source "drivers/staging/westbridge/Kconfig"
+source "drivers/staging/sbe-2t3e3/Kconfig"
+
endif # !STAGING_EXCLUDE_BUILD
endif # STAGING
obj-$(CONFIG_TIDSPBRIDGE) += tidspbridge/
obj-$(CONFIG_ACPI_QUICKSTART) += quickstart/
obj-$(CONFIG_WESTBRIDGE_ASTORIA) += westbridge/astoria/
+obj-$(CONFIG_SBE_2T3E3) += sbe-2t3e3/
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#ifndef T3E3_H
+#define T3E3_H
+
+#include <linux/hdlc.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/pci.h>
+#include <linux/io.h>
+#include "ctrl.h"
+
+/**************************************************************
+ * 21143
+ **************************************************************/
+
+/* CSR */
+#define SBE_2T3E3_21143_REG_BUS_MODE 0
+#define SBE_2T3E3_21143_REG_TRANSMIT_POLL_DEMAND 1
+#define SBE_2T3E3_21143_REG_RECEIVE_POLL_DEMAND 2
+#define SBE_2T3E3_21143_REG_RECEIVE_LIST_BASE_ADDRESS 3
+#define SBE_2T3E3_21143_REG_TRANSMIT_LIST_BASE_ADDRESS 4
+#define SBE_2T3E3_21143_REG_STATUS 5
+#define SBE_2T3E3_21143_REG_OPERATION_MODE 6
+#define SBE_2T3E3_21143_REG_INTERRUPT_ENABLE 7
+#define SBE_2T3E3_21143_REG_MISSED_FRAMES_AND_OVERFLOW_COUNTER 8
+#define SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT 9
+#define SBE_2T3E3_21143_REG_BOOT_ROM_PROGRAMMING_ADDRESS 10
+#define SBE_2T3E3_21143_REG_GENERAL_PURPOSE_TIMER_AND_INTERRUPT_MITIGATION_CONTROL 11
+#define SBE_2T3E3_21143_REG_SIA_STATUS 12
+#define SBE_2T3E3_21143_REG_SIA_CONNECTIVITY 13
+#define SBE_2T3E3_21143_REG_SIA_TRANSMIT_AND_RECEIVE 14
+#define SBE_2T3E3_21143_REG_SIA_AND_GENERAL_PURPOSE_PORT 15
+#define SBE_2T3E3_21143_REG_MAX 16
+
+/* CSR0 - BUS_MODE */
+#define SBE_2T3E3_21143_VAL_WRITE_AND_INVALIDATE_ENABLE 0x01000000
+#define SBE_2T3E3_21143_VAL_READ_LINE_ENABLE 0x00800000
+#define SBE_2T3E3_21143_VAL_READ_MULTIPLE_ENABLE 0x00200000
+#define SBE_2T3E3_21143_VAL_TRANSMIT_AUTOMATIC_POLLING_200us 0x00020000
+#define SBE_2T3E3_21143_VAL_TRANSMIT_AUTOMATIC_POLLING_DISABLED 0x00000000
+#define SBE_2T3E3_21143_VAL_CACHE_ALIGNMENT_32 0x0000c000
+#define SBE_2T3E3_21143_VAL_CACHE_ALIGNMENT_16 0x00008000
+#define SBE_2T3E3_21143_VAL_CACHE_ALIGNMENT_8 0x00004000
+#define SBE_2T3E3_21143_VAL_BUS_ARBITRATION_RR 0x00000002
+#define SBE_2T3E3_21143_VAL_SOFTWARE_RESET 0x00000001
+
+/* CSR5 - STATUS */
+#define SBE_2T3E3_21143_VAL_GENERAL_PURPOSE_PORT_INTERRUPT 0x04000000
+#define SBE_2T3E3_21143_VAL_ERROR_BITS 0x03800000
+#define SBE_2T3E3_21143_VAL_PARITY_ERROR 0x00000000
+#define SBE_2T3E3_21143_VAL_MASTER_ABORT 0x00800000
+#define SBE_2T3E3_21143_VAL_TARGET_ABORT 0x01000000
+#define SBE_2T3E3_21143_VAL_TRANSMISSION_PROCESS_STATE 0x00700000
+#define SBE_2T3E3_21143_VAL_TX_STOPPED 0x00000000
+#define SBE_2T3E3_21143_VAL_TX_SUSPENDED 0x00600000
+#define SBE_2T3E3_21143_VAL_RECEIVE_PROCESS_STATE 0x000e0000
+#define SBE_2T3E3_21143_VAL_RX_STOPPED 0x00000000
+#define SBE_2T3E3_21143_VAL_RX_SUSPENDED 0x000a0000
+#define SBE_2T3E3_21143_VAL_NORMAL_INTERRUPT_SUMMARY 0x00010000
+#define SBE_2T3E3_21143_VAL_ABNORMAL_INTERRUPT_SUMMARY 0x00008000
+#define SBE_2T3E3_21143_VAL_EARLY_RECEIVE_INTERRUPT 0x00004000
+#define SBE_2T3E3_21143_VAL_FATAL_BUS_ERROR 0x00002000
+#define SBE_2T3E3_21143_VAL_GENERAL_PURPOSE_TIMER_EXPIRED 0x00000800
+#define SBE_2T3E3_21143_VAL_EARLY_TRANSMIT_INTERRUPT 0x00000400
+#define SBE_2T3E3_21143_VAL_RECEIVE_WATCHDOG_TIMEOUT 0x00000200
+#define SBE_2T3E3_21143_VAL_RECEIVE_PROCESS_STOPPED 0x00000100
+#define SBE_2T3E3_21143_VAL_RECEIVE_BUFFER_UNAVAILABLE 0x00000080
+#define SBE_2T3E3_21143_VAL_RECEIVE_INTERRUPT 0x00000040
+#define SBE_2T3E3_21143_VAL_TRANSMIT_UNDERFLOW 0x00000020
+#define SBE_2T3E3_21143_VAL_TRANSMIT_JABBER_TIMEOUT 0x00000008
+#define SBE_2T3E3_21143_VAL_TRANSMIT_BUFFER_UNAVAILABLE 0x00000004
+#define SBE_2T3E3_21143_VAL_TRANSMIT_PROCESS_STOPPED 0x00000002
+#define SBE_2T3E3_21143_VAL_TRANSMIT_INTERRUPT 0x00000001
+
+/* CSR6 - OPERATION_MODE */
+#define SBE_2T3E3_21143_VAL_SPECIAL_CAPTURE_EFFECT_ENABLE 0x80000000
+#define SBE_2T3E3_21143_VAL_RECEIVE_ALL 0x40000000
+#define SBE_2T3E3_21143_VAL_MUST_BE_ONE 0x02000000
+#define SBE_2T3E3_21143_VAL_SCRAMBLER_MODE 0x01000000
+#define SBE_2T3E3_21143_VAL_PCS_FUNCTION 0x00800000
+#define SBE_2T3E3_21143_VAL_TRANSMIT_THRESHOLD_MODE_10Mbs 0x00400000
+#define SBE_2T3E3_21143_VAL_TRANSMIT_THRESHOLD_MODE_100Mbs 0x00000000
+#define SBE_2T3E3_21143_VAL_STORE_AND_FORWARD 0x00200000
+#define SBE_2T3E3_21143_VAL_HEARTBEAT_DISABLE 0x00080000
+#define SBE_2T3E3_21143_VAL_PORT_SELECT 0x00040000
+#define SBE_2T3E3_21143_VAL_CAPTURE_EFFECT_ENABLE 0x00020000
+#define SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS 0x0000c000
+#define SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_1 0x00000000
+#define SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_2 0x00004000
+#define SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_3 0x00008000
+#define SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_4 0x0000c000
+#define SBE_2T3E3_21143_VAL_TRANSMISSION_START 0x00002000
+#define SBE_2T3E3_21143_VAL_OPERATING_MODE 0x00000c00
+#define SBE_2T3E3_21143_VAL_LOOPBACK_OFF 0x00000000
+#define SBE_2T3E3_21143_VAL_LOOPBACK_EXTERNAL 0x00000800
+#define SBE_2T3E3_21143_VAL_LOOPBACK_INTERNAL 0x00000400
+#define SBE_2T3E3_21143_VAL_FULL_DUPLEX_MODE 0x00000200
+#define SBE_2T3E3_21143_VAL_PASS_ALL_MULTICAST 0x00000080
+#define SBE_2T3E3_21143_VAL_PROMISCUOUS_MODE 0x00000040
+#define SBE_2T3E3_21143_VAL_PASS_BAD_FRAMES 0x00000008
+#define SBE_2T3E3_21143_VAL_RECEIVE_START 0x00000002
+
+/* CSR7 - INTERRUPT_ENABLE */
+#define SBE_2T3E3_21143_VAL_LINK_CHANGED_ENABLE 0x08000000
+#define SBE_2T3E3_21143_VAL_GENERAL_PURPOSE_PORT_ENABLE 0x04000000
+#define SBE_2T3E3_21143_VAL_NORMAL_INTERRUPT_SUMMARY_ENABLE 0x00010000
+#define SBE_2T3E3_21143_VAL_ABNORMAL_INTERRUPT_SUMMARY_ENABLE 0x00008000
+#define SBE_2T3E3_21143_VAL_EARLY_RECEIVE_INTERRUPT_ENABLE 0x00004000
+#define SBE_2T3E3_21143_VAL_FATAL_BUS_ERROR_ENABLE 0x00002000
+#define SBE_2T3E3_21143_VAL_LINK_FAIL_ENABLE 0x00001000
+#define SBE_2T3E3_21143_VAL_GENERAL_PURPOSE_TIMER_ENABLE 0x00000800
+#define SBE_2T3E3_21143_VAL_EARLY_TRANSMIT_INTERRUPT_ENABLE 0x00000400
+#define SBE_2T3E3_21143_VAL_RECEIVE_WATCHDOG_TIMEOUT_ENABLE 0x00000200
+#define SBE_2T3E3_21143_VAL_RECEIVE_STOPPED_ENABLE 0x00000100
+#define SBE_2T3E3_21143_VAL_RECEIVE_BUFFER_UNAVAILABLE_ENABLE 0x00000080
+#define SBE_2T3E3_21143_VAL_RECEIVE_INTERRUPT_ENABLE 0x00000040
+#define SBE_2T3E3_21143_VAL_TRANSMIT_UNDERFLOW_INTERRUPT_ENABLE 0x00000020
+#define SBE_2T3E3_21143_VAL_TRANSMIT_JABBER_TIMEOUT_ENABLE 0x00000008
+#define SBE_2T3E3_21143_VAL_TRANSMIT_BUFFER_UNAVAILABLE_ENABLE 0x00000004
+#define SBE_2T3E3_21143_VAL_TRANSMIT_STOPPED_ENABLE 0x00000002
+#define SBE_2T3E3_21143_VAL_TRANSMIT_INTERRUPT_ENABLE 0x00000001
+
+/* CSR8 - MISSED_FRAMES_AND_OVERFLOW_COUNTER */
+#define SBE_2T3E3_21143_VAL_OVERFLOW_COUNTER_OVERFLOW 0x10000000
+#define SBE_2T3E3_21143_VAL_OVERFLOW_COUNTER 0x0ffe0000
+#define SBE_2T3E3_21143_VAL_MISSED_FRAME_OVERFLOW 0x00010000
+#define SBE_2T3E3_21143_VAL_MISSED_FRAMES_COUNTER 0x0000ffff
+
+/* CSR9 - BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT */
+#define SBE_2T3E3_21143_VAL_MII_MANAGEMENT_DATA_IN 0x00080000
+#define SBE_2T3E3_21143_VAL_MII_MANAGEMENT_READ_MODE 0x00040000
+#define SBE_2T3E3_21143_VAL_MII_MANAGEMENT_DATA_OUT 0x00020000
+#define SBE_2T3E3_21143_VAL_MII_MANAGEMENT_CLOCK 0x00010000
+#define SBE_2T3E3_21143_VAL_READ_OPERATION 0x00004000
+#define SBE_2T3E3_21143_VAL_WRITE_OPERATION 0x00002000
+#define SBE_2T3E3_21143_VAL_BOOT_ROM_SELECT 0x00001000
+#define SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT 0x00000800
+#define SBE_2T3E3_21143_VAL_BOOT_ROM_DATA 0x000000ff
+#define SBE_2T3E3_21143_VAL_SERIAL_ROM_DATA_OUT 0x00000008
+#define SBE_2T3E3_21143_VAL_SERIAL_ROM_DATA_IN 0x00000004
+#define SBE_2T3E3_21143_VAL_SERIAL_ROM_CLOCK 0x00000002
+#define SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT 0x00000001
+
+/* CSR11 - GENERAL_PURPOSE_TIMER_AND_INTERRUPT_MITIGATION_CONTROL */
+#define SBE_2T3E3_21143_VAL_CYCLE_SIZE 0x80000000
+#define SBE_2T3E3_21143_VAL_TRANSMIT_TIMER 0x78000000
+#define SBE_2T3E3_21143_VAL_NUMBER_OF_TRANSMIT_PACKETS 0x07000000
+#define SBE_2T3E3_21143_VAL_RECEIVE_TIMER 0x00f00000
+#define SBE_2T3E3_21143_VAL_NUMBER_OF_RECEIVE_PACKETS 0x000e0000
+#define SBE_2T3E3_21143_VAL_CONTINUOUS_MODE 0x00010000
+#define SBE_2T3E3_21143_VAL_TIMER_VALUE 0x0000ffff
+
+/* CSR12 - SIA_STATUS */
+#define SBE_2T3E3_21143_VAL_10BASE_T_RECEIVE_PORT_ACTIVITY 0x00000200
+#define SBE_2T3E3_21143_VAL_AUI_RECEIVE_PORT_ACTIVITY 0x00000100
+#define SBE_2T3E3_21143_VAL_10Mbs_LINK_STATUS 0x00000004
+#define SBE_2T3E3_21143_VAL_100Mbs_LINK_STATUS 0x00000002
+#define SBE_2T3E3_21143_VAL_MII_RECEIVE_PORT_ACTIVITY 0x00000001
+
+/* CSR13 - SIA_CONNECTIVITY */
+#define SBE_2T3E3_21143_VAL_10BASE_T_OR_AUI 0x00000008
+#define SBE_2T3E3_21143_VAL_SIA_RESET 0x00000001
+
+/* CSR14 - SIA_TRANSMIT_AND_RECEIVE */
+#define SBE_2T3E3_21143_VAL_100BASE_TX_FULL_DUPLEX 0x00020000
+#define SBE_2T3E3_21143_VAL_COLLISION_DETECT_ENABLE 0x00000400
+#define SBE_2T3E3_21143_VAL_COLLISION_SQUELCH_ENABLE 0x00000200
+#define SBE_2T3E3_21143_VAL_RECEIVE_SQUELCH_ENABLE 0x00000100
+#define SBE_2T3E3_21143_VAL_LINK_PULSE_SEND_ENABLE 0x00000004
+#define SBE_2T3E3_21143_VAL_ENCODER_ENABLE 0x00000001
+
+/* CSR15 - SIA_AND_GENERAL_PURPOSE_PORT */
+#define SBE_2T3E3_21143_VAL_RECEIVE_WATCHDOG_DISABLE 0x00000010
+#define SBE_2T3E3_21143_VAL_AUI_BNC_MODE 0x00000008
+#define SBE_2T3E3_21143_VAL_HOST_UNJAB 0x00000002
+#define SBE_2T3E3_21143_VAL_JABBER_DISABLE 0x00000001
+
+/**************************************************************
+ * CPLD
+ **************************************************************/
+
+/* reg_map indexes */
+#define SBE_2T3E3_CPLD_REG_PCRA 0
+#define SBE_2T3E3_CPLD_REG_PCRB 1
+#define SBE_2T3E3_CPLD_REG_PLCR 2
+#define SBE_2T3E3_CPLD_REG_PLTR 3
+#define SBE_2T3E3_CPLD_REG_PPFR 4
+#define SBE_2T3E3_CPLD_REG_BOARD_ID 5
+#define SBE_2T3E3_CPLD_REG_FPGA_VERSION 6
+#define SBE_2T3E3_CPLD_REG_FRAMER_BASE_ADDRESS 7
+#define SBE_2T3E3_CPLD_REG_SERIAL_CHIP_SELECT 8
+#define SBE_2T3E3_CPLD_REG_STATIC_RESET 9
+#define SBE_2T3E3_CPLD_REG_PULSE_RESET 10
+#define SBE_2T3E3_CPLD_REG_FPGA_RECONFIGURATION 11
+#define SBE_2T3E3_CPLD_REG_LEDR 12
+#define SBE_2T3E3_CPLD_REG_PICSR 13
+#define SBE_2T3E3_CPLD_REG_PIER 14
+#define SBE_2T3E3_CPLD_REG_PCRC 15
+#define SBE_2T3E3_CPLD_REG_PBWF 16
+#define SBE_2T3E3_CPLD_REG_PBWL 17
+
+#define SBE_2T3E3_CPLD_REG_MAX 18
+
+/**********/
+
+/* val_map indexes */
+#define SBE_2T3E3_CPLD_VAL_LIU_SELECT 0
+#define SBE_2T3E3_CPLD_VAL_DAC_SELECT 1
+#define SBE_2T3E3_CPLD_VAL_LOOP_TIMING_SOURCE 2
+#define SBE_2T3E3_CPLD_VAL_LIU_FRAMER_RESET 3
+
+/* PCRA */
+#define SBE_2T3E3_CPLD_VAL_CRC32 0x40
+#define SBE_2T3E3_CPLD_VAL_TRANSPARENT_MODE 0x20
+#define SBE_2T3E3_CPLD_VAL_REAR_PANEL 0x10
+#define SBE_2T3E3_CPLD_VAL_RAW_MODE 0x08
+#define SBE_2T3E3_CPLD_VAL_ALT 0x04
+#define SBE_2T3E3_CPLD_VAL_LOOP_TIMING 0x02
+#define SBE_2T3E3_CPLD_VAL_LOCAL_CLOCK_E3 0x01
+
+/* PCRB */
+#define SBE_2T3E3_CPLD_VAL_PAD_COUNT 0x30
+#define SBE_2T3E3_CPLD_VAL_PAD_COUNT_1 0x00
+#define SBE_2T3E3_CPLD_VAL_PAD_COUNT_2 0x10
+#define SBE_2T3E3_CPLD_VAL_PAD_COUNT_3 0x20
+#define SBE_2T3E3_CPLD_VAL_PAD_COUNT_4 0x30
+#define SBE_2T3E3_CPLD_VAL_SCRAMBLER_TYPE 0x02
+#define SBE_2T3E3_CPLD_VAL_SCRAMBLER_ENABLE 0x01
+
+/* PCRC */
+#define SBE_2T3E3_CPLD_VAL_FRACTIONAL_MODE_NONE 0x00
+#define SBE_2T3E3_CPLD_VAL_FRACTIONAL_MODE_0 0x01
+#define SBE_2T3E3_CPLD_VAL_FRACTIONAL_MODE_1 0x11
+#define SBE_2T3E3_CPLD_VAL_FRACTIONAL_MODE_2 0x21
+
+/* PLTR */
+#define SBE_2T3E3_CPLD_VAL_LCV_COUNTER 0xff
+
+/* SCSR */
+#define SBE_2T3E3_CPLD_VAL_EEPROM_SELECT 0x10
+
+/* PICSR */
+#define SBE_2T3E3_CPLD_VAL_LOSS_OF_SIGNAL_THRESHOLD_LEVEL_1 0x80
+#define SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_SIGNAL_CHANGE 0x40
+#define SBE_2T3E3_CPLD_VAL_INTERRUPT_FROM_ETHERNET_ASSERTED 0x20
+#define SBE_2T3E3_CPLD_VAL_INTERRUPT_FROM_FRAMER_ASSERTED 0x10
+#define SBE_2T3E3_CPLD_VAL_LCV_LIMIT_EXCEEDED 0x08
+#define SBE_2T3E3_CPLD_VAL_DMO_SIGNAL_DETECTED 0x04
+#define SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_LOCK_DETECTED 0x02
+#define SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_SIGNAL_DETECTED 0x01
+
+/* PIER */
+#define SBE_2T3E3_CPLD_VAL_RECEIVE_LOS_CHANGE_ENABLE 0x40
+#define SBE_2T3E3_CPLD_VAL_INTERRUPT_FROM_ETHERNET_ENABLE 0x20
+#define SBE_2T3E3_CPLD_VAL_INTERRUPT_FROM_FRAMER_ENABLE 0x10
+#define SBE_2T3E3_CPLD_VAL_LCV_INTERRUPT_ENABLE 0x08
+#define SBE_2T3E3_CPLD_VAL_DMO_ENABLE 0x04
+#define SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_LOCK_ENABLE 0x02
+#define SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_SIGNAL_ENABLE 0x01
+
+/**************************************************************
+ * Framer
+ **************************************************************/
+
+/* reg_map indexes */
+/* common */
+#define SBE_2T3E3_FRAMER_REG_OPERATING_MODE 0
+#define SBE_2T3E3_FRAMER_REG_IO_CONTROL 1
+#define SBE_2T3E3_FRAMER_REG_BLOCK_INTERRUPT_ENABLE 2
+#define SBE_2T3E3_FRAMER_REG_BLOCK_INTERRUPT_STATUS 3
+#define SBE_2T3E3_FRAMER_REG_PMON_LCV_EVENT_COUNT_MSB 28
+#define SBE_2T3E3_FRAMER_REG_PMON_LCV_EVENT_COUNT_LSB 29
+#define SBE_2T3E3_FRAMER_REG_PMON_FRAMING_BIT_ERROR_EVENT_COUNT_MSB 30
+#define SBE_2T3E3_FRAMER_REG_PMON_FRAMING_BIT_ERROR_EVENT_COUNT_LSB 31
+#define SBE_2T3E3_FRAMER_REG_PMON_PARITY_ERROR_EVENT_COUNT_MSB 32
+#define SBE_2T3E3_FRAMER_REG_PMON_PARITY_ERROR_EVENT_COUNT_LSB 33
+#define SBE_2T3E3_FRAMER_REG_PMON_FEBE_EVENT_COUNT_MSB 34
+#define SBE_2T3E3_FRAMER_REG_PMON_FEBE_EVENT_COUNT_LSB 35
+#define SBE_2T3E3_FRAMER_REG_PMON_CP_BIT_ERROR_EVENT_COUNT_MSB 36
+#define SBE_2T3E3_FRAMER_REG_PMON_CP_BIT_ERROR_EVENT_COUNT_LSB 37
+#define SBE_2T3E3_FRAMER_REG_PMON_HOLDING_REGISTER 38
+#define SBE_2T3E3_FRAMER_REG_ONE_SECOND_ERROR_STATUS 39
+#define SBE_2T3E3_FRAMER_REG_LCV_ONE_SECOND_ACCUMULATOR_MSB 40
+#define SBE_2T3E3_FRAMER_REG_LCV_ONE_SECOND_ACCUMULATOR_LSB 41
+#define SBE_2T3E3_FRAMER_REG_FRAME_PARITY_ERROR_ONE_SECOND_ACCUMULATOR_MSB 42
+#define SBE_2T3E3_FRAMER_REG_FRAME_PARITY_ERROR_ONE_SECOND_ACCUMULATOR_LSB 43
+#define SBE_2T3E3_FRAMER_REG_FRAME_CP_BIT_ERROR_ONE_SECOND_ACCUMULATOR_MSB 44
+#define SBE_2T3E3_FRAMER_REG_FRAME_CP_BIT_ERROR_ONE_SECOND_ACCUMULATOR_LSB 45
+#define SBE_2T3E3_FRAMER_REG_LINE_INTERFACE_DRIVE 46
+#define SBE_2T3E3_FRAMER_REG_LINE_INTERFACE_SCAN 47
+
+/* T3 */
+#define SBE_2T3E3_FRAMER_REG_T3_RX_CONFIGURATION_STATUS 4
+#define SBE_2T3E3_FRAMER_REG_T3_RX_STATUS 5
+#define SBE_2T3E3_FRAMER_REG_T3_RX_INTERRUPT_ENABLE 6
+#define SBE_2T3E3_FRAMER_REG_T3_RX_INTERRUPT_STATUS 7
+#define SBE_2T3E3_FRAMER_REG_T3_RX_SYNC_DETECT_ENABLE 8
+#define SBE_2T3E3_FRAMER_REG_T3_RX_FEAC 10
+#define SBE_2T3E3_FRAMER_REG_T3_RX_FEAC_INTERRUPT_ENABLE_STATUS 11
+#define SBE_2T3E3_FRAMER_REG_T3_RX_LAPD_CONTROL 12
+#define SBE_2T3E3_FRAMER_REG_T3_RX_LAPD_STATUS 13
+#define SBE_2T3E3_FRAMER_REG_T3_TX_CONFIGURATION 16
+#define SBE_2T3E3_FRAMER_REG_T3_TX_FEAC_CONFIGURATION_STATUS 17
+#define SBE_2T3E3_FRAMER_REG_T3_TX_FEAC 18
+#define SBE_2T3E3_FRAMER_REG_T3_TX_LAPD_CONFIGURATION 19
+#define SBE_2T3E3_FRAMER_REG_T3_TX_LAPD_STATUS 20
+#define SBE_2T3E3_FRAMER_REG_T3_TX_MBIT_MASK 21
+#define SBE_2T3E3_FRAMER_REG_T3_TX_FBIT_MASK 22
+#define SBE_2T3E3_FRAMER_REG_T3_TX_FBIT_MASK_2 23
+#define SBE_2T3E3_FRAMER_REG_T3_TX_FBIT_MASK_3 24
+
+/* E3 */
+#define SBE_2T3E3_FRAMER_REG_E3_RX_CONFIGURATION_STATUS_1 4
+#define SBE_2T3E3_FRAMER_REG_E3_RX_CONFIGURATION_STATUS_2 5
+#define SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_ENABLE_1 6
+#define SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_ENABLE_2 7
+#define SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_STATUS_1 8
+#define SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_STATUS_2 9
+#define SBE_2T3E3_FRAMER_REG_E3_RX_LAPD_CONTROL 12
+#define SBE_2T3E3_FRAMER_REG_E3_RX_LAPD_STATUS 13
+#define SBE_2T3E3_FRAMER_REG_E3_RX_NR_BYTE 14
+#define SBE_2T3E3_FRAMER_REG_E3_RX_SERVICE_BITS 14
+#define SBE_2T3E3_FRAMER_REG_E3_RX_GC_BYTE 15
+#define SBE_2T3E3_FRAMER_REG_E3_TX_CONFIGURATION 16
+#define SBE_2T3E3_FRAMER_REG_E3_TX_LAPD_CONFIGURATION 19
+#define SBE_2T3E3_FRAMER_REG_E3_TX_LAPD_STATUS 19
+#define SBE_2T3E3_FRAMER_REG_E3_TX_GC_BYTE 21
+#define SBE_2T3E3_FRAMER_REG_E3_TX_SERVICE_BITS 21
+#define SBE_2T3E3_FRAMER_REG_E3_TX_MA_BYTE 22
+#define SBE_2T3E3_FRAMER_REG_E3_TX_NR_BYTE 23
+#define SBE_2T3E3_FRAMER_REG_E3_TX_FA1_ERROR_MASK 25
