed a few remaining Full-Duplex issues.
- * - Updated with timer fixes from Andrew Morton.
- * - Fixed module race in TLan_Open.
- * - Added routine to monitor PHY status.
- * - Added activity led support for Proliant devices.
+ * - Updated with timer fixes from Andrew Morton.
+ * - Fixed module race in TLan_Open.
+ * - Added routine to monitor PHY status.
+ * - Added activity led support for Proliant devices.
*
* v1.10 Aug 30, 2000 - Added support for EISA based tlan controllers
* like the Compaq NetFlex3/E.
* hardware probe is done with kernel API and
* TLan_EisaProbe.
* - Adjusted debug information for probing.
- * - Fixed bug that would cause general debug information
- * to be printed after driver removal.
+ * - Fixed bug that would cause general debug
+ * information to be printed after driver removal.
* - Added transmit timeout handling.
* - Fixed OOM return values in tlan_probe.
* - Fixed possible mem leak in tlan_exit
*
* v1.12 Oct 12, 2000 - Minor fixes (memleak, init, etc.)
*
- * v1.13 Nov 28, 2000 - Stop flooding console with auto-neg issues
- * when link can't be established.
+ * v1.13 Nov 28, 2000 - Stop flooding console with auto-neg issues
+ * when link can't be established.
* - Added the bbuf option as a kernel parameter.
* - Fixed ioaddr probe bug.
* - Fixed stupid deadlock with MII interrupts.
* TLAN v1.0 silicon. This needs to be investigated
* further.
*
- * v1.14 Dec 16, 2000 - Added support for servicing multiple frames per.
- * interrupt. Thanks goes to
- * Adam Keys <adam@ti.com>
- * Denis Beaudoin <dbeaudoin@ti.com>
- * for providing the patch.
- * - Fixed auto-neg output when using multiple
- * adapters.
- * - Converted to use new taskq interface.
+ * v1.14 Dec 16, 2000 - Added support for servicing multiple frames per.
+ * interrupt. Thanks goes to
+ * Adam Keys <adam@ti.com>
+ * Denis Beaudoin <dbeaudoin@ti.com>
+ * for providing the patch.
+ * - Fixed auto-neg output when using multiple
+ * adapters.
+ * - Converted to use new taskq interface.
*
- * v1.14a Jan 6, 2001 - Minor adjustments (spinlocks, etc.)
+ * v1.14a Jan 6, 2001 - Minor adjustments (spinlocks, etc.)
*
* Samuel Chessman <chessman@tux.org> New Maintainer!
*
* v1.15 Apr 4, 2002 - Correct operation when aui=1 to be
- * 10T half duplex no loopback
- * Thanks to Gunnar Eikman
+ * 10T half duplex no loopback
+ * Thanks to Gunnar Eikman
*
* Sakari Ailus <sakari.ailus@iki.fi>:
*
* v1.15a Dec 15 2008 - Remove bbuf support, it doesn't work anyway.
+ * v1.16 Jan 6 2011 - Make checkpatch.pl happy.
*
- *******************************************************************************/
+ ******************************************************************************/
#include <linux/module.h>
#include <linux/init.h>
#include "tlan.h"
-typedef u32 (TLanIntVectorFunc)( struct net_device *, u16 );
-
/* For removing EISA devices */
-static struct net_device *TLan_Eisa_Devices;
+static struct net_device *tlan_eisa_devices;
-static int TLanDevicesInstalled;
+static int tlan_devices_installed;
/* Set speed, duplex and aui settings */
static int aui[MAX_TLAN_BOARDS];
module_param_array(duplex, int, NULL, 0);
module_param_array(speed, int, NULL, 0);
MODULE_PARM_DESC(aui, "ThunderLAN use AUI port(s) (0-1)");
-MODULE_PARM_DESC(duplex, "ThunderLAN duplex setting(s) (0-default, 1-half, 2-full)");
+MODULE_PARM_DESC(duplex,
+ "ThunderLAN duplex setting(s) (0-default, 1-half, 2-full)");
MODULE_PARM_DESC(speed, "ThunderLAN port speen setting(s) (0,10,100)");
MODULE_AUTHOR("Maintainer: Samuel Chessman <chessman@tux.org>");
module_param(debug, int, 0);
MODULE_PARM_DESC(debug, "ThunderLAN debug mask");
-static const char TLanSignature[] = "TLAN";
-static const char tlan_banner[] = "ThunderLAN driver v1.15a\n";
+static const char tlan_signature[] = "TLAN";
+static const char tlan_banner[] = "ThunderLAN driver v1.16\n";
static int tlan_have_pci;
static int tlan_have_eisa;
-static const char *media[] = {
- "10BaseT-HD ", "10BaseT-FD ","100baseTx-HD ",
- "100baseTx-FD", "100baseT4", NULL
+static const char * const media[] = {
+ "10BaseT-HD", "10BaseT-FD", "100baseTx-HD",
+ "100BaseTx-FD", "100BaseT4", NULL
};
static struct board {
- const char *deviceLabel;
- u32 flags;
- u16 addrOfs;
+ const char *device_label;
+ u32 flags;
+ u16 addr_ofs;
} board_info[] = {
{ "Compaq Netelligent 10 T PCI UTP", TLAN_ADAPTER_ACTIVITY_LED, 0x83 },
- { "Compaq Netelligent 10/100 TX PCI UTP", TLAN_ADAPTER_ACTIVITY_LED, 0x83 },
+ { "Compaq Netelligent 10/100 TX PCI UTP",
+ TLAN_ADAPTER_ACTIVITY_LED, 0x83 },
{ "Compaq Integrated NetFlex-3/P", TLAN_ADAPTER_NONE, 0x83 },
{ "Compaq NetFlex-3/P",
TLAN_ADAPTER_UNMANAGED_PHY | TLAN_ADAPTER_BIT_RATE_PHY, 0x83 },
{ "Compaq NetFlex-3/P", TLAN_ADAPTER_NONE, 0x83 },
{ "Compaq Netelligent Integrated 10/100 TX UTP",
TLAN_ADAPTER_ACTIVITY_LED, 0x83 },
- { "Compaq Netelligent Dual 10/100 TX PCI UTP", TLAN_ADAPTER_NONE, 0x83 },
- { "Compaq Netelligent 10/100 TX Embedded UTP", TLAN_ADAPTER_NONE, 0x83 },
+ { "Compaq Netelligent Dual 10/100 TX PCI UTP",
+ TLAN_ADAPTER_NONE, 0x83 },
+ { "Compaq Netelligent 10/100 TX Embedded UTP",
+ TLAN_ADAPTER_NONE, 0x83 },
{ "Olicom OC-2183/2185", TLAN_ADAPTER_USE_INTERN_10, 0x83 },
- { "Olicom OC-2325", TLAN_ADAPTER_UNMANAGED_PHY, 0xF8 },
- { "Olicom OC-2326", TLAN_ADAPTER_USE_INTERN_10, 0xF8 },
+ { "Olicom OC-2325", TLAN_ADAPTER_UNMANAGED_PHY, 0xf8 },
+ { "Olicom OC-2326", TLAN_ADAPTER_USE_INTERN_10, 0xf8 },
{ "Compaq Netelligent 10/100 TX UTP", TLAN_ADAPTER_ACTIVITY_LED, 0x83 },
- { "Compaq Netelligent 10 T/2 PCI UTP/Coax", TLAN_ADAPTER_NONE, 0x83 },
+ { "Compaq Netelligent 10 T/2 PCI UTP/coax", TLAN_ADAPTER_NONE, 0x83 },
{ "Compaq NetFlex-3/E",
- TLAN_ADAPTER_ACTIVITY_LED | /* EISA card */
+ TLAN_ADAPTER_ACTIVITY_LED | /* EISA card */
TLAN_ADAPTER_UNMANAGED_PHY | TLAN_ADAPTER_BIT_RATE_PHY, 0x83 },
- { "Compaq NetFlex-3/E", TLAN_ADAPTER_ACTIVITY_LED, 0x83 }, /* EISA card */
+ { "Compaq NetFlex-3/E",
+ TLAN_ADAPTER_ACTIVITY_LED, 0x83 }, /* EISA card */
};
static DEFINE_PCI_DEVICE_TABLE(tlan_pci_tbl) = {
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_NETEL10,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_NETEL100,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1 },
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_NETFLEX3I,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2 },
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_THUNDER,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3 },
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_NETFLEX3B,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4 },
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_NETEL100PI,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5 },
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_NETEL100D,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 6 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 6 },
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_COMPAQ_NETEL100I,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7 },
{ PCI_VENDOR_ID_OLICOM, PCI_DEVICE_ID_OLICOM_OC2183,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8 },
{ PCI_VENDOR_ID_OLICOM, PCI_DEVICE_ID_OLICOM_OC2325,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9 },
{ PCI_VENDOR_ID_OLICOM, PCI_DEVICE_ID_OLICOM_OC2326,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 10 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 10 },
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_NETELLIGENT_10_100_WS_5100,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 11 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 11 },
{ PCI_VENDOR_ID_COMPAQ, PCI_DEVICE_ID_NETELLIGENT_10_T2,
- PCI_ANY_ID, PCI_ANY_ID, 0, 0, 12 },
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 12 },
{ 0,}
};
MODULE_DEVICE_TABLE(pci, tlan_pci_tbl);
-static void TLan_EisaProbe( void );
-static void TLan_Eisa_Cleanup( void );
-static int TLan_Init( struct net_device * );
-static int TLan_Open( struct net_device *dev );
-static netdev_tx_t TLan_StartTx( struct sk_buff *, struct net_device *);
-static irqreturn_t TLan_HandleInterrupt( int, void *);
-static int TLan_Close( struct net_device *);
-static struct net_device_stats *TLan_GetStats( struct net_device *);
-static void TLan_SetMulticastList( struct net_device *);
-static int TLan_ioctl( struct net_device *dev, struct ifreq *rq, int cmd);
-static int TLan_probe1( struct pci_dev *pdev, long ioaddr,
- int irq, int rev, const struct pci_device_id *ent);
-static void TLan_tx_timeout( struct net_device *dev);
-static void TLan_tx_timeout_work(struct work_struct *work);
-static int tlan_init_one( struct pci_dev *pdev, const struct pci_device_id *ent);
-
-static u32 TLan_HandleTxEOF( struct net_device *, u16 );
-static u32 TLan_HandleStatOverflow( struct net_device *, u16 );
-static u32 TLan_HandleRxEOF( struct net_device *, u16 );
-static u32 TLan_HandleDummy( struct net_device *, u16 );
-static u32 TLan_HandleTxEOC( struct net_device *, u16 );
-static u32 TLan_HandleStatusCheck( struct net_device *, u16 );
-static u32 TLan_HandleRxEOC( struct net_device *, u16 );
-
-static void TLan_Timer( unsigned long );
-
-static void TLan_ResetLists( struct net_device * );
-static void TLan_FreeLists( struct net_device * );
-static void TLan_PrintDio( u16 );
-static void TLan_PrintList( TLanList *, char *, int );
-static void TLan_ReadAndClearStats( struct net_device *, int );
-static void TLan_ResetAdapter( struct net_device * );
-static void TLan_FinishReset( struct net_device * );
-static void TLan_SetMac( struct net_device *, int areg, char *mac );
-
-static void TLan_PhyPrint( struct net_device * );
-static void TLan_PhyDetect( struct net_device * );
-static void TLan_PhyPowerDown( struct net_device * );
-static void TLan_PhyPowerUp( struct net_device * );
-static void TLan_PhyReset( struct net_device * );
-static void TLan_PhyStartLink( struct net_device * );
-static void TLan_PhyFinishAutoNeg( struct net_device * );
+static void tlan_eisa_probe(void);
+static void tlan_eisa_cleanup(void);
+static int tlan_init(struct net_device *);
+static int tlan_open(struct net_device *dev);
+static netdev_tx_t tlan_start_tx(struct sk_buff *, struct net_device *);
+static irqreturn_t tlan_handle_interrupt(int, void *);
+static int tlan_close(struct net_device *);
+static struct net_device_stats *tlan_get_stats(struct net_device *);
+static void tlan_set_multicast_list(struct net_device *);
+static int tlan_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
+static int tlan_probe1(struct pci_dev *pdev, long ioaddr,
+ int irq, int rev, const struct pci_device_id *ent);
+static void tlan_tx_timeout(struct net_device *dev);
+static void tlan_tx_timeout_work(struct work_struct *work);
+static int tlan_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent);
+
+static u32 tlan_handle_tx_eof(struct net_device *, u16);
+static u32 tlan_handle_stat_overflow(struct net_device *, u16);
+static u32 tlan_handle_rx_eof(struct net_device *, u16);
+static u32 tlan_handle_dummy(struct net_device *, u16);
+static u32 tlan_handle_tx_eoc(struct net_device *, u16);
+static u32 tlan_handle_status_check(struct net_device *, u16);
+static u32 tlan_handle_rx_eoc(struct net_device *, u16);
+
+static void tlan_timer(unsigned long);
+
+static void tlan_reset_lists(struct net_device *);
+static void tlan_free_lists(struct net_device *);
+static void tlan_print_dio(u16);
+static void tlan_print_list(struct tlan_list *, char *, int);
+static void tlan_read_and_clear_stats(struct net_device *, int);
+static void tlan_reset_adapter(struct net_device *);
+static void tlan_finish_reset(struct net_device *);
+static void tlan_set_mac(struct net_device *, int areg, char *mac);
+
+static void tlan_phy_print(struct net_device *);
+static void tlan_phy_detect(struct net_device *);
+static void tlan_phy_power_down(struct net_device *);
+static void tlan_phy_power_up(struct net_device *);
+static void tlan_phy_reset(struct net_device *);
+static void tlan_phy_start_link(struct net_device *);
+static void tlan_phy_finish_auto_neg(struct net_device *);
#ifdef MONITOR
-static void TLan_PhyMonitor( struct net_device * );
+static void tlan_phy_monitor(struct net_device *);
#endif
/*
-static int TLan_PhyNop( struct net_device * );
-static int TLan_PhyInternalCheck( struct net_device * );
-static int TLan_PhyInternalService( struct net_device * );
-static int TLan_PhyDp83840aCheck( struct net_device * );
+ static int tlan_phy_nop(struct net_device *);
+ static int tlan_phy_internal_check(struct net_device *);
+ static int tlan_phy_internal_service(struct net_device *);
+ static int tlan_phy_dp83840a_check(struct net_device *);
*/
-static bool TLan_MiiReadReg( struct net_device *, u16, u16, u16 * );
-static void TLan_MiiSendData( u16, u32, unsigned );
-static void TLan_MiiSync( u16 );
-static void TLan_MiiWriteReg( struct net_device *, u16, u16, u16 );
+static bool tlan_mii_read_reg(struct net_device *, u16, u16, u16 *);
+static void tlan_mii_send_data(u16, u32, unsigned);
+static void tlan_mii_sync(u16);
+static void tlan_mii_write_reg(struct net_device *, u16, u16, u16);
-static void TLan_EeSendStart( u16 );
-static int TLan_EeSendByte( u16, u8, int );
-static void TLan_EeReceiveByte( u16, u8 *, int );
-static int TLan_EeReadByte( struct net_device *, u8, u8 * );
+static void tlan_ee_send_start(u16);
+static int tlan_ee_send_byte(u16, u8, int);
+static void tlan_ee_receive_byte(u16, u8 *, int);
+static int tlan_ee_read_byte(struct net_device *, u8, u8 *);
static inline void
-TLan_StoreSKB( struct tlan_list_tag *tag, struct sk_buff *skb)
+tlan_store_skb(struct tlan_list *tag, struct sk_buff *skb)
{
unsigned long addr = (unsigned long)skb;
tag->buffer[9].address = addr;
}
static inline struct sk_buff *
-TLan_GetSKB( const struct tlan_list_tag *tag)
+tlan_get_skb(const struct tlan_list *tag)
{
unsigned long addr;
return (struct sk_buff *) addr;
}
-
-static TLanIntVectorFunc *TLanIntVector[TLAN_INT_NUMBER_OF_INTS] = {
+static u32
+(*tlan_int_vector[TLAN_INT_NUMBER_OF_INTS])(struct net_device *, u16) = {
NULL,
- TLan_HandleTxEOF,
- TLan_HandleStatOverflow,
- TLan_HandleRxEOF,
- TLan_HandleDummy,
- TLan_HandleTxEOC,
- TLan_HandleStatusCheck,
- TLan_HandleRxEOC
+ tlan_handle_tx_eof,
+ tlan_handle_stat_overflow,
+ tlan_handle_rx_eof,
+ tlan_handle_dummy,
+ tlan_handle_tx_eoc,
+ tlan_handle_status_check,
+ tlan_handle_rx_eoc
};
static inline void
-TLan_SetTimer( struct net_device *dev, u32 ticks, u32 type )
+tlan_set_timer(struct net_device *dev, u32 ticks, u32 type)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
unsigned long flags = 0;
if (!in_irq())
spin_lock_irqsave(&priv->lock, flags);
- if ( priv->timer.function != NULL &&
- priv->timerType != TLAN_TIMER_ACTIVITY ) {
+ if (priv->timer.function != NULL &&
+ priv->timer_type != TLAN_TIMER_ACTIVITY) {
if (!in_irq())
spin_unlock_irqrestore(&priv->lock, flags);
return;
}
- priv->timer.function = TLan_Timer;
+ priv->timer.function = tlan_timer;
if (!in_irq())
spin_unlock_irqrestore(&priv->lock, flags);
priv->timer.data = (unsigned long) dev;
- priv->timerSetAt = jiffies;
- priv->timerType = type;
+ priv->timer_set_at = jiffies;
+ priv->timer_type = type;
mod_timer(&priv->timer, jiffies + ticks);
-} /* TLan_SetTimer */
+}
/*****************************************************************************
******************************************************************************
- ThunderLAN Driver Primary Functions
+ThunderLAN driver primary functions
- These functions are more or less common to all Linux network drivers.
+these functions are more or less common to all linux network drivers.
******************************************************************************
*****************************************************************************/
- /***************************************************************
- * tlan_remove_one
- *
- * Returns:
- * Nothing
- * Parms:
- * None
- *
- * Goes through the TLanDevices list and frees the device
- * structs and memory associated with each device (lists
- * and buffers). It also ureserves the IO port regions
- * associated with this device.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_remove_one
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * None
+ *
+ * Goes through the TLanDevices list and frees the device
+ * structs and memory associated with each device (lists
+ * and buffers). It also ureserves the IO port regions
+ * associated with this device.
+ *
+ **************************************************************/
-static void __devexit tlan_remove_one( struct pci_dev *pdev)
+static void __devexit tlan_remove_one(struct pci_dev *pdev)
{
- struct net_device *dev = pci_get_drvdata( pdev );
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct net_device *dev = pci_get_drvdata(pdev);
+ struct tlan_priv *priv = netdev_priv(dev);
- unregister_netdev( dev );
+ unregister_netdev(dev);
- if ( priv->dmaStorage ) {
- pci_free_consistent(priv->pciDev,
- priv->dmaSize, priv->dmaStorage,
- priv->dmaStorageDMA );
+ if (priv->dma_storage) {
+ pci_free_consistent(priv->pci_dev,
+ priv->dma_size, priv->dma_storage,
+ priv->dma_storage_dma);
}
#ifdef CONFIG_PCI
pci_release_regions(pdev);
#endif
- free_netdev( dev );
+ free_netdev(dev);
- pci_set_drvdata( pdev, NULL );
+ pci_set_drvdata(pdev, NULL);
}
static struct pci_driver tlan_driver = {
}
TLAN_DBG(TLAN_DEBUG_PROBE, "Starting EISA Probe....\n");
- TLan_EisaProbe();
+ tlan_eisa_probe();
printk(KERN_INFO "TLAN: %d device%s installed, PCI: %d EISA: %d\n",
- TLanDevicesInstalled, TLanDevicesInstalled == 1 ? "" : "s",
- tlan_have_pci, tlan_have_eisa);
+ tlan_devices_installed, tlan_devices_installed == 1 ? "" : "s",
+ tlan_have_pci, tlan_have_eisa);
- if (TLanDevicesInstalled == 0) {
+ if (tlan_devices_installed == 0) {
rc = -ENODEV;
goto err_out_pci_unreg;
}
}
-static int __devinit tlan_init_one( struct pci_dev *pdev,
- const struct pci_device_id *ent)
+static int __devinit tlan_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
{
- return TLan_probe1( pdev, -1, -1, 0, ent);
+ return tlan_probe1(pdev, -1, -1, 0, ent);
}
/*
- ***************************************************************
- * tlan_probe1
- *
- * Returns:
- * 0 on success, error code on error
- * Parms:
- * none
- *
- * The name is lower case to fit in with all the rest of
- * the netcard_probe names. This function looks for
- * another TLan based adapter, setting it up with the
- * allocated device struct if one is found.
- * tlan_probe has been ported to the new net API and
- * now allocates its own device structure. This function
- * is also used by modules.
- *
- **************************************************************/
-
-static int __devinit TLan_probe1(struct pci_dev *pdev,
+***************************************************************
+* tlan_probe1
+*
+* Returns:
+* 0 on success, error code on error
+* Parms:
+* none
+*
+* The name is lower case to fit in with all the rest of
+* the netcard_probe names. This function looks for
+* another TLan based adapter, setting it up with the
+* allocated device struct if one is found.
+* tlan_probe has been ported to the new net API and
+* now allocates its own device structure. This function
+* is also used by modules.
