# AT91RM9200 board-specific support
obj-$(CONFIG_MACH_ONEARM) += board-1arm.o
-obj-$(CONFIG_ARCH_AT91RM9200DK) += board-dk.o
-obj-$(CONFIG_MACH_AT91RM9200EK) += board-ek.o
+obj-$(CONFIG_ARCH_AT91RM9200DK) += board-rm9200dk.o
+obj-$(CONFIG_MACH_AT91RM9200EK) += board-rm9200ek.o
obj-$(CONFIG_MACH_CSB337) += board-csb337.o
obj-$(CONFIG_MACH_CSB637) += board-csb637.o
obj-$(CONFIG_MACH_CARMEVA) += board-carmeva.o
+++ /dev/null
-/*
- * linux/arch/arm/mach-at91/board-dk.c
- *
- * Copyright (C) 2005 SAN People
- *
- * Epson S1D framebuffer glue code is:
- * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/board.h>
-#include <mach/gpio.h>
-#include <mach/at91rm9200_mc.h>
-
-#include "generic.h"
-
-
-static void __init dk_map_io(void)
-{
- /* Initialize processor: 18.432 MHz crystal */
- at91rm9200_initialize(18432000, AT91RM9200_BGA);
-
- /* Setup the LEDs */
- at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
-}
-
-static void __init dk_init_irq(void)
-{
- at91rm9200_init_interrupts(NULL);
-}
-
-static struct at91_eth_data __initdata dk_eth_data = {
- .phy_irq_pin = AT91_PIN_PC4,
- .is_rmii = 1,
-};
-
-static struct at91_usbh_data __initdata dk_usbh_data = {
- .ports = 2,
-};
-
-static struct at91_udc_data __initdata dk_udc_data = {
- .vbus_pin = AT91_PIN_PD4,
- .pullup_pin = AT91_PIN_PD5,
-};
-
-static struct at91_cf_data __initdata dk_cf_data = {
- .det_pin = AT91_PIN_PB0,
- .rst_pin = AT91_PIN_PC5,
- // .irq_pin = ... not connected
- // .vcc_pin = ... always powered
-};
-
-#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
-static struct at91_mmc_data __initdata dk_mmc_data = {
- .slot_b = 0,
- .wire4 = 1,
-};
-#endif
-
-static struct spi_board_info dk_spi_devices[] = {
- { /* DataFlash chip */
- .modalias = "mtd_dataflash",
- .chip_select = 0,
- .max_speed_hz = 15 * 1000 * 1000,
- },
- { /* UR6HCPS2-SP40 PS2-to-SPI adapter */
- .modalias = "ur6hcps2",
- .chip_select = 1,
- .max_speed_hz = 250 * 1000,
- },
- { /* TLV1504 ADC, 4 channels, 10 bits; one is a temp sensor */
- .modalias = "tlv1504",
- .chip_select = 2,
- .max_speed_hz = 20 * 1000 * 1000,
- },
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
- { /* DataFlash card */
- .modalias = "mtd_dataflash",
- .chip_select = 3,
- .max_speed_hz = 15 * 1000 * 1000,
- }
-#endif
-};
-
-static struct i2c_board_info __initdata dk_i2c_devices[] = {
- {
- I2C_BOARD_INFO("ics1523", 0x26),
- },
- {
- I2C_BOARD_INFO("x9429", 0x28),
- },
- {
- I2C_BOARD_INFO("24c1024", 0x50),
- }
-};
-
-static struct mtd_partition __initdata dk_nand_partition[] = {
- {
- .name = "NAND Partition 1",
- .offset = 0,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
-{
- *num_partitions = ARRAY_SIZE(dk_nand_partition);
- return dk_nand_partition;
-}
-
-static struct atmel_nand_data __initdata dk_nand_data = {
- .ale = 22,
- .cle = 21,
- .det_pin = AT91_PIN_PB1,
- .rdy_pin = AT91_PIN_PC2,
- // .enable_pin = ... not there
- .partition_info = nand_partitions,
-};
-
-#define DK_FLASH_BASE AT91_CHIPSELECT_0
-#define DK_FLASH_SIZE SZ_2M
-
-static struct physmap_flash_data dk_flash_data = {
- .width = 2,
-};
-
-static struct resource dk_flash_resource = {
- .start = DK_FLASH_BASE,
- .end = DK_FLASH_BASE + DK_FLASH_SIZE - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device dk_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &dk_flash_data,
- },