+#define SBE_2T3E3_FRAMER_REG_E3_TX_FAS_ERROR_MASK_UPPER 25
+#define SBE_2T3E3_FRAMER_REG_E3_TX_FA2_ERROR_MASK 26
+#define SBE_2T3E3_FRAMER_REG_E3_TX_FAS_ERROR_MASK_LOWER 26
+#define SBE_2T3E3_FRAMER_REG_E3_TX_BIP8_MASK 27
+#define SBE_2T3E3_FRAMER_REG_E3_TX_BIP4_MASK 27
+
+#define SBE_2T3E3_FRAMER_REG_MAX 48
+
+/**********/
+
+/* OPERATING_MODE */
+#define SBE_2T3E3_FRAMER_VAL_LOCAL_LOOPBACK_MODE 0x80
+#define SBE_2T3E3_FRAMER_VAL_T3_E3_SELECT 0x40
+#define SBE_2T3E3_FRAMER_VAL_INTERNAL_LOS_ENABLE 0x20
+#define SBE_2T3E3_FRAMER_VAL_RESET 0x10
+#define SBE_2T3E3_FRAMER_VAL_INTERRUPT_ENABLE_RESET 0x08
+#define SBE_2T3E3_FRAMER_VAL_FRAME_FORMAT_SELECT 0x04
+#define SBE_2T3E3_FRAMER_VAL_TIMING_ASYNCH_TXINCLK 0x03
+#define SBE_2T3E3_FRAMER_VAL_E3_G751 0x00
+#define SBE_2T3E3_FRAMER_VAL_E3_G832 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_CBIT 0x40
+#define SBE_2T3E3_FRAMER_VAL_T3_M13 0x44
+#define SBE_2T3E3_FRAMER_VAL_LOOPBACK_ON 0x80
+#define SBE_2T3E3_FRAMER_VAL_LOOPBACK_OFF 0x00
+
+/* IO_CONTROL */
+#define SBE_2T3E3_FRAMER_VAL_DISABLE_TX_LOSS_OF_CLOCK 0x80
+#define SBE_2T3E3_FRAMER_VAL_LOSS_OF_CLOCK_STATUS 0x40
+#define SBE_2T3E3_FRAMER_VAL_DISABLE_RX_LOSS_OF_CLOCK 0x20
+#define SBE_2T3E3_FRAMER_VAL_AMI_LINE_CODE 0x10
+#define SBE_2T3E3_FRAMER_VAL_UNIPOLAR 0x08
+#define SBE_2T3E3_FRAMER_VAL_TX_LINE_CLOCK_INVERT 0x04
+#define SBE_2T3E3_FRAMER_VAL_RX_LINE_CLOCK_INVERT 0x02
+#define SBE_2T3E3_FRAMER_VAL_REFRAME 0x01
+
+/* BLOCK_INTERRUPT_ENABLE */
+#define SBE_2T3E3_FRAMER_VAL_RX_INTERRUPT_ENABLE 0x80
+#define SBE_2T3E3_FRAMER_VAL_TX_INTERRUPT_ENABLE 0x02
+#define SBE_2T3E3_FRAMER_VAL_ONE_SECOND_INTERRUPT_ENABLE 0x01
+
+/* BLOCK_INTERRUPT_STATUS */
+#define SBE_2T3E3_FRAMER_VAL_RX_INTERRUPT_STATUS 0x80
+#define SBE_2T3E3_FRAMER_VAL_TX_INTERRUPT_STATUS 0x02
+#define SBE_2T3E3_FRAMER_VAL_ONE_SECOND_INTERRUPT_STATUS 0x01
+
+/**********/
+
+/* T3_RX_CONFIGURATION_STATUS */
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_AIS 0x80
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_LOS 0x40
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_IDLE 0x20
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_OOF 0x10
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FRAMING_ON_PARITY 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_F_SYNC_ALGO 0x02
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_M_SYNC_ALGO 0x01
+
+/* T3_RX_STATUS */
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FERF 0x10
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_AIC 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FEBE 0x07
+
+/* T3_RX_INTERRUPT_ENABLE */
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_CP_BIT_ERROR_INTERRUPT_ENABLE 0x80
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_LOS_INTERRUPT_ENABLE 0x40
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_AIS_INTERRUPT_ENABLE 0x20
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_IDLE_INTERRUPT_ENABLE 0x10
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FERF_INTERRUPT_ENABLE 0x08
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_AIC_INTERRUPT_ENABLE 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_OOF_INTERRUPT_ENABLE 0x02
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_P_BIT_INTERRUPT_ENABLE 0x01
+
+/* T3_RX_INTERRUPT_STATUS */
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_CP_BIT_ERROR_INTERRUPT_STATUS 0x80
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_LOS_INTERRUPT_STATUS 0x40
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_AIS_INTERRUPT_STATUS 0x20
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_IDLE_INTERRUPT_STATUS 0x10
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FERF_INTERRUPT_STATUS 0x08
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_AIC_INTERRUPT_STATUS 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_OOF_INTERRUPT_STATUS 0x02
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_P_BIT_INTERRUPT_STATUS 0x01
+
+/* T3_RX_FEAC_INTERRUPT_ENABLE_STATUS */
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FEAC_VALID 0x10
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FEAC_REMOVE_INTERRUPT_ENABLE 0x08
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FEAC_REMOVE_INTERRUPT_STATUS 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FEAC_VALID_INTERRUPT_ENABLE 0x02
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FEAC_VALID_INTERRUPT_STATUS 0x01
+
+/* T3_RX_LAPD_CONTROL */
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_LAPD_ENABLE 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_LAPD_INTERRUPT_ENABLE 0x02
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_LAPD_INTERRUPT_STATUS 0x01
+
+/* T3_RX_LAPD_STATUS */
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_ABORT 0x40
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_LAPD_TYPE 0x30
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_CR_TYPE 0x08
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FCS_ERROR 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_END_OF_MESSAGE 0x02
+#define SBE_2T3E3_FRAMER_VAL_T3_RX_FLAG_PRESENT 0x01
+
+/* T3_TX_CONFIGURATION */
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_YELLOW_ALARM 0x80
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_X_BIT 0x40
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_IDLE 0x20
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_AIS 0x10
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_LOS 0x08
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_FERF_ON_LOS 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_FERF_ON_OOF 0x02
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_FERF_ON_AIS 0x01
+
+/* T3_TX_FEAC_CONFIGURATION_STATUS */
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_FEAC_INTERRUPT_ENABLE 0x10
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_FEAC_INTERRUPT_STATUS 0x08
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_FEAC_ENABLE 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_FEAC_GO 0x02
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_FEAC_BUSY 0x01
+
+/* T3_TX_LAPD_STATUS */
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_DL_START 0x08
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_DL_BUSY 0x04
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_LAPD_INTERRUPT_ENABLE 0x02
+#define SBE_2T3E3_FRAMER_VAL_T3_TX_LAPD_INTERRUPT_STATUS 0x01
+
+/**********/
+
+/* E3_RX_CONFIGURATION_STATUS_1 */
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_PAYLOAD_TYPE 0xe0
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_FERF_ALGO 0x10
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_T_MARK_ALGO 0x08
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_PAYLOAD_EXPECTED 0x07
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_BIP4 0x01
+
+/* E3_RX_CONFIGURATION_STATUS_2 */
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LOF_ALGO 0x80
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LOF 0x40
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_OOF 0x20
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LOS 0x10
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_AIS 0x08
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_PAYLOAD_UNSTABLE 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_T_MARK 0x02
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_FERF 0x01
+
+/* E3_RX_INTERRUPT_ENABLE_1 */
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_COFA_INTERRUPT_ENABLE 0x10
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_OOF_INTERRUPT_ENABLE 0x08
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LOF_INTERRUPT_ENABLE 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LOS_INTERRUPT_ENABLE 0x02
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_AIS_INTERRUPT_ENABLE 0x01
+
+/* E3_RX_INTERRUPT_ENABLE_2 */
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_TTB_CHANGE_INTERRUPT_ENABLE 0x40
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_FEBE_INTERRUPT_ENABLE 0x10
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_FERF_INTERRUPT_ENABLE 0x08
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_BIP8_ERROR_INTERRUPT_ENABLE 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_BIP4_ERROR_INTERRUPT_ENABLE 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_FRAMING_BYTE_ERROR_INTERRUPT_ENABLE 0x02
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_PAYLOAD_MISMATCH_INTERRUPT_ENABLE 0x01
+
+/* E3_RX_INTERRUPT_STATUS_1 */
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_COFA_INTERRUPT_STATUS 0x10
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_OOF_INTERRUPT_STATUS 0x08
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LOF_INTERRUPT_STATUS 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LOS_INTERRUPT_STATUS 0x02
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_AIS_INTERRUPT_STATUS 0x01
+
+/* E3_RX_INTERRUPT_STATUS_2 */
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_TTB_CHANGE_INTERRUPT_STATUS 0x40
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_FEBE_INTERRUPT_STATUS 0x10
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_FERF_INTERRUPT_STATUS 0x08
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_BIP8_ERROR_INTERRUPT_STATUS 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_BIP4_ERROR_INTERRUPT_STATUS 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_FRAMING_BYTE_ERROR_INTERRUPT_STATUS 0x02
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_PAYLOAD_MISMATCH_INTERRUPT_STATUS 0x01
+
+/* E3_RX_LAPD_CONTROL */
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_DL_FROM_NR 0x08
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LAPD_ENABLE 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LAPD_INTERRUPT_ENABLE 0x02
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LAPD_INTERRUPT_STATUS 0x01
+
+/* E3_RX_LAPD_STATUS */
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_ABORT 0x40
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_LAPD_TYPE 0x30
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_CR_TYPE 0x08
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_FCS_ERROR 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_END_OF_MESSAGE 0x02
+#define SBE_2T3E3_FRAMER_VAL_E3_RX_FLAG_PRESENT 0x01
+
+/* E3_TX_CONFIGURATION */
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_BIP4_ENABLE 0x80
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_A_SOURCE_SELECT 0x60
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_DL_IN_NR 0x10
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_N_SOURCE_SELECT 0x18
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_AIS_ENABLE 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_LOS_ENABLE 0x02
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_MA_RX 0x01
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_FAS_SOURCE_SELECT 0x01
+
+/* E3_TX_LAPD_CONFIGURATION */
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_AUTO_RETRANSMIT 0x08
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_LAPD_MESSAGE_LENGTH 0x02
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_LAPD_ENABLE 0x01
+
+/* E3_TX_LAPD_STATUS_INTERRUPT */
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_DL_START 0x08
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_DL_BUSY 0x04
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_LAPD_INTERRUPT_ENABLE 0x02
+#define SBE_2T3E3_FRAMER_VAL_E3_TX_LAPD_INTERRUPT_STATUS 0x01
+
+
+
+
+
+
+/**************************************************************
+ * LIU
+ **************************************************************/
+
+/* reg_map indexes */
+#define SBE_2T3E3_LIU_REG_REG0 0
+#define SBE_2T3E3_LIU_REG_REG1 1
+#define SBE_2T3E3_LIU_REG_REG2 2
+#define SBE_2T3E3_LIU_REG_REG3 3
+#define SBE_2T3E3_LIU_REG_REG4 4
+
+#define SBE_2T3E3_LIU_REG_MAX 5
+
+/**********/
+
+/* REG0 */
+#define SBE_2T3E3_LIU_VAL_RECEIVE_LOSS_OF_LOCK_STATUS 0x10
+#define SBE_2T3E3_LIU_VAL_RECEIVE_LOSS_OF_SIGNAL_STATUS 0x08
+#define SBE_2T3E3_LIU_VAL_ANALOG_LOSS_OF_SIGNAL_STATUS 0x04
+#define SBE_2T3E3_LIU_VAL_DIGITAL_LOSS_OF_SIGNAL_STATUS 0x02
+#define SBE_2T3E3_LIU_VAL_DMO_STATUS 0x01
+
+/* REG1 */
+#define SBE_2T3E3_LIU_VAL_TRANSMITTER_OFF 0x10
+#define SBE_2T3E3_LIU_VAL_TRANSMIT_ALL_ONES 0x08
+#define SBE_2T3E3_LIU_VAL_TRANSMIT_CLOCK_INVERT 0x04
+#define SBE_2T3E3_LIU_VAL_TRANSMIT_LEVEL_SELECT 0x02
+#define SBE_2T3E3_LIU_VAL_TRANSMIT_BINARY_DATA 0x01
+
+/* REG2 */
+#define SBE_2T3E3_LIU_VAL_DECODER_DISABLE 0x10
+#define SBE_2T3E3_LIU_VAL_ENCODER_DISABLE 0x08
+#define SBE_2T3E3_LIU_VAL_ANALOG_LOSS_OF_SIGNAL_DISABLE 0x04
+#define SBE_2T3E3_LIU_VAL_DIGITAL_LOSS_OF_SIGNAL_DISABLE 0x02
+#define SBE_2T3E3_LIU_VAL_RECEIVE_EQUALIZATION_DISABLE 0x01
+
+/* REG3 */
+#define SBE_2T3E3_LIU_VAL_RECEIVE_BINARY_DATA 0x10
+#define SBE_2T3E3_LIU_VAL_RECOVERED_DATA_MUTING 0x08
+#define SBE_2T3E3_LIU_VAL_RECEIVE_CLOCK_OUTPUT_2 0x04
+#define SBE_2T3E3_LIU_VAL_INVERT_RECEIVE_CLOCK_2 0x02
+#define SBE_2T3E3_LIU_VAL_INVERT_RECEIVE_CLOCK_1 0x01
+
+/* REG4 */
+#define SBE_2T3E3_LIU_VAL_T3_MODE_SELECT 0x00
+#define SBE_2T3E3_LIU_VAL_E3_MODE_SELECT 0x04
+#define SBE_2T3E3_LIU_VAL_LOCAL_LOOPBACK 0x02
+#define SBE_2T3E3_LIU_VAL_REMOTE_LOOPBACK 0x01
+#define SBE_2T3E3_LIU_VAL_LOOPBACK_OFF 0x00
+#define SBE_2T3E3_LIU_VAL_LOOPBACK_REMOTE 0x01
+#define SBE_2T3E3_LIU_VAL_LOOPBACK_ANALOG 0x02
+#define SBE_2T3E3_LIU_VAL_LOOPBACK_DIGITAL 0x03
+
+/**********************************************************************
+ *
+ * descriptor list and data buffer
+ *
+ **********************************************************************/
+typedef struct {
+ u32 rdes0;
+ u32 rdes1;
+ u32 rdes2;
+ u32 rdes3;
+} t3e3_rx_desc_t;
+
+#define SBE_2T3E3_RX_DESC_RING_SIZE 64
+
+/* RDES0 */
+#define SBE_2T3E3_RX_DESC_21143_OWN 0X80000000
+#define SBE_2T3E3_RX_DESC_FRAME_LENGTH 0x3fff0000
+#define SBE_2T3E3_RX_DESC_FRAME_LENGTH_SHIFT 16
+#define SBE_2T3E3_RX_DESC_ERROR_SUMMARY 0x00008000
+#define SBE_2T3E3_RX_DESC_DESC_ERROR 0x00004000
+#define SBE_2T3E3_RX_DESC_DATA_TYPE 0x00003000
+#define SBE_2T3E3_RX_DESC_RUNT_FRAME 0x00000800
+#define SBE_2T3E3_RX_DESC_FIRST_DESC 0x00000200
+#define SBE_2T3E3_RX_DESC_LAST_DESC 0x00000100
+#define SBE_2T3E3_RX_DESC_FRAME_TOO_LONG 0x00000080
+#define SBE_2T3E3_RX_DESC_COLLISION_SEEN 0x00000040
+#define SBE_2T3E3_RX_DESC_FRAME_TYPE 0x00000020
+#define SBE_2T3E3_RX_DESC_RECEIVE_WATCHDOG 0x00000010
+#define SBE_2T3E3_RX_DESC_MII_ERROR 0x00000008
+#define SBE_2T3E3_RX_DESC_DRIBBLING_BIT 0x00000004
+#define SBE_2T3E3_RX_DESC_CRC_ERROR 0x00000002
+
+/* RDES1 */
+#define SBE_2T3E3_RX_DESC_END_OF_RING 0x02000000
+#define SBE_2T3E3_RX_DESC_SECOND_ADDRESS_CHAINED 0x01000000
+#define SBE_2T3E3_RX_DESC_BUFFER_2_SIZE 0x003ff800
+#define SBE_2T3E3_RX_DESC_BUFFER_1_SIZE 0x000007ff
+
+/*********************/
+
+typedef struct {
+ u32 tdes0;
+ u32 tdes1;
+ u32 tdes2;
+ u32 tdes3;
+} t3e3_tx_desc_t;
+
+#define SBE_2T3E3_TX_DESC_RING_SIZE 256
+
+/* TDES0 */
+#define SBE_2T3E3_TX_DESC_21143_OWN 0x80000000
+#define SBE_2T3E3_TX_DESC_ERROR_SUMMARY 0x00008000
+#define SBE_2T3E3_TX_DESC_TRANSMIT_JABBER_TIMEOUT 0x00004000
+#define SBE_2T3E3_TX_DESC_LOSS_OF_CARRIER 0x00000800
+#define SBE_2T3E3_TX_DESC_NO_CARRIER 0x00000400
+#define SBE_2T3E3_TX_DESC_LINK_FAIL_REPORT 0x00000004
+#define SBE_2T3E3_TX_DESC_UNDERFLOW_ERROR 0x00000002
+#define SBE_2T3E3_TX_DESC_DEFFERED 0x00000001
+
+/* TDES1 */
+#define SBE_2T3E3_TX_DESC_INTERRUPT_ON_COMPLETION 0x80000000
+#define SBE_2T3E3_TX_DESC_LAST_SEGMENT 0x40000000
+#define SBE_2T3E3_TX_DESC_FIRST_SEGMENT 0x20000000
+#define SBE_2T3E3_TX_DESC_CRC_DISABLE 0x04000000
+#define SBE_2T3E3_TX_DESC_END_OF_RING 0x02000000
+#define SBE_2T3E3_TX_DESC_SECOND_ADDRESS_CHAINED 0x01000000
+#define SBE_2T3E3_TX_DESC_DISABLE_PADDING 0x00800000
+#define SBE_2T3E3_TX_DESC_BUFFER_2_SIZE 0x003ff800
+#define SBE_2T3E3_TX_DESC_BUFFER_1_SIZE 0x000007ff
+
+
+#define SBE_2T3E3_MTU 1600
+#define SBE_2T3E3_CRC16_LENGTH 2
+#define SBE_2T3E3_CRC32_LENGTH 4
+
+#define MCLBYTES (SBE_2T3E3_MTU + 128)
+
+struct channel {
+ struct pci_dev *pdev;
+ struct net_device *dev;
+ struct card *card;
+ unsigned long addr; /* DECchip */
+
+ int leds;
+
+ /* pci specific */
+ struct {
+ u32 slot; /* should be 0 or 1 */
+ u32 command;
+ u8 cache_size;
+ } h;
+
+ /* statistics */
+ t3e3_stats_t s;
+
+ /* running */
+ struct {
+ u32 flags;
+ } r;
+
+ /* parameters */
+ t3e3_param_t p;
+
+ u32 liu_regs[SBE_2T3E3_LIU_REG_MAX]; /* LIU registers */
+ u32 framer_regs[SBE_2T3E3_FRAMER_REG_MAX]; /* Framer registers */
+
+ /* Ethernet Controller */
+ struct {