+*
+**************************************************************/
+
+static int __devinit tlan_probe1(struct pci_dev *pdev,
long ioaddr, int irq, int rev,
- const struct pci_device_id *ent )
+ const struct pci_device_id *ent)
{
struct net_device *dev;
- TLanPrivateInfo *priv;
+ struct tlan_priv *priv;
u16 device_id;
int reg, rc = -ENODEV;
if (rc)
return rc;
- rc = pci_request_regions(pdev, TLanSignature);
+ rc = pci_request_regions(pdev, tlan_signature);
if (rc) {
printk(KERN_ERR "TLAN: Could not reserve IO regions\n");
goto err_out;
}
#endif /* CONFIG_PCI */
- dev = alloc_etherdev(sizeof(TLanPrivateInfo));
+ dev = alloc_etherdev(sizeof(struct tlan_priv));
if (dev == NULL) {
printk(KERN_ERR "TLAN: Could not allocate memory for device.\n");
rc = -ENOMEM;
priv = netdev_priv(dev);
- priv->pciDev = pdev;
+ priv->pci_dev = pdev;
priv->dev = dev;
/* Is this a PCI device? */
if (pdev) {
- u32 pci_io_base = 0;
+ u32 pci_io_base = 0;
priv->adapter = &board_info[ent->driver_data];
rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
if (rc) {
- printk(KERN_ERR "TLAN: No suitable PCI mapping available.\n");
+ printk(KERN_ERR
+ "TLAN: No suitable PCI mapping available.\n");
goto err_out_free_dev;
}
- for ( reg= 0; reg <= 5; reg ++ ) {
+ for (reg = 0; reg <= 5; reg++) {
if (pci_resource_flags(pdev, reg) & IORESOURCE_IO) {
pci_io_base = pci_resource_start(pdev, reg);
- TLAN_DBG( TLAN_DEBUG_GNRL, "IO mapping is available at %x.\n",
- pci_io_base);
+ TLAN_DBG(TLAN_DEBUG_GNRL,
+ "IO mapping is available at %x.\n",
+ pci_io_base);
break;
}
}
dev->base_addr = pci_io_base;
dev->irq = pdev->irq;
- priv->adapterRev = pdev->revision;
+ priv->adapter_rev = pdev->revision;
pci_set_master(pdev);
pci_set_drvdata(pdev, dev);
device_id = inw(ioaddr + EISA_ID2);
priv->is_eisa = 1;
if (device_id == 0x20F1) {
- priv->adapter = &board_info[13]; /* NetFlex-3/E */
- priv->adapterRev = 23; /* TLAN 2.3 */
+ priv->adapter = &board_info[13]; /* NetFlex-3/E */
+ priv->adapter_rev = 23; /* TLAN 2.3 */
} else {
priv->adapter = &board_info[14];
- priv->adapterRev = 10; /* TLAN 1.0 */
+ priv->adapter_rev = 10; /* TLAN 1.0 */
}
dev->base_addr = ioaddr;
dev->irq = irq;
priv->speed = ((dev->mem_start & 0x18) == 0x18) ? 0
: (dev->mem_start & 0x18) >> 3;
- if (priv->speed == 0x1) {
+ if (priv->speed == 0x1)
priv->speed = TLAN_SPEED_10;
- } else if (priv->speed == 0x2) {
+ else if (priv->speed == 0x2)
priv->speed = TLAN_SPEED_100;
- }
+
debug = priv->debug = dev->mem_end;
} else {
priv->aui = aui[boards_found];
/* This will be used when we get an adapter error from
* within our irq handler */
- INIT_WORK(&priv->tlan_tqueue, TLan_tx_timeout_work);
+ INIT_WORK(&priv->tlan_tqueue, tlan_tx_timeout_work);
spin_lock_init(&priv->lock);
- rc = TLan_Init(dev);
+ rc = tlan_init(dev);
if (rc) {
printk(KERN_ERR "TLAN: Could not set up device.\n");
goto err_out_free_dev;
}
- TLanDevicesInstalled++;
+ tlan_devices_installed++;
boards_found++;
/* pdev is NULL if this is an EISA device */
if (pdev)
tlan_have_pci++;
else {
- priv->nextDevice = TLan_Eisa_Devices;
- TLan_Eisa_Devices = dev;
+ priv->next_device = tlan_eisa_devices;
+ tlan_eisa_devices = dev;
tlan_have_eisa++;
}
printk(KERN_INFO "TLAN: %s irq=%2d, io=%04x, %s, Rev. %d\n",
- dev->name,
- (int) dev->irq,
- (int) dev->base_addr,
- priv->adapter->deviceLabel,
- priv->adapterRev);
+ dev->name,
+ (int) dev->irq,
+ (int) dev->base_addr,
+ priv->adapter->device_label,
+ priv->adapter_rev);
return 0;
err_out_uninit:
- pci_free_consistent(priv->pciDev, priv->dmaSize, priv->dmaStorage,
- priv->dmaStorageDMA );
+ pci_free_consistent(priv->pci_dev, priv->dma_size, priv->dma_storage,
+ priv->dma_storage_dma);
err_out_free_dev:
free_netdev(dev);
err_out_regions:
}
-static void TLan_Eisa_Cleanup(void)
+static void tlan_eisa_cleanup(void)
{
struct net_device *dev;
- TLanPrivateInfo *priv;
+ struct tlan_priv *priv;
- while( tlan_have_eisa ) {
- dev = TLan_Eisa_Devices;
+ while (tlan_have_eisa) {
+ dev = tlan_eisa_devices;
priv = netdev_priv(dev);
- if (priv->dmaStorage) {
- pci_free_consistent(priv->pciDev, priv->dmaSize,
- priv->dmaStorage, priv->dmaStorageDMA );
+ if (priv->dma_storage) {
+ pci_free_consistent(priv->pci_dev, priv->dma_size,
+ priv->dma_storage,
+ priv->dma_storage_dma);
}
- release_region( dev->base_addr, 0x10);
- unregister_netdev( dev );
- TLan_Eisa_Devices = priv->nextDevice;
- free_netdev( dev );
+ release_region(dev->base_addr, 0x10);
+ unregister_netdev(dev);
+ tlan_eisa_devices = priv->next_device;
+ free_netdev(dev);
tlan_have_eisa--;
}
}
pci_unregister_driver(&tlan_driver);
if (tlan_have_eisa)
- TLan_Eisa_Cleanup();
+ tlan_eisa_cleanup();
}
- /**************************************************************
- * TLan_EisaProbe
- *
- * Returns: 0 on success, 1 otherwise
- *
- * Parms: None
- *
- *
- * This functions probes for EISA devices and calls
- * TLan_probe1 when one is found.
- *
- *************************************************************/
+/**************************************************************
+ * tlan_eisa_probe
+ *
+ * Returns: 0 on success, 1 otherwise
+ *
+ * Parms: None
+ *
+ *
+ * This functions probes for EISA devices and calls
+ * TLan_probe1 when one is found.
+ *
+ *************************************************************/
-static void __init TLan_EisaProbe (void)
+static void __init tlan_eisa_probe(void)
{
- long ioaddr;
- int rc = -ENODEV;
- int irq;
+ long ioaddr;
+ int rc = -ENODEV;
+ int irq;
u16 device_id;
if (!EISA_bus) {
/* Loop through all slots of the EISA bus */
for (ioaddr = 0x1000; ioaddr < 0x9000; ioaddr += 0x1000) {
- TLAN_DBG(TLAN_DEBUG_PROBE,"EISA_ID 0x%4x: 0x%4x\n",
- (int) ioaddr + 0xC80, inw(ioaddr + EISA_ID));
- TLAN_DBG(TLAN_DEBUG_PROBE,"EISA_ID 0x%4x: 0x%4x\n",
- (int) ioaddr + 0xC82, inw(ioaddr + EISA_ID2));
+ TLAN_DBG(TLAN_DEBUG_PROBE, "EISA_ID 0x%4x: 0x%4x\n",
+ (int) ioaddr + 0xc80, inw(ioaddr + EISA_ID));
+ TLAN_DBG(TLAN_DEBUG_PROBE, "EISA_ID 0x%4x: 0x%4x\n",
+ (int) ioaddr + 0xc82, inw(ioaddr + EISA_ID2));
- TLAN_DBG(TLAN_DEBUG_PROBE, "Probing for EISA adapter at IO: 0x%4x : ",
- (int) ioaddr);
- if (request_region(ioaddr, 0x10, TLanSignature) == NULL)
+ TLAN_DBG(TLAN_DEBUG_PROBE,
+ "Probing for EISA adapter at IO: 0x%4x : ",
+ (int) ioaddr);
+ if (request_region(ioaddr, 0x10, tlan_signature) == NULL)
goto out;
if (inw(ioaddr + EISA_ID) != 0x110E) {
device_id = inw(ioaddr + EISA_ID2);
if (device_id != 0x20F1 && device_id != 0x40F1) {
- release_region (ioaddr, 0x10);
+ release_region(ioaddr, 0x10);
goto out;
}
- if (inb(ioaddr + EISA_CR) != 0x1) { /* Check if adapter is enabled */
- release_region (ioaddr, 0x10);
+ /* check if adapter is enabled */
+ if (inb(ioaddr + EISA_CR) != 0x1) {
+ release_region(ioaddr, 0x10);
goto out2;
}
if (debug == 0x10)
- printk("Found one\n");
+ printk(KERN_INFO "Found one\n");
/* Get irq from board */
- switch (inb(ioaddr + 0xCC0)) {
- case(0x10):
- irq=5;
- break;
- case(0x20):
- irq=9;
- break;
- case(0x40):
- irq=10;
- break;
- case(0x80):
- irq=11;
- break;
- default:
- goto out;
+ switch (inb(ioaddr + 0xcc0)) {
+ case(0x10):
+ irq = 5;
+ break;
+ case(0x20):
+ irq = 9;
+ break;
+ case(0x40):
+ irq = 10;
+ break;
+ case(0x80):
+ irq = 11;
+ break;
+ default:
+ goto out;
}
/* Setup the newly found eisa adapter */
- rc = TLan_probe1( NULL, ioaddr, irq,
- 12, NULL);
+ rc = tlan_probe1(NULL, ioaddr, irq,
+ 12, NULL);
continue;
- out:
- if (debug == 0x10)
- printk("None found\n");
- continue;
+out:
+ if (debug == 0x10)
+ printk(KERN_INFO "None found\n");
+ continue;
- out2: if (debug == 0x10)
- printk("Card found but it is not enabled, skipping\n");
- continue;
+out2:
+ if (debug == 0x10)
+ printk(KERN_INFO "Card found but it is not enabled, skipping\n");
+ continue;
}
-} /* TLan_EisaProbe */
+}
#ifdef CONFIG_NET_POLL_CONTROLLER
-static void TLan_Poll(struct net_device *dev)
+static void tlan_poll(struct net_device *dev)
{
disable_irq(dev->irq);
- TLan_HandleInterrupt(dev->irq, dev);
+ tlan_handle_interrupt(dev->irq, dev);
enable_irq(dev->irq);
}
#endif
-static const struct net_device_ops TLan_netdev_ops = {
- .ndo_open = TLan_Open,
- .ndo_stop = TLan_Close,
- .ndo_start_xmit = TLan_StartTx,
- .ndo_tx_timeout = TLan_tx_timeout,
- .ndo_get_stats = TLan_GetStats,
- .ndo_set_multicast_list = TLan_SetMulticastList,
- .ndo_do_ioctl = TLan_ioctl,
+static const struct net_device_ops tlan_netdev_ops = {
+ .ndo_open = tlan_open,
+ .ndo_stop = tlan_close,
+ .ndo_start_xmit = tlan_start_tx,
+ .ndo_tx_timeout = tlan_tx_timeout,
+ .ndo_get_stats = tlan_get_stats,
+ .ndo_set_multicast_list = tlan_set_multicast_list,
+ .ndo_do_ioctl = tlan_ioctl,
.ndo_change_mtu = eth_change_mtu,
- .ndo_set_mac_address = eth_mac_addr,
+ .ndo_set_mac_address = eth_mac_addr,
.ndo_validate_addr = eth_validate_addr,
#ifdef CONFIG_NET_POLL_CONTROLLER
- .ndo_poll_controller = TLan_Poll,
+ .ndo_poll_controller = tlan_poll,
#endif
};
- /***************************************************************
- * TLan_Init
- *
- * Returns:
- * 0 on success, error code otherwise.
- * Parms:
- * dev The structure of the device to be
- * init'ed.
- *
- * This function completes the initialization of the
- * device structure and driver. It reserves the IO
- * addresses, allocates memory for the lists and bounce
- * buffers, retrieves the MAC address from the eeprom
- * and assignes the device's methods.
- *
- **************************************************************/
-
-static int TLan_Init( struct net_device *dev )
+/***************************************************************
+ * tlan_init
+ *
+ * Returns:
+ * 0 on success, error code otherwise.
+ * Parms:
+ * dev The structure of the device to be
+ * init'ed.
+ *
+ * This function completes the initialization of the
+ * device structure and driver. It reserves the IO
+ * addresses, allocates memory for the lists and bounce
+ * buffers, retrieves the MAC address from the eeprom
+ * and assignes the device's methods.
+ *
+ **************************************************************/
+
+static int tlan_init(struct net_device *dev)
{
int dma_size;
- int err;
+ int err;
int i;
- TLanPrivateInfo *priv;
+ struct tlan_priv *priv;
priv = netdev_priv(dev);
- dma_size = ( TLAN_NUM_RX_LISTS + TLAN_NUM_TX_LISTS )
- * ( sizeof(TLanList) );
- priv->dmaStorage = pci_alloc_consistent(priv->pciDev,
- dma_size, &priv->dmaStorageDMA);
- priv->dmaSize = dma_size;
-
- if ( priv->dmaStorage == NULL ) {
- printk(KERN_ERR "TLAN: Could not allocate lists and buffers for %s.\n",
- dev->name );
+ dma_size = (TLAN_NUM_RX_LISTS + TLAN_NUM_TX_LISTS)
+ * (sizeof(struct tlan_list));
+ priv->dma_storage = pci_alloc_consistent(priv->pci_dev,
+ dma_size,
+ &priv->dma_storage_dma);
+ priv->dma_size = dma_size;
+
+ if (priv->dma_storage == NULL) {
+ printk(KERN_ERR
+ "TLAN: Could not allocate lists and buffers for %s.\n",
+ dev->name);
return -ENOMEM;
}
- memset( priv->dmaStorage, 0, dma_size );
- priv->rxList = (TLanList *) ALIGN((unsigned long)priv->dmaStorage, 8);
- priv->rxListDMA = ALIGN(priv->dmaStorageDMA, 8);
- priv->txList = priv->rxList + TLAN_NUM_RX_LISTS;
- priv->txListDMA = priv->rxListDMA + sizeof(TLanList) * TLAN_NUM_RX_LISTS;
+ memset(priv->dma_storage, 0, dma_size);
+ priv->rx_list = (struct tlan_list *)
+ ALIGN((unsigned long)priv->dma_storage, 8);
+ priv->rx_list_dma = ALIGN(priv->dma_storage_dma, 8);
+ priv->tx_list = priv->rx_list + TLAN_NUM_RX_LISTS;
+ priv->tx_list_dma =
+ priv->rx_list_dma + sizeof(struct tlan_list)*TLAN_NUM_RX_LISTS;
err = 0;
- for ( i = 0; i < 6 ; i++ )
- err |= TLan_EeReadByte( dev,
- (u8) priv->adapter->addrOfs + i,
- (u8 *) &dev->dev_addr[i] );
- if ( err ) {
+ for (i = 0; i < 6 ; i++)
+ err |= tlan_ee_read_byte(dev,
+ (u8) priv->adapter->addr_ofs + i,
+ (u8 *) &dev->dev_addr[i]);
+ if (err) {
printk(KERN_ERR "TLAN: %s: Error reading MAC from eeprom: %d\n",
- dev->name,
- err );
+ dev->name,
+ err);
}
dev->addr_len = 6;
netif_carrier_off(dev);
/* Device methods */
- dev->netdev_ops = &TLan_netdev_ops;
+ dev->netdev_ops = &tlan_netdev_ops;
dev->watchdog_timeo = TX_TIMEOUT;
return 0;
-} /* TLan_Init */
+}
- /***************************************************************
- * TLan_Open
- *
- * Returns:
- * 0 on success, error code otherwise.
- * Parms:
- * dev Structure of device to be opened.
- *
- * This routine puts the driver and TLAN adapter in a
- * state where it is ready to send and receive packets.
- * It allocates the IRQ, resets and brings the adapter
- * out of reset, and allows interrupts. It also delays
- * the startup for autonegotiation or sends a Rx GO
- * command to the adapter, as appropriate.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_open
+ *
+ * Returns:
+ * 0 on success, error code otherwise.
+ * Parms:
+ * dev Structure of device to be opened.
+ *
+ * This routine puts the driver and TLAN adapter in a
+ * state where it is ready to send and receive packets.
+ * It allocates the IRQ, resets and brings the adapter
+ * out of reset, and allows interrupts. It also delays
+ * the startup for autonegotiation or sends a Rx GO
+ * command to the adapter, as appropriate.
+ *
+ **************************************************************/
-static int TLan_Open( struct net_device *dev )
+static int tlan_open(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
int err;
- priv->tlanRev = TLan_DioRead8( dev->base_addr, TLAN_DEF_REVISION );
- err = request_irq( dev->irq, TLan_HandleInterrupt, IRQF_SHARED,
- dev->name, dev );
+ priv->tlan_rev = tlan_dio_read8(dev->base_addr, TLAN_DEF_REVISION);
+ err = request_irq(dev->irq, tlan_handle_interrupt, IRQF_SHARED,
+ dev->name, dev);
- if ( err ) {
+ if (err) {
pr_err("TLAN: Cannot open %s because IRQ %d is already in use.\n",
- dev->name, dev->irq );
+ dev->name, dev->irq);
return err;
}
netif_start_queue(dev);
/* NOTE: It might not be necessary to read the stats before a
- reset if you don't care what the values are.
+ reset if you don't care what the values are.
*/
- TLan_ResetLists( dev );
- TLan_ReadAndClearStats( dev, TLAN_IGNORE );
- TLan_ResetAdapter( dev );
+ tlan_reset_lists(dev);
+ tlan_read_and_clear_stats(dev, TLAN_IGNORE);
+ tlan_reset_adapter(dev);
- TLAN_DBG( TLAN_DEBUG_GNRL, "%s: Opened. TLAN Chip Rev: %x\n",
- dev->name, priv->tlanRev );
+ TLAN_DBG(TLAN_DEBUG_GNRL, "%s: Opened. TLAN Chip Rev: %x\n",
+ dev->name, priv->tlan_rev);
return 0;
-} /* TLan_Open */
+}
- /**************************************************************
- * TLan_ioctl
- *
- * Returns:
- * 0 on success, error code otherwise
- * Params:
- * dev structure of device to receive ioctl.
- *
- * rq ifreq structure to hold userspace data.
- *
- * cmd ioctl command.
- *
- *
- *************************************************************/
+/**************************************************************
+ * tlan_ioctl
+ *
+ * Returns:
+ * 0 on success, error code otherwise
+ * Params:
+ * dev structure of device to receive ioctl.
+ *
+ * rq ifreq structure to hold userspace data.
+ *
+ * cmd ioctl command.
+ *
+ *
+ *************************************************************/
-static int TLan_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+static int tlan_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
struct mii_ioctl_data *data = if_mii(rq);
- u32 phy = priv->phy[priv->phyNum];
+ u32 phy = priv->phy[priv->phy_num];
- if (!priv->phyOnline)
+ if (!priv->phy_online)
return -EAGAIN;
- switch(cmd) {
- case SIOCGMIIPHY: /* Get address of MII PHY in use. */
- data->phy_id = phy;
+ switch (cmd) {
+ case SIOCGMIIPHY: /* get address of MII PHY in use. */
+ data->phy_id = phy;
- case SIOCGMIIREG: /* Read MII PHY register. */
- TLan_MiiReadReg(dev, data->phy_id & 0x1f,
- data->reg_num & 0x1f, &data->val_out);
- return 0;
+ case SIOCGMIIREG: /* read MII PHY register. */
+ tlan_mii_read_reg(dev, data->phy_id & 0x1f,
+ data->reg_num & 0x1f, &data->val_out);
+ return 0;
- case SIOCSMIIREG: /* Write MII PHY register. */
- TLan_MiiWriteReg(dev, data->phy_id & 0x1f,
- data->reg_num & 0x1f, data->val_in);
- return 0;
- default:
- return -EOPNOTSUPP;
+ case SIOCSMIIREG: /* write MII PHY register. */
+ tlan_mii_write_reg(dev, data->phy_id & 0x1f,
+ data->reg_num & 0x1f, data->val_in);
+ return 0;
+ default:
+ return -EOPNOTSUPP;
}
-} /* tlan_ioctl */
+}
- /***************************************************************
- * TLan_tx_timeout
- *
- * Returns: nothing
- *
- * Params:
- * dev structure of device which timed out
- * during transmit.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_tx_timeout
+ *
+ * Returns: nothing
+ *
+ * Params:
+ * dev structure of device which timed out
+ * during transmit.
+ *
+ **************************************************************/
-static void TLan_tx_timeout(struct net_device *dev)
+static void tlan_tx_timeout(struct net_device *dev)
{
- TLAN_DBG( TLAN_DEBUG_GNRL, "%s: Transmit timed out.\n", dev->name);
+ TLAN_DBG(TLAN_DEBUG_GNRL, "%s: Transmit timed out.\n", dev->name);
/* Ok so we timed out, lets see what we can do about it...*/
- TLan_FreeLists( dev );
- TLan_ResetLists( dev );
- TLan_ReadAndClearStats( dev, TLAN_IGNORE );
- TLan_ResetAdapter( dev );
+ tlan_free_lists(dev);
+ tlan_reset_lists(dev);
+ tlan_read_and_clear_stats(dev, TLAN_IGNORE);
+ tlan_reset_adapter(dev);
dev->trans_start = jiffies; /* prevent tx timeout */
- netif_wake_queue( dev );
+ netif_wake_queue(dev);
}
- /***************************************************************
- * TLan_tx_timeout_work
- *
- * Returns: nothing
- *
- * Params:
- * work work item of device which timed out
- *
- **************************************************************/
+/***************************************************************
+ * tlan_tx_timeout_work
+ *
+ * Returns: nothing
+ *
+ * Params:
+ * work work item of device which timed out
+ *
+ **************************************************************/
-static void TLan_tx_timeout_work(struct work_struct *work)
+static void tlan_tx_timeout_work(struct work_struct *work)
{
- TLanPrivateInfo *priv =
- container_of(work, TLanPrivateInfo, tlan_tqueue);
+ struct tlan_priv *priv =
+ container_of(work, struct tlan_priv, tlan_tqueue);
- TLan_tx_timeout(priv->dev);
+ tlan_tx_timeout(priv->dev);
}
- /***************************************************************
- * TLan_StartTx
- *
- * Returns:
- * 0 on success, non-zero on failure.
- * Parms:
- * skb A pointer to the sk_buff containing the
- * frame to be sent.
- * dev The device to send the data on.
- *
- * This function adds a frame to the Tx list to be sent
- * ASAP. First it verifies that the adapter is ready and
- * there is room in the queue. Then it sets up the next
- * available list, copies the frame to the corresponding
- * buffer. If the adapter Tx channel is idle, it gives
- * the adapter a Tx Go command on the list, otherwise it
- * sets the forward address of the previous list to point
- * to this one. Then it frees the sk_buff.
- *
- **************************************************************/
-
-static netdev_tx_t TLan_StartTx( struct sk_buff *skb, struct net_device *dev )
+/***************************************************************
+ * tlan_start_tx
+ *
+ * Returns:
+ * 0 on success, non-zero on failure.
+ * Parms:
+ * skb A pointer to the sk_buff containing the
+ * frame to be sent.
+ * dev The device to send the data on.
+ *
+ * This function adds a frame to the Tx list to be sent
+ * ASAP. First it verifies that the adapter is ready and
+ * there is room in the queue. Then it sets up the next
+ * available list, copies the frame to the corresponding
+ * buffer. If the adapter Tx channel is idle, it gives
+ * the adapter a Tx Go command on the list, otherwise it
+ * sets the forward address of the previous list to point
+ * to this one. Then it frees the sk_buff.