- .resource = &dk_flash_resource,
- .num_resources = 1,
-};
-
-static struct gpio_led dk_leds[] = {
- {
- .name = "led0",
- .gpio = AT91_PIN_PB2,
- .active_low = 1,
- .default_trigger = "heartbeat",
- }
-};
-
-static void __init dk_board_init(void)
-{
- /* Serial */
- at91_add_device_serial();
- /* Ethernet */
- at91_add_device_eth(&dk_eth_data);
- /* USB Host */
- at91_add_device_usbh(&dk_usbh_data);
- /* USB Device */
- at91_add_device_udc(&dk_udc_data);
- at91_set_multi_drive(dk_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
- /* Compact Flash */
- at91_add_device_cf(&dk_cf_data);
- /* I2C */
- at91_add_device_i2c(dk_i2c_devices, ARRAY_SIZE(dk_i2c_devices));
- /* SPI */
- at91_add_device_spi(dk_spi_devices, ARRAY_SIZE(dk_spi_devices));
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
- /* DataFlash card */
- at91_set_gpio_output(AT91_PIN_PB7, 0);
-#else
- /* MMC */
- at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
- at91_add_device_mmc(0, &dk_mmc_data);
-#endif
- /* NAND */
- at91_add_device_nand(&dk_nand_data);
- /* NOR Flash */
- platform_device_register(&dk_flash);
- /* LEDs */
- at91_gpio_leds(dk_leds, ARRAY_SIZE(dk_leds));
- /* VGA */
-// dk_add_device_video();
-}
-
-MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK")
- /* Maintainer: SAN People/Atmel */
- .boot_params = AT91_SDRAM_BASE + 0x100,
- .timer = &at91rm9200_timer,
- .map_io = dk_map_io,
- .init_irq = dk_init_irq,
- .init_machine = dk_board_init,
-MACHINE_END
+++ /dev/null
-/*
- * linux/arch/arm/mach-at91/board-ek.c
- *
- * Copyright (C) 2005 SAN People
- *
- * Epson S1D framebuffer glue code is:
- * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/board.h>
-#include <mach/gpio.h>
-#include <mach/at91rm9200_mc.h>
-
-#include "generic.h"
-
-
-static void __init ek_map_io(void)
-{
- /* Initialize processor: 18.432 MHz crystal */
- at91rm9200_initialize(18432000, AT91RM9200_BGA);
-
- /* Setup the LEDs */
- at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
-
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
- at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
- | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
- | ATMEL_UART_RI);
-
- /* set serial console to ttyS0 (ie, DBGU) */
- at91_set_serial_console(0);
-}
-
-static void __init ek_init_irq(void)
-{
- at91rm9200_init_interrupts(NULL);
-}
-
-static struct at91_eth_data __initdata ek_eth_data = {
- .phy_irq_pin = AT91_PIN_PC4,
- .is_rmii = 1,
-};
-
-static struct at91_usbh_data __initdata ek_usbh_data = {
- .ports = 2,
-};
-
-static struct at91_udc_data __initdata ek_udc_data = {
- .vbus_pin = AT91_PIN_PD4,
- .pullup_pin = AT91_PIN_PD5,
-};
-
-#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
-static struct at91_mmc_data __initdata ek_mmc_data = {
- .det_pin = AT91_PIN_PB27,
- .slot_b = 0,
- .wire4 = 1,
- .wp_pin = AT91_PIN_PA17,
-};
-#endif
-
-static struct spi_board_info ek_spi_devices[] = {
- { /* DataFlash chip */
- .modalias = "mtd_dataflash",
- .chip_select = 0,
- .max_speed_hz = 15 * 1000 * 1000,
- },
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
- { /* DataFlash card */
- .modalias = "mtd_dataflash",
- .chip_select = 3,
- .max_speed_hz = 15 * 1000 * 1000,
- },
-#endif
-};
-
-static struct i2c_board_info __initdata ek_i2c_devices[] = {
- {
- I2C_BOARD_INFO("ics1523", 0x26),
- },
- {
- I2C_BOARD_INFO("dac3550", 0x4d),