+ u_int16_t card_serial_number[3];
+
+ u32 reg[SBE_2T3E3_21143_REG_MAX]; /* registers i.e. CSR */
+
+ u32 interrupt_enable_mask;
+
+ /* receive chain/ring */
+ t3e3_rx_desc_t *rx_ring;
+ struct sk_buff *rx_data[SBE_2T3E3_RX_DESC_RING_SIZE];
+ u32 rx_ring_current_read;
+
+ /* transmit chain/ring */
+ t3e3_tx_desc_t *tx_ring;
+ struct sk_buff *tx_data[SBE_2T3E3_TX_DESC_RING_SIZE];
+ u32 tx_ring_current_read;
+ u32 tx_ring_current_write;
+ int tx_full;
+ int tx_free_cnt;
+ spinlock_t tx_lock;
+ } ether;
+
+ int32_t interrupt_active;
+ int32_t rcv_count;
+};
+
+struct card {
+ spinlock_t bootrom_lock;
+ unsigned long bootrom_addr;
+ struct timer_list timer; /* for updating LEDs */
+ struct channel channels[0];
+};
+
+#define SBE_2T3E3_FLAG_NETWORK_UP 0x00000001
+#define SBE_2T3E3_FLAG_NO_ERROR_MESSAGES 0x00000002
+
+extern const u32 cpld_reg_map[][2];
+extern const u32 cpld_val_map[][2];
+extern const u32 t3e3_framer_reg_map[];
+extern const u32 t3e3_liu_reg_map[];
+
+void t3e3_init(struct channel *);
+void t3e3_if_up(struct channel *);
+void t3e3_if_down(struct channel *);
+int t3e3_if_start_xmit(struct sk_buff *skb, struct net_device *dev);
+void t3e3_if_config(struct channel *, u32, char *,
+ t3e3_resp_t *, int *);
+void t3e3_set_frame_type(struct channel *, u32);
+u32 t3e3_eeprom_read_word(struct channel *, u32);
+void t3e3_read_card_serial_number(struct channel *);
+
+/* interrupt handlers */
+irqreturn_t t3e3_intr(int irq, void *dev_instance);
+void dc_intr(struct channel *);
+void dc_intr_rx(struct channel *);
+void dc_intr_tx(struct channel *);
+void dc_intr_tx_underflow(struct channel *);
+void exar7250_intr(struct channel *);
+void exar7250_E3_intr(struct channel *, u32);
+void exar7250_T3_intr(struct channel *, u32);
+
+/* Ethernet controller */
+u32 bootrom_read(struct channel *, u32);
+void bootrom_write(struct channel *, u32, u32);
+void dc_init(struct channel *);
+void dc_start(struct channel *);
+void dc_stop(struct channel *);
+void dc_start_intr(struct channel *);
+void dc_stop_intr(struct channel *);
+void dc_reset(struct channel *);
+void dc_restart(struct channel *);
+void dc_receiver_onoff(struct channel *, u32);
+void dc_transmitter_onoff(struct channel *, u32);
+void dc_set_loopback(struct channel *, u32);
+u32 dc_init_descriptor_list(struct channel *);
+void dc_clear_descriptor_list(struct channel *);
+void dc_drop_descriptor_list(struct channel *);
+void dc_set_output_port(struct channel *);
+void t3e3_sc_init(struct channel *);
+
+/* CPLD */
+void cpld_init(struct channel *sc);
+u32 cpld_read(struct channel *sc, u32 reg);
+void cpld_set_crc(struct channel *, u32);
+void cpld_start_intr(struct channel *);
+void cpld_stop_intr(struct channel *);
+#if 0
+void cpld_led_onoff(struct channel *, u32, u32, u32, u32);
+#endif
+void cpld_set_clock(struct channel *sc, u32 mode);
+void cpld_set_scrambler(struct channel *, u32);
+void cpld_select_panel(struct channel *, u32);
+void cpld_set_frame_mode(struct channel *, u32);
+void cpld_set_frame_type(struct channel *, u32);
+void cpld_set_pad_count(struct channel *, u32);
+void cpld_set_fractional_mode(struct channel *, u32, u32, u32);
+void cpld_LOS_update(struct channel *);
+
+/* Framer */
+extern u32 exar7250_read(struct channel *, u32);
+extern void exar7250_write(struct channel *, u32, u32);
+void exar7250_init(struct channel *);
+void exar7250_start_intr(struct channel *, u32);
+void exar7250_stop_intr(struct channel *, u32);
+void exar7250_set_frame_type(struct channel *, u32);
+void exar7250_set_loopback(struct channel *, u32);
+void exar7250_unipolar_onoff(struct channel *, u32);
+
+/* LIU */
+u32 exar7300_read(struct channel *, u32);
+void exar7300_write(struct channel *, u32, u32);
+void exar7300_init(struct channel *);
+void exar7300_line_build_out_onoff(struct channel *, u32);
+void exar7300_set_frame_type(struct channel *, u32);
+void exar7300_set_loopback(struct channel *, u32);
+void exar7300_transmit_all_ones_onoff(struct channel *, u32);
+void exar7300_receive_equalization_onoff(struct channel *, u32);
+void exar7300_unipolar_onoff(struct channel *, u32);
+
+void update_led(struct channel *, int);
+int setup_device(struct net_device *dev, struct channel *sc);
+
+static inline int has_two_ports(struct pci_dev *pdev)
+{
+ return pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_2T3E3_P0;
+}
+
+#define dev_to_priv(dev) (*(struct channel **) ((hdlc_device*)(dev) + 1))
+
+static inline u32 dc_read(unsigned long addr, u32 reg)
+{
+ return inl(addr + (reg << 3));
+}
+
+static inline void dc_write(unsigned long addr, u32 reg, u32 val)
+{
+ outl(val, addr + (reg << 3));
+}
+
+static inline void dc_set_bits(unsigned long addr, u32 reg, u32 bits)
+{
+ dc_write(addr, reg, dc_read(addr, reg) | bits);
+}
+
+static inline void dc_clear_bits(unsigned long addr, u32 reg, u32 bits)
+{
+ dc_write(addr, reg, dc_read(addr, reg) & ~bits);
+}
+
+#define CPLD_MAP_REG(reg, sc) (cpld_reg_map[(reg)][(sc)->h.slot])
+
+static inline void cpld_write(struct channel *channel, unsigned reg, u32 val)
+{
+ unsigned long flags;
+ spin_lock_irqsave(&channel->card->bootrom_lock, flags);
+ bootrom_write(channel, CPLD_MAP_REG(reg, channel), val);
+ spin_unlock_irqrestore(&channel->card->bootrom_lock, flags);
+}
+
+#define exar7250_set_bit(sc, reg, bit) \
+ exar7250_write((sc), (reg), \
+ exar7250_read(sc, reg) | (bit))
+
+#define exar7250_clear_bit(sc, reg, bit) \
+ exar7250_write((sc), (reg), \
+ exar7250_read(sc, reg) & ~(bit))
+
+#define exar7300_set_bit(sc, reg, bit) \
+ exar7300_write((sc), (reg), \
+ exar7300_read(sc, reg) | (bit))
+
+#define exar7300_clear_bit(sc, reg, bit) \
+ exar7300_write((sc), (reg), \
+ exar7300_read(sc, reg) & ~(bit))
+
+
+#endif /* T3E3_H */
--- /dev/null
+config SBE_2T3E3
+ tristate "SBE wanPMC-2T3E3 support"
+ depends on HDLC && PCI
+ help
+ Driver for wanPMC-2T3E3 cards by SBE Inc.
+
+ If you have such a card, say Y here and see
+ <http://www.kernel.org/pub/linux/utils/net/hdlc/>.
+
+ To compile this as a module, choose M here: the
+ module will be called sbe-2t3e3.
+
+ If unsure, say N.
--- /dev/null
+obj-$(CONFIG_SBE_2T3E3) += sbe-2t3e3.o
+
+sbe-2t3e3-objs := module.o netdev.o maps.o \
+ main.o cpld.o intr.o ctrl.o io.o dc.o exar7250.o exar7300.o
--- /dev/null
+TODO:
+ - additional cleaning and tests
+ - wait for the new configuration interface in generic HDLC layer and
+ when available, convert the driver to it
+
+Please send patches to Krzysztof Halasa <khc@pm.waw.pl>.
\ No newline at end of file
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include <linux/delay.h>
+#include "2t3e3.h"
+#include "ctrl.h"
+
+#define bootrom_set_bit(sc, reg, bit) \
+ bootrom_write((sc), (reg), \
+ bootrom_read((sc), (reg)) | (bit))
+
+#define bootrom_clear_bit(sc, reg, bit) \
+ bootrom_write((sc), (reg), \
+ bootrom_read((sc), (reg)) & ~(bit))
+
+static inline void cpld_set_bit(struct channel *channel, unsigned reg, u32 bit)
+{
+ unsigned long flags;
+ spin_lock_irqsave(&channel->card->bootrom_lock, flags);
+ bootrom_set_bit(channel, CPLD_MAP_REG(reg, channel), bit);
+ spin_unlock_irqrestore(&channel->card->bootrom_lock, flags);
+}
+
+static inline void cpld_clear_bit(struct channel *channel, unsigned reg, u32 bit)
+{
+ unsigned long flags;
+ spin_lock_irqsave(&channel->card->bootrom_lock, flags);
+ bootrom_clear_bit(channel, CPLD_MAP_REG(reg, channel), bit);
+ spin_unlock_irqrestore(&channel->card->bootrom_lock, flags);
+}
+
+void cpld_init(struct channel *sc)
+{
+ u32 val;
+#if 0
+ /* reset LIU and Framer */
+ val = cpld_val_map[SBE_2T3E3_CPLD_VAL_LIU_FRAMER_RESET][sc->h.slot];
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_STATIC_RESET, val);
+ udelay(10000); /* TODO - how long? */
+ val = 0;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_STATIC_RESET, val);
+#endif
+
+ /* PCRA */
+ val = SBE_2T3E3_CPLD_VAL_CRC32 |
+ cpld_val_map[SBE_2T3E3_CPLD_VAL_LOOP_TIMING_SOURCE][sc->h.slot];
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PCRA, val);
+
+ /* PCRB */
+ val = 0;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PCRB, val);
+
+ /* PCRC */
+ val = 0;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PCRC, val);
+
+ /* PBWF */
+ val = 0;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PBWF, val);
+
+ /* PBWL */
+ val = 0;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PBWL, val);
+
+ /* PLTR */
+ val = SBE_2T3E3_CPLD_VAL_LCV_COUNTER;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PLTR, val);
+ udelay(1000);
+
+ /* PLCR */
+ val = 0;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PLCR, val);
+ udelay(1000);
+
+ /* PPFR */
+ val = 0x55;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PPFR, val);
+ /* TODO: this doesn't work!!! */
+
+ /* SERIAL_CHIP_SELECT */
+ val = 0;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_SERIAL_CHIP_SELECT, val);
+
+ /* PICSR */
+ val = SBE_2T3E3_CPLD_VAL_DMO_SIGNAL_DETECTED |
+ SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_LOCK_DETECTED |
+ SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_SIGNAL_DETECTED;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PICSR, val);
+
+ cpld_start_intr(sc);
+
+ udelay(1000);
+}
+
+void cpld_start_intr(struct channel *sc)
+{
+ u32 val;
+
+ /* PIER */
+ val = SBE_2T3E3_CPLD_VAL_INTERRUPT_FROM_ETHERNET_ENABLE |
+ SBE_2T3E3_CPLD_VAL_INTERRUPT_FROM_FRAMER_ENABLE;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PIER, val);
+#if 0
+ /*
+ do you want to hang up your computer?
+ ENABLE REST OF INTERRUPTS !!!
+ you have been warned :).
+ */
+#endif
+}
+
+void cpld_stop_intr(struct channel *sc)
+{
+ u32 val;
+
+ /* PIER */
+ val = 0;
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PIER, val);
+}
+
+void cpld_set_frame_mode(struct channel *sc, u32 mode)
+{
+ if (sc->p.frame_mode == mode)
+ return;
+
+ switch (mode) {
+ case SBE_2T3E3_FRAME_MODE_HDLC:
+ cpld_clear_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_TRANSPARENT_MODE |
+ SBE_2T3E3_CPLD_VAL_RAW_MODE);
+ exar7250_unipolar_onoff(sc, SBE_2T3E3_OFF);
+ exar7300_unipolar_onoff(sc, SBE_2T3E3_OFF);
+ break;
+ case SBE_2T3E3_FRAME_MODE_TRANSPARENT:
+ cpld_clear_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_RAW_MODE);
+ cpld_set_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_TRANSPARENT_MODE);
+ exar7250_unipolar_onoff(sc, SBE_2T3E3_OFF);
+ exar7300_unipolar_onoff(sc, SBE_2T3E3_OFF);
+ break;
+ case SBE_2T3E3_FRAME_MODE_RAW:
+ cpld_set_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_RAW_MODE);
+ exar7250_unipolar_onoff(sc, SBE_2T3E3_ON);
+ exar7300_unipolar_onoff(sc, SBE_2T3E3_ON);
+ break;
+ default:
+ return;
+ }
+
+ sc->p.frame_mode = mode;
+}
+
+/* set rate of the local clock */
+void cpld_set_frame_type(struct channel *sc, u32 type)
+{
+ switch (type) {
+ case SBE_2T3E3_FRAME_TYPE_E3_G751:
+ case SBE_2T3E3_FRAME_TYPE_E3_G832:
+ cpld_set_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_LOCAL_CLOCK_E3);
+ break;
+ case SBE_2T3E3_FRAME_TYPE_T3_CBIT:
+ case SBE_2T3E3_FRAME_TYPE_T3_M13:
+ cpld_clear_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_LOCAL_CLOCK_E3);
+ break;
+ default:
+ return;
+ }
+}
+
+void cpld_set_scrambler(struct channel *sc, u32 mode)
+{
+ if (sc->p.scrambler == mode)
+ return;
+
+ switch (mode) {
+ case SBE_2T3E3_SCRAMBLER_OFF:
+ cpld_clear_bit(sc, SBE_2T3E3_CPLD_REG_PCRB,
+ SBE_2T3E3_CPLD_VAL_SCRAMBLER_ENABLE);
+ break;
+ case SBE_2T3E3_SCRAMBLER_LARSCOM:
+ cpld_clear_bit(sc, SBE_2T3E3_CPLD_REG_PCRB,
+ SBE_2T3E3_CPLD_VAL_SCRAMBLER_TYPE);
+ cpld_set_bit(sc, SBE_2T3E3_CPLD_REG_PCRB,
+ SBE_2T3E3_CPLD_VAL_SCRAMBLER_ENABLE);
+ break;
+ case SBE_2T3E3_SCRAMBLER_ADC_KENTROX_DIGITAL:
+ cpld_set_bit(sc, SBE_2T3E3_CPLD_REG_PCRB,
+ SBE_2T3E3_CPLD_VAL_SCRAMBLER_TYPE);
+ cpld_set_bit(sc, SBE_2T3E3_CPLD_REG_PCRB,
+ SBE_2T3E3_CPLD_VAL_SCRAMBLER_ENABLE);
+ break;
+ default:
+ return;
+ }
+
+ sc->p.scrambler = mode;
+}
+
+
+void cpld_set_crc(struct channel *sc, u32 crc)
+{
+ if (sc->p.crc == crc)
+ return;
+
+ switch (crc) {
+ case SBE_2T3E3_CRC_16:
+ cpld_clear_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_CRC32);
+ break;
+ case SBE_2T3E3_CRC_32:
+ cpld_set_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_CRC32);
+ break;
+ default:
+ return;
+ }
+
+ sc->p.crc = crc;
+}
+
+
+void cpld_select_panel(struct channel *sc, u32 panel)
+{
+ if (sc->p.panel == panel)
+ return;
+ switch (panel) {
+ case SBE_2T3E3_PANEL_FRONT:
+ cpld_clear_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_REAR_PANEL);
+ break;
+ case SBE_2T3E3_PANEL_REAR:
+ cpld_set_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_REAR_PANEL);
+ break;
+ default:
+ return;
+ }
+
+ udelay(100);
+
+ sc->p.panel = panel;
+}
+
+
+extern void cpld_set_clock(struct channel *sc, u32 mode)
+{
+ if (sc->p.clock_source == mode)
+ return;
+
+ switch (mode) {
+ case SBE_2T3E3_TIMING_LOCAL:
+ cpld_set_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_ALT);
+ break;
+ case SBE_2T3E3_TIMING_LOOP:
+ cpld_clear_bit(sc, SBE_2T3E3_CPLD_REG_PCRA,
+ SBE_2T3E3_CPLD_VAL_ALT);
+ break;
+ default:
+ return;
+ }
+
+ sc->p.clock_source = mode;
+}
+
+void cpld_set_pad_count(struct channel *sc, u32 count)
+{
+ u32 val;
+
+ if (sc->p.pad_count == count)
+ return;
+
+ switch (count) {
+ case SBE_2T3E3_PAD_COUNT_1:
+ val = SBE_2T3E3_CPLD_VAL_PAD_COUNT_1;
+ break;
+ case SBE_2T3E3_PAD_COUNT_2:
+ val = SBE_2T3E3_CPLD_VAL_PAD_COUNT_2;
+ break;
+ case SBE_2T3E3_PAD_COUNT_3:
+ val = SBE_2T3E3_CPLD_VAL_PAD_COUNT_3;
+ break;
+ case SBE_2T3E3_PAD_COUNT_4:
+ val = SBE_2T3E3_CPLD_VAL_PAD_COUNT_4;
+ break;
+ default:
+ return;
+ }
+
+ cpld_clear_bit(sc, SBE_2T3E3_CPLD_REG_PCRB,
+ SBE_2T3E3_CPLD_VAL_PAD_COUNT);
+ cpld_set_bit(sc, SBE_2T3E3_CPLD_REG_PCRB, val);
+ sc->p.pad_count = count;
+}
+
+void cpld_LOS_update(struct channel *sc)
+{
+ u_int8_t los;
+
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PICSR,
+ SBE_2T3E3_CPLD_VAL_DMO_SIGNAL_DETECTED |
+ SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_LOCK_DETECTED |
+ SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_SIGNAL_DETECTED);
+ los = cpld_read(sc, SBE_2T3E3_CPLD_REG_PICSR) &
+ SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_SIGNAL_DETECTED;
+
+ if (los != sc->s.LOS)
+ dev_info(&sc->pdev->dev, "SBE 2T3E3: LOS status: %s\n",
+ los ? "Loss of signal" : "Signal OK");
+ sc->s.LOS = los;
+}
+
+void cpld_set_fractional_mode(struct channel *sc, u32 mode,
+ u32 start, u32 stop)
+{
+ if (mode == SBE_2T3E3_FRACTIONAL_MODE_NONE) {
+ start = 0;
+ stop = 0;
+ }
+
+ if (sc->p.fractional_mode == mode && sc->p.bandwidth_start == start &&
+ sc->p.bandwidth_stop == stop)
+ return;
+
+ switch (mode) {
+ case SBE_2T3E3_FRACTIONAL_MODE_NONE:
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PCRC,
+ SBE_2T3E3_CPLD_VAL_FRACTIONAL_MODE_NONE);
+ break;
+ case SBE_2T3E3_FRACTIONAL_MODE_0:
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PCRC,
+ SBE_2T3E3_CPLD_VAL_FRACTIONAL_MODE_0);
+ break;
+ case SBE_2T3E3_FRACTIONAL_MODE_1:
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PCRC,
+ SBE_2T3E3_CPLD_VAL_FRACTIONAL_MODE_1);
+ break;
+ case SBE_2T3E3_FRACTIONAL_MODE_2:
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PCRC,
+ SBE_2T3E3_CPLD_VAL_FRACTIONAL_MODE_2);
+ break;
+ default:
+ printk(KERN_ERR "wrong mode in set_fractional_mode\n");
+ return;
+ }
+
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PBWF, start);
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_PBWL, stop);
+
+ sc->p.fractional_mode = mode;
+ sc->p.bandwidth_start = start;
+ sc->p.bandwidth_stop = stop;
+}
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include <linux/types.h>
+#include "2t3e3.h"
+#include "ctrl.h"
+
+void t3e3_set_frame_type(struct channel *sc, u32 mode)
+{
+ if (sc->p.frame_type == mode)
+ return;
+
+ if (sc->r.flags & SBE_2T3E3_FLAG_NETWORK_UP) {
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: changing frame type during active connection\n");
+ return;
+ }
+
+ exar7300_set_frame_type(sc, mode);
+ exar7250_set_frame_type(sc, mode);
+ cpld_set_frame_type(sc, mode);
+
+ sc->p.frame_type = mode;
+}
+
+void t3e3_set_loopback(struct channel *sc, u32 mode)
+{
+ u32 tx, rx;
+
+ if (sc->p.loopback == mode)
+ return;
+
+ tx = sc->p.transmitter_on;
+ rx = sc->p.receiver_on;
+ if (tx == SBE_2T3E3_ON)
+ dc_transmitter_onoff(sc, SBE_2T3E3_OFF);
+ if (rx == SBE_2T3E3_ON)
+ dc_receiver_onoff(sc, SBE_2T3E3_OFF);
+
+ /* stop current loopback if any exists */
+ switch (sc->p.loopback) {
+ case SBE_2T3E3_LOOPBACK_NONE:
+ break;
+ case SBE_2T3E3_LOOPBACK_ETHERNET:
+ dc_set_loopback(sc, SBE_2T3E3_21143_VAL_LOOPBACK_OFF);
+ break;
+ case SBE_2T3E3_LOOPBACK_FRAMER:
+ exar7250_set_loopback(sc, SBE_2T3E3_FRAMER_VAL_LOOPBACK_OFF);
+ break;
+ case SBE_2T3E3_LOOPBACK_LIU_DIGITAL:
+ case SBE_2T3E3_LOOPBACK_LIU_ANALOG:
+ case SBE_2T3E3_LOOPBACK_LIU_REMOTE:
+ exar7300_set_loopback(sc, SBE_2T3E3_LIU_VAL_LOOPBACK_OFF);
+ break;
+ default:
+ return;
+ }
+
+ switch (mode) {
+ case SBE_2T3E3_LOOPBACK_NONE:
+ break;
+ case SBE_2T3E3_LOOPBACK_ETHERNET:
+ dc_set_loopback(sc, SBE_2T3E3_21143_VAL_LOOPBACK_INTERNAL);
+ break;
+ case SBE_2T3E3_LOOPBACK_FRAMER:
+ exar7250_set_loopback(sc, SBE_2T3E3_FRAMER_VAL_LOOPBACK_ON);
+ break;
+ case SBE_2T3E3_LOOPBACK_LIU_DIGITAL:
+ exar7300_set_loopback(sc, SBE_2T3E3_LIU_VAL_LOOPBACK_DIGITAL);
+ break;
+ case SBE_2T3E3_LOOPBACK_LIU_ANALOG:
+ exar7300_set_loopback(sc, SBE_2T3E3_LIU_VAL_LOOPBACK_ANALOG);
+ break;
+ case SBE_2T3E3_LOOPBACK_LIU_REMOTE:
+ exar7300_set_loopback(sc, SBE_2T3E3_LIU_VAL_LOOPBACK_REMOTE);
+ break;
+ default:
+ return;
+ }
+
+ sc->p.loopback = mode;
+
+ if (tx == SBE_2T3E3_ON)
+ dc_transmitter_onoff(sc, SBE_2T3E3_ON);
+ if (rx == SBE_2T3E3_ON)
+ dc_receiver_onoff(sc, SBE_2T3E3_ON);
+}
+
+
+void t3e3_reg_read(struct channel *sc, u32 *reg, u32 *val)
+{
+ u32 i;
+
+ *val = 0;
+
+ switch (reg[0]) {
+ case SBE_2T3E3_CHIP_21143:
+ if (!(reg[1] & 7))
+ *val = dc_read(sc->addr, reg[1] / 8);
+ break;
+ case SBE_2T3E3_CHIP_CPLD:
+ for (i = 0; i < SBE_2T3E3_CPLD_REG_MAX; i++)
+ if (cpld_reg_map[i][sc->h.slot] == reg[1]) {
+ *val = cpld_read(sc, i);
+ break;
+ }
+ break;
+ case SBE_2T3E3_CHIP_FRAMER:
+ for (i = 0; i < SBE_2T3E3_FRAMER_REG_MAX; i++)
+ if (t3e3_framer_reg_map[i] == reg[1]) {
+ *val = exar7250_read(sc, i);
+ break;
+ }
+ break;
+ case SBE_2T3E3_CHIP_LIU:
+ for (i = 0; i < SBE_2T3E3_LIU_REG_MAX; i++)
+ if (t3e3_liu_reg_map[i] == reg[1]) {
+ *val = exar7300_read(sc, i);
+ break;
+ }
+ break;
+ default:
+ break;
+ }
+}
+
+void t3e3_reg_write(struct channel *sc, u32 *reg)
+{
+ u32 i;
+
+ switch (reg[0]) {
+ case SBE_2T3E3_CHIP_21143:
+ dc_write(sc->addr, reg[1], reg[2]);
+ break;
+ case SBE_2T3E3_CHIP_CPLD:
+ for (i = 0; i < SBE_2T3E3_CPLD_REG_MAX; i++)
+ if (cpld_reg_map[i][sc->h.slot] == reg[1]) {
+ cpld_write(sc, i, reg[2]);
+ break;
+ }
+ break;
+ case SBE_2T3E3_CHIP_FRAMER:
+ for (i = 0; i < SBE_2T3E3_FRAMER_REG_MAX; i++)
+ if (t3e3_framer_reg_map[i] == reg[1]) {
+ exar7250_write(sc, i, reg[2]);
+ break;
+ }
+ break;
+ case SBE_2T3E3_CHIP_LIU:
+ for (i = 0; i < SBE_2T3E3_LIU_REG_MAX; i++)
+ if (t3e3_liu_reg_map[i] == reg[1]) {
+ exar7300_write(sc, i, reg[2]);
+ break;
+ }
+ break;
+ }
+}
+
+void t3e3_port_get(struct channel *sc, t3e3_param_t *param)
+{
+ memcpy(param, &(sc->p), sizeof(t3e3_param_t));
+}
+
+void t3e3_port_set(struct channel *sc, t3e3_param_t *param)
+{
+ if (param->frame_mode != 0xff)
+ cpld_set_frame_mode(sc, param->frame_mode);
+
+ if (param->fractional_mode != 0xff)
+ cpld_set_fractional_mode(sc, param->fractional_mode,
+ param->bandwidth_start,
+ param->bandwidth_stop);
+
+ if (param->pad_count != 0xff)
+ cpld_set_pad_count(sc, param->pad_count);
+
+ if (param->crc != 0xff)
+ cpld_set_crc(sc, param->crc);
+
+ if (param->receiver_on != 0xff)
+ dc_receiver_onoff(sc, param->receiver_on);
+
+ if (param->transmitter_on != 0xff)
+ dc_transmitter_onoff(sc, param->transmitter_on);
+
+ if (param->frame_type != 0xff)
+ t3e3_set_frame_type(sc, param->frame_type);
+
+ if (param->panel != 0xff)
+ cpld_select_panel(sc, param->panel);
+
+ if (param->line_build_out != 0xff)
+ exar7300_line_build_out_onoff(sc, param->line_build_out);
+
+ if (param->receive_equalization != 0xff)
+ exar7300_receive_equalization_onoff(sc, param->receive_equalization);
+
+ if (param->transmit_all_ones != 0xff)
+ exar7300_transmit_all_ones_onoff(sc, param->transmit_all_ones);
+
+ if (param->loopback != 0xff)
+ t3e3_set_loopback(sc, param->loopback);
+
+ if (param->clock_source != 0xff)
+ cpld_set_clock(sc, param->clock_source);
+
+ if (param->scrambler != 0xff)
+ cpld_set_scrambler(sc, param->scrambler);
+}
+
+void t3e3_port_get_stats(struct channel *sc,
+ t3e3_stats_t *stats)
+{
+ u32 result;
+
+ sc->s.LOC = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_IO_CONTROL)
+ & SBE_2T3E3_FRAMER_VAL_LOSS_OF_CLOCK_STATUS ? 1 : 0;
+
+ switch (sc->p.frame_type) {
+ case SBE_2T3E3_FRAME_TYPE_E3_G751:
+ case SBE_2T3E3_FRAME_TYPE_E3_G832:
+ result = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_CONFIGURATION_STATUS_2);
+ sc->s.LOF = result & SBE_2T3E3_FRAMER_VAL_E3_RX_LOF ? 1 : 0;
+ sc->s.OOF = result & SBE_2T3E3_FRAMER_VAL_E3_RX_OOF ? 1 : 0;
+#if 0
+ sc->s.LOS = result & SBE_2T3E3_FRAMER_VAL_E3_RX_LOS ? 1 : 0;
+#else
+ cpld_LOS_update(sc);
+#endif
+ sc->s.AIS = result & SBE_2T3E3_FRAMER_VAL_E3_RX_AIS ? 1 : 0;
+ sc->s.FERF = result & SBE_2T3E3_FRAMER_VAL_E3_RX_FERF ? 1 : 0;
+ break;
+
+ case SBE_2T3E3_FRAME_TYPE_T3_CBIT:
+ case SBE_2T3E3_FRAME_TYPE_T3_M13:
+ result = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_CONFIGURATION_STATUS);
+ sc->s.AIS = result & SBE_2T3E3_FRAMER_VAL_T3_RX_AIS ? 1 : 0;
+#if 0
+ sc->s.LOS = result & SBE_2T3E3_FRAMER_VAL_T3_RX_LOS ? 1 : 0;
+#else
+ cpld_LOS_update(sc);
+#endif
+ sc->s.IDLE = result & SBE_2T3E3_FRAMER_VAL_T3_RX_IDLE ? 1 : 0;
+ sc->s.OOF = result & SBE_2T3E3_FRAMER_VAL_T3_RX_OOF ? 1 : 0;
+
+ result = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_STATUS);
+ sc->s.FERF = result & SBE_2T3E3_FRAMER_VAL_T3_RX_FERF ? 1 : 0;
+ sc->s.AIC = result & SBE_2T3E3_FRAMER_VAL_T3_RX_AIC ? 1 : 0;
+ sc->s.FEBE_code = result & SBE_2T3E3_FRAMER_VAL_T3_RX_FEBE;
+
+ sc->s.FEAC = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_FEAC);
+ break;
+
+ default:
+ break;
+ }
+
+ result = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_PMON_LCV_EVENT_COUNT_MSB) << 8;
+ result += exar7250_read(sc, SBE_2T3E3_FRAMER_REG_PMON_HOLDING_REGISTER);
+ sc->s.LCV += result;
+
+ result = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_PMON_FRAMING_BIT_ERROR_EVENT_COUNT_MSB) << 8;
+ result += exar7250_read(sc, SBE_2T3E3_FRAMER_REG_PMON_HOLDING_REGISTER);
+ sc->s.FRAMING_BIT += result;
+
+ result = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_PMON_PARITY_ERROR_EVENT_COUNT_MSB) << 8;
+ result += exar7250_read(sc, SBE_2T3E3_FRAMER_REG_PMON_HOLDING_REGISTER);
+ sc->s.PARITY_ERROR += result;
+
+ result = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_PMON_FEBE_EVENT_COUNT_MSB) << 8;
+ result += exar7250_read(sc, SBE_2T3E3_FRAMER_REG_PMON_HOLDING_REGISTER);
+ sc->s.FEBE_count += result;
+
+ result = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_PMON_CP_BIT_ERROR_EVENT_COUNT_MSB) << 8;
+ result += exar7250_read(sc, SBE_2T3E3_FRAMER_REG_PMON_HOLDING_REGISTER);
+ sc->s.CP_BIT += result;
+
+ memcpy(stats, &(sc->s), sizeof(t3e3_stats_t));
+}
+
+void t3e3_port_del_stats(struct channel *sc)
+{
+ memset(&(sc->s), 0, sizeof(t3e3_stats_t));
+}
+
+void t3e3_if_config(struct channel *sc, u32 cmd, char *set,
+ t3e3_resp_t *ret, int *rlen)
+{
+ t3e3_param_t *param = (t3e3_param_t *)set;
+ u32 *data = (u32 *)set;
+
+ /* turn off all interrupt */
+ /* cpld_stop_intr(sc); */
+
+ switch (cmd) {
+ case SBE_2T3E3_PORT_GET:
+ t3e3_port_get(sc, &(ret->u.param));
+ *rlen = sizeof(ret->u.param);
+ break;
+ case SBE_2T3E3_PORT_SET:
+ t3e3_port_set(sc, param);
+ *rlen = 0;
+ break;
+ case SBE_2T3E3_PORT_GET_STATS:
+ t3e3_port_get_stats(sc, &(ret->u.stats));
+ *rlen = sizeof(ret->u.stats);
+ break;
+ case SBE_2T3E3_PORT_DEL_STATS:
+ t3e3_port_del_stats(sc);
+ *rlen = 0;
+ break;
+ case SBE_2T3E3_PORT_READ_REGS:
+ t3e3_reg_read(sc, data, &(ret->u.data));
+ *rlen = sizeof(ret->u.data);
+ break;
+ case SBE_2T3E3_PORT_WRITE_REGS:
+#if 0
+ printk(KERN_DEBUG "SBE_2T3E3_PORT_WRITE_REGS, 0x%x, 0x%x, 0x%x\n",
+ ((int*)data)[0], ((int*)data)[1], ((int*)data)[2]);
+#endif
+ t3e3_reg_write(sc, data);
+ *rlen = 0;
+ break;
+ case SBE_2T3E3_LOG_LEVEL:
+ *rlen = 0;
+ break;
+ default:
+ *rlen = 0;
+ break;
+ }
+
+ /* turn on interrupt */
+ /* cpld_start_intr(sc); */
+}
+
+void t3e3_sc_init(struct channel *sc)
+{
+ memset(sc, 0, sizeof(*sc));
+
+ sc->p.frame_mode = SBE_2T3E3_FRAME_MODE_HDLC;
+ sc->p.fractional_mode = SBE_2T3E3_FRACTIONAL_MODE_NONE;
+ sc->p.crc = SBE_2T3E3_CRC_32;
+ sc->p.receiver_on = SBE_2T3E3_OFF;
+ sc->p.transmitter_on = SBE_2T3E3_OFF;
+ sc->p.frame_type = SBE_2T3E3_FRAME_TYPE_T3_CBIT;
+ sc->p.panel = SBE_2T3E3_PANEL_FRONT;
+ sc->p.line_build_out = SBE_2T3E3_OFF;
+ sc->p.receive_equalization = SBE_2T3E3_OFF;
+ sc->p.transmit_all_ones = SBE_2T3E3_OFF;
+ sc->p.loopback = SBE_2T3E3_LOOPBACK_NONE;
+ sc->p.clock_source = SBE_2T3E3_TIMING_LOCAL;
+ sc->p.scrambler = SBE_2T3E3_SCRAMBLER_OFF;
+ sc->p.pad_count = SBE_2T3E3_PAD_COUNT_1;
+}
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#ifndef CTRL_H
+#define CTRL_H
+
+#define SBE_2T3E3_OFF 0
+#define SBE_2T3E3_ON 1
+
+#define SBE_2T3E3_LED_NONE 0
+#define SBE_2T3E3_LED_GREEN 1
+#define SBE_2T3E3_LED_YELLOW 2
+
+#define SBE_2T3E3_CABLE_LENGTH_LESS_THAN_255_FEET 0
+#define SBE_2T3E3_CABLE_LENGTH_GREATER_THAN_255_FEET 1
+
+#define SBE_2T3E3_CRC_16 0
+#define SBE_2T3E3_CRC_32 1
+
+#define SBE_2T3E3_PANEL_FRONT 0
+#define SBE_2T3E3_PANEL_REAR 1
+
+#define SBE_2T3E3_FRAME_MODE_HDLC 0
+#define SBE_2T3E3_FRAME_MODE_TRANSPARENT 1
+#define SBE_2T3E3_FRAME_MODE_RAW 2
+
+#define SBE_2T3E3_FRAME_TYPE_E3_G751 0
+#define SBE_2T3E3_FRAME_TYPE_E3_G832 1
+#define SBE_2T3E3_FRAME_TYPE_T3_CBIT 2
+#define SBE_2T3E3_FRAME_TYPE_T3_M13 3
+
+#define SBE_2T3E3_FRACTIONAL_MODE_NONE 0
+#define SBE_2T3E3_FRACTIONAL_MODE_0 1
+#define SBE_2T3E3_FRACTIONAL_MODE_1 2
+#define SBE_2T3E3_FRACTIONAL_MODE_2 3
+
+#define SBE_2T3E3_SCRAMBLER_OFF 0
+#define SBE_2T3E3_SCRAMBLER_LARSCOM 1
+#define SBE_2T3E3_SCRAMBLER_ADC_KENTROX_DIGITAL 2
+
+#define SBE_2T3E3_TIMING_LOCAL 0
+#define SBE_2T3E3_TIMING_LOOP 1
+
+#define SBE_2T3E3_LOOPBACK_NONE 0
+#define SBE_2T3E3_LOOPBACK_ETHERNET 1
+#define SBE_2T3E3_LOOPBACK_FRAMER 2
+#define SBE_2T3E3_LOOPBACK_LIU_DIGITAL 3
+#define SBE_2T3E3_LOOPBACK_LIU_ANALOG 4
+#define SBE_2T3E3_LOOPBACK_LIU_REMOTE 5
+
+#define SBE_2T3E3_PAD_COUNT_1 1
+#define SBE_2T3E3_PAD_COUNT_2 2
+#define SBE_2T3E3_PAD_COUNT_3 3
+#define SBE_2T3E3_PAD_COUNT_4 4
+
+#define SBE_2T3E3_CHIP_21143 0
+#define SBE_2T3E3_CHIP_CPLD 1
+#define SBE_2T3E3_CHIP_FRAMER 2
+#define SBE_2T3E3_CHIP_LIU 3
+
+#define SBE_2T3E3_LOG_LEVEL_NONE 0
+#define SBE_2T3E3_LOG_LEVEL_ERROR 1
+#define SBE_2T3E3_LOG_LEVEL_WARNING 2
+#define SBE_2T3E3_LOG_LEVEL_INFO 3
+
+/* commands */
+#define SBE_2T3E3_PORT_GET 0
+#define SBE_2T3E3_PORT_SET 1
+#define SBE_2T3E3_PORT_GET_STATS 2
+#define SBE_2T3E3_PORT_DEL_STATS 3
+#define SBE_2T3E3_PORT_READ_REGS 4
+#define SBE_2T3E3_LOG_LEVEL 5
+#define SBE_2T3E3_PORT_WRITE_REGS 6
+
+#define NG_SBE_2T3E3_NODE_TYPE "sbe2T3E3"
+#define NG_SBE_2T3E3_COOKIE 0x03800891
+
+typedef struct t3e3_param {
+ u_int8_t frame_mode; /* FRAME_MODE_* */
+ u_int8_t crc; /* CRC_* */
+ u_int8_t receiver_on; /* ON/OFF */
+ u_int8_t transmitter_on; /* ON/OFF */
+ u_int8_t frame_type; /* FRAME_TYPE_* */
+ u_int8_t panel; /* PANEL_* */
+ u_int8_t line_build_out; /* ON/OFF */
+ u_int8_t receive_equalization; /* ON/OFF */
+ u_int8_t transmit_all_ones; /* ON/OFF */
+ u_int8_t loopback; /* LOOPBACK_* */
+ u_int8_t clock_source; /* TIMING_* */
+ u_int8_t scrambler; /* SCRAMBLER_* */
+ u_int8_t pad_count; /* PAD_COUNT_* */
+ u_int8_t log_level; /* LOG_LEVEL_* - unused */
+ u_int8_t fractional_mode; /* FRACTIONAL_MODE_* */
+ u_int8_t bandwidth_start; /* 0-255 */
+ u_int8_t bandwidth_stop; /* 0-255 */
+} t3e3_param_t;
+
+typedef struct t3e3_stats {
+ u_int64_t in_bytes;
+ u32 in_packets, in_dropped;
+ u32 in_errors, in_error_desc, in_error_coll, in_error_drib,
+ in_error_crc, in_error_mii;
+ u_int64_t out_bytes;
+ u32 out_packets, out_dropped;
+ u32 out_errors, out_error_jab, out_error_lost_carr,
+ out_error_no_carr, out_error_link_fail, out_error_underflow,
+ out_error_dereferred;
+ u_int8_t LOC, LOF, OOF, LOS, AIS, FERF, IDLE, AIC, FEAC;
+ u_int16_t FEBE_code;
+ u32 LCV, FRAMING_BIT, PARITY_ERROR, FEBE_count, CP_BIT;
+} t3e3_stats_t;
+
+
+typedef struct t3e3_resp {
+ union {
+ t3e3_param_t param;
+ t3e3_stats_t stats;
+ u32 data;
+ } u;
+} t3e3_resp_t;
+
+#endif /* CTRL_H */
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include <linux/netdevice.h>
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include "2t3e3.h"
+#include "ctrl.h"
+
+void dc_init(struct channel *sc)
+{
+ u32 val;
+
+ dc_stop(sc);
+ /*dc_reset(sc);*/ /* do not want to reset here */
+
+ /*
+ * BUS_MODE (CSR0)
+ */
+ val = SBE_2T3E3_21143_VAL_READ_LINE_ENABLE |
+ SBE_2T3E3_21143_VAL_READ_MULTIPLE_ENABLE |
+ SBE_2T3E3_21143_VAL_TRANSMIT_AUTOMATIC_POLLING_200us |
+ SBE_2T3E3_21143_VAL_BUS_ARBITRATION_RR;
+
+ if (sc->h.command & 16)
+ val |= SBE_2T3E3_21143_VAL_WRITE_AND_INVALIDATE_ENABLE;
+
+ switch (sc->h.cache_size) {
+ case 32:
+ val |= SBE_2T3E3_21143_VAL_CACHE_ALIGNMENT_32;
+ break;
+ case 16:
+ val |= SBE_2T3E3_21143_VAL_CACHE_ALIGNMENT_16;
+ break;
+ case 8:
+ val |= SBE_2T3E3_21143_VAL_CACHE_ALIGNMENT_8;
+ break;
+ default:
+ break;
+ }
+
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_BUS_MODE, val);
+
+ /* OPERATION_MODE (CSR6) */
+ val = SBE_2T3E3_21143_VAL_RECEIVE_ALL |
+ SBE_2T3E3_21143_VAL_MUST_BE_ONE |
+ SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_1 |
+ SBE_2T3E3_21143_VAL_LOOPBACK_OFF |
+ SBE_2T3E3_21143_VAL_PASS_ALL_MULTICAST |
+ SBE_2T3E3_21143_VAL_PROMISCUOUS_MODE |
+ SBE_2T3E3_21143_VAL_PASS_BAD_FRAMES;
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE, val);
+ if (sc->p.loopback == SBE_2T3E3_LOOPBACK_ETHERNET)
+ sc->p.loopback = SBE_2T3E3_LOOPBACK_NONE;
+
+#if 0 /* No need to clear this register - and it may be in use */
+ /*
+ * BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT (CSR9)
+ */
+ val = 0;
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT, val);
+#endif
+
+ /*
+ * GENERAL_PURPOSE_TIMER_AND_INTERRUPT_MITIGATION_CONTROL (CSR11)
+ */
+ val = SBE_2T3E3_21143_VAL_CYCLE_SIZE |
+ SBE_2T3E3_21143_VAL_TRANSMIT_TIMER |
+ SBE_2T3E3_21143_VAL_NUMBER_OF_TRANSMIT_PACKETS |
+ SBE_2T3E3_21143_VAL_RECEIVE_TIMER |
+ SBE_2T3E3_21143_VAL_NUMBER_OF_RECEIVE_PACKETS;
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_GENERAL_PURPOSE_TIMER_AND_INTERRUPT_MITIGATION_CONTROL, val);
+
+ /* prepare descriptors and data for receive and transmit procecsses */
+ if (dc_init_descriptor_list(sc) != 0)
+ return;
+
+ /* clear ethernet interrupts status */
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_STATUS, 0xFFFFFFFF);
+
+ /* SIA mode registers */
+ dc_set_output_port(sc);
+}
+
+void dc_start(struct channel *sc)
+{
+ u32 val;
+
+ if (!(sc->r.flags & SBE_2T3E3_FLAG_NETWORK_UP))
+ return;
+
+ dc_init(sc);
+
+ /* get actual LOS and OOF status */
+ switch (sc->p.frame_type) {
+ case SBE_2T3E3_FRAME_TYPE_E3_G751:
+ case SBE_2T3E3_FRAME_TYPE_E3_G832:
+ val = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_CONFIGURATION_STATUS_2);
+ dev_dbg(&sc->pdev->dev, "Start Framer Rx Status = %02X\n", val);
+ sc->s.OOF = val & SBE_2T3E3_FRAMER_VAL_E3_RX_OOF ? 1 : 0;
+ break;
+ case SBE_2T3E3_FRAME_TYPE_T3_CBIT:
+ case SBE_2T3E3_FRAME_TYPE_T3_M13:
+ val = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_CONFIGURATION_STATUS);
+ dev_dbg(&sc->pdev->dev, "Start Framer Rx Status = %02X\n", val);
+ sc->s.OOF = val & SBE_2T3E3_FRAMER_VAL_T3_RX_OOF ? 1 : 0;
+ break;
+ default:
+ break;
+ }
+ cpld_LOS_update(sc);
+
+ /* start receive and transmit processes */
+ dc_transmitter_onoff(sc, SBE_2T3E3_ON);
+ dc_receiver_onoff(sc, SBE_2T3E3_ON);
+
+ /* start interrupts */
+ dc_start_intr(sc);
+}
+
+#define MAX_INT_WAIT_CNT 12000
+void dc_stop(struct channel *sc)
+{
+ int wcnt;
+
+ /* stop receive and transmit processes */
+ dc_receiver_onoff(sc, SBE_2T3E3_OFF);
+ dc_transmitter_onoff(sc, SBE_2T3E3_OFF);
+
+ /* turn off ethernet interrupts */
+ dc_stop_intr(sc);
+
+ /* wait to ensure the interrupts have been completed */
+ for (wcnt = 0; wcnt < MAX_INT_WAIT_CNT; wcnt++) {
+ udelay(5);
+ if (!sc->interrupt_active)
+ break;
+ }
+ if (wcnt >= MAX_INT_WAIT_CNT)
+ dev_warn(&sc->pdev->dev, "SBE 2T3E3: Interrupt active too long\n");
+
+ /* clear all receive/transmit data */
+ dc_drop_descriptor_list(sc);
+}
+
+void dc_start_intr(struct channel *sc)
+{
+ if (sc->p.loopback == SBE_2T3E3_LOOPBACK_NONE && sc->s.OOF)
+ return;
+
+ if (sc->p.receiver_on || sc->p.transmitter_on) {
+ if (!sc->ether.interrupt_enable_mask)
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_STATUS, 0xFFFFFFFF);
+
+ sc->ether.interrupt_enable_mask =