+ *
+ **************************************************************/
+
+static netdev_tx_t tlan_start_tx(struct sk_buff *skb, struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
dma_addr_t tail_list_phys;
- TLanList *tail_list;
+ struct tlan_list *tail_list;
unsigned long flags;
unsigned int txlen;
- if ( ! priv->phyOnline ) {
- TLAN_DBG( TLAN_DEBUG_TX, "TRANSMIT: %s PHY is not ready\n",
- dev->name );
+ if (!priv->phy_online) {
+ TLAN_DBG(TLAN_DEBUG_TX, "TRANSMIT: %s PHY is not ready\n",
+ dev->name);
dev_kfree_skb_any(skb);
return NETDEV_TX_OK;
}
return NETDEV_TX_OK;
txlen = max(skb->len, (unsigned int)TLAN_MIN_FRAME_SIZE);
- tail_list = priv->txList + priv->txTail;
- tail_list_phys = priv->txListDMA + sizeof(TLanList) * priv->txTail;
+ tail_list = priv->tx_list + priv->tx_tail;
+ tail_list_phys =
+ priv->tx_list_dma + sizeof(struct tlan_list)*priv->tx_tail;
- if ( tail_list->cStat != TLAN_CSTAT_UNUSED ) {
- TLAN_DBG( TLAN_DEBUG_TX,
- "TRANSMIT: %s is busy (Head=%d Tail=%d)\n",
- dev->name, priv->txHead, priv->txTail );
+ if (tail_list->c_stat != TLAN_CSTAT_UNUSED) {
+ TLAN_DBG(TLAN_DEBUG_TX,
+ "TRANSMIT: %s is busy (Head=%d Tail=%d)\n",
+ dev->name, priv->tx_head, priv->tx_tail);
netif_stop_queue(dev);
- priv->txBusyCount++;
+ priv->tx_busy_count++;
return NETDEV_TX_BUSY;
}
tail_list->forward = 0;
- tail_list->buffer[0].address = pci_map_single(priv->pciDev,
+ tail_list->buffer[0].address = pci_map_single(priv->pci_dev,
skb->data, txlen,
PCI_DMA_TODEVICE);
- TLan_StoreSKB(tail_list, skb);
+ tlan_store_skb(tail_list, skb);
- tail_list->frameSize = (u16) txlen;
+ tail_list->frame_size = (u16) txlen;
tail_list->buffer[0].count = TLAN_LAST_BUFFER | (u32) txlen;
tail_list->buffer[1].count = 0;
tail_list->buffer[1].address = 0;
spin_lock_irqsave(&priv->lock, flags);
- tail_list->cStat = TLAN_CSTAT_READY;
- if ( ! priv->txInProgress ) {
- priv->txInProgress = 1;
- TLAN_DBG( TLAN_DEBUG_TX,
- "TRANSMIT: Starting TX on buffer %d\n", priv->txTail );
- outl( tail_list_phys, dev->base_addr + TLAN_CH_PARM );
- outl( TLAN_HC_GO, dev->base_addr + TLAN_HOST_CMD );
+ tail_list->c_stat = TLAN_CSTAT_READY;
+ if (!priv->tx_in_progress) {
+ priv->tx_in_progress = 1;
+ TLAN_DBG(TLAN_DEBUG_TX,
+ "TRANSMIT: Starting TX on buffer %d\n",
+ priv->tx_tail);
+ outl(tail_list_phys, dev->base_addr + TLAN_CH_PARM);
+ outl(TLAN_HC_GO, dev->base_addr + TLAN_HOST_CMD);
} else {
- TLAN_DBG( TLAN_DEBUG_TX, "TRANSMIT: Adding buffer %d to TX channel\n",
- priv->txTail );
- if ( priv->txTail == 0 ) {
- ( priv->txList + ( TLAN_NUM_TX_LISTS - 1 ) )->forward
+ TLAN_DBG(TLAN_DEBUG_TX,
+ "TRANSMIT: Adding buffer %d to TX channel\n",
+ priv->tx_tail);
+ if (priv->tx_tail == 0) {
+ (priv->tx_list + (TLAN_NUM_TX_LISTS - 1))->forward
= tail_list_phys;
} else {
- ( priv->txList + ( priv->txTail - 1 ) )->forward
+ (priv->tx_list + (priv->tx_tail - 1))->forward
= tail_list_phys;
}
}
spin_unlock_irqrestore(&priv->lock, flags);
- CIRC_INC( priv->txTail, TLAN_NUM_TX_LISTS );
+ CIRC_INC(priv->tx_tail, TLAN_NUM_TX_LISTS);
return NETDEV_TX_OK;
-} /* TLan_StartTx */
+}
- /***************************************************************
- * TLan_HandleInterrupt
- *
- * Returns:
- * Nothing
- * Parms:
- * irq The line on which the interrupt
- * occurred.
- * dev_id A pointer to the device assigned to
- * this irq line.
- *
- * This function handles an interrupt generated by its
- * assigned TLAN adapter. The function deactivates
- * interrupts on its adapter, records the type of
- * interrupt, executes the appropriate subhandler, and
- * acknowdges the interrupt to the adapter (thus
- * re-enabling adapter interrupts.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_handle_interrupt
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * irq The line on which the interrupt
+ * occurred.
+ * dev_id A pointer to the device assigned to
+ * this irq line.
+ *
+ * This function handles an interrupt generated by its
+ * assigned TLAN adapter. The function deactivates
+ * interrupts on its adapter, records the type of
+ * interrupt, executes the appropriate subhandler, and
+ * acknowdges the interrupt to the adapter (thus
+ * re-enabling adapter interrupts.
+ *
+ **************************************************************/
-static irqreturn_t TLan_HandleInterrupt(int irq, void *dev_id)
+static irqreturn_t tlan_handle_interrupt(int irq, void *dev_id)
{
struct net_device *dev = dev_id;
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u16 host_int;
u16 type;
spin_lock(&priv->lock);
- host_int = inw( dev->base_addr + TLAN_HOST_INT );
- type = ( host_int & TLAN_HI_IT_MASK ) >> 2;
- if ( type ) {
+ host_int = inw(dev->base_addr + TLAN_HOST_INT);
+ type = (host_int & TLAN_HI_IT_MASK) >> 2;
+ if (type) {
u32 ack;
u32 host_cmd;
- outw( host_int, dev->base_addr + TLAN_HOST_INT );
- ack = TLanIntVector[type]( dev, host_int );
+ outw(host_int, dev->base_addr + TLAN_HOST_INT);
+ ack = tlan_int_vector[type](dev, host_int);
- if ( ack ) {
- host_cmd = TLAN_HC_ACK | ack | ( type << 18 );
- outl( host_cmd, dev->base_addr + TLAN_HOST_CMD );
+ if (ack) {
+ host_cmd = TLAN_HC_ACK | ack | (type << 18);
+ outl(host_cmd, dev->base_addr + TLAN_HOST_CMD);
}
}
spin_unlock(&priv->lock);
return IRQ_RETVAL(type);
-} /* TLan_HandleInterrupts */
+}
- /***************************************************************
- * TLan_Close
- *
- * Returns:
- * An error code.
- * Parms:
- * dev The device structure of the device to
- * close.
- *
- * This function shuts down the adapter. It records any
- * stats, puts the adapter into reset state, deactivates
- * its time as needed, and frees the irq it is using.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_close
+ *
+ * Returns:
+ * An error code.
+ * Parms:
+ * dev The device structure of the device to
+ * close.
+ *
+ * This function shuts down the adapter. It records any
+ * stats, puts the adapter into reset state, deactivates
+ * its time as needed, and frees the irq it is using.
+ *
+ **************************************************************/
-static int TLan_Close(struct net_device *dev)
+static int tlan_close(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
netif_stop_queue(dev);
priv->neg_be_verbose = 0;
- TLan_ReadAndClearStats( dev, TLAN_RECORD );
- outl( TLAN_HC_AD_RST, dev->base_addr + TLAN_HOST_CMD );
- if ( priv->timer.function != NULL ) {
- del_timer_sync( &priv->timer );
+ tlan_read_and_clear_stats(dev, TLAN_RECORD);
+ outl(TLAN_HC_AD_RST, dev->base_addr + TLAN_HOST_CMD);
+ if (priv->timer.function != NULL) {
+ del_timer_sync(&priv->timer);
priv->timer.function = NULL;
}
- free_irq( dev->irq, dev );
- TLan_FreeLists( dev );
- TLAN_DBG( TLAN_DEBUG_GNRL, "Device %s closed.\n", dev->name );
+ free_irq(dev->irq, dev);
+ tlan_free_lists(dev);
+ TLAN_DBG(TLAN_DEBUG_GNRL, "Device %s closed.\n", dev->name);
return 0;
-} /* TLan_Close */
+}
- /***************************************************************
- * TLan_GetStats
- *
- * Returns:
- * A pointer to the device's statistics structure.
- * Parms:
- * dev The device structure to return the
- * stats for.
- *
- * This function updates the devices statistics by reading
- * the TLAN chip's onboard registers. Then it returns the
- * address of the statistics structure.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_get_stats
+ *
+ * Returns:
+ * A pointer to the device's statistics structure.
+ * Parms:
+ * dev The device structure to return the
+ * stats for.
+ *
+ * This function updates the devices statistics by reading
+ * the TLAN chip's onboard registers. Then it returns the
+ * address of the statistics structure.
+ *
+ **************************************************************/
-static struct net_device_stats *TLan_GetStats( struct net_device *dev )
+static struct net_device_stats *tlan_get_stats(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
int i;
/* Should only read stats if open ? */
- TLan_ReadAndClearStats( dev, TLAN_RECORD );
+ tlan_read_and_clear_stats(dev, TLAN_RECORD);
- TLAN_DBG( TLAN_DEBUG_RX, "RECEIVE: %s EOC count = %d\n", dev->name,
- priv->rxEocCount );
- TLAN_DBG( TLAN_DEBUG_TX, "TRANSMIT: %s Busy count = %d\n", dev->name,
- priv->txBusyCount );
- if ( debug & TLAN_DEBUG_GNRL ) {
- TLan_PrintDio( dev->base_addr );
- TLan_PhyPrint( dev );
+ TLAN_DBG(TLAN_DEBUG_RX, "RECEIVE: %s EOC count = %d\n", dev->name,
+ priv->rx_eoc_count);
+ TLAN_DBG(TLAN_DEBUG_TX, "TRANSMIT: %s Busy count = %d\n", dev->name,
+ priv->tx_busy_count);
+ if (debug & TLAN_DEBUG_GNRL) {
+ tlan_print_dio(dev->base_addr);
+ tlan_phy_print(dev);
}
- if ( debug & TLAN_DEBUG_LIST ) {
- for ( i = 0; i < TLAN_NUM_RX_LISTS; i++ )
- TLan_PrintList( priv->rxList + i, "RX", i );
- for ( i = 0; i < TLAN_NUM_TX_LISTS; i++ )
- TLan_PrintList( priv->txList + i, "TX", i );
+ if (debug & TLAN_DEBUG_LIST) {
+ for (i = 0; i < TLAN_NUM_RX_LISTS; i++)
+ tlan_print_list(priv->rx_list + i, "RX", i);
+ for (i = 0; i < TLAN_NUM_TX_LISTS; i++)
+ tlan_print_list(priv->tx_list + i, "TX", i);
}
return &dev->stats;
-} /* TLan_GetStats */
+}
- /***************************************************************
- * TLan_SetMulticastList
- *
- * Returns:
- * Nothing
- * Parms:
- * dev The device structure to set the
- * multicast list for.
- *
- * This function sets the TLAN adaptor to various receive
- * modes. If the IFF_PROMISC flag is set, promiscuous
- * mode is acitviated. Otherwise, promiscuous mode is
- * turned off. If the IFF_ALLMULTI flag is set, then
- * the hash table is set to receive all group addresses.
- * Otherwise, the first three multicast addresses are
- * stored in AREG_1-3, and the rest are selected via the
- * hash table, as necessary.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_set_multicast_list
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * dev The device structure to set the
+ * multicast list for.
+ *
+ * This function sets the TLAN adaptor to various receive
+ * modes. If the IFF_PROMISC flag is set, promiscuous
+ * mode is acitviated. Otherwise, promiscuous mode is
+ * turned off. If the IFF_ALLMULTI flag is set, then
+ * the hash table is set to receive all group addresses.
+ * Otherwise, the first three multicast addresses are
+ * stored in AREG_1-3, and the rest are selected via the
+ * hash table, as necessary.
+ *
+ **************************************************************/
-static void TLan_SetMulticastList( struct net_device *dev )
+static void tlan_set_multicast_list(struct net_device *dev)
{
struct netdev_hw_addr *ha;
u32 hash1 = 0;
u32 offset;
u8 tmp;
- if ( dev->flags & IFF_PROMISC ) {
- tmp = TLan_DioRead8( dev->base_addr, TLAN_NET_CMD );
- TLan_DioWrite8( dev->base_addr,
- TLAN_NET_CMD, tmp | TLAN_NET_CMD_CAF );
+ if (dev->flags & IFF_PROMISC) {
+ tmp = tlan_dio_read8(dev->base_addr, TLAN_NET_CMD);
+ tlan_dio_write8(dev->base_addr,
+ TLAN_NET_CMD, tmp | TLAN_NET_CMD_CAF);
} else {
- tmp = TLan_DioRead8( dev->base_addr, TLAN_NET_CMD );
- TLan_DioWrite8( dev->base_addr,
- TLAN_NET_CMD, tmp & ~TLAN_NET_CMD_CAF );
- if ( dev->flags & IFF_ALLMULTI ) {
- for ( i = 0; i < 3; i++ )
- TLan_SetMac( dev, i + 1, NULL );
- TLan_DioWrite32( dev->base_addr, TLAN_HASH_1, 0xFFFFFFFF );
- TLan_DioWrite32( dev->base_addr, TLAN_HASH_2, 0xFFFFFFFF );
+ tmp = tlan_dio_read8(dev->base_addr, TLAN_NET_CMD);
+ tlan_dio_write8(dev->base_addr,
+ TLAN_NET_CMD, tmp & ~TLAN_NET_CMD_CAF);
+ if (dev->flags & IFF_ALLMULTI) {
+ for (i = 0; i < 3; i++)
+ tlan_set_mac(dev, i + 1, NULL);
+ tlan_dio_write32(dev->base_addr, TLAN_HASH_1,
+ 0xffffffff);
+ tlan_dio_write32(dev->base_addr, TLAN_HASH_2,
+ 0xffffffff);
} else {
i = 0;
netdev_for_each_mc_addr(ha, dev) {
- if ( i < 3 ) {
- TLan_SetMac( dev, i + 1,
+ if (i < 3) {
+ tlan_set_mac(dev, i + 1,
(char *) &ha->addr);
} else {
- offset = TLan_HashFunc((u8 *)&ha->addr);
- if ( offset < 32 )
- hash1 |= ( 1 << offset );
+ offset =
+ tlan_hash_func((u8 *)&ha->addr);
+ if (offset < 32)
+ hash1 |= (1 << offset);
else
- hash2 |= ( 1 << ( offset - 32 ) );
+ hash2 |= (1 << (offset - 32));
}
i++;
}
- for ( ; i < 3; i++ )
- TLan_SetMac( dev, i + 1, NULL );
- TLan_DioWrite32( dev->base_addr, TLAN_HASH_1, hash1 );
- TLan_DioWrite32( dev->base_addr, TLAN_HASH_2, hash2 );
+ for ( ; i < 3; i++)
+ tlan_set_mac(dev, i + 1, NULL);
+ tlan_dio_write32(dev->base_addr, TLAN_HASH_1, hash1);
+ tlan_dio_write32(dev->base_addr, TLAN_HASH_2, hash2);
}
}
-} /* TLan_SetMulticastList */
+}
/*****************************************************************************
******************************************************************************
- ThunderLAN Driver Interrupt Vectors and Table
+ThunderLAN driver interrupt vectors and table
- Please see Chap. 4, "Interrupt Handling" of the "ThunderLAN
- Programmer's Guide" for more informations on handling interrupts
- generated by TLAN based adapters.
+please see chap. 4, "Interrupt Handling" of the "ThunderLAN
+Programmer's Guide" for more informations on handling interrupts
+generated by TLAN based adapters.
******************************************************************************
*****************************************************************************/
- /***************************************************************
- * TLan_HandleTxEOF
- *
- * Returns:
- * 1
- * Parms:
- * dev Device assigned the IRQ that was
- * raised.
- * host_int The contents of the HOST_INT
- * port.
- *
- * This function handles Tx EOF interrupts which are raised
- * by the adapter when it has completed sending the
- * contents of a buffer. If detemines which list/buffer
- * was completed and resets it. If the buffer was the last
- * in the channel (EOC), then the function checks to see if
- * another buffer is ready to send, and if so, sends a Tx
- * Go command. Finally, the driver activates/continues the
- * activity LED.
- *
- **************************************************************/
-
-static u32 TLan_HandleTxEOF( struct net_device *dev, u16 host_int )
+/***************************************************************
+ * tlan_handle_tx_eof
+ *
+ * Returns:
+ * 1
+ * Parms:
+ * dev Device assigned the IRQ that was
+ * raised.
+ * host_int The contents of the HOST_INT
+ * port.
+ *
+ * This function handles Tx EOF interrupts which are raised
+ * by the adapter when it has completed sending the
+ * contents of a buffer. If detemines which list/buffer
+ * was completed and resets it. If the buffer was the last
+ * in the channel (EOC), then the function checks to see if
+ * another buffer is ready to send, and if so, sends a Tx
+ * Go command. Finally, the driver activates/continues the
+ * activity LED.
+ *
+ **************************************************************/
+
+static u32 tlan_handle_tx_eof(struct net_device *dev, u16 host_int)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
int eoc = 0;
- TLanList *head_list;
+ struct tlan_list *head_list;
dma_addr_t head_list_phys;
u32 ack = 0;
- u16 tmpCStat;
+ u16 tmp_c_stat;
- TLAN_DBG( TLAN_DEBUG_TX, "TRANSMIT: Handling TX EOF (Head=%d Tail=%d)\n",
- priv->txHead, priv->txTail );
- head_list = priv->txList + priv->txHead;
+ TLAN_DBG(TLAN_DEBUG_TX,
+ "TRANSMIT: Handling TX EOF (Head=%d Tail=%d)\n",
+ priv->tx_head, priv->tx_tail);
+ head_list = priv->tx_list + priv->tx_head;
- while (((tmpCStat = head_list->cStat ) & TLAN_CSTAT_FRM_CMP) && (ack < 255)) {
- struct sk_buff *skb = TLan_GetSKB(head_list);
+ while (((tmp_c_stat = head_list->c_stat) & TLAN_CSTAT_FRM_CMP)
+ && (ack < 255)) {
+ struct sk_buff *skb = tlan_get_skb(head_list);
ack++;
- pci_unmap_single(priv->pciDev, head_list->buffer[0].address,
+ pci_unmap_single(priv->pci_dev, head_list->buffer[0].address,
max(skb->len,
(unsigned int)TLAN_MIN_FRAME_SIZE),
PCI_DMA_TODEVICE);
head_list->buffer[8].address = 0;
head_list->buffer[9].address = 0;
- if ( tmpCStat & TLAN_CSTAT_EOC )
+ if (tmp_c_stat & TLAN_CSTAT_EOC)
eoc = 1;
- dev->stats.tx_bytes += head_list->frameSize;
+ dev->stats.tx_bytes += head_list->frame_size;
- head_list->cStat = TLAN_CSTAT_UNUSED;
+ head_list->c_stat = TLAN_CSTAT_UNUSED;
netif_start_queue(dev);
- CIRC_INC( priv->txHead, TLAN_NUM_TX_LISTS );
- head_list = priv->txList + priv->txHead;
+ CIRC_INC(priv->tx_head, TLAN_NUM_TX_LISTS);
+ head_list = priv->tx_list + priv->tx_head;
}
if (!ack)
- printk(KERN_INFO "TLAN: Received interrupt for uncompleted TX frame.\n");
-
- if ( eoc ) {
- TLAN_DBG( TLAN_DEBUG_TX,
- "TRANSMIT: Handling TX EOC (Head=%d Tail=%d)\n",
- priv->txHead, priv->txTail );
- head_list = priv->txList + priv->txHead;
- head_list_phys = priv->txListDMA + sizeof(TLanList) * priv->txHead;
- if ( ( head_list->cStat & TLAN_CSTAT_READY ) == TLAN_CSTAT_READY ) {
- outl(head_list_phys, dev->base_addr + TLAN_CH_PARM );
+ printk(KERN_INFO
+ "TLAN: Received interrupt for uncompleted TX frame.\n");
+
+ if (eoc) {
+ TLAN_DBG(TLAN_DEBUG_TX,
+ "TRANSMIT: handling TX EOC (Head=%d Tail=%d)\n",
+ priv->tx_head, priv->tx_tail);
+ head_list = priv->tx_list + priv->tx_head;
+ head_list_phys = priv->tx_list_dma
+ + sizeof(struct tlan_list)*priv->tx_head;
+ if (head_list->c_stat & TLAN_CSTAT_READY) {
+ outl(head_list_phys, dev->base_addr + TLAN_CH_PARM);
ack |= TLAN_HC_GO;
} else {
- priv->txInProgress = 0;
+ priv->tx_in_progress = 0;
}
}
- if ( priv->adapter->flags & TLAN_ADAPTER_ACTIVITY_LED ) {
- TLan_DioWrite8( dev->base_addr,
- TLAN_LED_REG, TLAN_LED_LINK | TLAN_LED_ACT );
- if ( priv->timer.function == NULL ) {
- priv->timer.function = TLan_Timer;
- priv->timer.data = (unsigned long) dev;
- priv->timer.expires = jiffies + TLAN_TIMER_ACT_DELAY;
- priv->timerSetAt = jiffies;
- priv->timerType = TLAN_TIMER_ACTIVITY;
- add_timer(&priv->timer);
- } else if ( priv->timerType == TLAN_TIMER_ACTIVITY ) {
- priv->timerSetAt = jiffies;
+ if (priv->adapter->flags & TLAN_ADAPTER_ACTIVITY_LED) {
+ tlan_dio_write8(dev->base_addr,
+ TLAN_LED_REG, TLAN_LED_LINK | TLAN_LED_ACT);
+ if (priv->timer.function == NULL) {
+ priv->timer.function = tlan_timer;
+ priv->timer.data = (unsigned long) dev;
+ priv->timer.expires = jiffies + TLAN_TIMER_ACT_DELAY;
+ priv->timer_set_at = jiffies;
+ priv->timer_type = TLAN_TIMER_ACTIVITY;
+ add_timer(&priv->timer);
+ } else if (priv->timer_type == TLAN_TIMER_ACTIVITY) {
+ priv->timer_set_at = jiffies;
}
}
return ack;
-} /* TLan_HandleTxEOF */
+}
- /***************************************************************
- * TLan_HandleStatOverflow
- *
- * Returns:
- * 1
- * Parms:
- * dev Device assigned the IRQ that was
- * raised.
- * host_int The contents of the HOST_INT
- * port.
- *
- * This function handles the Statistics Overflow interrupt
- * which means that one or more of the TLAN statistics
- * registers has reached 1/2 capacity and needs to be read.