- }
-};
-
-#define EK_FLASH_BASE AT91_CHIPSELECT_0
-#define EK_FLASH_SIZE SZ_2M
-
-static struct physmap_flash_data ek_flash_data = {
- .width = 2,
-};
-
-static struct resource ek_flash_resource = {
- .start = EK_FLASH_BASE,
- .end = EK_FLASH_BASE + EK_FLASH_SIZE - 1,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ek_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &ek_flash_data,
- },
- .resource = &ek_flash_resource,
- .num_resources = 1,
-};
-
-static struct gpio_led ek_leds[] = {
- { /* "user led 1", DS2 */
- .name = "green",
- .gpio = AT91_PIN_PB0,
- .active_low = 1,
- .default_trigger = "mmc0",
- },
- { /* "user led 2", DS4 */
- .name = "yellow",
- .gpio = AT91_PIN_PB1,
- .active_low = 1,
- .default_trigger = "heartbeat",
- },
- { /* "user led 3", DS6 */
- .name = "red",
- .gpio = AT91_PIN_PB2,
- .active_low = 1,
- }
-};
-
-static void __init ek_board_init(void)
-{
- /* Serial */
- at91_add_device_serial();
- /* Ethernet */
- at91_add_device_eth(&ek_eth_data);
- /* USB Host */
- at91_add_device_usbh(&ek_usbh_data);
- /* USB Device */
- at91_add_device_udc(&ek_udc_data);
- at91_set_multi_drive(ek_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
- /* I2C */
- at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
- /* SPI */
- at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
- /* DataFlash card */
- at91_set_gpio_output(AT91_PIN_PB22, 0);
-#else
- /* MMC */
- at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
- at91_add_device_mmc(0, &ek_mmc_data);
-#endif
- /* NOR Flash */
- platform_device_register(&ek_flash);
- /* LEDs */
- at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
- /* VGA */
-// ek_add_device_video();
-}
-
-MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
- /* Maintainer: SAN People/Atmel */
- .boot_params = AT91_SDRAM_BASE + 0x100,
- .timer = &at91rm9200_timer,
- .map_io = ek_map_io,
- .init_irq = ek_init_irq,
- .init_machine = ek_board_init,
-MACHINE_END
--- /dev/null
+/*
+ * linux/arch/arm/mach-at91/board-rm9200dk.c
+ *
+ * Copyright (C) 2005 SAN People
+ *
+ * Epson S1D framebuffer glue code is:
+ * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200_mc.h>
+
+#include "generic.h"
+
+
+static void __init dk_map_io(void)
+{
+ /* Initialize processor: 18.432 MHz crystal */
+ at91rm9200_initialize(18432000, AT91RM9200_BGA);
+
+ /* Setup the LEDs */
+ at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
+
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
+}
+
+static void __init dk_init_irq(void)
+{
+ at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata dk_eth_data = {
+ .phy_irq_pin = AT91_PIN_PC4,
+ .is_rmii = 1,
+};
+
+static struct at91_usbh_data __initdata dk_usbh_data = {
+ .ports = 2,
+};
+
+static struct at91_udc_data __initdata dk_udc_data = {
+ .vbus_pin = AT91_PIN_PD4,
+ .pullup_pin = AT91_PIN_PD5,
+};
+
+static struct at91_cf_data __initdata dk_cf_data = {
+ .det_pin = AT91_PIN_PB0,
+ .rst_pin = AT91_PIN_PC5,
+ // .irq_pin = ... not connected
+ // .vcc_pin = ... always powered
+};
+
+#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
+static struct at91_mmc_data __initdata dk_mmc_data = {
+ .slot_b = 0,
+ .wire4 = 1,
+};
+#endif
+
+static struct spi_board_info dk_spi_devices[] = {
+ { /* DataFlash chip */
+ .modalias = "mtd_dataflash",
+ .chip_select = 0,
+ .max_speed_hz = 15 * 1000 * 1000,
+ },