+ SBE_2T3E3_21143_VAL_NORMAL_INTERRUPT_SUMMARY_ENABLE |
+ SBE_2T3E3_21143_VAL_ABNORMAL_INTERRUPT_SUMMARY_ENABLE |
+ SBE_2T3E3_21143_VAL_RECEIVE_STOPPED_ENABLE |
+ SBE_2T3E3_21143_VAL_RECEIVE_BUFFER_UNAVAILABLE_ENABLE |
+ SBE_2T3E3_21143_VAL_RECEIVE_INTERRUPT_ENABLE |
+ SBE_2T3E3_21143_VAL_TRANSMIT_UNDERFLOW_INTERRUPT_ENABLE |
+ SBE_2T3E3_21143_VAL_TRANSMIT_BUFFER_UNAVAILABLE_ENABLE |
+ SBE_2T3E3_21143_VAL_TRANSMIT_STOPPED_ENABLE |
+ SBE_2T3E3_21143_VAL_TRANSMIT_INTERRUPT_ENABLE;
+
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_INTERRUPT_ENABLE,
+ sc->ether.interrupt_enable_mask);
+ }
+}
+
+void dc_stop_intr(struct channel *sc)
+{
+ sc->ether.interrupt_enable_mask = 0;
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_INTERRUPT_ENABLE, 0);
+}
+
+void dc_reset(struct channel *sc)
+{
+ /* turn off ethernet interrupts */
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_INTERRUPT_ENABLE, 0);
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_STATUS, 0xFFFFFFFF);
+
+ /* software reset */
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_BUS_MODE,
+ SBE_2T3E3_21143_VAL_SOFTWARE_RESET);
+ udelay(4); /* 50 PCI cycles < 2us */
+
+ /* clear hardware configuration */
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_BUS_MODE, 0);
+
+ /* clear software configuration */
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE, 0);
+
+ /* turn off SIA reset */
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_SIA_CONNECTIVITY,
+ SBE_2T3E3_21143_VAL_SIA_RESET);
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_SIA_TRANSMIT_AND_RECEIVE, 0);
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_SIA_AND_GENERAL_PURPOSE_PORT, 0);
+}
+
+
+void dc_receiver_onoff(struct channel *sc, u32 mode)
+{
+ u32 i, state = 0;
+
+ if (sc->p.receiver_on == mode)
+ return;
+
+ switch (mode) {
+ case SBE_2T3E3_OFF:
+ if (dc_read(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE) &
+ SBE_2T3E3_21143_VAL_RECEIVE_START) {
+ dc_clear_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_RECEIVE_START);
+
+ for (i = 0; i < 16; i++) {
+ state = dc_read(sc->addr, SBE_2T3E3_21143_REG_STATUS) &
+ SBE_2T3E3_21143_VAL_RECEIVE_PROCESS_STATE;
+ if (state == SBE_2T3E3_21143_VAL_RX_STOPPED)
+ break;
+ udelay(5);
+ }
+ if (state != SBE_2T3E3_21143_VAL_RX_STOPPED)
+ dev_warn(&sc->pdev->dev, "SBE 2T3E3: Rx failed to stop\n");
+ else
+ dev_info(&sc->pdev->dev, "SBE 2T3E3: Rx off\n");
+ }
+ break;
+ case SBE_2T3E3_ON:
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_RECEIVE_START);
+ udelay(100);
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_RECEIVE_POLL_DEMAND, 0xFFFFFFFF);
+ break;
+ default:
+ return;
+ }
+
+ sc->p.receiver_on = mode;
+}
+
+void dc_transmitter_onoff(struct channel *sc, u32 mode)
+{
+ u32 i, state = 0;
+
+ if (sc->p.transmitter_on == mode)
+ return;
+
+ switch (mode) {
+ case SBE_2T3E3_OFF:
+ if (dc_read(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE) &
+ SBE_2T3E3_21143_VAL_TRANSMISSION_START) {
+ dc_clear_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_TRANSMISSION_START);
+
+ for (i = 0; i < 16; i++) {
+ state = dc_read(sc->addr, SBE_2T3E3_21143_REG_STATUS) &
+ SBE_2T3E3_21143_VAL_TRANSMISSION_PROCESS_STATE;
+ if (state == SBE_2T3E3_21143_VAL_TX_STOPPED)
+ break;
+ udelay(5);
+ }
+ if (state != SBE_2T3E3_21143_VAL_TX_STOPPED)
+ dev_warn(&sc->pdev->dev, "SBE 2T3E3: Tx failed to stop\n");
+ }
+ break;
+ case SBE_2T3E3_ON:
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_TRANSMISSION_START);
+ udelay(100);
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_TRANSMIT_POLL_DEMAND, 0xFFFFFFFF);
+ break;
+ default:
+ return;
+ }
+
+ sc->p.transmitter_on = mode;
+}
+
+
+
+void dc_set_loopback(struct channel *sc, u32 mode)
+{
+ u32 val;
+
+ switch (mode) {
+ case SBE_2T3E3_21143_VAL_LOOPBACK_OFF:
+ case SBE_2T3E3_21143_VAL_LOOPBACK_INTERNAL:
+ break;
+ default:
+ return;
+ }
+
+#if 0
+ /* restart SIA */
+ dc_clear_bits(sc->addr, SBE_2T3E3_21143_REG_SIA_CONNECTIVITY,
+ SBE_2T3E3_21143_VAL_SIA_RESET);
+ udelay(1000);
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_SIA_CONNECTIVITY,
+ SBE_2T3E3_21143_VAL_SIA_RESET);
+#endif
+
+ /* select loopback mode */
+ val = dc_read(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE) &
+ ~SBE_2T3E3_21143_VAL_OPERATING_MODE;
+ val |= mode;
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE, val);
+
+ if (mode == SBE_2T3E3_21143_VAL_LOOPBACK_OFF)
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_FULL_DUPLEX_MODE);
+ else
+ dc_clear_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_FULL_DUPLEX_MODE);
+}
+
+u32 dc_init_descriptor_list(struct channel *sc)
+{
+ u32 i, j;
+ struct sk_buff *m;
+
+ if (sc->ether.rx_ring == NULL)
+ sc->ether.rx_ring = kzalloc(SBE_2T3E3_RX_DESC_RING_SIZE *
+ sizeof(t3e3_rx_desc_t), GFP_KERNEL);
+ if (sc->ether.rx_ring == NULL) {
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: no buffer space for RX ring\n");
+ return ENOMEM;
+ }
+
+ if (sc->ether.tx_ring == NULL)
+ sc->ether.tx_ring = kzalloc(SBE_2T3E3_TX_DESC_RING_SIZE *
+ sizeof(t3e3_tx_desc_t), GFP_KERNEL);
+ if (sc->ether.tx_ring == NULL) {
+#ifdef T3E3_USE_CONTIGMALLOC
+ t3e3_contigmemory_size = SBE_2T3E3_RX_DESC_RING_SIZE *
+ sizeof(t3e3_rx_desc_t);
+#endif
+ kfree(sc->ether.rx_ring);
+ sc->ether.rx_ring = NULL;
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: no buffer space for RX ring\n");
+ return ENOMEM;
+ }
+
+
+ /*
+ * Receive ring
+ */
+ for (i = 0; i < SBE_2T3E3_RX_DESC_RING_SIZE; i++) {
+ sc->ether.rx_ring[i].rdes0 = SBE_2T3E3_RX_DESC_21143_OWN;
+ sc->ether.rx_ring[i].rdes1 =
+ SBE_2T3E3_RX_DESC_SECOND_ADDRESS_CHAINED | SBE_2T3E3_MTU;
+
+ if (sc->ether.rx_data[i] == NULL) {
+ if (!(m = dev_alloc_skb(MCLBYTES))) {
+ for (j = 0; j < i; j++) {
+ dev_kfree_skb_any(sc->ether.rx_data[j]);
+ sc->ether.rx_data[j] = NULL;
+ }
+#ifdef T3E3_USE_CONTIGMALLOC
+ t3e3_contigmemory_size = SBE_2T3E3_RX_DESC_RING_SIZE *
+ sizeof(t3e3_rx_desc_t);
+#endif
+ kfree(sc->ether.rx_ring);
+ sc->ether.rx_ring = NULL;
+#ifdef T3E3_USE_CONTIGMALLOC
+ t3e3_contigmemory_size = SBE_2T3E3_TX_DESC_RING_SIZE *
+ sizeof(t3e3_tx_desc_t);
+#endif
+ kfree(sc->ether.tx_ring);
+ sc->ether.tx_ring = NULL;
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: token_alloc err:"
+ " no buffer space for RX ring\n");
+ return ENOBUFS;
+ }
+ sc->ether.rx_data[i] = m;
+ }
+ sc->ether.rx_ring[i].rdes2 = virt_to_phys(sc->ether.rx_data[i]->data);
+
+ sc->ether.rx_ring[i].rdes3 = virt_to_phys(
+ &sc->ether.rx_ring[(i + 1) % SBE_2T3E3_RX_DESC_RING_SIZE]);
+ }
+ sc->ether.rx_ring[SBE_2T3E3_RX_DESC_RING_SIZE - 1].rdes1 |=
+ SBE_2T3E3_RX_DESC_END_OF_RING;
+ sc->ether.rx_ring_current_read = 0;
+
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_RECEIVE_LIST_BASE_ADDRESS,
+ virt_to_phys(&sc->ether.rx_ring[0]));
+
+ /*
+ * Transmit ring
+ */
+ for (i = 0; i < SBE_2T3E3_TX_DESC_RING_SIZE; i++) {
+ sc->ether.tx_ring[i].tdes0 = 0;
+ sc->ether.tx_ring[i].tdes1 = SBE_2T3E3_TX_DESC_SECOND_ADDRESS_CHAINED |
+ SBE_2T3E3_TX_DESC_DISABLE_PADDING;
+
+ sc->ether.tx_ring[i].tdes2 = 0;
+ sc->ether.tx_data[i] = NULL;
+
+ sc->ether.tx_ring[i].tdes3 = virt_to_phys(
+ &sc->ether.tx_ring[(i + 1) % SBE_2T3E3_TX_DESC_RING_SIZE]);
+ }
+ sc->ether.tx_ring[SBE_2T3E3_TX_DESC_RING_SIZE - 1].tdes1 |=
+ SBE_2T3E3_TX_DESC_END_OF_RING;
+
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_TRANSMIT_LIST_BASE_ADDRESS,
+ virt_to_phys(&sc->ether.tx_ring[0]));
+ sc->ether.tx_ring_current_read = 0;
+ sc->ether.tx_ring_current_write = 0;
+ sc->ether.tx_free_cnt = SBE_2T3E3_TX_DESC_RING_SIZE;
+ spin_lock_init(&sc->ether.tx_lock);
+
+ return 0;
+}
+
+void dc_clear_descriptor_list(struct channel *sc)
+{
+ u32 i;
+
+ /* clear CSR3 and CSR4 */
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_RECEIVE_LIST_BASE_ADDRESS, 0);
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_TRANSMIT_LIST_BASE_ADDRESS, 0);
+
+ /* free all data buffers on TX ring */
+ for (i = 0; i < SBE_2T3E3_TX_DESC_RING_SIZE; i++) {
+ if (sc->ether.tx_data[i] != NULL) {
+ dev_kfree_skb_any(sc->ether.tx_data[i]);
+ sc->ether.tx_data[i] = NULL;
+ }
+ }
+}
+
+void dc_drop_descriptor_list(struct channel *sc)
+{
+ u32 i;
+
+ dc_clear_descriptor_list(sc);
+
+ /* free all data buffers on RX ring */
+ for (i = 0; i < SBE_2T3E3_RX_DESC_RING_SIZE; i++) {
+ if (sc->ether.rx_data[i] != NULL) {
+ dev_kfree_skb_any(sc->ether.rx_data[i]);
+ sc->ether.rx_data[i] = NULL;
+ }
+ }
+
+ if (sc->ether.rx_ring != NULL) {
+#ifdef T3E3_USE_CONTIGMALLOC
+ t3e3_contigmemory_size = SBE_2T3E3_RX_DESC_RING_SIZE *
+ sizeof(t3e3_rx_desc_t);
+#endif
+ kfree(sc->ether.rx_ring);
+ sc->ether.rx_ring = NULL;
+ }
+
+ if (sc->ether.tx_ring != NULL) {
+#ifdef T3E3_USE_CONTIGMALLOC
+ t3e3_contigmemory_size = SBE_2T3E3_TX_DESC_RING_SIZE *
+ sizeof(t3e3_tx_desc_t);
+#endif
+ kfree(sc->ether.tx_ring);
+ sc->ether.tx_ring = NULL;
+ }
+}
+
+
+void dc_set_output_port(struct channel *sc)
+{
+ dc_clear_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_PORT_SELECT);
+
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_SIA_STATUS, 0x00000301);
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_SIA_CONNECTIVITY, 0);
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_SIA_TRANSMIT_AND_RECEIVE, 0);
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_SIA_AND_GENERAL_PURPOSE_PORT, 0x08000011);
+
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_TRANSMIT_THRESHOLD_MODE_100Mbs |
+ SBE_2T3E3_21143_VAL_HEARTBEAT_DISABLE |
+ SBE_2T3E3_21143_VAL_PORT_SELECT |
+ SBE_2T3E3_21143_VAL_FULL_DUPLEX_MODE);
+}
+
+void dc_restart(struct channel *sc)
+{
+ dev_warn(&sc->pdev->dev, "SBE 2T3E3: 21143 restart\n");
+
+ dc_stop(sc);
+ dc_reset(sc);
+ dc_init(sc); /* stop + reset + init */
+ dc_start(sc);
+}
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include "2t3e3.h"
+#include "ctrl.h"
+
+void exar7250_init(struct channel *sc)
+{
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_OPERATING_MODE,
+ SBE_2T3E3_FRAMER_VAL_T3_CBIT |
+ SBE_2T3E3_FRAMER_VAL_INTERRUPT_ENABLE_RESET |
+ SBE_2T3E3_FRAMER_VAL_TIMING_ASYNCH_TXINCLK);
+
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_IO_CONTROL,
+ SBE_2T3E3_FRAMER_VAL_DISABLE_TX_LOSS_OF_CLOCK |
+ SBE_2T3E3_FRAMER_VAL_DISABLE_RX_LOSS_OF_CLOCK |
+ SBE_2T3E3_FRAMER_VAL_AMI_LINE_CODE |
+ SBE_2T3E3_FRAMER_VAL_RX_LINE_CLOCK_INVERT);
+
+ exar7250_set_frame_type(sc, SBE_2T3E3_FRAME_TYPE_T3_CBIT);
+}
+
+void exar7250_set_frame_type(struct channel *sc, u32 type)
+{
+ u32 val;
+
+ switch (type) {
+ case SBE_2T3E3_FRAME_TYPE_E3_G751:
+ case SBE_2T3E3_FRAME_TYPE_E3_G832:
+ case SBE_2T3E3_FRAME_TYPE_T3_CBIT:
+ case SBE_2T3E3_FRAME_TYPE_T3_M13:
+ break;
+ default:
+ return;
+ }
+
+ exar7250_stop_intr(sc, type);
+
+ val = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_OPERATING_MODE);
+ val &= ~(SBE_2T3E3_FRAMER_VAL_LOCAL_LOOPBACK_MODE |
+ SBE_2T3E3_FRAMER_VAL_T3_E3_SELECT |
+ SBE_2T3E3_FRAMER_VAL_FRAME_FORMAT_SELECT);
+ switch (type) {
+ case SBE_2T3E3_FRAME_TYPE_E3_G751:
+ val |= SBE_2T3E3_FRAMER_VAL_E3_G751;
+ break;
+ case SBE_2T3E3_FRAME_TYPE_E3_G832:
+ val |= SBE_2T3E3_FRAMER_VAL_E3_G832;
+ break;
+ case SBE_2T3E3_FRAME_TYPE_T3_CBIT:
+ val |= SBE_2T3E3_FRAMER_VAL_T3_CBIT;
+ break;
+ case SBE_2T3E3_FRAME_TYPE_T3_M13:
+ val |= SBE_2T3E3_FRAMER_VAL_T3_M13;
+ break;
+ default:
+ return;
+ }
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_OPERATING_MODE, val);
+ exar7250_start_intr(sc, type);
+}
+
+
+void exar7250_start_intr(struct channel *sc, u32 type)
+{
+ u32 val;
+
+ switch (type) {
+ case SBE_2T3E3_FRAME_TYPE_E3_G751:
+ case SBE_2T3E3_FRAME_TYPE_E3_G832:
+ val = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_CONFIGURATION_STATUS_2);
+#if 0
+ sc->s.LOS = val & SBE_2T3E3_FRAMER_VAL_E3_RX_LOS ? 1 : 0;
+#else
+ cpld_LOS_update(sc);
+#endif
+ sc->s.OOF = val & SBE_2T3E3_FRAMER_VAL_E3_RX_OOF ? 1 : 0;
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_STATUS_1);
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_ENABLE_1,
+ SBE_2T3E3_FRAMER_VAL_E3_RX_OOF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_LOS_INTERRUPT_ENABLE);
+#if 0
+ /*SBE_2T3E3_FRAMER_VAL_E3_RX_COFA_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_OOF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_LOF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_LOS_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_AIS_INTERRUPT_ENABLE);*/
+#endif
+
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_STATUS_2);
+#if 0
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_ENABLE_2,
+ SBE_2T3E3_FRAMER_VAL_E3_RX_FEBE_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_FERF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_FRAMING_BYTE_ERROR_INTERRUPT_ENABLE);
+#endif
+ break;
+
+ case SBE_2T3E3_FRAME_TYPE_T3_CBIT:
+ case SBE_2T3E3_FRAME_TYPE_T3_M13:
+ val = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_CONFIGURATION_STATUS);
+#if 0
+ sc->s.LOS = val & SBE_2T3E3_FRAMER_VAL_T3_RX_LOS ? 1 : 0;
+#else
+ cpld_LOS_update(sc);
+#endif
+ sc->s.OOF = val & SBE_2T3E3_FRAMER_VAL_T3_RX_OOF ? 1 : 0;
+
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_INTERRUPT_STATUS);
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_T3_RX_INTERRUPT_ENABLE,
+ SBE_2T3E3_FRAMER_VAL_T3_RX_LOS_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_OOF_INTERRUPT_ENABLE);
+#if 0
+ /* SBE_2T3E3_FRAMER_VAL_T3_RX_CP_BIT_ERROR_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_LOS_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_AIS_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_IDLE_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_FERF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_AIC_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_OOF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_P_BIT_INTERRUPT_ENABLE);*/
+#endif
+
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_FEAC_INTERRUPT_ENABLE_STATUS);
+#if 0
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_T3_RX_FEAC_INTERRUPT_ENABLE_STATUS,
+ SBE_2T3E3_FRAMER_VAL_T3_RX_FEAC_REMOVE_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_FEAC_VALID_INTERRUPT_ENABLE);
+#endif
+
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_T3_RX_LAPD_CONTROL, 0);
+ break;
+
+ default:
+ return;
+ }
+
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_BLOCK_INTERRUPT_STATUS);
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_BLOCK_INTERRUPT_ENABLE,
+ SBE_2T3E3_FRAMER_VAL_RX_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_TX_INTERRUPT_ENABLE);
+}
+
+
+void exar7250_stop_intr(struct channel *sc, u32 type)
+{
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_BLOCK_INTERRUPT_ENABLE, 0);
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_BLOCK_INTERRUPT_STATUS);
+
+ switch (type) {
+ case SBE_2T3E3_FRAME_TYPE_E3_G751:
+ case SBE_2T3E3_FRAME_TYPE_E3_G832:
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_ENABLE_1, 0);
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_STATUS_1);
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_ENABLE_2, 0);
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_STATUS_2);
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_E3_RX_LAPD_CONTROL, 0);
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_LAPD_CONTROL);
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_E3_TX_LAPD_STATUS, 0);
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_TX_LAPD_STATUS);
+ break;
+
+ case SBE_2T3E3_FRAME_TYPE_T3_CBIT:
+ case SBE_2T3E3_FRAME_TYPE_T3_M13:
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_T3_RX_INTERRUPT_ENABLE, 0);
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_INTERRUPT_STATUS);
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_T3_RX_FEAC_INTERRUPT_ENABLE_STATUS, 0);
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_FEAC_INTERRUPT_ENABLE_STATUS);
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_T3_RX_LAPD_CONTROL, 0);
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_LAPD_CONTROL);
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_T3_TX_FEAC_CONFIGURATION_STATUS, 0);
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_TX_FEAC_CONFIGURATION_STATUS);
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_T3_TX_LAPD_STATUS, 0);
+ exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_TX_LAPD_STATUS);
+ break;
+ }
+}
+
+
+
+
+void exar7250_unipolar_onoff(struct channel *sc, u32 mode)
+{
+ switch (mode) {
+ case SBE_2T3E3_OFF:
+ exar7300_clear_bit(sc, SBE_2T3E3_FRAMER_REG_IO_CONTROL,
+ SBE_2T3E3_FRAMER_VAL_UNIPOLAR);
+ break;