- *
- **************************************************************/
+/***************************************************************
+ * TLan_HandleStatOverflow
+ *
+ * Returns:
+ * 1
+ * Parms:
+ * dev Device assigned the IRQ that was
+ * raised.
+ * host_int The contents of the HOST_INT
+ * port.
+ *
+ * This function handles the Statistics Overflow interrupt
+ * which means that one or more of the TLAN statistics
+ * registers has reached 1/2 capacity and needs to be read.
+ *
+ **************************************************************/
-static u32 TLan_HandleStatOverflow( struct net_device *dev, u16 host_int )
+static u32 tlan_handle_stat_overflow(struct net_device *dev, u16 host_int)
{
- TLan_ReadAndClearStats( dev, TLAN_RECORD );
+ tlan_read_and_clear_stats(dev, TLAN_RECORD);
return 1;
-} /* TLan_HandleStatOverflow */
-
-
-
-
- /***************************************************************
- * TLan_HandleRxEOF
- *
- * Returns:
- * 1
- * Parms:
- * dev Device assigned the IRQ that was
- * raised.
- * host_int The contents of the HOST_INT
- * port.
- *
- * This function handles the Rx EOF interrupt which
- * indicates a frame has been received by the adapter from
- * the net and the frame has been transferred to memory.
- * The function determines the bounce buffer the frame has
- * been loaded into, creates a new sk_buff big enough to
- * hold the frame, and sends it to protocol stack. It
- * then resets the used buffer and appends it to the end
- * of the list. If the frame was the last in the Rx
- * channel (EOC), the function restarts the receive channel
- * by sending an Rx Go command to the adapter. Then it
- * activates/continues the activity LED.
- *
- **************************************************************/
-
-static u32 TLan_HandleRxEOF( struct net_device *dev, u16 host_int )
+}
+
+
+
+
+/***************************************************************
+ * TLan_HandleRxEOF
+ *
+ * Returns:
+ * 1
+ * Parms:
+ * dev Device assigned the IRQ that was
+ * raised.
+ * host_int The contents of the HOST_INT
+ * port.
+ *
+ * This function handles the Rx EOF interrupt which
+ * indicates a frame has been received by the adapter from
+ * the net and the frame has been transferred to memory.
+ * The function determines the bounce buffer the frame has
+ * been loaded into, creates a new sk_buff big enough to
+ * hold the frame, and sends it to protocol stack. It
+ * then resets the used buffer and appends it to the end
+ * of the list. If the frame was the last in the Rx
+ * channel (EOC), the function restarts the receive channel
+ * by sending an Rx Go command to the adapter. Then it
+ * activates/continues the activity LED.
+ *
+ **************************************************************/
+
+static u32 tlan_handle_rx_eof(struct net_device *dev, u16 host_int)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u32 ack = 0;
int eoc = 0;
- TLanList *head_list;
+ struct tlan_list *head_list;
struct sk_buff *skb;
- TLanList *tail_list;
- u16 tmpCStat;
+ struct tlan_list *tail_list;
+ u16 tmp_c_stat;
dma_addr_t head_list_phys;
- TLAN_DBG( TLAN_DEBUG_RX, "RECEIVE: Handling RX EOF (Head=%d Tail=%d)\n",
- priv->rxHead, priv->rxTail );
- head_list = priv->rxList + priv->rxHead;
- head_list_phys = priv->rxListDMA + sizeof(TLanList) * priv->rxHead;
+ TLAN_DBG(TLAN_DEBUG_RX, "RECEIVE: handling RX EOF (Head=%d Tail=%d)\n",
+ priv->rx_head, priv->rx_tail);
+ head_list = priv->rx_list + priv->rx_head;
+ head_list_phys =
+ priv->rx_list_dma + sizeof(struct tlan_list)*priv->rx_head;
- while (((tmpCStat = head_list->cStat) & TLAN_CSTAT_FRM_CMP) && (ack < 255)) {
- dma_addr_t frameDma = head_list->buffer[0].address;
- u32 frameSize = head_list->frameSize;
+ while (((tmp_c_stat = head_list->c_stat) & TLAN_CSTAT_FRM_CMP)
+ && (ack < 255)) {
+ dma_addr_t frame_dma = head_list->buffer[0].address;
+ u32 frame_size = head_list->frame_size;
struct sk_buff *new_skb;
ack++;
- if (tmpCStat & TLAN_CSTAT_EOC)
+ if (tmp_c_stat & TLAN_CSTAT_EOC)
eoc = 1;
new_skb = netdev_alloc_skb_ip_align(dev,
TLAN_MAX_FRAME_SIZE + 5);
- if ( !new_skb )
+ if (!new_skb)
goto drop_and_reuse;
- skb = TLan_GetSKB(head_list);
- pci_unmap_single(priv->pciDev, frameDma,
+ skb = tlan_get_skb(head_list);
+ pci_unmap_single(priv->pci_dev, frame_dma,
TLAN_MAX_FRAME_SIZE, PCI_DMA_FROMDEVICE);
- skb_put( skb, frameSize );
+ skb_put(skb, frame_size);
- dev->stats.rx_bytes += frameSize;
+ dev->stats.rx_bytes += frame_size;
- skb->protocol = eth_type_trans( skb, dev );
- netif_rx( skb );
+ skb->protocol = eth_type_trans(skb, dev);
+ netif_rx(skb);
- head_list->buffer[0].address = pci_map_single(priv->pciDev,
- new_skb->data,
- TLAN_MAX_FRAME_SIZE,
- PCI_DMA_FROMDEVICE);
+ head_list->buffer[0].address =
+ pci_map_single(priv->pci_dev, new_skb->data,
+ TLAN_MAX_FRAME_SIZE, PCI_DMA_FROMDEVICE);
- TLan_StoreSKB(head_list, new_skb);
+ tlan_store_skb(head_list, new_skb);
drop_and_reuse:
head_list->forward = 0;
- head_list->cStat = 0;
- tail_list = priv->rxList + priv->rxTail;
+ head_list->c_stat = 0;
+ tail_list = priv->rx_list + priv->rx_tail;
tail_list->forward = head_list_phys;
- CIRC_INC( priv->rxHead, TLAN_NUM_RX_LISTS );
- CIRC_INC( priv->rxTail, TLAN_NUM_RX_LISTS );
- head_list = priv->rxList + priv->rxHead;
- head_list_phys = priv->rxListDMA + sizeof(TLanList) * priv->rxHead;
+ CIRC_INC(priv->rx_head, TLAN_NUM_RX_LISTS);
+ CIRC_INC(priv->rx_tail, TLAN_NUM_RX_LISTS);
+ head_list = priv->rx_list + priv->rx_head;
+ head_list_phys = priv->rx_list_dma
+ + sizeof(struct tlan_list)*priv->rx_head;
}
if (!ack)
- printk(KERN_INFO "TLAN: Received interrupt for uncompleted RX frame.\n");
-
-
- if ( eoc ) {
- TLAN_DBG( TLAN_DEBUG_RX,
- "RECEIVE: Handling RX EOC (Head=%d Tail=%d)\n",
- priv->rxHead, priv->rxTail );
- head_list = priv->rxList + priv->rxHead;
- head_list_phys = priv->rxListDMA + sizeof(TLanList) * priv->rxHead;
- outl(head_list_phys, dev->base_addr + TLAN_CH_PARM );
+ printk(KERN_INFO
+ "TLAN: Received interrupt for uncompleted RX frame.\n");
+
+
+ if (eoc) {
+ TLAN_DBG(TLAN_DEBUG_RX,
+ "RECEIVE: handling RX EOC (Head=%d Tail=%d)\n",
+ priv->rx_head, priv->rx_tail);
+ head_list = priv->rx_list + priv->rx_head;
+ head_list_phys = priv->rx_list_dma
+ + sizeof(struct tlan_list)*priv->rx_head;
+ outl(head_list_phys, dev->base_addr + TLAN_CH_PARM);
ack |= TLAN_HC_GO | TLAN_HC_RT;
- priv->rxEocCount++;
+ priv->rx_eoc_count++;
}
- if ( priv->adapter->flags & TLAN_ADAPTER_ACTIVITY_LED ) {
- TLan_DioWrite8( dev->base_addr,
- TLAN_LED_REG, TLAN_LED_LINK | TLAN_LED_ACT );
- if ( priv->timer.function == NULL ) {
- priv->timer.function = TLan_Timer;
+ if (priv->adapter->flags & TLAN_ADAPTER_ACTIVITY_LED) {
+ tlan_dio_write8(dev->base_addr,
+ TLAN_LED_REG, TLAN_LED_LINK | TLAN_LED_ACT);
+ if (priv->timer.function == NULL) {
+ priv->timer.function = tlan_timer;
priv->timer.data = (unsigned long) dev;
priv->timer.expires = jiffies + TLAN_TIMER_ACT_DELAY;
- priv->timerSetAt = jiffies;
- priv->timerType = TLAN_TIMER_ACTIVITY;
+ priv->timer_set_at = jiffies;
+ priv->timer_type = TLAN_TIMER_ACTIVITY;
add_timer(&priv->timer);
- } else if ( priv->timerType == TLAN_TIMER_ACTIVITY ) {
- priv->timerSetAt = jiffies;
+ } else if (priv->timer_type == TLAN_TIMER_ACTIVITY) {
+ priv->timer_set_at = jiffies;
}
}
return ack;
-} /* TLan_HandleRxEOF */
+}
- /***************************************************************
- * TLan_HandleDummy
- *
- * Returns:
- * 1
- * Parms:
- * dev Device assigned the IRQ that was
- * raised.
- * host_int The contents of the HOST_INT
- * port.
- *
- * This function handles the Dummy interrupt, which is
- * raised whenever a test interrupt is generated by setting
- * the Req_Int bit of HOST_CMD to 1.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_handle_dummy
+ *
+ * Returns:
+ * 1
+ * Parms:
+ * dev Device assigned the IRQ that was
+ * raised.
+ * host_int The contents of the HOST_INT
+ * port.
+ *
+ * This function handles the Dummy interrupt, which is
+ * raised whenever a test interrupt is generated by setting
+ * the Req_Int bit of HOST_CMD to 1.
+ *
+ **************************************************************/
-static u32 TLan_HandleDummy( struct net_device *dev, u16 host_int )
+static u32 tlan_handle_dummy(struct net_device *dev, u16 host_int)
{
- printk( "TLAN: Test interrupt on %s.\n", dev->name );
+ pr_info("TLAN: Test interrupt on %s.\n", dev->name);
return 1;
-} /* TLan_HandleDummy */
+}
- /***************************************************************
- * TLan_HandleTxEOC
- *
- * Returns:
- * 1
- * Parms:
- * dev Device assigned the IRQ that was
- * raised.
- * host_int The contents of the HOST_INT
- * port.
- *
- * This driver is structured to determine EOC occurrences by
- * reading the CSTAT member of the list structure. Tx EOC
- * interrupts are disabled via the DIO INTDIS register.
- * However, TLAN chips before revision 3.0 didn't have this
- * functionality, so process EOC events if this is the
- * case.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_handle_tx_eoc
+ *
+ * Returns:
+ * 1
+ * Parms:
+ * dev Device assigned the IRQ that was
+ * raised.
+ * host_int The contents of the HOST_INT
+ * port.
+ *
+ * This driver is structured to determine EOC occurrences by
+ * reading the CSTAT member of the list structure. Tx EOC
+ * interrupts are disabled via the DIO INTDIS register.
+ * However, TLAN chips before revision 3.0 didn't have this
+ * functionality, so process EOC events if this is the
+ * case.
+ *
+ **************************************************************/
-static u32 TLan_HandleTxEOC( struct net_device *dev, u16 host_int )
+static u32 tlan_handle_tx_eoc(struct net_device *dev, u16 host_int)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
- TLanList *head_list;
+ struct tlan_priv *priv = netdev_priv(dev);
+ struct tlan_list *head_list;
dma_addr_t head_list_phys;
u32 ack = 1;
host_int = 0;
- if ( priv->tlanRev < 0x30 ) {
- TLAN_DBG( TLAN_DEBUG_TX,
- "TRANSMIT: Handling TX EOC (Head=%d Tail=%d) -- IRQ\n",
- priv->txHead, priv->txTail );
- head_list = priv->txList + priv->txHead;
- head_list_phys = priv->txListDMA + sizeof(TLanList) * priv->txHead;
- if ( ( head_list->cStat & TLAN_CSTAT_READY ) == TLAN_CSTAT_READY ) {
+ if (priv->tlan_rev < 0x30) {
+ TLAN_DBG(TLAN_DEBUG_TX,
+ "TRANSMIT: handling TX EOC (Head=%d Tail=%d) -- IRQ\n",
+ priv->tx_head, priv->tx_tail);
+ head_list = priv->tx_list + priv->tx_head;
+ head_list_phys = priv->tx_list_dma
+ + sizeof(struct tlan_list)*priv->tx_head;
+ if (head_list->c_stat & TLAN_CSTAT_READY) {
netif_stop_queue(dev);
- outl( head_list_phys, dev->base_addr + TLAN_CH_PARM );
+ outl(head_list_phys, dev->base_addr + TLAN_CH_PARM);
ack |= TLAN_HC_GO;
} else {
- priv->txInProgress = 0;
+ priv->tx_in_progress = 0;
}
}
return ack;
-} /* TLan_HandleTxEOC */
+}
- /***************************************************************
- * TLan_HandleStatusCheck
- *
- * Returns:
- * 0 if Adapter check, 1 if Network Status check.
- * Parms:
- * dev Device assigned the IRQ that was
- * raised.
- * host_int The contents of the HOST_INT
- * port.
- *
- * This function handles Adapter Check/Network Status
- * interrupts generated by the adapter. It checks the
- * vector in the HOST_INT register to determine if it is
- * an Adapter Check interrupt. If so, it resets the
- * adapter. Otherwise it clears the status registers
- * and services the PHY.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_handle_status_check
+ *
+ * Returns:
+ * 0 if Adapter check, 1 if Network Status check.
+ * Parms:
+ * dev Device assigned the IRQ that was
+ * raised.
+ * host_int The contents of the HOST_INT
+ * port.
+ *
+ * This function handles Adapter Check/Network Status
+ * interrupts generated by the adapter. It checks the
+ * vector in the HOST_INT register to determine if it is
+ * an Adapter Check interrupt. If so, it resets the
+ * adapter. Otherwise it clears the status registers
+ * and services the PHY.
+ *
+ **************************************************************/
-static u32 TLan_HandleStatusCheck( struct net_device *dev, u16 host_int )
+static u32 tlan_handle_status_check(struct net_device *dev, u16 host_int)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u32 ack;
u32 error;
u8 net_sts;
u16 tlphy_sts;
ack = 1;
- if ( host_int & TLAN_HI_IV_MASK ) {
- netif_stop_queue( dev );
- error = inl( dev->base_addr + TLAN_CH_PARM );
- printk( "TLAN: %s: Adaptor Error = 0x%x\n", dev->name, error );
- TLan_ReadAndClearStats( dev, TLAN_RECORD );
- outl( TLAN_HC_AD_RST, dev->base_addr + TLAN_HOST_CMD );
+ if (host_int & TLAN_HI_IV_MASK) {
+ netif_stop_queue(dev);
+ error = inl(dev->base_addr + TLAN_CH_PARM);
+ pr_info("TLAN: %s: Adaptor Error = 0x%x\n", dev->name, error);
+ tlan_read_and_clear_stats(dev, TLAN_RECORD);
+ outl(TLAN_HC_AD_RST, dev->base_addr + TLAN_HOST_CMD);
schedule_work(&priv->tlan_tqueue);
netif_wake_queue(dev);
ack = 0;
} else {
- TLAN_DBG( TLAN_DEBUG_GNRL, "%s: Status Check\n", dev->name );
- phy = priv->phy[priv->phyNum];
-
- net_sts = TLan_DioRead8( dev->base_addr, TLAN_NET_STS );
- if ( net_sts ) {
- TLan_DioWrite8( dev->base_addr, TLAN_NET_STS, net_sts );
- TLAN_DBG( TLAN_DEBUG_GNRL, "%s: Net_Sts = %x\n",
- dev->name, (unsigned) net_sts );
+ TLAN_DBG(TLAN_DEBUG_GNRL, "%s: Status Check\n", dev->name);
+ phy = priv->phy[priv->phy_num];
+
+ net_sts = tlan_dio_read8(dev->base_addr, TLAN_NET_STS);
+ if (net_sts) {
+ tlan_dio_write8(dev->base_addr, TLAN_NET_STS, net_sts);
+ TLAN_DBG(TLAN_DEBUG_GNRL, "%s: Net_Sts = %x\n",
+ dev->name, (unsigned) net_sts);
}
- if ( ( net_sts & TLAN_NET_STS_MIRQ ) && ( priv->phyNum == 0 ) ) {
- TLan_MiiReadReg( dev, phy, TLAN_TLPHY_STS, &tlphy_sts );
- TLan_MiiReadReg( dev, phy, TLAN_TLPHY_CTL, &tlphy_ctl );
- if ( ! ( tlphy_sts & TLAN_TS_POLOK ) &&
- ! ( tlphy_ctl & TLAN_TC_SWAPOL ) ) {
- tlphy_ctl |= TLAN_TC_SWAPOL;
- TLan_MiiWriteReg( dev, phy, TLAN_TLPHY_CTL, tlphy_ctl);
- } else if ( ( tlphy_sts & TLAN_TS_POLOK ) &&
- ( tlphy_ctl & TLAN_TC_SWAPOL ) ) {
- tlphy_ctl &= ~TLAN_TC_SWAPOL;
- TLan_MiiWriteReg( dev, phy, TLAN_TLPHY_CTL, tlphy_ctl);
- }
-
- if (debug) {
- TLan_PhyPrint( dev );
+ if ((net_sts & TLAN_NET_STS_MIRQ) && (priv->phy_num == 0)) {
+ tlan_mii_read_reg(dev, phy, TLAN_TLPHY_STS, &tlphy_sts);
+ tlan_mii_read_reg(dev, phy, TLAN_TLPHY_CTL, &tlphy_ctl);
+ if (!(tlphy_sts & TLAN_TS_POLOK) &&
+ !(tlphy_ctl & TLAN_TC_SWAPOL)) {
+ tlphy_ctl |= TLAN_TC_SWAPOL;
+ tlan_mii_write_reg(dev, phy, TLAN_TLPHY_CTL,
+ tlphy_ctl);
+ } else if ((tlphy_sts & TLAN_TS_POLOK) &&
+ (tlphy_ctl & TLAN_TC_SWAPOL)) {
+ tlphy_ctl &= ~TLAN_TC_SWAPOL;
+ tlan_mii_write_reg(dev, phy, TLAN_TLPHY_CTL,
+ tlphy_ctl);
}
+
+ if (debug)
+ tlan_phy_print(dev);
}
}
return ack;
-} /* TLan_HandleStatusCheck */
+}
- /***************************************************************
- * TLan_HandleRxEOC
- *
- * Returns:
- * 1
- * Parms:
- * dev Device assigned the IRQ that was
- * raised.
- * host_int The contents of the HOST_INT
- * port.
- *
- * This driver is structured to determine EOC occurrences by
- * reading the CSTAT member of the list structure. Rx EOC
- * interrupts are disabled via the DIO INTDIS register.
- * However, TLAN chips before revision 3.0 didn't have this
- * CSTAT member or a INTDIS register, so if this chip is
- * pre-3.0, process EOC interrupts normally.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_handle_rx_eoc
+ *
+ * Returns:
+ * 1
+ * Parms:
+ * dev Device assigned the IRQ that was
+ * raised.
+ * host_int The contents of the HOST_INT
+ * port.
+ *
+ * This driver is structured to determine EOC occurrences by
+ * reading the CSTAT member of the list structure. Rx EOC
+ * interrupts are disabled via the DIO INTDIS register.
+ * However, TLAN chips before revision 3.0 didn't have this
+ * CSTAT member or a INTDIS register, so if this chip is
+ * pre-3.0, process EOC interrupts normally.
+ *
+ **************************************************************/
-static u32 TLan_HandleRxEOC( struct net_device *dev, u16 host_int )
+static u32 tlan_handle_rx_eoc(struct net_device *dev, u16 host_int)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
dma_addr_t head_list_phys;
u32 ack = 1;
- if ( priv->tlanRev < 0x30 ) {
- TLAN_DBG( TLAN_DEBUG_RX,
- "RECEIVE: Handling RX EOC (Head=%d Tail=%d) -- IRQ\n",
- priv->rxHead, priv->rxTail );
- head_list_phys = priv->rxListDMA + sizeof(TLanList) * priv->rxHead;
- outl( head_list_phys, dev->base_addr + TLAN_CH_PARM );
+ if (priv->tlan_rev < 0x30) {
+ TLAN_DBG(TLAN_DEBUG_RX,
+ "RECEIVE: Handling RX EOC (head=%d tail=%d) -- IRQ\n",
+ priv->rx_head, priv->rx_tail);
+ head_list_phys = priv->rx_list_dma
+ + sizeof(struct tlan_list)*priv->rx_head;
+ outl(head_list_phys, dev->base_addr + TLAN_CH_PARM);
ack |= TLAN_HC_GO | TLAN_HC_RT;
- priv->rxEocCount++;
+ priv->rx_eoc_count++;
}
return ack;
-} /* TLan_HandleRxEOC */
+}
/*****************************************************************************
******************************************************************************
- ThunderLAN Driver Timer Function
+ThunderLAN driver timer function
******************************************************************************
*****************************************************************************/
- /***************************************************************
- * TLan_Timer
- *
- * Returns:
- * Nothing
- * Parms:
- * data A value given to add timer when
- * add_timer was called.
- *
- * This function handles timed functionality for the
- * TLAN driver. The two current timer uses are for
- * delaying for autonegotionation and driving the ACT LED.
- * - Autonegotiation requires being allowed about
- * 2 1/2 seconds before attempting to transmit a
- * packet. It would be a very bad thing to hang
- * the kernel this long, so the driver doesn't
- * allow transmission 'til after this time, for
- * certain PHYs. It would be much nicer if all
- * PHYs were interrupt-capable like the internal
- * PHY.
- * - The ACT LED, which shows adapter activity, is
- * driven by the driver, and so must be left on
- * for a short period to power up the LED so it
- * can be seen. This delay can be changed by
- * changing the TLAN_TIMER_ACT_DELAY in tlan.h,
- * if desired. 100 ms produces a slightly
- * sluggish response.
- *
- **************************************************************/
-
-static void TLan_Timer( unsigned long data )
+/***************************************************************
+ * tlan_timer
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * data A value given to add timer when
+ * add_timer was called.
+ *
+ * This function handles timed functionality for the
+ * TLAN driver. The two current timer uses are for
+ * delaying for autonegotionation and driving the ACT LED.
+ * - Autonegotiation requires being allowed about
+ * 2 1/2 seconds before attempting to transmit a
+ * packet. It would be a very bad thing to hang
+ * the kernel this long, so the driver doesn't
+ * allow transmission 'til after this time, for
+ * certain PHYs. It would be much nicer if all
+ * PHYs were interrupt-capable like the internal
+ * PHY.