+ { /* UR6HCPS2-SP40 PS2-to-SPI adapter */
+ .modalias = "ur6hcps2",
+ .chip_select = 1,
+ .max_speed_hz = 250 * 1000,
+ },
+ { /* TLV1504 ADC, 4 channels, 10 bits; one is a temp sensor */
+ .modalias = "tlv1504",
+ .chip_select = 2,
+ .max_speed_hz = 20 * 1000 * 1000,
+ },
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+ { /* DataFlash card */
+ .modalias = "mtd_dataflash",
+ .chip_select = 3,
+ .max_speed_hz = 15 * 1000 * 1000,
+ }
+#endif
+};
+
+static struct i2c_board_info __initdata dk_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("ics1523", 0x26),
+ },
+ {
+ I2C_BOARD_INFO("x9429", 0x28),
+ },
+ {
+ I2C_BOARD_INFO("24c1024", 0x50),
+ }
+};
+
+static struct mtd_partition __initdata dk_nand_partition[] = {
+ {
+ .name = "NAND Partition 1",
+ .offset = 0,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+ *num_partitions = ARRAY_SIZE(dk_nand_partition);
+ return dk_nand_partition;
+}
+
+static struct atmel_nand_data __initdata dk_nand_data = {
+ .ale = 22,
+ .cle = 21,
+ .det_pin = AT91_PIN_PB1,
+ .rdy_pin = AT91_PIN_PC2,
+ // .enable_pin = ... not there
+ .partition_info = nand_partitions,
+};
+
+#define DK_FLASH_BASE AT91_CHIPSELECT_0
+#define DK_FLASH_SIZE SZ_2M
+
+static struct physmap_flash_data dk_flash_data = {
+ .width = 2,
+};
+
+static struct resource dk_flash_resource = {
+ .start = DK_FLASH_BASE,
+ .end = DK_FLASH_BASE + DK_FLASH_SIZE - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device dk_flash = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &dk_flash_data,
+ },
+ .resource = &dk_flash_resource,
+ .num_resources = 1,
+};
+
+static struct gpio_led dk_leds[] = {
+ {
+ .name = "led0",
+ .gpio = AT91_PIN_PB2,
+ .active_low = 1,
+ .default_trigger = "heartbeat",
+ }
+};
+
+static void __init dk_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* Ethernet */
+ at91_add_device_eth(&dk_eth_data);
+ /* USB Host */
+ at91_add_device_usbh(&dk_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&dk_udc_data);
+ at91_set_multi_drive(dk_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
+ /* Compact Flash */
+ at91_add_device_cf(&dk_cf_data);
+ /* I2C */
+ at91_add_device_i2c(dk_i2c_devices, ARRAY_SIZE(dk_i2c_devices));
+ /* SPI */
+ at91_add_device_spi(dk_spi_devices, ARRAY_SIZE(dk_spi_devices));
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+ /* DataFlash card */
+ at91_set_gpio_output(AT91_PIN_PB7, 0);
+#else
+ /* MMC */
+ at91_set_gpio_output(AT91_PIN_PB7, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
+ at91_add_device_mmc(0, &dk_mmc_data);
+#endif
+ /* NAND */
+ at91_add_device_nand(&dk_nand_data);
+ /* NOR Flash */
+ platform_device_register(&dk_flash);
+ /* LEDs */
+ at91_gpio_leds(dk_leds, ARRAY_SIZE(dk_leds));
+ /* VGA */
+// dk_add_device_video();
+}
+
+MACHINE_START(AT91RM9200DK, "Atmel AT91RM9200-DK")
+ /* Maintainer: SAN People/Atmel */
+ .boot_params = AT91_SDRAM_BASE + 0x100,
+ .timer = &at91rm9200_timer,
+ .map_io = dk_map_io,
+ .init_irq = dk_init_irq,
+ .init_machine = dk_board_init,
+MACHINE_END
--- /dev/null
+/*
+ * linux/arch/arm/mach-at91/board-rm9200ek.c
+ *
+ * Copyright (C) 2005 SAN People
+ *
+ * Epson S1D framebuffer glue code is:
+ * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91rm9200_mc.h>
+
+#include "generic.h"
+
+
+static void __init ek_map_io(void)
+{
+ /* Initialize processor: 18.432 MHz crystal */