+ case SBE_2T3E3_ON:
+ exar7300_set_bit(sc, SBE_2T3E3_FRAMER_REG_IO_CONTROL,
+ SBE_2T3E3_FRAMER_VAL_UNIPOLAR);
+ break;
+ }
+}
+
+void exar7250_set_loopback(struct channel *sc, u32 mode)
+{
+ switch (mode) {
+ case SBE_2T3E3_FRAMER_VAL_LOOPBACK_OFF:
+ exar7300_clear_bit(sc, SBE_2T3E3_FRAMER_REG_OPERATING_MODE,
+ SBE_2T3E3_FRAMER_VAL_LOCAL_LOOPBACK_MODE);
+ break;
+ case SBE_2T3E3_FRAMER_VAL_LOOPBACK_ON:
+ exar7300_set_bit(sc, SBE_2T3E3_FRAMER_REG_OPERATING_MODE,
+ SBE_2T3E3_FRAMER_VAL_LOCAL_LOOPBACK_MODE);
+ break;
+ }
+}
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include "2t3e3.h"
+#include "ctrl.h"
+
+void exar7300_init(struct channel *sc)
+{
+ exar7300_write(sc, SBE_2T3E3_LIU_REG_REG1, 0);
+
+ /* enable line decodeer and encoder */
+ exar7300_write(sc, SBE_2T3E3_LIU_REG_REG2, 0);
+ exar7300_write(sc, SBE_2T3E3_LIU_REG_REG3, 0);
+ exar7300_write(sc, SBE_2T3E3_LIU_REG_REG4,
+ SBE_2T3E3_LIU_VAL_T3_MODE_SELECT |
+ SBE_2T3E3_LIU_VAL_LOOPBACK_OFF);
+}
+
+void exar7300_set_loopback(struct channel *sc, u32 mode)
+{
+ u32 val;
+
+ switch (mode) {
+ case SBE_2T3E3_LIU_VAL_LOOPBACK_OFF:
+ case SBE_2T3E3_LIU_VAL_LOOPBACK_REMOTE:
+ case SBE_2T3E3_LIU_VAL_LOOPBACK_ANALOG:
+ case SBE_2T3E3_LIU_VAL_LOOPBACK_DIGITAL:
+ break;
+ default:
+ return;
+ }
+
+ val = exar7300_read(sc, SBE_2T3E3_LIU_REG_REG4);
+ val &= ~(SBE_2T3E3_LIU_VAL_LOCAL_LOOPBACK | SBE_2T3E3_LIU_VAL_REMOTE_LOOPBACK);
+ val |= mode;
+ exar7300_write(sc, SBE_2T3E3_LIU_REG_REG4, val);
+
+#if 0
+ /* TODO - is it necessary? idea from 2T3E3_HW_Test_code */
+ switch (mode) {
+ case SBE_2T3E3_LIU_VAL_LOOPBACK_OFF:
+ break;
+ case SBE_2T3E3_LIU_VAL_LOOPBACK_REMOTE:
+ exar7300_receive_equalization_onoff(sc, SBE_2T3E3_ON);
+ break;
+ case SBE_2T3E3_LIU_VAL_LOOPBACK_ANALOG:
+ exar7300_receive_equalization_onoff(sc, SBE_2T3E3_OFF);
+ break;
+ case SBE_2T3E3_LIU_VAL_LOOPBACK_DIGITAL:
+ exar7300_receive_equalization_onoff(sc, SBE_2T3E3_ON);
+ break;
+ }
+#endif
+}
+
+void exar7300_set_frame_type(struct channel *sc, u32 type)
+{
+ u32 val;
+
+ switch (type) {
+ case SBE_2T3E3_FRAME_TYPE_T3_CBIT:
+ case SBE_2T3E3_FRAME_TYPE_T3_M13:
+ case SBE_2T3E3_FRAME_TYPE_E3_G751:
+ case SBE_2T3E3_FRAME_TYPE_E3_G832:
+ break;
+ default:
+ return;
+ }
+
+ val = exar7300_read(sc, SBE_2T3E3_LIU_REG_REG4);
+ val &= ~(SBE_2T3E3_LIU_VAL_T3_MODE_SELECT |
+ SBE_2T3E3_LIU_VAL_E3_MODE_SELECT);
+
+ switch (type) {
+ case SBE_2T3E3_FRAME_TYPE_T3_CBIT:
+ case SBE_2T3E3_FRAME_TYPE_T3_M13:
+ val |= SBE_2T3E3_LIU_VAL_T3_MODE_SELECT;
+ break;
+ case SBE_2T3E3_FRAME_TYPE_E3_G751:
+ case SBE_2T3E3_FRAME_TYPE_E3_G832:
+ val |= SBE_2T3E3_LIU_VAL_E3_MODE_SELECT;
+ break;
+ default:
+ return;
+ }
+
+ exar7300_write(sc, SBE_2T3E3_LIU_REG_REG4, val);
+}
+
+
+void exar7300_transmit_all_ones_onoff(struct channel *sc, u32 mode)
+{
+ if (sc->p.transmit_all_ones == mode)
+ return;
+
+ switch (mode) {
+ case SBE_2T3E3_ON:
+ exar7300_set_bit(sc, SBE_2T3E3_LIU_REG_REG1,
+ SBE_2T3E3_LIU_VAL_TRANSMIT_ALL_ONES);
+ break;
+ case SBE_2T3E3_OFF:
+ exar7300_clear_bit(sc, SBE_2T3E3_LIU_REG_REG1,
+ SBE_2T3E3_LIU_VAL_TRANSMIT_ALL_ONES);
+ break;
+ default:
+ return;
+ }
+
+ sc->p.transmit_all_ones = mode;
+}
+
+void exar7300_receive_equalization_onoff(struct channel *sc, u32 mode)
+{
+ if (sc->p.receive_equalization == mode)
+ return;
+
+ switch (mode) {
+ case SBE_2T3E3_OFF:
+ exar7300_set_bit(sc, SBE_2T3E3_LIU_REG_REG2,
+ SBE_2T3E3_LIU_VAL_RECEIVE_EQUALIZATION_DISABLE);
+ break;
+ case SBE_2T3E3_ON:
+ exar7300_clear_bit(sc, SBE_2T3E3_LIU_REG_REG2,
+ SBE_2T3E3_LIU_VAL_RECEIVE_EQUALIZATION_DISABLE);
+ break;
+ default:
+ return;
+ }
+
+ sc->p.receive_equalization = mode;
+}
+
+void exar7300_line_build_out_onoff(struct channel *sc, u32 mode)
+{
+ if (sc->p.line_build_out == mode)
+ return;
+
+ switch (mode) {
+ case SBE_2T3E3_OFF:
+ exar7300_set_bit(sc, SBE_2T3E3_LIU_REG_REG1,
+ SBE_2T3E3_LIU_VAL_TRANSMIT_LEVEL_SELECT);
+ exar7300_receive_equalization_onoff(sc, SBE_2T3E3_OFF);
+ break;
+ case SBE_2T3E3_ON:
+ exar7300_clear_bit(sc, SBE_2T3E3_LIU_REG_REG1,
+ SBE_2T3E3_LIU_VAL_TRANSMIT_LEVEL_SELECT);
+ exar7300_receive_equalization_onoff(sc, SBE_2T3E3_ON);
+ break;
+ default:
+ return;
+ }
+
+ sc->p.line_build_out = mode;
+}
+
+/* TODO - what about encoder in raw mode??? disable it too? */
+void exar7300_unipolar_onoff(struct channel *sc, u32 mode)
+{
+ switch (mode) {
+ case SBE_2T3E3_OFF:
+ exar7300_clear_bit(sc, SBE_2T3E3_LIU_REG_REG3,
+ SBE_2T3E3_LIU_VAL_DECODER_DISABLE);
+ exar7300_clear_bit(sc, SBE_2T3E3_LIU_REG_REG1,
+ SBE_2T3E3_LIU_VAL_TRANSMIT_BINARY_DATA);
+ break;
+ case SBE_2T3E3_ON:
+ exar7300_set_bit(sc, SBE_2T3E3_LIU_REG_REG3,
+ SBE_2T3E3_LIU_VAL_DECODER_DISABLE);
+ exar7300_set_bit(sc, SBE_2T3E3_LIU_REG_REG1,
+ SBE_2T3E3_LIU_VAL_TRANSMIT_BINARY_DATA);
+ break;
+ }
+}
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include <linux/hdlc.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include "2t3e3.h"
+
+irqreturn_t t3e3_intr(int irq, void *dev_instance)
+{
+ struct channel *sc = dev_to_priv(dev_instance);
+ u32 val;
+ irqreturn_t ret = IRQ_NONE;
+
+ sc->interrupt_active = 1;
+
+ val = cpld_read(sc, SBE_2T3E3_CPLD_REG_PICSR);
+
+ if (val & SBE_2T3E3_CPLD_VAL_RECEIVE_LOSS_OF_SIGNAL_CHANGE) {
+ dev_dbg(&sc->pdev->dev,
+ "Rx LOS Chng Int r=%02x (LOS|OOF=%02x)\n",
+ val, (sc->s.LOS << 4) | sc->s.OOF);
+ cpld_LOS_update(sc);
+ ret = IRQ_HANDLED;
+ }
+
+ if (val & SBE_2T3E3_CPLD_VAL_INTERRUPT_FROM_ETHERNET_ASSERTED) {
+ dc_intr(sc);
+ ret = IRQ_HANDLED;
+ }
+
+ if (val & SBE_2T3E3_CPLD_VAL_INTERRUPT_FROM_FRAMER_ASSERTED) {
+ exar7250_intr(sc);
+ ret = IRQ_HANDLED;
+ }
+
+ /*
+ we don't care about other interrupt sources (DMO, LOS, LCV) because
+ they are handled by Framer too
+ */
+
+ sc->interrupt_active = 0;
+ return ret;
+}
+
+void dc_intr(struct channel *sc)
+{
+ u32 val;
+
+ /* disable ethernet interrupts */
+ /* grrr this clears interrupt summary bits !!! */
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_INTERRUPT_ENABLE, 0);
+
+ while ((val = dc_read(sc->addr, SBE_2T3E3_21143_REG_STATUS)) &
+ (SBE_2T3E3_21143_VAL_RECEIVE_PROCESS_STOPPED |
+ SBE_2T3E3_21143_VAL_RECEIVE_BUFFER_UNAVAILABLE |
+ SBE_2T3E3_21143_VAL_RECEIVE_INTERRUPT |
+ SBE_2T3E3_21143_VAL_TRANSMIT_UNDERFLOW |
+ SBE_2T3E3_21143_VAL_TRANSMIT_BUFFER_UNAVAILABLE |
+ SBE_2T3E3_21143_VAL_TRANSMIT_PROCESS_STOPPED |
+ SBE_2T3E3_21143_VAL_TRANSMIT_INTERRUPT)) {
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_STATUS, val);
+
+ dev_dbg(&sc->pdev->dev, "SBE 2T3E3: Ethernet controller interrupt! (CSR5 = %08X)\n",
+ val);
+
+ if (val & (SBE_2T3E3_21143_VAL_RECEIVE_INTERRUPT |
+ SBE_2T3E3_21143_VAL_RECEIVE_BUFFER_UNAVAILABLE |
+ SBE_2T3E3_21143_VAL_RECEIVE_PROCESS_STOPPED)) {
+ if (val & SBE_2T3E3_21143_VAL_RECEIVE_INTERRUPT)
+ dev_dbg(&sc->pdev->dev,
+ "Receive interrupt (LOS=%d, OOF=%d)\n",
+ sc->s.LOS, sc->s.OOF);
+ if (val & SBE_2T3E3_21143_VAL_RECEIVE_BUFFER_UNAVAILABLE)
+ dev_dbg(&sc->pdev->dev,
+ "Receive buffer unavailable\n");
+ if (val & SBE_2T3E3_21143_VAL_RECEIVE_PROCESS_STOPPED)
+ dev_dbg(&sc->pdev->dev,
+ "Receive process stopped\n");
+ dc_intr_rx(sc);
+ }
+
+ if (val & SBE_2T3E3_21143_VAL_TRANSMIT_UNDERFLOW) {
+ dev_dbg(&sc->pdev->dev, "Transmit underflow\n");
+ dc_intr_tx_underflow(sc);
+ }
+
+ if (val & (SBE_2T3E3_21143_VAL_TRANSMIT_BUFFER_UNAVAILABLE |
+ SBE_2T3E3_21143_VAL_TRANSMIT_INTERRUPT |
+ SBE_2T3E3_21143_VAL_TRANSMIT_PROCESS_STOPPED)) {
+ if (val & SBE_2T3E3_21143_VAL_TRANSMIT_INTERRUPT)
+ dev_dbg(&sc->pdev->dev, "Transmit interrupt\n");
+ if (val & SBE_2T3E3_21143_VAL_TRANSMIT_BUFFER_UNAVAILABLE)
+ dev_dbg(&sc->pdev->dev,
+ "Transmit buffer unavailable\n");
+ if (val & SBE_2T3E3_21143_VAL_TRANSMIT_PROCESS_STOPPED)
+ dev_dbg(&sc->pdev->dev,
+ "Transmit process stopped\n");
+ dc_intr_tx(sc);
+ }
+ }
+
+ /* enable ethernet interrupts */
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_INTERRUPT_ENABLE,
+ sc->ether.interrupt_enable_mask);
+}
+
+void dc_intr_rx(struct channel *sc)
+{
+ u32 current_read;
+ u32 error_mask, error;
+ t3e3_rx_desc_t *current_desc;
+ struct sk_buff *m, *m2;
+ unsigned rcv_len;
+
+ sc->rcv_count++; /* for the activity LED */
+
+ current_read = sc->ether.rx_ring_current_read;
+ dev_dbg(&sc->pdev->dev, "intr_rx current_read = %d\n", current_read);
+
+ /* when ethernet loopback is set, ignore framer signals */
+ if ((sc->p.loopback != SBE_2T3E3_LOOPBACK_ETHERNET) && sc->s.OOF) {
+ while (!(sc->ether.rx_ring[current_read].rdes0 &
+ SBE_2T3E3_RX_DESC_21143_OWN)) {
+ current_desc = &sc->ether.rx_ring[current_read];
+ current_desc->rdes1 &= SBE_2T3E3_RX_DESC_END_OF_RING |
+ SBE_2T3E3_RX_DESC_SECOND_ADDRESS_CHAINED;
+ current_desc->rdes1 |= SBE_2T3E3_MTU;
+ current_desc->rdes0 = SBE_2T3E3_RX_DESC_21143_OWN;
+ current_read = (current_read + 1) % SBE_2T3E3_RX_DESC_RING_SIZE;
+ }
+ sc->ether.rx_ring_current_read = current_read;
+ return;
+ }
+
+ while (!(sc->ether.rx_ring[current_read].rdes0 &
+ SBE_2T3E3_RX_DESC_21143_OWN)) {
+ current_desc = &sc->ether.rx_ring[current_read];
+
+ dev_dbg(&sc->pdev->dev, "rdes0: %08X rdes1: %08X\n",
+ current_desc->rdes0, current_desc->rdes1);
+
+ m = sc->ether.rx_data[current_read];
+ rcv_len = (current_desc->rdes0 & SBE_2T3E3_RX_DESC_FRAME_LENGTH) >>
+ SBE_2T3E3_RX_DESC_FRAME_LENGTH_SHIFT;
+
+ dev_dbg(&sc->pdev->dev, "mbuf was received (mbuf len = %d)\n",
+ rcv_len);
+
+ switch (sc->p.crc) {
+ case SBE_2T3E3_CRC_16:
+ rcv_len -= SBE_2T3E3_CRC16_LENGTH;
+ break;
+ case SBE_2T3E3_CRC_32:
+ rcv_len -= SBE_2T3E3_CRC32_LENGTH;
+ break;
+ default:
+ break;
+ }
+
+ if (current_desc->rdes0 & SBE_2T3E3_RX_DESC_LAST_DESC) {
+
+ /* TODO: is collision possible? */
+ error_mask = SBE_2T3E3_RX_DESC_DESC_ERROR |
+ SBE_2T3E3_RX_DESC_COLLISION_SEEN |
+ SBE_2T3E3_RX_DESC_DRIBBLING_BIT;
+
+ switch (sc->p.frame_mode) {
+ case SBE_2T3E3_FRAME_MODE_HDLC:
+ error_mask |= SBE_2T3E3_RX_DESC_MII_ERROR;
+ if (sc->p.crc == SBE_2T3E3_CRC_32)
+ error_mask |= SBE_2T3E3_RX_DESC_CRC_ERROR;
+ break;
+ case SBE_2T3E3_FRAME_MODE_TRANSPARENT:
+ case SBE_2T3E3_FRAME_MODE_RAW:
+ break;
+ default:
+ error_mask = 0;
+ }
+
+ if (sc->s.LOS) {
+ error_mask &= ~(SBE_2T3E3_RX_DESC_DRIBBLING_BIT ||
+ SBE_2T3E3_RX_DESC_MII_ERROR);
+ }
+
+ error = current_desc->rdes0 & error_mask;
+ if (error) {
+ sc->s.in_errors++;
+ dev_dbg(&sc->pdev->dev,
+ "error interrupt: NO_ERROR_MESSAGE = %d\n",
+ sc->r.flags & SBE_2T3E3_FLAG_NO_ERROR_MESSAGES ? 1 : 0);
+
+ current_desc->rdes1 &= SBE_2T3E3_RX_DESC_END_OF_RING |
+ SBE_2T3E3_RX_DESC_SECOND_ADDRESS_CHAINED;
+ current_desc->rdes1 |= SBE_2T3E3_MTU;
+ current_desc->rdes0 = SBE_2T3E3_RX_DESC_21143_OWN;
+
+ if (error & SBE_2T3E3_RX_DESC_DESC_ERROR) {
+ if (!(sc->r.flags & SBE_2T3E3_FLAG_NO_ERROR_MESSAGES))
+ dev_err(&sc->pdev->dev,
+ "SBE 2T3E3: descriptor error\n");
+ sc->s.in_error_desc++;
+ }
+
+ if (error & SBE_2T3E3_RX_DESC_COLLISION_SEEN) {
+ if (!(sc->r.flags & SBE_2T3E3_FLAG_NO_ERROR_MESSAGES))
+ dev_err(&sc->pdev->dev,
+ "SBE 2T3E3: collision seen\n");
+ sc->s.in_error_coll++;
+ } else {
+ if (error & SBE_2T3E3_RX_DESC_DRIBBLING_BIT) {
+ if (!(sc->r.flags & SBE_2T3E3_FLAG_NO_ERROR_MESSAGES))
+ dev_err(&sc->pdev->dev,
+ "SBE 2T3E3: dribbling bits error\n");
+ sc->s.in_error_drib++;
+ }
+
+ if (error & SBE_2T3E3_RX_DESC_CRC_ERROR) {
+ if (!(sc->r.flags & SBE_2T3E3_FLAG_NO_ERROR_MESSAGES))
+ dev_err(&sc->pdev->dev,
+ "SBE 2T3E3: crc error\n");
+ sc->s.in_error_crc++;
+ }
+ }
+
+ if (error & SBE_2T3E3_RX_DESC_MII_ERROR) {
+ if (!(sc->r.flags & SBE_2T3E3_FLAG_NO_ERROR_MESSAGES))
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: mii error\n");
+ sc->s.in_error_mii++;
+ }
+
+ current_read = (current_read + 1) % SBE_2T3E3_RX_DESC_RING_SIZE;
+ sc->r.flags |= SBE_2T3E3_FLAG_NO_ERROR_MESSAGES;
+ continue;
+ }
+ }
+
+ current_desc->rdes1 &= SBE_2T3E3_RX_DESC_END_OF_RING |
+ SBE_2T3E3_RX_DESC_SECOND_ADDRESS_CHAINED;
+ current_desc->rdes1 |= SBE_2T3E3_MTU;
+
+ if (rcv_len > 1600) {
+ sc->s.in_errors++;
+ sc->s.in_dropped++;
+ if (!(sc->r.flags & SBE_2T3E3_FLAG_NO_ERROR_MESSAGES))
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: oversized rx: rdes0 = %08X\n",
+ current_desc->rdes0);
+ } else {
+ m2 = dev_alloc_skb(MCLBYTES);
+ if (m2 != NULL) {
+ current_desc->rdes2 = virt_to_phys(m2->data);
+ sc->ether.rx_data[current_read] = m2;
+ sc->s.in_packets++;
+ sc->s.in_bytes += rcv_len;
+ m->dev = sc->dev;
+ skb_put(m, rcv_len);
+ skb_reset_mac_header(m);
+ m->protocol = hdlc_type_trans(m, m->dev);
+ netif_rx(m);
+
+ /* good packet was received so we will show error messages again... */
+ if (sc->r.flags & SBE_2T3E3_FLAG_NO_ERROR_MESSAGES) {
+ dev_dbg(&sc->pdev->dev,
+ "setting ERROR_MESSAGES->0\n");
+ sc->r.flags &= ~SBE_2T3E3_FLAG_NO_ERROR_MESSAGES;
+ }
+
+ } else {
+ sc->s.in_errors++;
+ sc->s.in_dropped++;
+ }
+ }
+ current_desc->rdes0 = SBE_2T3E3_RX_DESC_21143_OWN;
+ current_read = (current_read + 1) % SBE_2T3E3_RX_DESC_RING_SIZE;
+ }
+
+ sc->ether.rx_ring_current_read = current_read;
+
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_RECEIVE_POLL_DEMAND, 0xFFFFFFFF);
+}
+
+void dc_intr_tx(struct channel *sc)
+{
+ u32 current_read, current_write;
+ u32 last_segment, error;
+ t3e3_tx_desc_t *current_desc;
+
+ spin_lock(&sc->ether.tx_lock);
+
+ current_read = sc->ether.tx_ring_current_read;
+ current_write = sc->ether.tx_ring_current_write;
+
+ while (current_read != current_write) {
+ current_desc = &sc->ether.tx_ring[current_read];
+
+ if (current_desc->tdes0 & SBE_2T3E3_RX_DESC_21143_OWN)
+ break;
+
+ dev_dbg(&sc->pdev->dev,
+ "txeof: tdes0 = %08X tdes1 = %08X\n",
+ current_desc->tdes0, current_desc->tdes1);
+
+ error = current_desc->tdes0 & (SBE_2T3E3_TX_DESC_ERROR_SUMMARY |
+ SBE_2T3E3_TX_DESC_TRANSMIT_JABBER_TIMEOUT |
+ SBE_2T3E3_TX_DESC_LOSS_OF_CARRIER |
+ SBE_2T3E3_TX_DESC_NO_CARRIER |
+ SBE_2T3E3_TX_DESC_LINK_FAIL_REPORT |
+ SBE_2T3E3_TX_DESC_UNDERFLOW_ERROR |
+ SBE_2T3E3_TX_DESC_DEFFERED);
+
+ last_segment = current_desc->tdes1 & SBE_2T3E3_TX_DESC_LAST_SEGMENT;
+
+ current_desc->tdes0 = 0;
+ current_desc->tdes1 &= SBE_2T3E3_TX_DESC_END_OF_RING |
+ SBE_2T3E3_TX_DESC_SECOND_ADDRESS_CHAINED;
+ current_desc->tdes2 = 0;
+ sc->ether.tx_free_cnt++;
+
+ if (last_segment != SBE_2T3E3_TX_DESC_LAST_SEGMENT) {
+ current_read = (current_read + 1) % SBE_2T3E3_TX_DESC_RING_SIZE;
+ continue;
+ }
+
+
+ if (sc->ether.tx_data[current_read]) {
+ sc->s.out_packets++;
+ sc->s.out_bytes += sc->ether.tx_data[current_read]->len;
+ dev_kfree_skb_any(sc->ether.tx_data[current_read]);
+ sc->ether.tx_data[current_read] = NULL;
+ }
+
+ if (error > 0) {
+ sc->s.out_errors++;
+
+ if (error & SBE_2T3E3_TX_DESC_TRANSMIT_JABBER_TIMEOUT) {
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: transmit jabber timeout\n");
+ sc->s.out_error_jab++;
+ }
+
+ if (sc->p.loopback != SBE_2T3E3_LOOPBACK_ETHERNET) {
+ if (error & SBE_2T3E3_TX_DESC_LOSS_OF_CARRIER) {
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: loss of carrier\n");
+ sc->s.out_error_lost_carr++;
+ }
+
+ if (error & SBE_2T3E3_TX_DESC_NO_CARRIER) {
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: no carrier\n");
+ sc->s.out_error_no_carr++;
+ }
+ }
+
+ if (error & SBE_2T3E3_TX_DESC_LINK_FAIL_REPORT) {
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: link fail report\n");
+ sc->s.out_error_link_fail++;
+ }
+
+ if (error & SBE_2T3E3_TX_DESC_UNDERFLOW_ERROR) {
+ dev_err(&sc->pdev->dev, "SBE 2T3E3:"
+ " transmission underflow error\n");
+ sc->s.out_error_underflow++;
+ spin_unlock(&sc->ether.tx_lock);
+
+ dc_restart(sc);
+ return;
+ }
+
+ if (error & SBE_2T3E3_TX_DESC_DEFFERED) {
+ dev_err(&sc->pdev->dev, "SBE 2T3E3: transmission deferred\n");
+ sc->s.out_error_dereferred++;
+ }
+ }
+
+ current_read = (current_read + 1) % SBE_2T3E3_TX_DESC_RING_SIZE;
+ }
+
+ sc->ether.tx_ring_current_read = current_read;
+
+ /* Relieve flow control when the TX queue is drained at least half way */
+ if (sc->ether.tx_full &&
+ (sc->ether.tx_free_cnt >= (SBE_2T3E3_TX_DESC_RING_SIZE / 2))) {
+ sc->ether.tx_full = 0;
+ netif_wake_queue(sc->dev);
+ }
+ spin_unlock(&sc->ether.tx_lock);
+}
+
+
+void dc_intr_tx_underflow(struct channel *sc)
+{
+ u32 val;
+
+ dc_transmitter_onoff(sc, SBE_2T3E3_OFF);
+
+ val = dc_read(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE);
+ dc_clear_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS);
+
+ switch (val & SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS) {
+ case SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_1:
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_2);
+ break;
+ case SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_2:
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_3);
+ break;
+ case SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_3:
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_4);
+ break;
+ case SBE_2T3E3_21143_VAL_THRESHOLD_CONTROL_BITS_4:
+ default:
+ dc_set_bits(sc->addr, SBE_2T3E3_21143_REG_OPERATION_MODE,
+ SBE_2T3E3_21143_VAL_STORE_AND_FORWARD);
+ break;
+ }
+
+ dc_transmitter_onoff(sc, SBE_2T3E3_ON);
+}
+
+
+
+
+void exar7250_intr(struct channel *sc)
+{
+ u32 status, old_OOF;
+
+#if 0
+ /* disable interrupts */
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_BLOCK_INTERRUPT_ENABLE, 0);
+#endif
+
+ old_OOF = sc->s.OOF;
+
+ status = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_BLOCK_INTERRUPT_STATUS);
+ dev_dbg(&sc->pdev->dev, "SBE 2T3E3: Framer interrupt! (REG[0x05] = %02X)\n", status);
+
+ switch (sc->p.frame_type) {
+ case SBE_2T3E3_FRAME_TYPE_E3_G751:
+ case SBE_2T3E3_FRAME_TYPE_E3_G832:
+ exar7250_E3_intr(sc, status);
+ break;
+
+ case SBE_2T3E3_FRAME_TYPE_T3_CBIT:
+ case SBE_2T3E3_FRAME_TYPE_T3_M13:
+ exar7250_T3_intr(sc, status);
+ break;
+
+ default:
+ break;
+ }
+
+ if (sc->s.OOF != old_OOF) {
+ if (sc->s.OOF) {
+ if (sc->p.loopback == SBE_2T3E3_LOOPBACK_NONE) {
+ dev_dbg(&sc->pdev->dev, "SBE 2T3E3: Disabling eth interrupts\n");
+ /* turn off ethernet interrupts */
+ dc_stop_intr(sc);
+ }
+ } else if (sc->r.flags & SBE_2T3E3_FLAG_NETWORK_UP) {
+ dev_dbg(&sc->pdev->dev, "SBE 2T3E3: Enabling eth interrupts\n");
+ /* start interrupts */
+ sc->s.OOF = 1;
+ dc_intr_rx(sc);
+ sc->s.OOF = 0;
+ if (sc->p.receiver_on) {
+ dc_receiver_onoff(sc, SBE_2T3E3_OFF);
+ dc_receiver_onoff(sc, SBE_2T3E3_ON);
+ }
+ dc_start_intr(sc);
+ }
+ }
+#if 0
+ /* reenable interrupts */
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_BLOCK_INTERRUPT_ENABLE,
+ SBE_2T3E3_FRAMER_VAL_RX_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_TX_INTERRUPT_ENABLE
+ );
+#endif
+}
+
+
+void exar7250_T3_intr(struct channel *sc, u32 block_status)
+{
+ u32 status, result;
+
+ if (block_status & SBE_2T3E3_FRAMER_VAL_RX_INTERRUPT_STATUS) {
+ status = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_INTERRUPT_STATUS);
+
+ if (status) {
+ dev_dbg(&sc->pdev->dev,
+ "Framer interrupt T3 RX (REG[0x13] = %02X)\n",
+ status);
+
+ result = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_CONFIGURATION_STATUS);
+
+#if 0
+ if (status & SBE_2T3E3_FRAMER_VAL_T3_RX_LOS_INTERRUPT_STATUS) {
+ dev_dbg(&sc->pdev->dev,
+ "Framer interrupt T3: LOS\n");
+ sc->s.LOS = result & SBE_2T3E3_FRAMER_VAL_T3_RX_LOS ? 1 : 0;
+
+ }
+#else
+ cpld_LOS_update(sc);
+#endif
+ if (status & SBE_2T3E3_FRAMER_VAL_T3_RX_OOF_INTERRUPT_STATUS) {
+ sc->s.OOF = result & SBE_2T3E3_FRAMER_VAL_T3_RX_OOF ? 1 : 0;
+ dev_dbg(&sc->pdev->dev,
+ "Framer interrupt T3: OOF (%d)\n",
+ sc->s.OOF);
+ }
+
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_T3_RX_INTERRUPT_ENABLE,
+ SBE_2T3E3_FRAMER_VAL_T3_RX_LOS_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_OOF_INTERRUPT_ENABLE);
+#if 0
+ SBE_2T3E3_FRAMER_VAL_T3_RX_CP_BIT_ERROR_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_LOS_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_AIS_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_IDLE_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_FERF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_AIC_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_OOF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_P_BIT_INTERRUPT_ENABLE
+#endif
+ }
+
+ status = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_FEAC_INTERRUPT_ENABLE_STATUS);
+ if (status) {
+ dev_dbg(&sc->pdev->dev,
+ "Framer interrupt T3 RX (REG[0x17] = %02X)\n",
+ status);
+#if 0
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_T3_RX_FEAC_INTERRUPT_ENABLE_STATUS,
+ SBE_2T3E3_FRAMER_VAL_T3_RX_FEAC_REMOVE_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_T3_RX_FEAC_VALID_INTERRUPT_ENABLE
+ );
+#endif
+ }
+
+ status = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_RX_LAPD_CONTROL);
+ if (status)
+ dev_dbg(&sc->pdev->dev,
+ "Framer interrupt T3 RX (REG[0x18] = %02X)\n",
+ status);
+ }
+
+
+ if (block_status & SBE_2T3E3_FRAMER_VAL_TX_INTERRUPT_STATUS) {
+ status = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_TX_FEAC_CONFIGURATION_STATUS);
+ dev_dbg(&sc->pdev->dev, "SBE 2T3E3: Framer interrupt T3 TX (REG[0x31] = %02X)\n",
+ status);
+
+ status = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_T3_TX_LAPD_STATUS);
+ dev_dbg(&sc->pdev->dev, "SBE 2T3E3: Framer interrupt T3 TX (REG[0x34] = %02X)\n",
+ status);
+ }
+}
+
+
+void exar7250_E3_intr(struct channel *sc, u32 block_status)
+{
+ u32 status, result;
+
+ if (block_status & SBE_2T3E3_FRAMER_VAL_RX_INTERRUPT_STATUS) {
+ status = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_STATUS_1);
+
+ if (status) {
+ dev_dbg(&sc->pdev->dev,
+ "Framer interrupt E3 RX (REG[0x14] = %02X)\n",
+ status);
+
+ result = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_CONFIGURATION_STATUS_2);
+
+#if 0
+ if (status & SBE_2T3E3_FRAMER_VAL_E3_RX_LOS_INTERRUPT_STATUS) {
+ dev_dbg(&sc->pdev->dev,
+ "Framer interrupt E3: LOS\n");
+ sc->s.LOS = result & SBE_2T3E3_FRAMER_VAL_E3_RX_LOS ? 1 : 0;
+ }
+#else
+ cpld_LOS_update(sc);
+#endif
+ if (status & SBE_2T3E3_FRAMER_VAL_E3_RX_OOF_INTERRUPT_STATUS) {
+ sc->s.OOF = result & SBE_2T3E3_FRAMER_VAL_E3_RX_OOF ? 1 : 0;
+ dev_dbg(&sc->pdev->dev,
+ "Framer interrupt E3: OOF (%d)\n",
+ sc->s.OOF);
+ }
+
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_ENABLE_1,
+ SBE_2T3E3_FRAMER_VAL_E3_RX_OOF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_LOS_INTERRUPT_ENABLE
+ );
+#if 0
+ SBE_2T3E3_FRAMER_VAL_E3_RX_COFA_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_OOF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_LOF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_LOS_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_AIS_INTERRUPT_ENABLE
+#endif
+ }
+
+ status = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_STATUS_2);
+ if (status) {
+ dev_dbg(&sc->pdev->dev,
+ "Framer interrupt E3 RX (REG[0x15] = %02X)\n",
+ status);
+
+#if 0
+ exar7250_write(sc, SBE_2T3E3_FRAMER_REG_E3_RX_INTERRUPT_ENABLE_2,
+ SBE_2T3E3_FRAMER_VAL_E3_RX_FEBE_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_FERF_INTERRUPT_ENABLE |
+ SBE_2T3E3_FRAMER_VAL_E3_RX_FRAMING_BYTE_ERROR_INTERRUPT_ENABLE);
+#endif
+ }
+
+ }
+
+ if (block_status & SBE_2T3E3_FRAMER_VAL_TX_INTERRUPT_STATUS) {
+ status = exar7250_read(sc, SBE_2T3E3_FRAMER_REG_E3_TX_LAPD_STATUS);
+ dev_dbg(&sc->pdev->dev, "SBE 2T3E3: Framer interrupt E3 TX (REG[0x34] = %02X)\n",
+ status);
+ }
+}
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include <linux/ip.h>
+#include <asm/system.h>
+#include "2t3e3.h"
+#include "ctrl.h"
+
+/* All access to registers done via the 21143 on port 0 must be
+ * protected via the card->bootrom_lock. */
+
+/* priviate define to be used here only - must be protected by card->bootrom_lock */
+#define cpld_write_nolock(channel, reg, val) \
+ bootrom_write((channel), CPLD_MAP_REG(reg, channel), val)
+
+u32 cpld_read(struct channel *channel, u32 reg)
+{
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&channel->card->bootrom_lock, flags);
+ val = bootrom_read((channel), CPLD_MAP_REG(reg, channel));
+ spin_unlock_irqrestore(&channel->card->bootrom_lock, flags);
+ return val;
+}
+
+/****************************************
+ * Access via BootROM port
+ ****************************************/
+
+u32 bootrom_read(struct channel *channel, u32 reg)
+{
+ unsigned long addr = channel->card->bootrom_addr;
+ u32 result;
+
+ /* select BootROM address */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_PROGRAMMING_ADDRESS, reg & 0x3FFFF);
+
+ /* select reading from BootROM */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_READ_OPERATION |
+ SBE_2T3E3_21143_VAL_BOOT_ROM_SELECT);
+
+ udelay(2); /* 20 PCI cycles */
+
+ /* read from BootROM */
+ result = dc_read(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT) & 0xff;
+
+ /* reset CSR9 */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT, 0);
+
+ return result;
+}
+
+void bootrom_write(struct channel *channel, u32 reg, u32 val)
+{
+ unsigned long addr = channel->card->bootrom_addr;
+
+ /* select BootROM address */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_PROGRAMMING_ADDRESS, reg & 0x3FFFF);
+
+ /* select writting to BootROM */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_WRITE_OPERATION |
+ SBE_2T3E3_21143_VAL_BOOT_ROM_SELECT |
+ (val & 0xff));
+
+ udelay(2); /* 20 PCI cycles */
+
+ /* reset CSR9 */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT, 0);
+}
+
+
+/****************************************
+ * Access via Serial I/O port
+ ****************************************/
+
+static u32 serialrom_read_bit(struct channel *channel)
+{
+ unsigned long addr = channel->card->bootrom_addr;
+ u32 bit;
+
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_READ_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CLOCK |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT); /* clock high */
+
+ bit = (dc_read(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT) &
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_DATA_OUT) > 0 ? 1 : 0;
+
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_READ_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT); /* clock low */
+
+ return bit;
+}
+
+static void serialrom_write_bit(struct channel *channel, u32 bit)
+{
+ unsigned long addr = channel->card->bootrom_addr;
+ u32 lastbit = -1;
+
+ bit &= 1;
+
+ if (bit != lastbit) {
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_WRITE_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT |
+ (bit << 2)); /* clock low */
+
+ lastbit = bit;
+ }
+
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_WRITE_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CLOCK |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT |
+ (bit << 2)); /* clock high */
+
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_WRITE_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT |
+ (bit << 2)); /* clock low */
+}
+
+/****************************************
+ * Access to SerialROM (eeprom)
+ ****************************************/
+
+u32 t3e3_eeprom_read_word(struct channel *channel, u32 address)
+{
+ unsigned long addr = channel->card->bootrom_addr;
+ u32 i, val;
+ unsigned long flags;
+
+ address &= 0x3f;
+
+ spin_lock_irqsave(&channel->card->bootrom_lock, flags);
+
+ /* select correct Serial Chip */
+ cpld_write_nolock(channel, SBE_2T3E3_CPLD_REG_SERIAL_CHIP_SELECT,
+ SBE_2T3E3_CPLD_VAL_EEPROM_SELECT);
+
+ /* select reading from Serial I/O Bus */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_READ_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT); /* clock low */
+
+ /* select read operation */
+ serialrom_write_bit(channel, 0);
+ serialrom_write_bit(channel, 1);
+ serialrom_write_bit(channel, 1);
+ serialrom_write_bit(channel, 0);
+
+ for (i = 0x20; i; i >>= 1)
+ serialrom_write_bit(channel, address & i ? 1 : 0);
+
+ val = 0;
+ for (i = 0x8000; i; i >>= 1)
+ val |= (serialrom_read_bit(channel) ? i : 0);
+
+ /* Reset 21143's CSR9 */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_READ_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT); /* clock low */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT, 0);
+
+ /* Unselect Serial Chip */
+ cpld_write_nolock(channel, SBE_2T3E3_CPLD_REG_SERIAL_CHIP_SELECT, 0);
+
+ spin_unlock_irqrestore(&channel->card->bootrom_lock, flags);
+
+ return ntohs(val);
+}
+
+
+/****************************************
+ * Access to Framer
+ ****************************************/
+
+u32 exar7250_read(struct channel *channel, u32 reg)
+{
+ u32 result;
+ unsigned long flags;
+
+#if 0
+ switch (reg) {
+ case SBE_2T3E3_FRAMER_REG_OPERATING_MODE:
+ return channel->framer_regs[reg];
+ break;
+ default:
+ }
+#endif
+
+ spin_lock_irqsave(&channel->card->bootrom_lock, flags);
+
+ result = bootrom_read(channel, cpld_reg_map[SBE_2T3E3_CPLD_REG_FRAMER_BASE_ADDRESS]
+ [channel->h.slot] + (t3e3_framer_reg_map[reg] << 2));
+
+ spin_unlock_irqrestore(&channel->card->bootrom_lock, flags);
+
+ return result;
+}
+
+void exar7250_write(struct channel *channel, u32 reg, u32 val)
+{
+ unsigned long flags;
+
+ val &= 0xff;
+ channel->framer_regs[reg] = val;
+
+ spin_lock_irqsave(&channel->card->bootrom_lock, flags);
+
+ bootrom_write(channel, cpld_reg_map[SBE_2T3E3_CPLD_REG_FRAMER_BASE_ADDRESS]
+ [channel->h.slot] + (t3e3_framer_reg_map[reg] << 2), val);
+
+ spin_unlock_irqrestore(&channel->card->bootrom_lock, flags);
+}
+
+
+/****************************************
+ * Access to LIU
+ ****************************************/
+
+u32 exar7300_read(struct channel *channel, u32 reg)
+{
+ unsigned long addr = channel->card->bootrom_addr, flags;
+ u32 i, val;
+
+#if 0
+ switch (reg) {
+ case SBE_2T3E3_LIU_REG_REG1:
+ case SBE_2T3E3_LIU_REG_REG2:
+ case SBE_2T3E3_LIU_REG_REG3:
+ case SBE_2T3E3_LIU_REG_REG4:
+ return channel->liu_regs[reg];
+ break;
+ default:
+ }
+#endif
+
+ /* select correct Serial Chip */
+
+ spin_lock_irqsave(&channel->card->bootrom_lock, flags);
+
+ cpld_write_nolock(channel, SBE_2T3E3_CPLD_REG_SERIAL_CHIP_SELECT,
+ cpld_val_map[SBE_2T3E3_CPLD_VAL_LIU_SELECT][channel->h.slot]);
+
+ /* select reading from Serial I/O Bus */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_READ_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT); /* clock low */
+
+ /* select read operation */
+ serialrom_write_bit(channel, 1);
+
+ /* Exar7300 register address is 4 bit long */
+ reg = t3e3_liu_reg_map[reg];
+ for (i = 0; i < 4; i++, reg >>= 1) /* 4 bits of SerialROM address */
+ serialrom_write_bit(channel, reg & 1);
+ for (i = 0; i < 3; i++) /* remaining 3 bits of SerialROM address */
+ serialrom_write_bit(channel, 0);
+
+ val = 0; /* Exar7300 register value is 5 bit long */
+ for (i = 0; i < 8; i++) /* 8 bits of SerialROM value */
+ val += (serialrom_read_bit(channel) << i);
+
+ /* Reset 21143's CSR9 */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_READ_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT); /* clock low */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT, 0);
+
+ /* Unselect Serial Chip */
+ cpld_write_nolock(channel, SBE_2T3E3_CPLD_REG_SERIAL_CHIP_SELECT, 0);
+
+ spin_unlock_irqrestore(&channel->card->bootrom_lock, flags);
+
+ return val;
+}
+
+void exar7300_write(struct channel *channel, u32 reg, u32 val)
+{
+ unsigned long addr = channel->card->bootrom_addr, flags;
+ u32 i;
+
+ channel->liu_regs[reg] = val;
+
+ /* select correct Serial Chip */
+
+ spin_lock_irqsave(&channel->card->bootrom_lock, flags);
+
+ cpld_write_nolock(channel, SBE_2T3E3_CPLD_REG_SERIAL_CHIP_SELECT,
+ cpld_val_map[SBE_2T3E3_CPLD_VAL_LIU_SELECT][channel->h.slot]);
+
+ /* select writting to Serial I/O Bus */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_WRITE_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT); /* clock low */
+
+ /* select write operation */
+ serialrom_write_bit(channel, 0);
+
+ /* Exar7300 register address is 4 bit long */
+ reg = t3e3_liu_reg_map[reg];
+ for (i = 0; i < 4; i++) { /* 4 bits */
+ serialrom_write_bit(channel, reg & 1);
+ reg >>= 1;
+ }
+ for (i = 0; i < 3; i++) /* remaining 3 bits of SerialROM address */
+ serialrom_write_bit(channel, 0);
+
+ /* Exar7300 register value is 5 bit long */
+ for (i = 0; i < 5; i++) {
+ serialrom_write_bit(channel, val & 1);
+ val >>= 1;
+ }
+ for (i = 0; i < 3; i++) /* remaining 3 bits of SerialROM value */
+ serialrom_write_bit(channel, 0);
+
+ /* Reset 21143_CSR9 */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT,
+ SBE_2T3E3_21143_VAL_WRITE_OPERATION |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_SELECT |
+ SBE_2T3E3_21143_VAL_SERIAL_ROM_CHIP_SELECT); /* clock low */
+ dc_write(addr, SBE_2T3E3_21143_REG_BOOT_ROM_SERIAL_ROM_AND_MII_MANAGEMENT, 0);
+
+ /* Unselect Serial Chip */
+ cpld_write_nolock(channel, SBE_2T3E3_CPLD_REG_SERIAL_CHIP_SELECT, 0);
+
+ spin_unlock_irqrestore(&channel->card->bootrom_lock, flags);
+}
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include "2t3e3.h"
+
+void t3e3_init(struct channel *sc)
+{
+ cpld_init(sc);
+ dc_reset(sc);
+ dc_init(sc);
+ exar7250_init(sc);
+ exar7300_init(sc);
+}
+
+int t3e3_if_start_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+ struct channel *sc = dev_to_priv(dev);
+ u32 current_write, last_write;
+ unsigned long flags;
+ struct sk_buff *skb2;
+
+ if (skb == NULL) {