+ * - The ACT LED, which shows adapter activity, is
+ * driven by the driver, and so must be left on
+ * for a short period to power up the LED so it
+ * can be seen. This delay can be changed by
+ * changing the TLAN_TIMER_ACT_DELAY in tlan.h,
+ * if desired. 100 ms produces a slightly
+ * sluggish response.
+ *
+ **************************************************************/
+
+static void tlan_timer(unsigned long data)
{
struct net_device *dev = (struct net_device *) data;
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u32 elapsed;
unsigned long flags = 0;
priv->timer.function = NULL;
- switch ( priv->timerType ) {
+ switch (priv->timer_type) {
#ifdef MONITOR
- case TLAN_TIMER_LINK_BEAT:
- TLan_PhyMonitor( dev );
- break;
+ case TLAN_TIMER_LINK_BEAT:
+ tlan_phy_monitor(dev);
+ break;
#endif
- case TLAN_TIMER_PHY_PDOWN:
- TLan_PhyPowerDown( dev );
- break;
- case TLAN_TIMER_PHY_PUP:
- TLan_PhyPowerUp( dev );
- break;
- case TLAN_TIMER_PHY_RESET:
- TLan_PhyReset( dev );
- break;
- case TLAN_TIMER_PHY_START_LINK:
- TLan_PhyStartLink( dev );
- break;
- case TLAN_TIMER_PHY_FINISH_AN:
- TLan_PhyFinishAutoNeg( dev );
- break;
- case TLAN_TIMER_FINISH_RESET:
- TLan_FinishReset( dev );
- break;
- case TLAN_TIMER_ACTIVITY:
- spin_lock_irqsave(&priv->lock, flags);
- if ( priv->timer.function == NULL ) {
- elapsed = jiffies - priv->timerSetAt;
- if ( elapsed >= TLAN_TIMER_ACT_DELAY ) {
- TLan_DioWrite8( dev->base_addr,
- TLAN_LED_REG, TLAN_LED_LINK );
- } else {
- priv->timer.function = TLan_Timer;
- priv->timer.expires = priv->timerSetAt
- + TLAN_TIMER_ACT_DELAY;
- spin_unlock_irqrestore(&priv->lock, flags);
- add_timer( &priv->timer );
- break;
- }
+ case TLAN_TIMER_PHY_PDOWN:
+ tlan_phy_power_down(dev);
+ break;
+ case TLAN_TIMER_PHY_PUP:
+ tlan_phy_power_up(dev);
+ break;
+ case TLAN_TIMER_PHY_RESET:
+ tlan_phy_reset(dev);
+ break;
+ case TLAN_TIMER_PHY_START_LINK:
+ tlan_phy_start_link(dev);
+ break;
+ case TLAN_TIMER_PHY_FINISH_AN:
+ tlan_phy_finish_auto_neg(dev);
+ break;
+ case TLAN_TIMER_FINISH_RESET:
+ tlan_finish_reset(dev);
+ break;
+ case TLAN_TIMER_ACTIVITY:
+ spin_lock_irqsave(&priv->lock, flags);
+ if (priv->timer.function == NULL) {
+ elapsed = jiffies - priv->timer_set_at;
+ if (elapsed >= TLAN_TIMER_ACT_DELAY) {
+ tlan_dio_write8(dev->base_addr,
+ TLAN_LED_REG, TLAN_LED_LINK);
+ } else {
+ priv->timer.function = tlan_timer;
+ priv->timer.expires = priv->timer_set_at
+ + TLAN_TIMER_ACT_DELAY;
+ spin_unlock_irqrestore(&priv->lock, flags);
+ add_timer(&priv->timer);
+ break;
}
- spin_unlock_irqrestore(&priv->lock, flags);
- break;
- default:
- break;
+ }
+ spin_unlock_irqrestore(&priv->lock, flags);
+ break;
+ default:
+ break;
}
-} /* TLan_Timer */
+}
/*****************************************************************************
******************************************************************************
- ThunderLAN Driver Adapter Related Routines
+ThunderLAN driver adapter related routines
******************************************************************************
*****************************************************************************/
- /***************************************************************
- * TLan_ResetLists
- *
- * Returns:
- * Nothing
- * Parms:
- * dev The device structure with the list
- * stuctures to be reset.
- *
- * This routine sets the variables associated with managing
- * the TLAN lists to their initial values.
- *
- **************************************************************/
-
-static void TLan_ResetLists( struct net_device *dev )
+/***************************************************************
+ * tlan_reset_lists
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * dev The device structure with the list
+ * stuctures to be reset.
+ *
+ * This routine sets the variables associated with managing
+ * the TLAN lists to their initial values.
+ *
+ **************************************************************/
+
+static void tlan_reset_lists(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
int i;
- TLanList *list;
+ struct tlan_list *list;
dma_addr_t list_phys;
struct sk_buff *skb;
- priv->txHead = 0;
- priv->txTail = 0;
- for ( i = 0; i < TLAN_NUM_TX_LISTS; i++ ) {
- list = priv->txList + i;
- list->cStat = TLAN_CSTAT_UNUSED;
+ priv->tx_head = 0;
+ priv->tx_tail = 0;
+ for (i = 0; i < TLAN_NUM_TX_LISTS; i++) {
+ list = priv->tx_list + i;
+ list->c_stat = TLAN_CSTAT_UNUSED;
list->buffer[0].address = 0;
list->buffer[2].count = 0;
list->buffer[2].address = 0;
list->buffer[9].address = 0;
}
- priv->rxHead = 0;
- priv->rxTail = TLAN_NUM_RX_LISTS - 1;
- for ( i = 0; i < TLAN_NUM_RX_LISTS; i++ ) {
- list = priv->rxList + i;
- list_phys = priv->rxListDMA + sizeof(TLanList) * i;
- list->cStat = TLAN_CSTAT_READY;
- list->frameSize = TLAN_MAX_FRAME_SIZE;
+ priv->rx_head = 0;
+ priv->rx_tail = TLAN_NUM_RX_LISTS - 1;
+ for (i = 0; i < TLAN_NUM_RX_LISTS; i++) {
+ list = priv->rx_list + i;
+ list_phys = priv->rx_list_dma + sizeof(struct tlan_list)*i;
+ list->c_stat = TLAN_CSTAT_READY;
+ list->frame_size = TLAN_MAX_FRAME_SIZE;
list->buffer[0].count = TLAN_MAX_FRAME_SIZE | TLAN_LAST_BUFFER;
skb = netdev_alloc_skb_ip_align(dev, TLAN_MAX_FRAME_SIZE + 5);
- if ( !skb ) {
- pr_err("TLAN: out of memory for received data.\n" );
+ if (!skb) {
+ pr_err("TLAN: out of memory for received data.\n");
break;
}
- list->buffer[0].address = pci_map_single(priv->pciDev,
+ list->buffer[0].address = pci_map_single(priv->pci_dev,
skb->data,
TLAN_MAX_FRAME_SIZE,
PCI_DMA_FROMDEVICE);
- TLan_StoreSKB(list, skb);
+ tlan_store_skb(list, skb);
list->buffer[1].count = 0;
list->buffer[1].address = 0;
- list->forward = list_phys + sizeof(TLanList);
+ list->forward = list_phys + sizeof(struct tlan_list);
}
/* in case ran out of memory early, clear bits */
while (i < TLAN_NUM_RX_LISTS) {
- TLan_StoreSKB(priv->rxList + i, NULL);
+ tlan_store_skb(priv->rx_list + i, NULL);
++i;
}
list->forward = 0;
-} /* TLan_ResetLists */
+}
-static void TLan_FreeLists( struct net_device *dev )
+static void tlan_free_lists(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
int i;
- TLanList *list;
+ struct tlan_list *list;
struct sk_buff *skb;
- for ( i = 0; i < TLAN_NUM_TX_LISTS; i++ ) {
- list = priv->txList + i;
- skb = TLan_GetSKB(list);
- if ( skb ) {
+ for (i = 0; i < TLAN_NUM_TX_LISTS; i++) {
+ list = priv->tx_list + i;
+ skb = tlan_get_skb(list);
+ if (skb) {
pci_unmap_single(
- priv->pciDev,
+ priv->pci_dev,
list->buffer[0].address,
max(skb->len,
(unsigned int)TLAN_MIN_FRAME_SIZE),
PCI_DMA_TODEVICE);
- dev_kfree_skb_any( skb );
+ dev_kfree_skb_any(skb);
list->buffer[8].address = 0;
list->buffer[9].address = 0;
}
}
- for ( i = 0; i < TLAN_NUM_RX_LISTS; i++ ) {
- list = priv->rxList + i;
- skb = TLan_GetSKB(list);
- if ( skb ) {
- pci_unmap_single(priv->pciDev,
+ for (i = 0; i < TLAN_NUM_RX_LISTS; i++) {
+ list = priv->rx_list + i;
+ skb = tlan_get_skb(list);
+ if (skb) {
+ pci_unmap_single(priv->pci_dev,
list->buffer[0].address,
TLAN_MAX_FRAME_SIZE,
PCI_DMA_FROMDEVICE);
- dev_kfree_skb_any( skb );
+ dev_kfree_skb_any(skb);
list->buffer[8].address = 0;
list->buffer[9].address = 0;
}
}
-} /* TLan_FreeLists */
+}
- /***************************************************************
- * TLan_PrintDio
- *
- * Returns:
- * Nothing
- * Parms:
- * io_base Base IO port of the device of
- * which to print DIO registers.
- *
- * This function prints out all the internal (DIO)
- * registers of a TLAN chip.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_print_dio
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * io_base Base IO port of the device of
+ * which to print DIO registers.
+ *
+ * This function prints out all the internal (DIO)
+ * registers of a TLAN chip.
+ *
+ **************************************************************/
-static void TLan_PrintDio( u16 io_base )
+static void tlan_print_dio(u16 io_base)
{
u32 data0, data1;
int i;
- printk( "TLAN: Contents of internal registers for io base 0x%04hx.\n",
- io_base );
- printk( "TLAN: Off. +0 +4\n" );
- for ( i = 0; i < 0x4C; i+= 8 ) {
- data0 = TLan_DioRead32( io_base, i );
- data1 = TLan_DioRead32( io_base, i + 0x4 );
- printk( "TLAN: 0x%02x 0x%08x 0x%08x\n", i, data0, data1 );
+ pr_info("TLAN: Contents of internal registers for io base 0x%04hx.\n",
+ io_base);
+ pr_info("TLAN: Off. +0 +4\n");
+ for (i = 0; i < 0x4C; i += 8) {
+ data0 = tlan_dio_read32(io_base, i);
+ data1 = tlan_dio_read32(io_base, i + 0x4);
+ pr_info("TLAN: 0x%02x 0x%08x 0x%08x\n", i, data0, data1);
}
-} /* TLan_PrintDio */
+}
- /***************************************************************
- * TLan_PrintList
- *
- * Returns:
- * Nothing
- * Parms:
- * list A pointer to the TLanList structure to
- * be printed.
- * type A string to designate type of list,
- * "Rx" or "Tx".
- * num The index of the list.
- *
- * This function prints out the contents of the list
- * pointed to by the list parameter.
- *
- **************************************************************/
+/***************************************************************
+ * TLan_PrintList
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * list A pointer to the struct tlan_list structure to
+ * be printed.
+ * type A string to designate type of list,
+ * "Rx" or "Tx".
+ * num The index of the list.
+ *
+ * This function prints out the contents of the list
+ * pointed to by the list parameter.
+ *
+ **************************************************************/
-static void TLan_PrintList( TLanList *list, char *type, int num)
+static void tlan_print_list(struct tlan_list *list, char *type, int num)
{
int i;
- printk( "TLAN: %s List %d at %p\n", type, num, list );
- printk( "TLAN: Forward = 0x%08x\n", list->forward );
- printk( "TLAN: CSTAT = 0x%04hx\n", list->cStat );
- printk( "TLAN: Frame Size = 0x%04hx\n", list->frameSize );
- /* for ( i = 0; i < 10; i++ ) { */
- for ( i = 0; i < 2; i++ ) {
- printk( "TLAN: Buffer[%d].count, addr = 0x%08x, 0x%08x\n",
- i, list->buffer[i].count, list->buffer[i].address );
+ pr_info("TLAN: %s List %d at %p\n", type, num, list);
+ pr_info("TLAN: Forward = 0x%08x\n", list->forward);
+ pr_info("TLAN: CSTAT = 0x%04hx\n", list->c_stat);
+ pr_info("TLAN: Frame Size = 0x%04hx\n", list->frame_size);
+ /* for (i = 0; i < 10; i++) { */
+ for (i = 0; i < 2; i++) {
+ pr_info("TLAN: Buffer[%d].count, addr = 0x%08x, 0x%08x\n",
+ i, list->buffer[i].count, list->buffer[i].address);
}
-} /* TLan_PrintList */
+}
- /***************************************************************
- * TLan_ReadAndClearStats
- *
- * Returns:
- * Nothing
- * Parms:
- * dev Pointer to device structure of adapter
- * to which to read stats.
- * record Flag indicating whether to add
- *
- * This functions reads all the internal status registers
- * of the TLAN chip, which clears them as a side effect.
- * It then either adds the values to the device's status
- * struct, or discards them, depending on whether record
- * is TLAN_RECORD (!=0) or TLAN_IGNORE (==0).
- *
- **************************************************************/
+/***************************************************************
+ * tlan_read_and_clear_stats
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * dev Pointer to device structure of adapter
+ * to which to read stats.
+ * record Flag indicating whether to add
+ *
+ * This functions reads all the internal status registers
+ * of the TLAN chip, which clears them as a side effect.
+ * It then either adds the values to the device's status
+ * struct, or discards them, depending on whether record
+ * is TLAN_RECORD (!=0) or TLAN_IGNORE (==0).
+ *
+ **************************************************************/
-static void TLan_ReadAndClearStats( struct net_device *dev, int record )
+static void tlan_read_and_clear_stats(struct net_device *dev, int record)
{
u32 tx_good, tx_under;
u32 rx_good, rx_over;
u32 multi_col, single_col;
u32 excess_col, late_col, loss;
- outw( TLAN_GOOD_TX_FRMS, dev->base_addr + TLAN_DIO_ADR );
- tx_good = inb( dev->base_addr + TLAN_DIO_DATA );
- tx_good += inb( dev->base_addr + TLAN_DIO_DATA + 1 ) << 8;
- tx_good += inb( dev->base_addr + TLAN_DIO_DATA + 2 ) << 16;
- tx_under = inb( dev->base_addr + TLAN_DIO_DATA + 3 );
-
- outw( TLAN_GOOD_RX_FRMS, dev->base_addr + TLAN_DIO_ADR );
- rx_good = inb( dev->base_addr + TLAN_DIO_DATA );
- rx_good += inb( dev->base_addr + TLAN_DIO_DATA + 1 ) << 8;
- rx_good += inb( dev->base_addr + TLAN_DIO_DATA + 2 ) << 16;
- rx_over = inb( dev->base_addr + TLAN_DIO_DATA + 3 );
-
- outw( TLAN_DEFERRED_TX, dev->base_addr + TLAN_DIO_ADR );
- def_tx = inb( dev->base_addr + TLAN_DIO_DATA );
- def_tx += inb( dev->base_addr + TLAN_DIO_DATA + 1 ) << 8;
- crc = inb( dev->base_addr + TLAN_DIO_DATA + 2 );
- code = inb( dev->base_addr + TLAN_DIO_DATA + 3 );
-
- outw( TLAN_MULTICOL_FRMS, dev->base_addr + TLAN_DIO_ADR );
- multi_col = inb( dev->base_addr + TLAN_DIO_DATA );
- multi_col += inb( dev->base_addr + TLAN_DIO_DATA + 1 ) << 8;
- single_col = inb( dev->base_addr + TLAN_DIO_DATA + 2 );
- single_col += inb( dev->base_addr + TLAN_DIO_DATA + 3 ) << 8;
-
- outw( TLAN_EXCESSCOL_FRMS, dev->base_addr + TLAN_DIO_ADR );
- excess_col = inb( dev->base_addr + TLAN_DIO_DATA );
- late_col = inb( dev->base_addr + TLAN_DIO_DATA + 1 );
- loss = inb( dev->base_addr + TLAN_DIO_DATA + 2 );
-
- if ( record ) {
+ outw(TLAN_GOOD_TX_FRMS, dev->base_addr + TLAN_DIO_ADR);
+ tx_good = inb(dev->base_addr + TLAN_DIO_DATA);
+ tx_good += inb(dev->base_addr + TLAN_DIO_DATA + 1) << 8;
+ tx_good += inb(dev->base_addr + TLAN_DIO_DATA + 2) << 16;
+ tx_under = inb(dev->base_addr + TLAN_DIO_DATA + 3);
+
+ outw(TLAN_GOOD_RX_FRMS, dev->base_addr + TLAN_DIO_ADR);
+ rx_good = inb(dev->base_addr + TLAN_DIO_DATA);
+ rx_good += inb(dev->base_addr + TLAN_DIO_DATA + 1) << 8;
+ rx_good += inb(dev->base_addr + TLAN_DIO_DATA + 2) << 16;
+ rx_over = inb(dev->base_addr + TLAN_DIO_DATA + 3);
+
+ outw(TLAN_DEFERRED_TX, dev->base_addr + TLAN_DIO_ADR);
+ def_tx = inb(dev->base_addr + TLAN_DIO_DATA);
+ def_tx += inb(dev->base_addr + TLAN_DIO_DATA + 1) << 8;
+ crc = inb(dev->base_addr + TLAN_DIO_DATA + 2);
+ code = inb(dev->base_addr + TLAN_DIO_DATA + 3);
+
+ outw(TLAN_MULTICOL_FRMS, dev->base_addr + TLAN_DIO_ADR);
+ multi_col = inb(dev->base_addr + TLAN_DIO_DATA);
+ multi_col += inb(dev->base_addr + TLAN_DIO_DATA + 1) << 8;
+ single_col = inb(dev->base_addr + TLAN_DIO_DATA + 2);
+ single_col += inb(dev->base_addr + TLAN_DIO_DATA + 3) << 8;
+
+ outw(TLAN_EXCESSCOL_FRMS, dev->base_addr + TLAN_DIO_ADR);
+ excess_col = inb(dev->base_addr + TLAN_DIO_DATA);
+ late_col = inb(dev->base_addr + TLAN_DIO_DATA + 1);
+ loss = inb(dev->base_addr + TLAN_DIO_DATA + 2);
+
+ if (record) {
dev->stats.rx_packets += rx_good;
dev->stats.rx_errors += rx_over + crc + code;
dev->stats.tx_packets += tx_good;
dev->stats.tx_errors += tx_under + loss;
- dev->stats.collisions += multi_col + single_col + excess_col + late_col;
+ dev->stats.collisions += multi_col
+ + single_col + excess_col + late_col;
dev->stats.rx_over_errors += rx_over;
dev->stats.rx_crc_errors += crc;
dev->stats.tx_carrier_errors += loss;
}
-} /* TLan_ReadAndClearStats */
+}
- /***************************************************************
- * TLan_Reset
- *
- * Returns:
- * 0
- * Parms:
- * dev Pointer to device structure of adapter
- * to be reset.
- *
- * This function resets the adapter and it's physical
- * device. See Chap. 3, pp. 9-10 of the "ThunderLAN
- * Programmer's Guide" for details. The routine tries to
- * implement what is detailed there, though adjustments
- * have been made.
- *
- **************************************************************/
+/***************************************************************
+ * TLan_Reset
+ *
+ * Returns:
+ * 0
+ * Parms:
+ * dev Pointer to device structure of adapter
+ * to be reset.
+ *
+ * This function resets the adapter and it's physical
+ * device. See Chap. 3, pp. 9-10 of the "ThunderLAN
+ * Programmer's Guide" for details. The routine tries to
+ * implement what is detailed there, though adjustments
+ * have been made.