+ at91rm9200_initialize(18432000, AT91RM9200_BGA);
+
+ /* Setup the LEDs */
+ at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
+
+ /* DBGU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
+}
+
+static void __init ek_init_irq(void)
+{
+ at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata ek_eth_data = {
+ .phy_irq_pin = AT91_PIN_PC4,
+ .is_rmii = 1,
+};
+
+static struct at91_usbh_data __initdata ek_usbh_data = {
+ .ports = 2,
+};
+
+static struct at91_udc_data __initdata ek_udc_data = {
+ .vbus_pin = AT91_PIN_PD4,
+ .pullup_pin = AT91_PIN_PD5,
+};
+
+#ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
+static struct at91_mmc_data __initdata ek_mmc_data = {
+ .det_pin = AT91_PIN_PB27,
+ .slot_b = 0,
+ .wire4 = 1,
+ .wp_pin = AT91_PIN_PA17,
+};
+#endif
+
+static struct spi_board_info ek_spi_devices[] = {
+ { /* DataFlash chip */
+ .modalias = "mtd_dataflash",
+ .chip_select = 0,
+ .max_speed_hz = 15 * 1000 * 1000,
+ },
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+ { /* DataFlash card */
+ .modalias = "mtd_dataflash",
+ .chip_select = 3,
+ .max_speed_hz = 15 * 1000 * 1000,
+ },
+#endif
+};
+
+static struct i2c_board_info __initdata ek_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("ics1523", 0x26),
+ },
+ {
+ I2C_BOARD_INFO("dac3550", 0x4d),
+ }
+};
+
+#define EK_FLASH_BASE AT91_CHIPSELECT_0
+#define EK_FLASH_SIZE SZ_2M
+
+static struct physmap_flash_data ek_flash_data = {
+ .width = 2,
+};
+
+static struct resource ek_flash_resource = {
+ .start = EK_FLASH_BASE,
+ .end = EK_FLASH_BASE + EK_FLASH_SIZE - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device ek_flash = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &ek_flash_data,
+ },
+ .resource = &ek_flash_resource,
+ .num_resources = 1,
+};
+
+static struct gpio_led ek_leds[] = {
+ { /* "user led 1", DS2 */
+ .name = "green",
+ .gpio = AT91_PIN_PB0,
+ .active_low = 1,
+ .default_trigger = "mmc0",
+ },
+ { /* "user led 2", DS4 */
+ .name = "yellow",
+ .gpio = AT91_PIN_PB1,
+ .active_low = 1,
+ .default_trigger = "heartbeat",
+ },
+ { /* "user led 3", DS6 */
+ .name = "red",
+ .gpio = AT91_PIN_PB2,
+ .active_low = 1,
+ }
+};
+
+static void __init ek_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* Ethernet */
+ at91_add_device_eth(&ek_eth_data);
+ /* USB Host */
+ at91_add_device_usbh(&ek_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&ek_udc_data);
+ at91_set_multi_drive(ek_udc_data.pullup_pin, 1); /* pullup_pin is connected to reset */
+ /* I2C */
+ at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
+ /* SPI */
+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+#ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
+ /* DataFlash card */
+ at91_set_gpio_output(AT91_PIN_PB22, 0);
+#else
+ /* MMC */
+ at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
+ at91_add_device_mmc(0, &ek_mmc_data);
+#endif
+ /* NOR Flash */
+ platform_device_register(&ek_flash);
+ /* LEDs */
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+ /* VGA */
+// ek_add_device_video();
+}
+
+MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
+ /* Maintainer: SAN People/Atmel */
+ .boot_params = AT91_SDRAM_BASE + 0x100,
+ .timer = &at91rm9200_timer,
+ .map_io = ek_map_io,
+ .init_irq = ek_init_irq,
+ .init_machine = ek_board_init,
+MACHINE_END
projects / ~emulex / infiniband.git / commitdiff