+ sc->s.out_errors++;
+ return 0;
+ }
+
+ if (sc->p.transmitter_on != SBE_2T3E3_ON) {
+ sc->s.out_errors++;
+ sc->s.out_dropped++;
+ dev_kfree_skb_any(skb);
+ return 0;
+ }
+
+ if (sc->s.OOF && sc->p.loopback == SBE_2T3E3_LOOPBACK_NONE) {
+ sc->s.out_dropped++;
+ dev_kfree_skb_any(skb);
+ return 0;
+ }
+
+ spin_lock_irqsave(&sc->ether.tx_lock, flags);
+
+ current_write = sc->ether.tx_ring_current_write;
+ for (skb2 = skb; skb2 != NULL; skb2 = NULL) {
+ if (skb2->len) {
+ if ((sc->ether.tx_ring[current_write].tdes1 &
+ SBE_2T3E3_TX_DESC_BUFFER_1_SIZE) > 0)
+ break;
+ current_write = (current_write + 1) % SBE_2T3E3_TX_DESC_RING_SIZE;
+ /*
+ * Leave at least 1 tx desc free so that dc_intr_tx() can
+ * identify empty list
+ */
+ if (current_write == sc->ether.tx_ring_current_read)
+ break;
+ }
+ }
+ if (skb2 != NULL) {
+ netif_stop_queue(sc->dev);
+ sc->ether.tx_full = 1;
+ dev_dbg(&sc->pdev->dev, "SBE 2T3E3: out of descriptors\n");
+ spin_unlock_irqrestore(&sc->ether.tx_lock, flags);
+ return NETDEV_TX_BUSY;
+ }
+
+ current_write = last_write = sc->ether.tx_ring_current_write;
+ dev_dbg(&sc->pdev->dev, "sending mbuf (current_write = %d)\n",
+ current_write);
+
+ for (skb2 = skb; skb2 != NULL; skb2 = NULL) {
+ if (skb2->len) {
+ dev_dbg(&sc->pdev->dev,
+ "sending mbuf (len = %d, next = %p)\n",
+ skb2->len, NULL);
+
+ sc->ether.tx_free_cnt--;
+ sc->ether.tx_ring[current_write].tdes0 = 0;
+ sc->ether.tx_ring[current_write].tdes1 &=
+ SBE_2T3E3_TX_DESC_END_OF_RING |
+ SBE_2T3E3_TX_DESC_SECOND_ADDRESS_CHAINED;
+/* DISABLE_PADDING sometimes gets lost somehow, hands off... */
+ sc->ether.tx_ring[current_write].tdes1 |=
+ SBE_2T3E3_TX_DESC_DISABLE_PADDING | skb2->len;
+
+ if (current_write == sc->ether.tx_ring_current_write) {
+ sc->ether.tx_ring[current_write].tdes1 |=
+ SBE_2T3E3_TX_DESC_FIRST_SEGMENT;
+ } else {
+ sc->ether.tx_ring[current_write].tdes0 =
+ SBE_2T3E3_TX_DESC_21143_OWN;
+ }
+
+ sc->ether.tx_ring[current_write].tdes2 = virt_to_phys(skb2->data);
+ sc->ether.tx_data[current_write] = NULL;
+
+ last_write = current_write;
+ current_write = (current_write + 1) % SBE_2T3E3_TX_DESC_RING_SIZE;
+ }
+ }
+
+ sc->ether.tx_data[last_write] = skb;
+ sc->ether.tx_ring[last_write].tdes1 |=
+ SBE_2T3E3_TX_DESC_LAST_SEGMENT |
+ SBE_2T3E3_TX_DESC_INTERRUPT_ON_COMPLETION;
+ sc->ether.tx_ring[sc->ether.tx_ring_current_write].tdes0 |=
+ SBE_2T3E3_TX_DESC_21143_OWN;
+ sc->ether.tx_ring_current_write = current_write;
+
+ dev_dbg(&sc->pdev->dev, "txput: tdes0 = %08X tdes1 = %08X\n",
+ sc->ether.tx_ring[last_write].tdes0,
+ sc->ether.tx_ring[last_write].tdes1);
+
+ dc_write(sc->addr, SBE_2T3E3_21143_REG_TRANSMIT_POLL_DEMAND,
+ 0xffffffff);
+
+ spin_unlock_irqrestore(&sc->ether.tx_lock, flags);
+ return 0;
+}
+
+
+void t3e3_read_card_serial_number(struct channel *sc)
+{
+ u32 i;
+
+ for (i = 0; i < 3; i++)
+ sc->ether.card_serial_number[i] = t3e3_eeprom_read_word(sc, 10 + i);
+
+ printk(KERN_INFO "SBE wanPMC-2T3E3 serial number: %04X%04X%04X\n",
+ sc->ether.card_serial_number[0], sc->ether.card_serial_number[1],
+ sc->ether.card_serial_number[2]);
+}
+
+/*
+ bit 0 led1 (green)
+ bit 1 led1 (yellow)
+
+ bit 2 led2 (green)
+ bit 3 led2 (yellow)
+
+ bit 4 led3 (green)
+ bit 5 led3 (yellow)
+
+ bit 6 led4 (green)
+ bit 7 led4 (yellow)
+*/
+
+void update_led(struct channel *sc, int blinker)
+{
+ int leds;
+ if (sc->s.LOS)
+ leds = 0; /* led1 = off */
+ else if (sc->s.OOF)
+ leds = 2; /* led1 = yellow */
+ else if ((blinker & 1) && sc->rcv_count) {
+ leds = 0; /* led1 = off */
+ sc->rcv_count = 0;
+ } else
+ leds = 1; /* led1 = green */
+ cpld_write(sc, SBE_2T3E3_CPLD_REG_LEDR, leds);
+ sc->leds = leds;
+}
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include <linux/kernel.h>
+#include "2t3e3.h"
+
+const u32 cpld_reg_map[][2] =
+{
+ { 0x0000, 0x0080 }, /* 0 - Port Control Register A (PCRA) */
+ { 0x0004, 0x0084 }, /* 1 - Port Control Register B (PCRB) */
+ { 0x0008, 0x0088 }, /* 2 - LCV Count Register (PLCR) */
+ { 0x000c, 0x008c }, /* 3 - LCV Threshold register (PLTR) */
+ { 0x0010, 0x0090 }, /* 4 - Payload Fill Register (PPFR) */
+ { 0x0200, 0x0200 }, /* 5 - Board ID / FPGA Programming Status Register */
+ { 0x0204, 0x0204 }, /* 6 - FPGA Version Register */
+ { 0x0800, 0x1000 }, /* 7 - Framer Registers Base Address */
+ { 0x2000, 0x2000 }, /* 8 - Serial Chip Select Register */
+ { 0x2004, 0x2004 }, /* 9 - Static Reset Register */
+ { 0x2008, 0x2008 }, /* 10 - Pulse Reset Register */
+ { 0x200c, 0x200c }, /* 11 - FPGA Reconfiguration Register */
+ { 0x2010, 0x2014 }, /* 12 - LED Register (LEDR) */
+ { 0x2018, 0x201c }, /* 13 - LIU Control and Status Register (PISCR) */
+ { 0x2020, 0x2024 }, /* 14 - Interrupt Enable Register (PIER) */
+ { 0x0068, 0x00e8 }, /* 15 - Port Control Register C (PCRC) */
+ { 0x006c, 0x00ec }, /* 16 - Port Bandwidth Start (PBWF) */
+ { 0x0070, 0x00f0 }, /* 17 - Port Bandwidth Stop (PBWL) */
+};
+
+const u32 cpld_val_map[][2] =
+{
+ { 0x01, 0x02 }, /* LIU1 / LIU2 select for Serial Chip Select */
+ { 0x04, 0x08 }, /* DAC1 / DAC2 select for Serial Chip Select */
+ { 0x00, 0x04 }, /* LOOP1 / LOOP2 - select of loop timing source */
+ { 0x01, 0x02 } /* PORT1 / PORT2 - select LIU and Framer for reset */
+};
+
+const u32 t3e3_framer_reg_map[] = {
+ 0x00, /* 0 - OPERATING_MODE */
+ 0x01, /* 1 - IO_CONTROL */
+ 0x04, /* 2 - BLOCK_INTERRUPT_ENABLE */
+ 0x05, /* 3 - BLOCK_INTERRUPT_STATUS */
+ 0x10, /* 4 - T3_RX_CONFIGURATION_STATUS, E3_RX_CONFIGURATION_STATUS_1 */
+ 0x11, /* 5 - T3_RX_STATUS, E3_RX_CONFIGURATION_STATUS_2 */
+ 0x12, /* 6 - T3_RX_INTERRUPT_ENABLE, E3_RX_INTERRUPT_ENABLE_1 */
+ 0x13, /* 7 - T3_RX_INTERRUPT_STATUS, E3_RX_INTERRUPT_ENABLE_2 */
+ 0x14, /* 8 - T3_RX_SYNC_DETECT_ENABLE, E3_RX_INTERRUPT_STATUS_1 */
+ 0x15, /* 9 - E3_RX_INTERRUPT_STATUS_2 */
+ 0x16, /* 10 - T3_RX_FEAC */
+ 0x17, /* 11 - T3_RX_FEAC_INTERRUPT_ENABLE_STATUS */
+ 0x18, /* 12 - T3_RX_LAPD_CONTROL, E3_RX_LAPD_CONTROL */
+ 0x19, /* 13 - T3_RX_LAPD_STATUS, E3_RX_LAPD_STATUS */
+ 0x1a, /* 14 - E3_RX_NR_BYTE, E3_RX_SERVICE_BITS */
+ 0x1b, /* 15 - E3_RX_GC_BYTE */
+ 0x30, /* 16 - T3_TX_CONFIGURATION, E3_TX_CONFIGURATION */
+ 0x31, /* 17 - T3_TX_FEAC_CONFIGURATION_STATUS */
+ 0x32, /* 18 - T3_TX_FEAC */
+ 0x33, /* 19 - T3_TX_LAPD_CONFIGURATION, E3_TX_LAPD_CONFIGURATION */
+ 0x34, /* 20 - T3_TX_LAPD_STATUS, E3_TX_LAPD_STATUS_INTERRUPT */
+ 0x35, /* 21 - T3_TX_MBIT_MASK, E3_TX_GC_BYTE, E3_TX_SERVICE_BITS */
+ 0x36, /* 22 - T3_TX_FBIT_MASK, E3_TX_MA_BYTE */
+ 0x37, /* 23 - T3_TX_FBIT_MASK_2, E3_TX_NR_BYTE */
+ 0x38, /* 24 - T3_TX_FBIT_MASK_3 */
+ 0x48, /* 25 - E3_TX_FA1_ERROR_MASK, E3_TX_FAS_ERROR_MASK_UPPER */
+ 0x49, /* 26 - E3_TX_FA2_ERROR_MASK, E3_TX_FAS_ERROR_MASK_LOWER */
+ 0x4a, /* 27 - E3_TX_BIP8_MASK, E3_TX_BIP4_MASK */
+ 0x50, /* 28 - PMON_LCV_EVENT_COUNT_MSB */
+ 0x51, /* 29 - PMON_LCV_EVENT_COUNT_LSB */
+ 0x52, /* 30 - PMON_FRAMING_BIT_ERROR_EVENT_COUNT_MSB */
+ 0x53, /* 31 - PMON_FRAMING_BIT_ERROR_EVENT_COUNT_LSB */
+ 0x54, /* 32 - PMON_PARITY_ERROR_EVENT_COUNT_MSB */
+ 0x55, /* 33 - PMON_PARITY_ERROR_EVENT_COUNT_LSB */
+ 0x56, /* 34 - PMON_FEBE_EVENT_COUNT_MSB */
+ 0x57, /* 35 - PMON_FEBE_EVENT_COUNT_LSB */
+ 0x58, /* 36 - PMON_CP_BIT_ERROR_EVENT_COUNT_MSB */
+ 0x59, /* 37 - PMON_CP_BIT_ERROR_EVENT_COUNT_LSB */
+ 0x6c, /* 38 - PMON_HOLDING_REGISTER */
+ 0x6d, /* 39 - ONE_SECOND_ERROR_STATUS */
+ 0x6e, /* 40 - LCV_ONE_SECOND_ACCUMULATOR_MSB */
+ 0x6f, /* 41 - LCV_ONE_SECOND_ACCUMULATOR_LSB */
+ 0x70, /* 42 - FRAME_PARITY_ERROR_ONE_SECOND_ACCUMULATOR_MSB */
+ 0x71, /* 43 - FRAME_PARITY_ERROR_ONE_SECOND_ACCUMULATOR_LSB */
+ 0x72, /* 44 - FRAME_CP_BIT_ERROR_ONE_SECOND_ACCUMULATOR_MSB */
+ 0x73, /* 45 - FRAME_CP_BIT_ERROR_ONE_SECOND_ACCUMULATOR_LSB */
+ 0x80, /* 46 - LINE_INTERFACE_DRIVE */
+ 0x81 /* 47 - LINE_INTERFACE_SCAN */
+};
+
+const u32 t3e3_liu_reg_map[] =
+{
+ 0x00, /* REG0 */
+ 0x01, /* REG1 */
+ 0x02, /* REG2 */
+ 0x03, /* REG3 */
+ 0x04 /* REG4 */
+};
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/pci.h>
+#include <linux/hdlc.h>
+#include <linux/if_arp.h>
+#include <linux/interrupt.h>
+#include "2t3e3.h"
+
+static void check_leds(unsigned long arg)
+{
+ struct card *card = (struct card *)arg;
+ struct channel *channel0 = &card->channels[0];
+ static int blinker;
+
+ update_led(channel0, ++blinker);
+ if (has_two_ports(channel0->pdev))
+ update_led(&card->channels[1], blinker);
+
+ card->timer.expires = jiffies + HZ / 10;
+ add_timer(&card->timer);
+}
+
+static void t3e3_remove_channel(struct channel *channel)
+{
+ struct pci_dev *pdev = channel->pdev;
+ struct net_device *dev = channel->dev;
+
+ /* system hangs if board asserts irq while module is unloaded */
+ cpld_stop_intr(channel);
+ free_irq(dev->irq, dev);
+ dc_drop_descriptor_list(channel);
+ unregister_hdlc_device(dev);
+ free_netdev(dev);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+ pci_set_drvdata(pdev, NULL);
+}
+
+static int __devinit t3e3_init_channel(struct channel *channel, struct pci_dev *pdev, struct card *card)
+{
+ struct net_device *dev;
+ unsigned int val;
+ int err;
+
+ err = pci_enable_device(pdev);
+ if (err)
+ return err;
+
+ err = pci_request_regions(pdev, "SBE 2T3E3");
+ if (err)
+ goto disable;
+
+ dev = alloc_hdlcdev(channel);
+ if (!dev) {
+ printk(KERN_ERR "SBE 2T3E3" ": Out of memory\n");
+ goto free_regions;
+ }
+
+ t3e3_sc_init(channel);
+ dev_to_priv(dev) = channel;
+
+ channel->pdev = pdev;
+ channel->dev = dev;
+ channel->card = card;
+ channel->addr = pci_resource_start(pdev, 0);
+ if (pdev->subsystem_device == PCI_SUBDEVICE_ID_SBE_2T3E3_P1)
+ channel->h.slot = 1;
+ else
+ channel->h.slot = 0;
+
+ if (setup_device(dev, channel))
+ goto free_regions;
+
+ pci_read_config_dword(channel->pdev, 0x40, &val); /* mask sleep mode */
+ pci_write_config_dword(channel->pdev, 0x40, val & 0x3FFFFFFF);
+
+ pci_read_config_byte(channel->pdev, PCI_CACHE_LINE_SIZE, &channel->h.cache_size);
+ pci_read_config_dword(channel->pdev, PCI_COMMAND, &channel->h.command);
+ t3e3_init(channel);
+
+ if (request_irq(dev->irq, &t3e3_intr, IRQF_SHARED, dev->name, dev)) {
+ printk(KERN_WARNING "%s: could not get irq: %d\n", dev->name, dev->irq);
+ goto free_regions;
+ }
+
+ pci_set_drvdata(pdev, channel);
+ return 0;
+
+free_regions:
+ pci_release_regions(pdev);
+disable:
+ pci_disable_device(pdev);
+ return err;
+}
+
+static void __devexit t3e3_remove_card(struct pci_dev *pdev)
+{
+ struct channel *channel0 = pci_get_drvdata(pdev);
+ struct card *card = channel0->card;
+
+ del_timer(&card->timer);
+ if (has_two_ports(channel0->pdev)) {
+ t3e3_remove_channel(&card->channels[1]);
+ pci_dev_put(card->channels[1].pdev);
+ }
+ t3e3_remove_channel(channel0);
+ kfree(card);
+}
+
+static int __devinit t3e3_init_card(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ /* pdev points to channel #0 */
+ struct pci_dev *pdev1 = NULL;
+ struct card *card;
+ int channels = 1, err;
+
+ if (has_two_ports(pdev)) {
+ while ((pdev1 = pci_get_subsys(PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21142,
+ PCI_VENDOR_ID_SBE, PCI_SUBDEVICE_ID_SBE_2T3E3_P1,
+ pdev1)))
+ if (pdev1->bus == pdev->bus &&
+ pdev1->devfn == pdev->devfn + 8 /* next device on the same bus */)
+ break; /* found the second channel */
+
+ if (!pdev1) {
+ printk(KERN_ERR "SBE 2T3E3" ": Can't find the second channel\n");
+ return -EFAULT;
+ }
+ channels = 2;
+ /* holds the reference for pdev1 */
+ }
+
+ card = kzalloc(sizeof(struct card) + channels * sizeof(struct channel), GFP_KERNEL);
+ if (!card) {
+ printk(KERN_ERR "SBE 2T3E3" ": Out of memory\n");
+ return -ENOBUFS;
+ }
+
+ spin_lock_init(&card->bootrom_lock);
+ card->bootrom_addr = pci_resource_start(pdev, 0);
+
+ err = t3e3_init_channel(&card->channels[0], pdev, card);
+ if (err)
+ goto free_card;
+
+ if (channels == 2) {
+ err = t3e3_init_channel(&card->channels[1], pdev1, card);
+ if (err) {
+ t3e3_remove_channel(&card->channels[0]);
+ goto free_card;
+ }
+ }
+
+ /* start LED timer */
+ init_timer(&card->timer);
+ card->timer.function = check_leds;
+ card->timer.expires = jiffies + HZ / 10;
+ card->timer.data = (unsigned long)card;
+ add_timer(&card->timer);
+ return 0;
+
+free_card:
+ kfree(card);
+ return err;
+}
+
+static struct pci_device_id t3e3_pci_tbl[] __devinitdata = {
+ { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21142,
+ PCI_VENDOR_ID_SBE, PCI_SUBDEVICE_ID_SBE_T3E3, 0, 0, 0 },
+ { PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21142,
+ PCI_VENDOR_ID_SBE, PCI_SUBDEVICE_ID_SBE_2T3E3_P0, 0, 0, 0 },
+ /* channel 1 will be initialized after channel 0 */
+ { 0, }
+};
+
+static struct pci_driver t3e3_pci_driver = {
+ .name = "SBE T3E3",
+ .id_table = t3e3_pci_tbl,
+ .probe = t3e3_init_card,
+ .remove = t3e3_remove_card,
+};
+
+static int __init t3e3_init_module(void)
+{
+ return pci_register_driver(&t3e3_pci_driver);
+}
+
+static void __exit t3e3_cleanup_module(void)
+{
+ pci_unregister_driver(&t3e3_pci_driver);
+}
+
+module_init(t3e3_init_module);
+module_exit(t3e3_cleanup_module);
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, t3e3_pci_tbl);
--- /dev/null
+/*
+ * SBE 2T3E3 synchronous serial card driver for Linux
+ *
+ * Copyright (C) 2009-2010 Krzysztof Halasa <khc@pm.waw.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This code is based on a driver written by SBE Inc.
+ */
+
+#include <linux/capability.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/netdevice.h>
+#include <linux/pci.h>
+#include <linux/hdlc.h>
+#include <linux/if_arp.h>
+#include <linux/interrupt.h>
+#include "2t3e3.h"
+
+int t3e3_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
+{
+ struct channel *sc = dev_to_priv(dev);
+ int cmd_2t3e3, len, rlen;
+ t3e3_param_t param;
+ t3e3_resp_t resp;
+ void *data = ifr->ifr_data + sizeof(cmd_2t3e3) + sizeof(len);
+
+ if (cmd == SIOCWANDEV)
+ return hdlc_ioctl(dev, ifr, cmd);
+ if (!capable(CAP_SYS_ADMIN))
+ return -EPERM;
+ if (cmd != SIOCDEVPRIVATE + 15)
+ return -EINVAL;
+
+ if (copy_from_user(&cmd_2t3e3, ifr->ifr_data, sizeof(cmd_2t3e3)))
+ return -EFAULT;
+ if (copy_from_user(&len, ifr->ifr_data + sizeof(cmd_2t3e3), sizeof(len)))
+ return -EFAULT;
+
+ if (len > sizeof(param))
+ return -EFAULT;
+
+ if (len)
+ if (copy_from_user(¶m, data, len))
+ return -EFAULT;
+
+ t3e3_if_config(sc, cmd_2t3e3, (char *)¶m, &resp, &rlen);
+
+ if (rlen)
+ if (copy_to_user(data, &resp, rlen))
+ return -EFAULT;
+
+ return 0;
+}
+
+static struct net_device_stats* t3e3_get_stats(struct net_device *dev)
+{
+ struct net_device_stats *nstats = &dev->stats;
+ struct channel *sc = dev_to_priv(dev);
+ t3e3_stats_t *stats = &sc->s;
+
+ memset(nstats, 0, sizeof(struct net_device_stats));
+ nstats->rx_packets = stats->in_packets;
+ nstats->tx_packets = stats->out_packets;
+ nstats->rx_bytes = stats->in_bytes;
+ nstats->tx_bytes = stats->out_bytes;
+
+ nstats->rx_errors = stats->in_errors;
+ nstats->tx_errors = stats->out_errors;
+ nstats->rx_crc_errors = stats->in_error_crc;
+
+
+ nstats->rx_dropped = stats->in_dropped;
+ nstats->tx_dropped = stats->out_dropped;
+ nstats->tx_carrier_errors = stats->out_error_lost_carr +
+ stats->out_error_no_carr;
+
+ return nstats;
+}
+
+int t3e3_open(struct net_device *dev)
+{
+ struct channel *sc = dev_to_priv(dev);
+ int ret = hdlc_open(dev);
+
+ if (ret)
+ return ret;
+
+ sc->r.flags |= SBE_2T3E3_FLAG_NETWORK_UP;
+ dc_start(dev_to_priv(dev));
+ netif_start_queue(dev);
+ try_module_get(THIS_MODULE);
+ return 0;
+}
+
+int t3e3_close(struct net_device *dev)
+{
+ struct channel *sc = dev_to_priv(dev);
+ hdlc_close(dev);
+ netif_stop_queue(dev);
+ dc_stop(sc);
+ sc->r.flags &= ~SBE_2T3E3_FLAG_NETWORK_UP;
+ module_put(THIS_MODULE);
+ return 0;
+}
+
+static int t3e3_attach(struct net_device *dev, unsigned short foo1,
+ unsigned short foo2)
+{
+ return 0;
+}
+
+static const struct net_device_ops t3e3_ops = {
+ .ndo_open = t3e3_open,
+ .ndo_stop = t3e3_close,
+ .ndo_change_mtu = hdlc_change_mtu,
+ .ndo_start_xmit = hdlc_start_xmit,
+ .ndo_do_ioctl = t3e3_ioctl,
+ .ndo_get_stats = t3e3_get_stats,
+};
+
+int setup_device(struct net_device *dev, struct channel *sc)
+{
+ hdlc_device *hdlc = dev_to_hdlc(dev);
+ int retval;
+
+ dev->base_addr = pci_resource_start(sc->pdev, 0);
+ dev->irq = sc->pdev->irq;
+ dev->netdev_ops = &t3e3_ops;
+ dev->tx_queue_len = 100;
+ hdlc->xmit = t3e3_if_start_xmit;
+ hdlc->attach = t3e3_attach;
+ if ((retval = register_hdlc_device(dev))) {
+ dev_err(&sc->pdev->dev, "error registering HDLC device\n");
+ return retval;
+ }
+ return 0;
+}
projects / ~emulex / infiniband.git / commitdiff