+ *
+ **************************************************************/
static void
-TLan_ResetAdapter( struct net_device *dev )
+tlan_reset_adapter(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
int i;
u32 addr;
u32 data;
u8 data8;
- priv->tlanFullDuplex = false;
- priv->phyOnline=0;
+ priv->tlan_full_duplex = false;
+ priv->phy_online = 0;
netif_carrier_off(dev);
/* 1. Assert reset bit. */
udelay(1000);
-/* 2. Turn off interrupts. ( Probably isn't necessary ) */
+/* 2. Turn off interrupts. (Probably isn't necessary) */
data = inl(dev->base_addr + TLAN_HOST_CMD);
data |= TLAN_HC_INT_OFF;
/* 3. Clear AREGs and HASHs. */
- for ( i = TLAN_AREG_0; i <= TLAN_HASH_2; i += 4 ) {
- TLan_DioWrite32( dev->base_addr, (u16) i, 0 );
- }
+ for (i = TLAN_AREG_0; i <= TLAN_HASH_2; i += 4)
+ tlan_dio_write32(dev->base_addr, (u16) i, 0);
/* 4. Setup NetConfig register. */
data = TLAN_NET_CFG_1FRAG | TLAN_NET_CFG_1CHAN | TLAN_NET_CFG_PHY_EN;
- TLan_DioWrite16( dev->base_addr, TLAN_NET_CONFIG, (u16) data );
+ tlan_dio_write16(dev->base_addr, TLAN_NET_CONFIG, (u16) data);
/* 5. Load Ld_Tmr and Ld_Thr in HOST_CMD. */
- outl( TLAN_HC_LD_TMR | 0x3f, dev->base_addr + TLAN_HOST_CMD );
- outl( TLAN_HC_LD_THR | 0x9, dev->base_addr + TLAN_HOST_CMD );
+ outl(TLAN_HC_LD_TMR | 0x3f, dev->base_addr + TLAN_HOST_CMD);
+ outl(TLAN_HC_LD_THR | 0x9, dev->base_addr + TLAN_HOST_CMD);
/* 6. Unreset the MII by setting NMRST (in NetSio) to 1. */
- outw( TLAN_NET_SIO, dev->base_addr + TLAN_DIO_ADR );
+ outw(TLAN_NET_SIO, dev->base_addr + TLAN_DIO_ADR);
addr = dev->base_addr + TLAN_DIO_DATA + TLAN_NET_SIO;
- TLan_SetBit( TLAN_NET_SIO_NMRST, addr );
+ tlan_set_bit(TLAN_NET_SIO_NMRST, addr);
/* 7. Setup the remaining registers. */
- if ( priv->tlanRev >= 0x30 ) {
+ if (priv->tlan_rev >= 0x30) {
data8 = TLAN_ID_TX_EOC | TLAN_ID_RX_EOC;
- TLan_DioWrite8( dev->base_addr, TLAN_INT_DIS, data8 );
+ tlan_dio_write8(dev->base_addr, TLAN_INT_DIS, data8);
}
- TLan_PhyDetect( dev );
+ tlan_phy_detect(dev);
data = TLAN_NET_CFG_1FRAG | TLAN_NET_CFG_1CHAN;
- if ( priv->adapter->flags & TLAN_ADAPTER_BIT_RATE_PHY ) {
+ if (priv->adapter->flags & TLAN_ADAPTER_BIT_RATE_PHY) {
data |= TLAN_NET_CFG_BIT;
- if ( priv->aui == 1 ) {
- TLan_DioWrite8( dev->base_addr, TLAN_ACOMMIT, 0x0a );
- } else if ( priv->duplex == TLAN_DUPLEX_FULL ) {
- TLan_DioWrite8( dev->base_addr, TLAN_ACOMMIT, 0x00 );
- priv->tlanFullDuplex = true;
+ if (priv->aui == 1) {
+ tlan_dio_write8(dev->base_addr, TLAN_ACOMMIT, 0x0a);
+ } else if (priv->duplex == TLAN_DUPLEX_FULL) {
+ tlan_dio_write8(dev->base_addr, TLAN_ACOMMIT, 0x00);
+ priv->tlan_full_duplex = true;
} else {
- TLan_DioWrite8( dev->base_addr, TLAN_ACOMMIT, 0x08 );
+ tlan_dio_write8(dev->base_addr, TLAN_ACOMMIT, 0x08);
}
}
- if ( priv->phyNum == 0 ) {
+ if (priv->phy_num == 0)
data |= TLAN_NET_CFG_PHY_EN;
- }
- TLan_DioWrite16( dev->base_addr, TLAN_NET_CONFIG, (u16) data );
+ tlan_dio_write16(dev->base_addr, TLAN_NET_CONFIG, (u16) data);
- if ( priv->adapter->flags & TLAN_ADAPTER_UNMANAGED_PHY ) {
- TLan_FinishReset( dev );
- } else {
- TLan_PhyPowerDown( dev );
- }
+ if (priv->adapter->flags & TLAN_ADAPTER_UNMANAGED_PHY)
+ tlan_finish_reset(dev);
+ else
+ tlan_phy_power_down(dev);
-} /* TLan_ResetAdapter */
+}
static void
-TLan_FinishReset( struct net_device *dev )
+tlan_finish_reset(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u8 data;
u32 phy;
u8 sio;
u16 status;
u16 partner;
u16 tlphy_ctl;
- u16 tlphy_par;
+ u16 tlphy_par;
u16 tlphy_id1, tlphy_id2;
- int i;
+ int i;
- phy = priv->phy[priv->phyNum];
+ phy = priv->phy[priv->phy_num];
data = TLAN_NET_CMD_NRESET | TLAN_NET_CMD_NWRAP;
- if ( priv->tlanFullDuplex ) {
+ if (priv->tlan_full_duplex)
data |= TLAN_NET_CMD_DUPLEX;
- }
- TLan_DioWrite8( dev->base_addr, TLAN_NET_CMD, data );
+ tlan_dio_write8(dev->base_addr, TLAN_NET_CMD, data);
data = TLAN_NET_MASK_MASK4 | TLAN_NET_MASK_MASK5;
- if ( priv->phyNum == 0 ) {
+ if (priv->phy_num == 0)
data |= TLAN_NET_MASK_MASK7;
- }
- TLan_DioWrite8( dev->base_addr, TLAN_NET_MASK, data );
- TLan_DioWrite16( dev->base_addr, TLAN_MAX_RX, ((1536)+7)&~7 );
- TLan_MiiReadReg( dev, phy, MII_GEN_ID_HI, &tlphy_id1 );
- TLan_MiiReadReg( dev, phy, MII_GEN_ID_LO, &tlphy_id2 );
+ tlan_dio_write8(dev->base_addr, TLAN_NET_MASK, data);
+ tlan_dio_write16(dev->base_addr, TLAN_MAX_RX, ((1536)+7)&~7);
+ tlan_mii_read_reg(dev, phy, MII_GEN_ID_HI, &tlphy_id1);
+ tlan_mii_read_reg(dev, phy, MII_GEN_ID_LO, &tlphy_id2);
- if ( ( priv->adapter->flags & TLAN_ADAPTER_UNMANAGED_PHY ) ||
- ( priv->aui ) ) {
+ if ((priv->adapter->flags & TLAN_ADAPTER_UNMANAGED_PHY) ||
+ (priv->aui)) {
status = MII_GS_LINK;
- printk( "TLAN: %s: Link forced.\n", dev->name );
+ pr_info("TLAN: %s: Link forced.\n", dev->name);
} else {
- TLan_MiiReadReg( dev, phy, MII_GEN_STS, &status );
- udelay( 1000 );
- TLan_MiiReadReg( dev, phy, MII_GEN_STS, &status );
- if ( (status & MII_GS_LINK) &&
- /* We only support link info on Nat.Sem. PHY's */
- (tlphy_id1 == NAT_SEM_ID1) &&
- (tlphy_id2 == NAT_SEM_ID2) ) {
- TLan_MiiReadReg( dev, phy, MII_AN_LPA, &partner );
- TLan_MiiReadReg( dev, phy, TLAN_TLPHY_PAR, &tlphy_par );
-
- printk( "TLAN: %s: Link active with ", dev->name );
+ tlan_mii_read_reg(dev, phy, MII_GEN_STS, &status);
+ udelay(1000);
+ tlan_mii_read_reg(dev, phy, MII_GEN_STS, &status);
+ if ((status & MII_GS_LINK) &&
+ /* We only support link info on Nat.Sem. PHY's */
+ (tlphy_id1 == NAT_SEM_ID1) &&
+ (tlphy_id2 == NAT_SEM_ID2)) {
+ tlan_mii_read_reg(dev, phy, MII_AN_LPA, &partner);
+ tlan_mii_read_reg(dev, phy, TLAN_TLPHY_PAR, &tlphy_par);
+
+ pr_info("TLAN: %s: Link active with ", dev->name);
if (!(tlphy_par & TLAN_PHY_AN_EN_STAT)) {
- printk( "forced 10%sMbps %s-Duplex\n",
- tlphy_par & TLAN_PHY_SPEED_100 ? "" : "0",
- tlphy_par & TLAN_PHY_DUPLEX_FULL ? "Full" : "Half");
+ pr_info("forced 10%sMbps %s-Duplex\n",
+ tlphy_par & TLAN_PHY_SPEED_100
+ ? "" : "0",
+ tlphy_par & TLAN_PHY_DUPLEX_FULL
+ ? "Full" : "Half");
} else {
- printk( "AutoNegotiation enabled, at 10%sMbps %s-Duplex\n",
- tlphy_par & TLAN_PHY_SPEED_100 ? "" : "0",
- tlphy_par & TLAN_PHY_DUPLEX_FULL ? "Full" : "Half");
- printk("TLAN: Partner capability: ");
- for (i = 5; i <= 10; i++)
- if (partner & (1<<i))
- printk("%s",media[i-5]);
+ pr_info("Autonegotiation enabled, at 10%sMbps %s-Duplex\n",
+ tlphy_par & TLAN_PHY_SPEED_100
+ ? "" : "0",
+ tlphy_par & TLAN_PHY_DUPLEX_FULL
+ ? "Full" : "half");
+ pr_info("TLAN: Partner capability: ");
+ for (i = 5; i <= 10; i++)
+ if (partner & (1<<i))
+ printk("%s", media[i-5]);
printk("\n");
}
- TLan_DioWrite8( dev->base_addr, TLAN_LED_REG, TLAN_LED_LINK );
+ tlan_dio_write8(dev->base_addr, TLAN_LED_REG,
+ TLAN_LED_LINK);
#ifdef MONITOR
/* We have link beat..for now anyway */
- priv->link = 1;
- /*Enabling link beat monitoring */
- TLan_SetTimer( dev, (10*HZ), TLAN_TIMER_LINK_BEAT );
+ priv->link = 1;
+ /*Enabling link beat monitoring */
+ tlan_set_timer(dev, (10*HZ), TLAN_TIMER_LINK_BEAT);
#endif
} else if (status & MII_GS_LINK) {
- printk( "TLAN: %s: Link active\n", dev->name );
- TLan_DioWrite8( dev->base_addr, TLAN_LED_REG, TLAN_LED_LINK );
+ pr_info("TLAN: %s: Link active\n", dev->name);
+ tlan_dio_write8(dev->base_addr, TLAN_LED_REG,
+ TLAN_LED_LINK);
}
}
- if ( priv->phyNum == 0 ) {
- TLan_MiiReadReg( dev, phy, TLAN_TLPHY_CTL, &tlphy_ctl );
- tlphy_ctl |= TLAN_TC_INTEN;
- TLan_MiiWriteReg( dev, phy, TLAN_TLPHY_CTL, tlphy_ctl );
- sio = TLan_DioRead8( dev->base_addr, TLAN_NET_SIO );
- sio |= TLAN_NET_SIO_MINTEN;
- TLan_DioWrite8( dev->base_addr, TLAN_NET_SIO, sio );
- }
-
- if ( status & MII_GS_LINK ) {
- TLan_SetMac( dev, 0, dev->dev_addr );
- priv->phyOnline = 1;
- outb( ( TLAN_HC_INT_ON >> 8 ), dev->base_addr + TLAN_HOST_CMD + 1 );
- if ( debug >= 1 && debug != TLAN_DEBUG_PROBE ) {
- outb( ( TLAN_HC_REQ_INT >> 8 ), dev->base_addr + TLAN_HOST_CMD + 1 );
- }
- outl( priv->rxListDMA, dev->base_addr + TLAN_CH_PARM );
- outl( TLAN_HC_GO | TLAN_HC_RT, dev->base_addr + TLAN_HOST_CMD );
+ if (priv->phy_num == 0) {
+ tlan_mii_read_reg(dev, phy, TLAN_TLPHY_CTL, &tlphy_ctl);
+ tlphy_ctl |= TLAN_TC_INTEN;
+ tlan_mii_write_reg(dev, phy, TLAN_TLPHY_CTL, tlphy_ctl);
+ sio = tlan_dio_read8(dev->base_addr, TLAN_NET_SIO);
+ sio |= TLAN_NET_SIO_MINTEN;
+ tlan_dio_write8(dev->base_addr, TLAN_NET_SIO, sio);
+ }
+
+ if (status & MII_GS_LINK) {
+ tlan_set_mac(dev, 0, dev->dev_addr);
+ priv->phy_online = 1;
+ outb((TLAN_HC_INT_ON >> 8), dev->base_addr + TLAN_HOST_CMD + 1);
+ if (debug >= 1 && debug != TLAN_DEBUG_PROBE)
+ outb((TLAN_HC_REQ_INT >> 8),
+ dev->base_addr + TLAN_HOST_CMD + 1);
+ outl(priv->rx_list_dma, dev->base_addr + TLAN_CH_PARM);
+ outl(TLAN_HC_GO | TLAN_HC_RT, dev->base_addr + TLAN_HOST_CMD);
netif_carrier_on(dev);
} else {
- printk( "TLAN: %s: Link inactive, will retry in 10 secs...\n",
- dev->name );
- TLan_SetTimer( dev, (10*HZ), TLAN_TIMER_FINISH_RESET );
+ pr_info("TLAN: %s: Link inactive, will retry in 10 secs...\n",
+ dev->name);
+ tlan_set_timer(dev, (10*HZ), TLAN_TIMER_FINISH_RESET);
return;
}
- TLan_SetMulticastList(dev);
+ tlan_set_multicast_list(dev);
-} /* TLan_FinishReset */
+}
- /***************************************************************
- * TLan_SetMac
- *
- * Returns:
- * Nothing
- * Parms:
- * dev Pointer to device structure of adapter
- * on which to change the AREG.
- * areg The AREG to set the address in (0 - 3).
- * mac A pointer to an array of chars. Each
- * element stores one byte of the address.
- * IE, it isn't in ascii.
- *
- * This function transfers a MAC address to one of the
- * TLAN AREGs (address registers). The TLAN chip locks
- * the register on writing to offset 0 and unlocks the
- * register after writing to offset 5. If NULL is passed
- * in mac, then the AREG is filled with 0's.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_set_mac
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * dev Pointer to device structure of adapter
+ * on which to change the AREG.
+ * areg The AREG to set the address in (0 - 3).
+ * mac A pointer to an array of chars. Each
+ * element stores one byte of the address.
+ * IE, it isn't in ascii.
+ *
+ * This function transfers a MAC address to one of the
+ * TLAN AREGs (address registers). The TLAN chip locks
+ * the register on writing to offset 0 and unlocks the
+ * register after writing to offset 5. If NULL is passed
+ * in mac, then the AREG is filled with 0's.
+ *
+ **************************************************************/
-static void TLan_SetMac( struct net_device *dev, int areg, char *mac )
+static void tlan_set_mac(struct net_device *dev, int areg, char *mac)
{
int i;
areg *= 6;
- if ( mac != NULL ) {
- for ( i = 0; i < 6; i++ )
- TLan_DioWrite8( dev->base_addr,
- TLAN_AREG_0 + areg + i, mac[i] );
+ if (mac != NULL) {
+ for (i = 0; i < 6; i++)
+ tlan_dio_write8(dev->base_addr,
+ TLAN_AREG_0 + areg + i, mac[i]);
} else {
- for ( i = 0; i < 6; i++ )
- TLan_DioWrite8( dev->base_addr,
- TLAN_AREG_0 + areg + i, 0 );
+ for (i = 0; i < 6; i++)
+ tlan_dio_write8(dev->base_addr,
+ TLAN_AREG_0 + areg + i, 0);
}
-} /* TLan_SetMac */
+}
/*****************************************************************************
******************************************************************************
- ThunderLAN Driver PHY Layer Routines
+ThunderLAN driver PHY layer routines
******************************************************************************
*****************************************************************************/
- /*********************************************************************
- * TLan_PhyPrint
- *
- * Returns:
- * Nothing
- * Parms:
- * dev A pointer to the device structure of the
- * TLAN device having the PHYs to be detailed.
- *
- * This function prints the registers a PHY (aka transceiver).
- *
- ********************************************************************/
+/*********************************************************************
+ * tlan_phy_print
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * dev A pointer to the device structure of the
+ * TLAN device having the PHYs to be detailed.
+ *
+ * This function prints the registers a PHY (aka transceiver).
+ *
+ ********************************************************************/
-static void TLan_PhyPrint( struct net_device *dev )
+static void tlan_phy_print(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u16 i, data0, data1, data2, data3, phy;
- phy = priv->phy[priv->phyNum];
-
- if ( priv->adapter->flags & TLAN_ADAPTER_UNMANAGED_PHY ) {
- printk( "TLAN: Device %s, Unmanaged PHY.\n", dev->name );
- } else if ( phy <= TLAN_PHY_MAX_ADDR ) {
- printk( "TLAN: Device %s, PHY 0x%02x.\n", dev->name, phy );
- printk( "TLAN: Off. +0 +1 +2 +3\n" );
- for ( i = 0; i < 0x20; i+= 4 ) {
- printk( "TLAN: 0x%02x", i );
- TLan_MiiReadReg( dev, phy, i, &data0 );
- printk( " 0x%04hx", data0 );
- TLan_MiiReadReg( dev, phy, i + 1, &data1 );
- printk( " 0x%04hx", data1 );
- TLan_MiiReadReg( dev, phy, i + 2, &data2 );
- printk( " 0x%04hx", data2 );
- TLan_MiiReadReg( dev, phy, i + 3, &data3 );
- printk( " 0x%04hx\n", data3 );
+ phy = priv->phy[priv->phy_num];
+
+ if (priv->adapter->flags & TLAN_ADAPTER_UNMANAGED_PHY) {
+ pr_info("TLAN: Device %s, Unmanaged PHY.\n", dev->name);
+ } else if (phy <= TLAN_PHY_MAX_ADDR) {
+ pr_info("TLAN: Device %s, PHY 0x%02x.\n", dev->name, phy);
+ pr_info("TLAN: Off. +0 +1 +2 +3\n");
+ for (i = 0; i < 0x20; i += 4) {
+ pr_info("TLAN: 0x%02x", i);
+ tlan_mii_read_reg(dev, phy, i, &data0);
+ printk(" 0x%04hx", data0);
+ tlan_mii_read_reg(dev, phy, i + 1, &data1);
+ printk(" 0x%04hx", data1);
+ tlan_mii_read_reg(dev, phy, i + 2, &data2);
+ printk(" 0x%04hx", data2);
+ tlan_mii_read_reg(dev, phy, i + 3, &data3);
+ printk(" 0x%04hx\n", data3);
}
} else {
- printk( "TLAN: Device %s, Invalid PHY.\n", dev->name );
+ pr_info("TLAN: Device %s, Invalid PHY.\n", dev->name);
}
-} /* TLan_PhyPrint */
+}
- /*********************************************************************
- * TLan_PhyDetect
- *
- * Returns:
- * Nothing
- * Parms:
- * dev A pointer to the device structure of the adapter
- * for which the PHY needs determined.
- *
- * So far I've found that adapters which have external PHYs
- * may also use the internal PHY for part of the functionality.
- * (eg, AUI/Thinnet). This function finds out if this TLAN
- * chip has an internal PHY, and then finds the first external
- * PHY (starting from address 0) if it exists).
- *
- ********************************************************************/
+/*********************************************************************
+ * tlan_phy_detect
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * dev A pointer to the device structure of the adapter
+ * for which the PHY needs determined.
+ *
+ * So far I've found that adapters which have external PHYs
+ * may also use the internal PHY for part of the functionality.
+ * (eg, AUI/Thinnet). This function finds out if this TLAN
+ * chip has an internal PHY, and then finds the first external
+ * PHY (starting from address 0) if it exists).
+ *
+ ********************************************************************/
-static void TLan_PhyDetect( struct net_device *dev )
+static void tlan_phy_detect(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u16 control;
u16 hi;
u16 lo;
u32 phy;
- if ( priv->adapter->flags & TLAN_ADAPTER_UNMANAGED_PHY ) {
- priv->phyNum = 0xFFFF;
+ if (priv->adapter->flags & TLAN_ADAPTER_UNMANAGED_PHY) {
+ priv->phy_num = 0xffff;
return;
}
- TLan_MiiReadReg( dev, TLAN_PHY_MAX_ADDR, MII_GEN_ID_HI, &hi );
+ tlan_mii_read_reg(dev, TLAN_PHY_MAX_ADDR, MII_GEN_ID_HI, &hi);
- if ( hi != 0xFFFF ) {
+ if (hi != 0xffff)
priv->phy[0] = TLAN_PHY_MAX_ADDR;
- } else {
+ else
priv->phy[0] = TLAN_PHY_NONE;
- }
priv->phy[1] = TLAN_PHY_NONE;
- for ( phy = 0; phy <= TLAN_PHY_MAX_ADDR; phy++ ) {
- TLan_MiiReadReg( dev, phy, MII_GEN_CTL, &control );
- TLan_MiiReadReg( dev, phy, MII_GEN_ID_HI, &hi );
- TLan_MiiReadReg( dev, phy, MII_GEN_ID_LO, &lo );
- if ( ( control != 0xFFFF ) ||
- ( hi != 0xFFFF ) || ( lo != 0xFFFF ) ) {
- TLAN_DBG( TLAN_DEBUG_GNRL,
- "PHY found at %02x %04x %04x %04x\n",
- phy, control, hi, lo );
- if ( ( priv->phy[1] == TLAN_PHY_NONE ) &&
- ( phy != TLAN_PHY_MAX_ADDR ) ) {
+ for (phy = 0; phy <= TLAN_PHY_MAX_ADDR; phy++) {
+ tlan_mii_read_reg(dev, phy, MII_GEN_CTL, &control);
+ tlan_mii_read_reg(dev, phy, MII_GEN_ID_HI, &hi);
+ tlan_mii_read_reg(dev, phy, MII_GEN_ID_LO, &lo);
+ if ((control != 0xffff) ||
+ (hi != 0xffff) || (lo != 0xffff)) {
+ TLAN_DBG(TLAN_DEBUG_GNRL,
+ "PHY found at %02x %04x %04x %04x\n",
+ phy, control, hi, lo);
+ if ((priv->phy[1] == TLAN_PHY_NONE) &&
+ (phy != TLAN_PHY_MAX_ADDR)) {
priv->phy[1] = phy;
}
}
}
- if ( priv->phy[1] != TLAN_PHY_NONE ) {
- priv->phyNum = 1;
- } else if ( priv->phy[0] != TLAN_PHY_NONE ) {
- priv->phyNum = 0;
- } else {
- printk( "TLAN: Cannot initialize device, no PHY was found!\n" );
- }
+ if (priv->phy[1] != TLAN_PHY_NONE)
+ priv->phy_num = 1;
+ else if (priv->phy[0] != TLAN_PHY_NONE)
+ priv->phy_num = 0;
+ else
+ pr_info("TLAN: Cannot initialize device, no PHY was found!\n");
-} /* TLan_PhyDetect */
+}
-static void TLan_PhyPowerDown( struct net_device *dev )
+static void tlan_phy_power_down(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u16 value;
- TLAN_DBG( TLAN_DEBUG_GNRL, "%s: Powering down PHY(s).\n", dev->name );
+ TLAN_DBG(TLAN_DEBUG_GNRL, "%s: Powering down PHY(s).\n", dev->name);
value = MII_GC_PDOWN | MII_GC_LOOPBK | MII_GC_ISOLATE;
- TLan_MiiSync( dev->base_addr );
- TLan_MiiWriteReg( dev, priv->phy[priv->phyNum], MII_GEN_CTL, value );
- if ( ( priv->phyNum == 0 ) &&
- ( priv->phy[1] != TLAN_PHY_NONE ) &&
- ( ! ( priv->adapter->flags & TLAN_ADAPTER_USE_INTERN_10 ) ) ) {
- TLan_MiiSync( dev->base_addr );
- TLan_MiiWriteReg( dev, priv->phy[1], MII_GEN_CTL, value );
+ tlan_mii_sync(dev->base_addr);
+ tlan_mii_write_reg(dev, priv->phy[priv->phy_num], MII_GEN_CTL, value);
+ if ((priv->phy_num == 0) &&
+ (priv->phy[1] != TLAN_PHY_NONE) &&
+ (!(priv->adapter->flags & TLAN_ADAPTER_USE_INTERN_10))) {
+ tlan_mii_sync(dev->base_addr);
+ tlan_mii_write_reg(dev, priv->phy[1], MII_GEN_CTL, value);
}
/* Wait for 50 ms and powerup
* This is abitrary. It is intended to make sure the
* transceiver settles.
*/
- TLan_SetTimer( dev, (HZ/20), TLAN_TIMER_PHY_PUP );
+ tlan_set_timer(dev, (HZ/20), TLAN_TIMER_PHY_PUP);
-} /* TLan_PhyPowerDown */
+}
-static void TLan_PhyPowerUp( struct net_device *dev )
+static void tlan_phy_power_up(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u16 value;
- TLAN_DBG( TLAN_DEBUG_GNRL, "%s: Powering up PHY.\n", dev->name );
- TLan_MiiSync( dev->base_addr );
+ TLAN_DBG(TLAN_DEBUG_GNRL, "%s: Powering up PHY.\n", dev->name);
+ tlan_mii_sync(dev->base_addr);
value = MII_GC_LOOPBK;
- TLan_MiiWriteReg( dev, priv->phy[priv->phyNum], MII_GEN_CTL, value );
- TLan_MiiSync(dev->base_addr);
+ tlan_mii_write_reg(dev, priv->phy[priv->phy_num], MII_GEN_CTL, value);
+ tlan_mii_sync(dev->base_addr);
/* Wait for 500 ms and reset the
* transceiver. The TLAN docs say both 50 ms and
* 500 ms, so do the longer, just in case.
*/
- TLan_SetTimer( dev, (HZ/20), TLAN_TIMER_PHY_RESET );
+ tlan_set_timer(dev, (HZ/20), TLAN_TIMER_PHY_RESET);
-} /* TLan_PhyPowerUp */
+}
-static void TLan_PhyReset( struct net_device *dev )
+static void tlan_phy_reset(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u16 phy;
u16 value;
- phy = priv->phy[priv->phyNum];
+ phy = priv->phy[priv->phy_num];
- TLAN_DBG( TLAN_DEBUG_GNRL, "%s: Reseting PHY.\n", dev->name );
- TLan_MiiSync( dev->base_addr );
+ TLAN_DBG(TLAN_DEBUG_GNRL, "%s: Reseting PHY.\n", dev->name);
+ tlan_mii_sync(dev->base_addr);
value = MII_GC_LOOPBK | MII_GC_RESET;
- TLan_MiiWriteReg( dev, phy, MII_GEN_CTL, value );
- TLan_MiiReadReg( dev, phy, MII_GEN_CTL, &value );
- while ( value & MII_GC_RESET ) {
- TLan_MiiReadReg( dev, phy, MII_GEN_CTL, &value );
- }
+ tlan_mii_write_reg(dev, phy, MII_GEN_CTL, value);
+ tlan_mii_read_reg(dev, phy, MII_GEN_CTL, &value);
+ while (value & MII_GC_RESET)
+ tlan_mii_read_reg(dev, phy, MII_GEN_CTL, &value);
/* Wait for 500 ms and initialize.
* I don't remember why I wait this long.
* I've changed this to 50ms, as it seems long enough.
*/
- TLan_SetTimer( dev, (HZ/20), TLAN_TIMER_PHY_START_LINK );
+ tlan_set_timer(dev, (HZ/20), TLAN_TIMER_PHY_START_LINK);
-} /* TLan_PhyReset */
+}
-static void TLan_PhyStartLink( struct net_device *dev )
+static void tlan_phy_start_link(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u16 ability;
u16 control;
u16 data;
u16 status;
u16 tctl;
- phy = priv->phy[priv->phyNum];
- TLAN_DBG( TLAN_DEBUG_GNRL, "%s: Trying to activate link.\n", dev->name );
- TLan_MiiReadReg( dev, phy, MII_GEN_STS, &status );
- TLan_MiiReadReg( dev, phy, MII_GEN_STS, &ability );
+ phy = priv->phy[priv->phy_num];
+ TLAN_DBG(TLAN_DEBUG_GNRL, "%s: Trying to activate link.\n", dev->name);
+ tlan_mii_read_reg(dev, phy, MII_GEN_STS, &status);
+ tlan_mii_read_reg(dev, phy, MII_GEN_STS, &ability);
- if ( ( status & MII_GS_AUTONEG ) &&
- ( ! priv->aui ) ) {
+ if ((status & MII_GS_AUTONEG) &&
+ (!priv->aui)) {
ability = status >> 11;
- if ( priv->speed == TLAN_SPEED_10 &&
- priv->duplex == TLAN_DUPLEX_HALF) {
- TLan_MiiWriteReg( dev, phy, MII_GEN_CTL, 0x0000);
- } else if ( priv->speed == TLAN_SPEED_10 &&
- priv->duplex == TLAN_DUPLEX_FULL) {
- priv->tlanFullDuplex = true;
- TLan_MiiWriteReg( dev, phy, MII_GEN_CTL, 0x0100);
- } else if ( priv->speed == TLAN_SPEED_100 &&
- priv->duplex == TLAN_DUPLEX_HALF) {
- TLan_MiiWriteReg( dev, phy, MII_GEN_CTL, 0x2000);
- } else if ( priv->speed == TLAN_SPEED_100 &&
- priv->duplex == TLAN_DUPLEX_FULL) {
- priv->tlanFullDuplex = true;
- TLan_MiiWriteReg( dev, phy, MII_GEN_CTL, 0x2100);
+ if (priv->speed == TLAN_SPEED_10 &&
+ priv->duplex == TLAN_DUPLEX_HALF) {
+ tlan_mii_write_reg(dev, phy, MII_GEN_CTL, 0x0000);
+ } else if (priv->speed == TLAN_SPEED_10 &&
+ priv->duplex == TLAN_DUPLEX_FULL) {
+ priv->tlan_full_duplex = true;
+ tlan_mii_write_reg(dev, phy, MII_GEN_CTL, 0x0100);
+ } else if (priv->speed == TLAN_SPEED_100 &&
+ priv->duplex == TLAN_DUPLEX_HALF) {
+ tlan_mii_write_reg(dev, phy, MII_GEN_CTL, 0x2000);
+ } else if (priv->speed == TLAN_SPEED_100 &&
+ priv->duplex == TLAN_DUPLEX_FULL) {
+ priv->tlan_full_duplex = true;
+ tlan_mii_write_reg(dev, phy, MII_GEN_CTL, 0x2100);
} else {
/* Set Auto-Neg advertisement */
- TLan_MiiWriteReg( dev, phy, MII_AN_ADV, (ability << 5) | 1);
+ tlan_mii_write_reg(dev, phy, MII_AN_ADV,
+ (ability << 5) | 1);
/* Enablee Auto-Neg */
- TLan_MiiWriteReg( dev, phy, MII_GEN_CTL, 0x1000 );
+ tlan_mii_write_reg(dev, phy, MII_GEN_CTL, 0x1000);
/* Restart Auto-Neg */
- TLan_MiiWriteReg( dev, phy, MII_GEN_CTL, 0x1200 );
+ tlan_mii_write_reg(dev, phy, MII_GEN_CTL, 0x1200);
/* Wait for 4 sec for autonegotiation
- * to complete. The max spec time is less than this
- * but the card need additional time to start AN.
- * .5 sec should be plenty extra.
- */
- printk( "TLAN: %s: Starting autonegotiation.\n", dev->name );
- TLan_SetTimer( dev, (2*HZ), TLAN_TIMER_PHY_FINISH_AN );
+ * to complete. The max spec time is less than this
+ * but the card need additional time to start AN.
+ * .5 sec should be plenty extra.
+ */
+ pr_info("TLAN: %s: Starting autonegotiation.\n",
+ dev->name);
+ tlan_set_timer(dev, (2*HZ), TLAN_TIMER_PHY_FINISH_AN);
return;
}
}
- if ( ( priv->aui ) && ( priv->phyNum != 0 ) ) {
- priv->phyNum = 0;
- data = TLAN_NET_CFG_1FRAG | TLAN_NET_CFG_1CHAN | TLAN_NET_CFG_PHY_EN;
- TLan_DioWrite16( dev->base_addr, TLAN_NET_CONFIG, data );
- TLan_SetTimer( dev, (40*HZ/1000), TLAN_TIMER_PHY_PDOWN );
+ if ((priv->aui) && (priv->phy_num != 0)) {
+ priv->phy_num = 0;
+ data = TLAN_NET_CFG_1FRAG | TLAN_NET_CFG_1CHAN
+ | TLAN_NET_CFG_PHY_EN;
+ tlan_dio_write16(dev->base_addr, TLAN_NET_CONFIG, data);
+ tlan_set_timer(dev, (40*HZ/1000), TLAN_TIMER_PHY_PDOWN);
return;
- } else if ( priv->phyNum == 0 ) {
+ } else if (priv->phy_num == 0) {
control = 0;
- TLan_MiiReadReg( dev, phy, TLAN_TLPHY_CTL, &tctl );
- if ( priv->aui ) {
- tctl |= TLAN_TC_AUISEL;
+ tlan_mii_read_reg(dev, phy, TLAN_TLPHY_CTL, &tctl);
+ if (priv->aui) {
+ tctl |= TLAN_TC_AUISEL;
} else {
- tctl &= ~TLAN_TC_AUISEL;
- if ( priv->duplex == TLAN_DUPLEX_FULL ) {
+ tctl &= ~TLAN_TC_AUISEL;
+ if (priv->duplex == TLAN_DUPLEX_FULL) {
control |= MII_GC_DUPLEX;
- priv->tlanFullDuplex = true;
+ priv->tlan_full_duplex = true;
}
- if ( priv->speed == TLAN_SPEED_100 ) {
+ if (priv->speed == TLAN_SPEED_100)
control |= MII_GC_SPEEDSEL;
- }
}
- TLan_MiiWriteReg( dev, phy, MII_GEN_CTL, control );
- TLan_MiiWriteReg( dev, phy, TLAN_TLPHY_CTL, tctl );
+ tlan_mii_write_reg(dev, phy, MII_GEN_CTL, control);
+ tlan_mii_write_reg(dev, phy, TLAN_TLPHY_CTL, tctl);
}
/* Wait for 2 sec to give the transceiver time
* to establish link.
*/
- TLan_SetTimer( dev, (4*HZ), TLAN_TIMER_FINISH_RESET );
+ tlan_set_timer(dev, (4*HZ), TLAN_TIMER_FINISH_RESET);
-} /* TLan_PhyStartLink */
+}
-static void TLan_PhyFinishAutoNeg( struct net_device *dev )
+static void tlan_phy_finish_auto_neg(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u16 an_adv;
u16 an_lpa;
u16 data;
u16 phy;
u16 status;
- phy = priv->phy[priv->phyNum];
+ phy = priv->phy[priv->phy_num];
- TLan_MiiReadReg( dev, phy, MII_GEN_STS, &status );
- udelay( 1000 );
- TLan_MiiReadReg( dev, phy, MII_GEN_STS, &status );
+ tlan_mii_read_reg(dev, phy, MII_GEN_STS, &status);
+ udelay(1000);
+ tlan_mii_read_reg(dev, phy, MII_GEN_STS, &status);
- if ( ! ( status & MII_GS_AUTOCMPLT ) ) {
+ if (!(status & MII_GS_AUTOCMPLT)) {
/* Wait for 8 sec to give the process
* more time. Perhaps we should fail after a while.
*/
- if (!priv->neg_be_verbose++) {
- pr_info("TLAN: Giving autonegotiation more time.\n");
- pr_info("TLAN: Please check that your adapter has\n");
- pr_info("TLAN: been properly connected to a HUB or Switch.\n");
- pr_info("TLAN: Trying to establish link in the background...\n");
- }
- TLan_SetTimer( dev, (8*HZ), TLAN_TIMER_PHY_FINISH_AN );
+ if (!priv->neg_be_verbose++) {
+ pr_info("TLAN: Giving autonegotiation more time.\n");
+ pr_info("TLAN: Please check that your adapter has\n");
+ pr_info("TLAN: been properly connected to a HUB or Switch.\n");
+ pr_info("TLAN: Trying to establish link in the background...\n");
+ }
+ tlan_set_timer(dev, (8*HZ), TLAN_TIMER_PHY_FINISH_AN);
return;
}
- printk( "TLAN: %s: Autonegotiation complete.\n", dev->name );
- TLan_MiiReadReg( dev, phy, MII_AN_ADV, &an_adv );
- TLan_MiiReadReg( dev, phy, MII_AN_LPA, &an_lpa );
+ pr_info("TLAN: %s: Autonegotiation complete.\n", dev->name);
+ tlan_mii_read_reg(dev, phy, MII_AN_ADV, &an_adv);
+ tlan_mii_read_reg(dev, phy, MII_AN_LPA, &an_lpa);
mode = an_adv & an_lpa & 0x03E0;
- if ( mode & 0x0100 ) {
- priv->tlanFullDuplex = true;
- } else if ( ! ( mode & 0x0080 ) && ( mode & 0x0040 ) ) {
- priv->tlanFullDuplex = true;
- }
-
- if ( ( ! ( mode & 0x0180 ) ) &&
- ( priv->adapter->flags & TLAN_ADAPTER_USE_INTERN_10 ) &&
- ( priv->phyNum != 0 ) ) {
- priv->phyNum = 0;
- data = TLAN_NET_CFG_1FRAG | TLAN_NET_CFG_1CHAN | TLAN_NET_CFG_PHY_EN;
- TLan_DioWrite16( dev->base_addr, TLAN_NET_CONFIG, data );
- TLan_SetTimer( dev, (400*HZ/1000), TLAN_TIMER_PHY_PDOWN );
+ if (mode & 0x0100)
+ priv->tlan_full_duplex = true;
+ else if (!(mode & 0x0080) && (mode & 0x0040))
+ priv->tlan_full_duplex = true;
+
+ if ((!(mode & 0x0180)) &&
+ (priv->adapter->flags & TLAN_ADAPTER_USE_INTERN_10) &&
+ (priv->phy_num != 0)) {
+ priv->phy_num = 0;
+ data = TLAN_NET_CFG_1FRAG | TLAN_NET_CFG_1CHAN
+ | TLAN_NET_CFG_PHY_EN;
+ tlan_dio_write16(dev->base_addr, TLAN_NET_CONFIG, data);
+ tlan_set_timer(dev, (400*HZ/1000), TLAN_TIMER_PHY_PDOWN);
return;
}
- if ( priv->phyNum == 0 ) {
- if ( ( priv->duplex == TLAN_DUPLEX_FULL ) ||
- ( an_adv & an_lpa & 0x0040 ) ) {
- TLan_MiiWriteReg( dev, phy, MII_GEN_CTL,
- MII_GC_AUTOENB | MII_GC_DUPLEX );
- pr_info("TLAN: Starting internal PHY with FULL-DUPLEX\n" );
+ if (priv->phy_num == 0) {
+ if ((priv->duplex == TLAN_DUPLEX_FULL) ||
+ (an_adv & an_lpa & 0x0040)) {
+ tlan_mii_write_reg(dev, phy, MII_GEN_CTL,
+ MII_GC_AUTOENB | MII_GC_DUPLEX);
+ pr_info("TLAN: Starting internal PHY with FULL-DUPLEX\n");
} else {
- TLan_MiiWriteReg( dev, phy, MII_GEN_CTL, MII_GC_AUTOENB );
- pr_info( "TLAN: Starting internal PHY with HALF-DUPLEX\n" );
+ tlan_mii_write_reg(dev, phy, MII_GEN_CTL,
+ MII_GC_AUTOENB);
+ pr_info("TLAN: Starting internal PHY with HALF-DUPLEX\n");
}
}
/* Wait for 100 ms. No reason in partiticular.
*/
- TLan_SetTimer( dev, (HZ/10), TLAN_TIMER_FINISH_RESET );
+ tlan_set_timer(dev, (HZ/10), TLAN_TIMER_FINISH_RESET);
-} /* TLan_PhyFinishAutoNeg */
+}
#ifdef MONITOR
- /*********************************************************************
- *
- * TLan_phyMonitor
- *
- * Returns:
- * None
- *
- * Params:
- * dev The device structure of this device.
- *
- *
- * This function monitors PHY condition by reading the status
- * register via the MII bus. This can be used to give info
- * about link changes (up/down), and possible switch to alternate
- * media.
- *
- * ******************************************************************/
-
-void TLan_PhyMonitor( struct net_device *dev )
+/*********************************************************************
+ *
+ * tlan_phy_monitor
+ *
+ * Returns:
+ * None
+ *
+ * Params:
+ * dev The device structure of this device.
+ *
+ *
+ * This function monitors PHY condition by reading the status
+ * register via the MII bus. This can be used to give info
+ * about link changes (up/down), and possible switch to alternate
+ * media.
+ *
+ *******************************************************************/
+
+void tlan_phy_monitor(struct net_device *dev)
{
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
u16 phy;
u16 phy_status;
- phy = priv->phy[priv->phyNum];
+ phy = priv->phy[priv->phy_num];
- /* Get PHY status register */
- TLan_MiiReadReg( dev, phy, MII_GEN_STS, &phy_status );
+ /* Get PHY status register */
+ tlan_mii_read_reg(dev, phy, MII_GEN_STS, &phy_status);
- /* Check if link has been lost */
- if (!(phy_status & MII_GS_LINK)) {
- if (priv->link) {
- priv->link = 0;
- printk(KERN_DEBUG "TLAN: %s has lost link\n", dev->name);
- netif_carrier_off(dev);
- TLan_SetTimer( dev, (2*HZ), TLAN_TIMER_LINK_BEAT );
- return;
+ /* Check if link has been lost */
+ if (!(phy_status & MII_GS_LINK)) {
+ if (priv->link) {
+ priv->link = 0;
+ printk(KERN_DEBUG "TLAN: %s has lost link\n",
+ dev->name);
+ netif_carrier_off(dev);
+ tlan_set_timer(dev, (2*HZ), TLAN_TIMER_LINK_BEAT);
+ return;
}
}
- /* Link restablished? */
- if ((phy_status & MII_GS_LINK) && !priv->link) {
- priv->link = 1;
- printk(KERN_DEBUG "TLAN: %s has reestablished link\n", dev->name);
+ /* Link restablished? */
+ if ((phy_status & MII_GS_LINK) && !priv->link) {
+ priv->link = 1;
+ printk(KERN_DEBUG "TLAN: %s has reestablished link\n",
+ dev->name);
netif_carrier_on(dev);
- }
+ }
/* Setup a new monitor */
- TLan_SetTimer( dev, (2*HZ), TLAN_TIMER_LINK_BEAT );
+ tlan_set_timer(dev, (2*HZ), TLAN_TIMER_LINK_BEAT);
}
#endif /* MONITOR */
/*****************************************************************************
******************************************************************************
- ThunderLAN Driver MII Routines
+ThunderLAN driver MII routines
- These routines are based on the information in Chap. 2 of the
- "ThunderLAN Programmer's Guide", pp. 15-24.
+these routines are based on the information in chap. 2 of the
+"ThunderLAN Programmer's Guide", pp. 15-24.
******************************************************************************
*****************************************************************************/
- /***************************************************************
- * TLan_MiiReadReg
- *
- * Returns:
- * false if ack received ok
- * true if no ack received or other error
- *
- * Parms:
- * dev The device structure containing
- * The io address and interrupt count
- * for this device.
- * phy The address of the PHY to be queried.
- * reg The register whose contents are to be
- * retrieved.
- * val A pointer to a variable to store the
- * retrieved value.
- *
- * This function uses the TLAN's MII bus to retrieve the contents
- * of a given register on a PHY. It sends the appropriate info
- * and then reads the 16-bit register value from the MII bus via
- * the TLAN SIO register.
- *
- **************************************************************/
-
-static bool TLan_MiiReadReg( struct net_device *dev, u16 phy, u16 reg, u16 *val )
+/***************************************************************
+ * tlan_mii_read_reg
+ *
+ * Returns:
+ * false if ack received ok
+ * true if no ack received or other error
+ *
+ * Parms:
+ * dev The device structure containing
+ * The io address and interrupt count
+ * for this device.
+ * phy The address of the PHY to be queried.
+ * reg The register whose contents are to be
+ * retrieved.
+ * val A pointer to a variable to store the
+ * retrieved value.
+ *
+ * This function uses the TLAN's MII bus to retrieve the contents
+ * of a given register on a PHY. It sends the appropriate info
+ * and then reads the 16-bit register value from the MII bus via
+ * the TLAN SIO register.
+ *
+ **************************************************************/
+
+static bool
+tlan_mii_read_reg(struct net_device *dev, u16 phy, u16 reg, u16 *val)
{
u8 nack;
u16 sio, tmp;
- u32 i;
+ u32 i;
bool err;
int minten;
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
unsigned long flags = 0;
err = false;
if (!in_irq())
spin_lock_irqsave(&priv->lock, flags);
- TLan_MiiSync(dev->base_addr);
+ tlan_mii_sync(dev->base_addr);
- minten = TLan_GetBit( TLAN_NET_SIO_MINTEN, sio );
- if ( minten )
- TLan_ClearBit(TLAN_NET_SIO_MINTEN, sio);
+ minten = tlan_get_bit(TLAN_NET_SIO_MINTEN, sio);
+ if (minten)
+ tlan_clear_bit(TLAN_NET_SIO_MINTEN, sio);
- TLan_MiiSendData( dev->base_addr, 0x1, 2 ); /* Start ( 01b ) */
- TLan_MiiSendData( dev->base_addr, 0x2, 2 ); /* Read ( 10b ) */
- TLan_MiiSendData( dev->base_addr, phy, 5 ); /* Device # */
- TLan_MiiSendData( dev->base_addr, reg, 5 ); /* Register # */
+ tlan_mii_send_data(dev->base_addr, 0x1, 2); /* start (01b) */
+ tlan_mii_send_data(dev->base_addr, 0x2, 2); /* read (10b) */
+ tlan_mii_send_data(dev->base_addr, phy, 5); /* device # */
+ tlan_mii_send_data(dev->base_addr, reg, 5); /* register # */
- TLan_ClearBit(TLAN_NET_SIO_MTXEN, sio); /* Change direction */
+ tlan_clear_bit(TLAN_NET_SIO_MTXEN, sio); /* change direction */
- TLan_ClearBit(TLAN_NET_SIO_MCLK, sio); /* Clock Idle bit */
- TLan_SetBit(TLAN_NET_SIO_MCLK, sio);
- TLan_ClearBit(TLAN_NET_SIO_MCLK, sio); /* Wait 300ns */
+ tlan_clear_bit(TLAN_NET_SIO_MCLK, sio); /* clock idle bit */
+ tlan_set_bit(TLAN_NET_SIO_MCLK, sio);
+ tlan_clear_bit(TLAN_NET_SIO_MCLK, sio); /* wait 300ns */
- nack = TLan_GetBit(TLAN_NET_SIO_MDATA, sio); /* Check for ACK */
- TLan_SetBit(TLAN_NET_SIO_MCLK, sio); /* Finish ACK */
- if (nack) { /* No ACK, so fake it */
+ nack = tlan_get_bit(TLAN_NET_SIO_MDATA, sio); /* check for ACK */
+ tlan_set_bit(TLAN_NET_SIO_MCLK, sio); /* finish ACK */
+ if (nack) { /* no ACK, so fake it */
for (i = 0; i < 16; i++) {
- TLan_ClearBit(TLAN_NET_SIO_MCLK, sio);
- TLan_SetBit(TLAN_NET_SIO_MCLK, sio);
+ tlan_clear_bit(TLAN_NET_SIO_MCLK, sio);
+ tlan_set_bit(TLAN_NET_SIO_MCLK, sio);
}
tmp = 0xffff;
err = true;
} else { /* ACK, so read data */
for (tmp = 0, i = 0x8000; i; i >>= 1) {
- TLan_ClearBit(TLAN_NET_SIO_MCLK, sio);
- if (TLan_GetBit(TLAN_NET_SIO_MDATA, sio))
+ tlan_clear_bit(TLAN_NET_SIO_MCLK, sio);
+ if (tlan_get_bit(TLAN_NET_SIO_MDATA, sio))
tmp |= i;
- TLan_SetBit(TLAN_NET_SIO_MCLK, sio);
+ tlan_set_bit(TLAN_NET_SIO_MCLK, sio);
}
}
- TLan_ClearBit(TLAN_NET_SIO_MCLK, sio); /* Idle cycle */
- TLan_SetBit(TLAN_NET_SIO_MCLK, sio);
+ tlan_clear_bit(TLAN_NET_SIO_MCLK, sio); /* idle cycle */
+ tlan_set_bit(TLAN_NET_SIO_MCLK, sio);
- if ( minten )
- TLan_SetBit(TLAN_NET_SIO_MINTEN, sio);
+ if (minten)
+ tlan_set_bit(TLAN_NET_SIO_MINTEN, sio);
*val = tmp;
return err;
-} /* TLan_MiiReadReg */
+}
- /***************************************************************
- * TLan_MiiSendData
- *
- * Returns:
- * Nothing
- * Parms:
- * base_port The base IO port of the adapter in
- * question.
- * dev The address of the PHY to be queried.
- * data The value to be placed on the MII bus.
- * num_bits The number of bits in data that are to
- * be placed on the MII bus.
- *
- * This function sends on sequence of bits on the MII
- * configuration bus.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_mii_send_data
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * base_port The base IO port of the adapter in
+ * question.
+ * dev The address of the PHY to be queried.
+ * data The value to be placed on the MII bus.
+ * num_bits The number of bits in data that are to
+ * be placed on the MII bus.
+ *
+ * This function sends on sequence of bits on the MII
+ * configuration bus.
+ *
+ **************************************************************/
-static void TLan_MiiSendData( u16 base_port, u32 data, unsigned num_bits )
+static void tlan_mii_send_data(u16 base_port, u32 data, unsigned num_bits)
{
u16 sio;
u32 i;
- if ( num_bits == 0 )
+ if (num_bits == 0)
return;
- outw( TLAN_NET_SIO, base_port + TLAN_DIO_ADR );
+ outw(TLAN_NET_SIO, base_port + TLAN_DIO_ADR);
sio = base_port + TLAN_DIO_DATA + TLAN_NET_SIO;
- TLan_SetBit( TLAN_NET_SIO_MTXEN, sio );
+ tlan_set_bit(TLAN_NET_SIO_MTXEN, sio);
- for ( i = ( 0x1 << ( num_bits - 1 ) ); i; i >>= 1 ) {
- TLan_ClearBit( TLAN_NET_SIO_MCLK, sio );
- (void) TLan_GetBit( TLAN_NET_SIO_MCLK, sio );
- if ( data & i )
- TLan_SetBit( TLAN_NET_SIO_MDATA, sio );
+ for (i = (0x1 << (num_bits - 1)); i; i >>= 1) {
+ tlan_clear_bit(TLAN_NET_SIO_MCLK, sio);
+ (void) tlan_get_bit(TLAN_NET_SIO_MCLK, sio);
+ if (data & i)
+ tlan_set_bit(TLAN_NET_SIO_MDATA, sio);
else
- TLan_ClearBit( TLAN_NET_SIO_MDATA, sio );
- TLan_SetBit( TLAN_NET_SIO_MCLK, sio );
- (void) TLan_GetBit( TLAN_NET_SIO_MCLK, sio );
+ tlan_clear_bit(TLAN_NET_SIO_MDATA, sio);
+ tlan_set_bit(TLAN_NET_SIO_MCLK, sio);
+ (void) tlan_get_bit(TLAN_NET_SIO_MCLK, sio);
}
-} /* TLan_MiiSendData */
+}
- /***************************************************************
- * TLan_MiiSync
- *
- * Returns:
- * Nothing
- * Parms:
- * base_port The base IO port of the adapter in
- * question.
- *
- * This functions syncs all PHYs in terms of the MII configuration
- * bus.
- *
- **************************************************************/
+/***************************************************************
+ * TLan_MiiSync
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * base_port The base IO port of the adapter in
+ * question.
+ *
+ * This functions syncs all PHYs in terms of the MII configuration
+ * bus.
+ *
+ **************************************************************/
-static void TLan_MiiSync( u16 base_port )
+static void tlan_mii_sync(u16 base_port)
{
int i;
u16 sio;
- outw( TLAN_NET_SIO, base_port + TLAN_DIO_ADR );
+ outw(TLAN_NET_SIO, base_port + TLAN_DIO_ADR);
sio = base_port + TLAN_DIO_DATA + TLAN_NET_SIO;
- TLan_ClearBit( TLAN_NET_SIO_MTXEN, sio );
- for ( i = 0; i < 32; i++ ) {
- TLan_ClearBit( TLAN_NET_SIO_MCLK, sio );
- TLan_SetBit( TLAN_NET_SIO_MCLK, sio );
+ tlan_clear_bit(TLAN_NET_SIO_MTXEN, sio);
+ for (i = 0; i < 32; i++) {
+ tlan_clear_bit(TLAN_NET_SIO_MCLK, sio);
+ tlan_set_bit(TLAN_NET_SIO_MCLK, sio);
}
-} /* TLan_MiiSync */
+}
- /***************************************************************
- * TLan_MiiWriteReg
- *
- * Returns:
- * Nothing
- * Parms:
- * dev The device structure for the device
- * to write to.
- * phy The address of the PHY to be written to.
- * reg The register whose contents are to be
- * written.
- * val The value to be written to the register.
- *
- * This function uses the TLAN's MII bus to write the contents of a
- * given register on a PHY. It sends the appropriate info and then
- * writes the 16-bit register value from the MII configuration bus
- * via the TLAN SIO register.
- *
- **************************************************************/
+/***************************************************************
+ * tlan_mii_write_reg
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * dev The device structure for the device
+ * to write to.
+ * phy The address of the PHY to be written to.
+ * reg The register whose contents are to be
+ * written.
+ * val The value to be written to the register.
+ *
+ * This function uses the TLAN's MII bus to write the contents of a
+ * given register on a PHY. It sends the appropriate info and then
+ * writes the 16-bit register value from the MII configuration bus
+ * via the TLAN SIO register.
+ *
+ **************************************************************/
-static void TLan_MiiWriteReg( struct net_device *dev, u16 phy, u16 reg, u16 val )
+static void
+tlan_mii_write_reg(struct net_device *dev, u16 phy, u16 reg, u16 val)
{
u16 sio;
int minten;
unsigned long flags = 0;
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
outw(TLAN_NET_SIO, dev->base_addr + TLAN_DIO_ADR);
sio = dev->base_addr + TLAN_DIO_DATA + TLAN_NET_SIO;
if (!in_irq())
spin_lock_irqsave(&priv->lock, flags);
- TLan_MiiSync( dev->base_addr );
+ tlan_mii_sync(dev->base_addr);
- minten = TLan_GetBit( TLAN_NET_SIO_MINTEN, sio );
- if ( minten )
- TLan_ClearBit( TLAN_NET_SIO_MINTEN, sio );
+ minten = tlan_get_bit(TLAN_NET_SIO_MINTEN, sio);
+ if (minten)
+ tlan_clear_bit(TLAN_NET_SIO_MINTEN, sio);
- TLan_MiiSendData( dev->base_addr, 0x1, 2 ); /* Start ( 01b ) */
- TLan_MiiSendData( dev->base_addr, 0x1, 2 ); /* Write ( 01b ) */
- TLan_MiiSendData( dev->base_addr, phy, 5 ); /* Device # */
- TLan_MiiSendData( dev->base_addr, reg, 5 ); /* Register # */
+ tlan_mii_send_data(dev->base_addr, 0x1, 2); /* start (01b) */
+ tlan_mii_send_data(dev->base_addr, 0x1, 2); /* write (01b) */
+ tlan_mii_send_data(dev->base_addr, phy, 5); /* device # */
+ tlan_mii_send_data(dev->base_addr, reg, 5); /* register # */
- TLan_MiiSendData( dev->base_addr, 0x2, 2 ); /* Send ACK */
- TLan_MiiSendData( dev->base_addr, val, 16 ); /* Send Data */
+ tlan_mii_send_data(dev->base_addr, 0x2, 2); /* send ACK */
+ tlan_mii_send_data(dev->base_addr, val, 16); /* send data */
- TLan_ClearBit( TLAN_NET_SIO_MCLK, sio ); /* Idle cycle */
- TLan_SetBit( TLAN_NET_SIO_MCLK, sio );
+ tlan_clear_bit(TLAN_NET_SIO_MCLK, sio); /* idle cycle */
+ tlan_set_bit(TLAN_NET_SIO_MCLK, sio);
- if ( minten )
- TLan_SetBit( TLAN_NET_SIO_MINTEN, sio );
+ if (minten)
+ tlan_set_bit(TLAN_NET_SIO_MINTEN, sio);
if (!in_irq())
spin_unlock_irqrestore(&priv->lock, flags);
-} /* TLan_MiiWriteReg */
+}
/*****************************************************************************
******************************************************************************
- ThunderLAN Driver Eeprom routines
+ThunderLAN driver eeprom routines
- The Compaq Netelligent 10 and 10/100 cards use a Microchip 24C02A
- EEPROM. These functions are based on information in Microchip's
- data sheet. I don't know how well this functions will work with
- other EEPROMs.
+the Compaq netelligent 10 and 10/100 cards use a microchip 24C02A
+EEPROM. these functions are based on information in microchip's
+data sheet. I don't know how well this functions will work with
+other Eeproms.
******************************************************************************
*****************************************************************************/
- /***************************************************************
- * TLan_EeSendStart
- *
- * Returns:
- * Nothing
- * Parms:
- * io_base The IO port base address for the
- * TLAN device with the EEPROM to
- * use.
- *
- * This function sends a start cycle to an EEPROM attached
- * to a TLAN chip.
- *
- **************************************************************/
-
-static void TLan_EeSendStart( u16 io_base )
+/***************************************************************
+ * tlan_ee_send_start
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * io_base The IO port base address for the
+ * TLAN device with the EEPROM to
+ * use.
+ *
+ * This function sends a start cycle to an EEPROM attached
+ * to a TLAN chip.
+ *
+ **************************************************************/
+
+static void tlan_ee_send_start(u16 io_base)
{
u16 sio;
- outw( TLAN_NET_SIO, io_base + TLAN_DIO_ADR );
+ outw(TLAN_NET_SIO, io_base + TLAN_DIO_ADR);
sio = io_base + TLAN_DIO_DATA + TLAN_NET_SIO;
- TLan_SetBit( TLAN_NET_SIO_ECLOK, sio );
- TLan_SetBit( TLAN_NET_SIO_EDATA, sio );
- TLan_SetBit( TLAN_NET_SIO_ETXEN, sio );
- TLan_ClearBit( TLAN_NET_SIO_EDATA, sio );
- TLan_ClearBit( TLAN_NET_SIO_ECLOK, sio );
-
-} /* TLan_EeSendStart */
-
-
-
-
- /***************************************************************
- * TLan_EeSendByte
- *
- * Returns:
- * If the correct ack was received, 0, otherwise 1
- * Parms: io_base The IO port base address for the
- * TLAN device with the EEPROM to
- * use.
- * data The 8 bits of information to
- * send to the EEPROM.
- * stop If TLAN_EEPROM_STOP is passed, a
- * stop cycle is sent after the
- * byte is sent after the ack is
- * read.
- *
- * This function sends a byte on the serial EEPROM line,
- * driving the clock to send each bit. The function then
- * reverses transmission direction and reads an acknowledge
- * bit.
- *
- **************************************************************/
-
-static int TLan_EeSendByte( u16 io_base, u8 data, int stop )
+ tlan_set_bit(TLAN_NET_SIO_ECLOK, sio);
+ tlan_set_bit(TLAN_NET_SIO_EDATA, sio);
+ tlan_set_bit(TLAN_NET_SIO_ETXEN, sio);
+ tlan_clear_bit(TLAN_NET_SIO_EDATA, sio);
+ tlan_clear_bit(TLAN_NET_SIO_ECLOK, sio);
+
+}
+
+
+
+
+/***************************************************************
+ * tlan_ee_send_byte
+ *
+ * Returns:
+ * If the correct ack was received, 0, otherwise 1
+ * Parms: io_base The IO port base address for the
+ * TLAN device with the EEPROM to
+ * use.
+ * data The 8 bits of information to
+ * send to the EEPROM.
+ * stop If TLAN_EEPROM_STOP is passed, a
+ * stop cycle is sent after the
+ * byte is sent after the ack is
+ * read.
+ *
+ * This function sends a byte on the serial EEPROM line,
+ * driving the clock to send each bit. The function then
+ * reverses transmission direction and reads an acknowledge
+ * bit.
+ *
+ **************************************************************/
+
+static int tlan_ee_send_byte(u16 io_base, u8 data, int stop)
{
int err;
u8 place;
u16 sio;
- outw( TLAN_NET_SIO, io_base + TLAN_DIO_ADR );
+ outw(TLAN_NET_SIO, io_base + TLAN_DIO_ADR);
sio = io_base + TLAN_DIO_DATA + TLAN_NET_SIO;
/* Assume clock is low, tx is enabled; */
- for ( place = 0x80; place != 0; place >>= 1 ) {
- if ( place & data )
- TLan_SetBit( TLAN_NET_SIO_EDATA, sio );
+ for (place = 0x80; place != 0; place >>= 1) {
+ if (place & data)
+ tlan_set_bit(TLAN_NET_SIO_EDATA, sio);
else
- TLan_ClearBit( TLAN_NET_SIO_EDATA, sio );
- TLan_SetBit( TLAN_NET_SIO_ECLOK, sio );
- TLan_ClearBit( TLAN_NET_SIO_ECLOK, sio );
+ tlan_clear_bit(TLAN_NET_SIO_EDATA, sio);
+ tlan_set_bit(TLAN_NET_SIO_ECLOK, sio);
+ tlan_clear_bit(TLAN_NET_SIO_ECLOK, sio);
}
- TLan_ClearBit( TLAN_NET_SIO_ETXEN, sio );
- TLan_SetBit( TLAN_NET_SIO_ECLOK, sio );
- err = TLan_GetBit( TLAN_NET_SIO_EDATA, sio );
- TLan_ClearBit( TLAN_NET_SIO_ECLOK, sio );
- TLan_SetBit( TLAN_NET_SIO_ETXEN, sio );
+ tlan_clear_bit(TLAN_NET_SIO_ETXEN, sio);
+ tlan_set_bit(TLAN_NET_SIO_ECLOK, sio);
+ err = tlan_get_bit(TLAN_NET_SIO_EDATA, sio);
+ tlan_clear_bit(TLAN_NET_SIO_ECLOK, sio);
+ tlan_set_bit(TLAN_NET_SIO_ETXEN, sio);
- if ( ( ! err ) && stop ) {
+ if ((!err) && stop) {
/* STOP, raise data while clock is high */
- TLan_ClearBit( TLAN_NET_SIO_EDATA, sio );
- TLan_SetBit( TLAN_NET_SIO_ECLOK, sio );
- TLan_SetBit( TLAN_NET_SIO_EDATA, sio );
+ tlan_clear_bit(TLAN_NET_SIO_EDATA, sio);
+ tlan_set_bit(TLAN_NET_SIO_ECLOK, sio);
+ tlan_set_bit(TLAN_NET_SIO_EDATA, sio);
}
return err;
-} /* TLan_EeSendByte */
-
-
-
-
- /***************************************************************
- * TLan_EeReceiveByte
- *
- * Returns:
- * Nothing
- * Parms:
- * io_base The IO port base address for the
- * TLAN device with the EEPROM to
- * use.
- * data An address to a char to hold the
- * data sent from the EEPROM.
- * stop If TLAN_EEPROM_STOP is passed, a
- * stop cycle is sent after the
- * byte is received, and no ack is
- * sent.
- *
- * This function receives 8 bits of data from the EEPROM
- * over the serial link. It then sends and ack bit, or no
- * ack and a stop bit. This function is used to retrieve
- * data after the address of a byte in the EEPROM has been
- * sent.
- *
- **************************************************************/
-
-static void TLan_EeReceiveByte( u16 io_base, u8 *data, int stop )
+}
+
+
+
+
+/***************************************************************
+ * tlan_ee_receive_byte
+ *
+ * Returns:
+ * Nothing
+ * Parms:
+ * io_base The IO port base address for the
+ * TLAN device with the EEPROM to
+ * use.
+ * data An address to a char to hold the
+ * data sent from the EEPROM.
+ * stop If TLAN_EEPROM_STOP is passed, a
+ * stop cycle is sent after the
+ * byte is received, and no ack is
+ * sent.
+ *
+ * This function receives 8 bits of data from the EEPROM
+ * over the serial link. It then sends and ack bit, or no
+ * ack and a stop bit. This function is used to retrieve
+ * data after the address of a byte in the EEPROM has been
+ * sent.
+ *
+ **************************************************************/
+
+static void tlan_ee_receive_byte(u16 io_base, u8 *data, int stop)
{
u8 place;
u16 sio;
- outw( TLAN_NET_SIO, io_base + TLAN_DIO_ADR );
+ outw(TLAN_NET_SIO, io_base + TLAN_DIO_ADR);
sio = io_base + TLAN_DIO_DATA + TLAN_NET_SIO;
*data = 0;
/* Assume clock is low, tx is enabled; */
- TLan_ClearBit( TLAN_NET_SIO_ETXEN, sio );
- for ( place = 0x80; place; place >>= 1 ) {
- TLan_SetBit( TLAN_NET_SIO_ECLOK, sio );
- if ( TLan_GetBit( TLAN_NET_SIO_EDATA, sio ) )
+ tlan_clear_bit(TLAN_NET_SIO_ETXEN, sio);
+ for (place = 0x80; place; place >>= 1) {
+ tlan_set_bit(TLAN_NET_SIO_ECLOK, sio);
+ if (tlan_get_bit(TLAN_NET_SIO_EDATA, sio))
*data |= place;
- TLan_ClearBit( TLAN_NET_SIO_ECLOK, sio );
+ tlan_clear_bit(TLAN_NET_SIO_ECLOK, sio);
}
- TLan_SetBit( TLAN_NET_SIO_ETXEN, sio );
- if ( ! stop ) {
- TLan_ClearBit( TLAN_NET_SIO_EDATA, sio ); /* Ack = 0 */
- TLan_SetBit( TLAN_NET_SIO_ECLOK, sio );
- TLan_ClearBit( TLAN_NET_SIO_ECLOK, sio );
+ tlan_set_bit(TLAN_NET_SIO_ETXEN, sio);
+ if (!stop) {
+ tlan_clear_bit(TLAN_NET_SIO_EDATA, sio); /* ack = 0 */
+ tlan_set_bit(TLAN_NET_SIO_ECLOK, sio);
+ tlan_clear_bit(TLAN_NET_SIO_ECLOK, sio);
} else {
- TLan_SetBit( TLAN_NET_SIO_EDATA, sio ); /* No ack = 1 (?) */
- TLan_SetBit( TLAN_NET_SIO_ECLOK, sio );
- TLan_ClearBit( TLAN_NET_SIO_ECLOK, sio );
+ tlan_set_bit(TLAN_NET_SIO_EDATA, sio); /* no ack = 1 (?) */
+ tlan_set_bit(TLAN_NET_SIO_ECLOK, sio);
+ tlan_clear_bit(TLAN_NET_SIO_ECLOK, sio);
/* STOP, raise data while clock is high */
- TLan_ClearBit( TLAN_NET_SIO_EDATA, sio );
- TLan_SetBit( TLAN_NET_SIO_ECLOK, sio );
- TLan_SetBit( TLAN_NET_SIO_EDATA, sio );
- }
-
-} /* TLan_EeReceiveByte */
-
-
-
-
- /***************************************************************
- * TLan_EeReadByte
- *
- * Returns:
- * No error = 0, else, the stage at which the error
- * occurred.
- * Parms:
- * io_base The IO port base address for the
- * TLAN device with the EEPROM to
- * use.
- * ee_addr The address of the byte in the
- * EEPROM whose contents are to be
- * retrieved.
- * data An address to a char to hold the
- * data obtained from the EEPROM.
- *
- * This function reads a byte of information from an byte
- * cell in the EEPROM.
- *
- **************************************************************/
-
-static int TLan_EeReadByte( struct net_device *dev, u8 ee_addr, u8 *data )
+ tlan_clear_bit(TLAN_NET_SIO_EDATA, sio);
+ tlan_set_bit(TLAN_NET_SIO_ECLOK, sio);
+ tlan_set_bit(TLAN_NET_SIO_EDATA, sio);
+ }
+
+}
+
+
+
+
+/***************************************************************
+ * tlan_ee_read_byte
+ *
+ * Returns:
+ * No error = 0, else, the stage at which the error
+ * occurred.
+ * Parms:
+ * io_base The IO port base address for the
+ * TLAN device with the EEPROM to
+ * use.
+ * ee_addr The address of the byte in the
+ * EEPROM whose contents are to be
+ * retrieved.
+ * data An address to a char to hold the
+ * data obtained from the EEPROM.
+ *
+ * This function reads a byte of information from an byte
+ * cell in the EEPROM.
+ *
+ **************************************************************/
+
+static int tlan_ee_read_byte(struct net_device *dev, u8 ee_addr, u8 *data)
{
int err;
- TLanPrivateInfo *priv = netdev_priv(dev);
+ struct tlan_priv *priv = netdev_priv(dev);
unsigned long flags = 0;
- int ret=0;
+ int ret = 0;
spin_lock_irqsave(&priv->lock, flags);
- TLan_EeSendStart( dev->base_addr );
- err = TLan_EeSendByte( dev->base_addr, 0xA0, TLAN_EEPROM_ACK );
- if (err)
- {
- ret=1;
+ tlan_ee_send_start(dev->base_addr);
+ err = tlan_ee_send_byte(dev->base_addr, 0xa0, TLAN_EEPROM_ACK);
+ if (err) {
+ ret = 1;
goto fail;
}
- err = TLan_EeSendByte( dev->base_addr, ee_addr, TLAN_EEPROM_ACK );
- if (err)
- {
- ret=2;
+ err = tlan_ee_send_byte(dev->base_addr, ee_addr, TLAN_EEPROM_ACK);
+ if (err) {
+ ret = 2;
goto fail;
}
- TLan_EeSendStart( dev->base_addr );
- err = TLan_EeSendByte( dev->base_addr, 0xA1, TLAN_EEPROM_ACK );
- if (err)
- {
- ret=3;
+ tlan_ee_send_start(dev->base_addr);
+ err = tlan_ee_send_byte(dev->base_addr, 0xa1, TLAN_EEPROM_ACK);
+ if (err) {
+ ret = 3;
goto fail;
}
- TLan_EeReceiveByte( dev->base_addr, data, TLAN_EEPROM_STOP );
+ tlan_ee_receive_byte(dev->base_addr, data, TLAN_EEPROM_STOP);
fail:
spin_unlock_irqrestore(&priv->lock, flags);
return ret;
-} /* TLan_EeReadByte */
+}
projects / ~shefty / rdma-dev.git / commitdiff